化学修饰电极的研究及其分析应用

化学修饰电极的出现推动了电化学的发展,是现代电分析化学领域中一个重要的研究方向。本文较详细地评述了化学修饰电极的制备方法及其电分析应用,对其未来发展作了展望。     

Preparation of cobalt hydroxide film modified electrode and its analytical application

Cobalt hydroxide film modified electrode was prepared by depositing cobalt hydroxide on glassy carbon electrode (GCE) surface in an alkaline aqueous solution and then characterized by cyclic voltammetry. The electrochemical behavior of resorcin on the film modified electrode was investigated. The results show that cobalt hydroxide films in alkaline solutions have good electrocatalytical activity towards the oxidation of resorcin. The recovery of resorcin from sample ranged from 95.2 to 103.4% and the oxidation peak currents were directly proportional to the resorcin concentration from 5.0 × 10⁻⁶ to 1.05 × 10⁻⁴ M with correlation coefficient of 0.9986. A detection limit of 1.0 × 10⁻⁷ M for resorcin was estimated. Various factors affecting the electrocatalytical activity of cobalt hydroxide film were investigated in detail. Real water samples were analyzed and satisfactory results were obtained.     

Preparation and application of a thiamine-selective electrode

A thiamine-selective graphite electrode with thiamine tetraphenylborate as the active material in poly(vinyl chloride) and dibutyl phthalate as the plasticizer at pH 2–5 provides a rapid, nearly Nernstian response to thiamine (as a bivalent cation) in the range 10⁻¹ to 10⁻⁵ M. A rapid and accurate potentiometric determination of the thiamine monohydrochloride content of injection and tablet dosage forms is reported with quantitation by the known-addition, dilution method.     

Preparation and application of selenite ion selective electrode

A new selenite ion selective electrode using 4,6-dibromopiaselenole as active material, PVC as membrane matrix and dibutyl phthalate as plasticizer has been developed. An analytically useful potential change occurs from about 10(-6)-10(-1)M Se(IV), and the slope of the linear portion is -23.6 mV/10-fold change in Se(IV) concentration at a temperature of 21 degrees . The electrode shows fairly good selectivity for selenite ion over other anions and has been used for the successful determination of total selenium in human hair.     

Preparation, properties and analytical application of thorium n-phenyl-o-nitrobenzohydroxamate

A new complex of thorium(IV) with N-phenyl-o-nitrobenzohydroxamic acid (PNHA) has been prepared by reacting an aqueous solution of thorium with an alcoholic solution of PNHA at 60 degrees C and adjusting the pH to 4-4.5. The infrared spectra and thermal analysis of the complex are discussed. The use of PNHA for gravimetric determination of thorium is described.     

Construction,analytical study and application of a new chloramine-t selective electrode

A chloramine-T (CAT) selective electrode with a liquid membrane of nickel batho-phenanthroline—chloramine-T dissolved in 2-nitro-p-cymene is described. The liquid membrane electrode exhibits rapid and near Nernstian response to chloramine-T activity from 10^-1 to 10^-4 M. The response is unaffected by pH in the range 5–9. Major interferences are penodate and perchlorate. In analytical applications, direct potentiometnc methods for the determination of chloramme-T, ascorbic acid, and arsenic(III), and a titnmetric method for ascorbic acid are described. Ascorbic acid and arsenic(IU) in the ranges 0.4–40 and 0.5–2 mg, respectively, can be determined with relative errors of 1–2%. The method has been applied to the determination of ascorbic acid in pharmaceutical preparations.     

Electrochemical behavior of dopamine at a quercetin-SAM-modified gold electrode and analytical application

A stable quercetin–thioglycolic acid-modified gold electrode (Qu–TCA/Au) was prepared as a self-assembled monolayer (SAM) and its electrochemical behavior was investigated by electrochemical methods. In 0.05-M phosphate buffer solution (pH 7.0) quercetin exhibits quasi-reversible signals at the Qu–TCA/Au electrode. The stability of the quercetin-modified gold electrode is very good. The quercetin self-assembled monolayer is an effective mediator for the oxidation of dopamine, which was investigated by cyclic voltammetry and differential pulse voltammetry. Ascorbic acid does not interfere with determination of dopamine at an electrode modified with a mixture of quercetin–thioglycolic acid and quercetin–11-mercaptoundecanoic acid. This modification allows dopamine to be determined in the presence of ascorbic acid in the range from 3×10^–5 to 3×10^–4 M. The detection limit is 1×10^–6 M. Scanning electrochemical microscopy (SECM) was employed to study the electrochemical performances of the modified gold electrode indicating different feedback modes at differently modified surfaces.     

Chromatomembrane methods: physicochemical principles, analytical and technological possibilities

Chromatomembrane methods and their origin, physicochemical principles, and analytical and technological possibilities are discussed. Advantages of these methods over traditional schemes of mass-exchange processes in liquid—gas and liquid—liquid systems are shown.     

茜素S选择电极的研制和应用

本文报道了茜素S电极的研制和应用。比较了季铵盐、季鏻盐、碱性染料和邻二氮菲金属配合盐作为活性物质、各种介体溶剂以及活性物质在膜相中的含量对电极性能的影响。以三辛基甲基氯化铵制成的PVC膜型电极对茜素S在2×10~(-4)～5×10~(-7)M浓度范围内呈Nernstian响应,检测下限为2×10~(-7)M。测定了一些阴离子的选择系数,ClO_4~-,CNS~-,I~-以及能与茜素S配合的金属离子有明显干扰。报道了以茜素S电极为指示电极,用EDTA和茜素S为滴定剂滴定钪和稀土的情况。以茜素8电位滴定钪及钴-钐合金中的钐,都获得良好的结果。     

新型平板碳电极的研制与应用

研制了一种新型平板碳电极,用K3Fe(CN)6对电极的性能进行了简单的研究。将该电极用于神经递质多巴胺(DA)的测定,发现在pH 7.0的磷酸盐缓冲介质(PBS)中,多巴胺在该电极上产生一灵敏的氧化峰,峰电流与DA浓度在6.0×10-8~1.0×10-3mol/L范围内呈良好的线性关系,检出限(3σ)为2.0×10-8mol/L。方法可用于人工合成样品的分析。     

Preparation of a polypyrrole-lead dioxide composite electrode for electroanalytical applications

A constant potential electrolytic method for the preparation of a new polypyrrole-lead dioxide composite electrode on glassy-carbon substrate is described. The method involves constant potential electrolysis (CPE) of 1M potassium nitrate containing 2mM lead acetate at + 1.100 V vs. SCE for about 10 min, followed by addition of 25mM pyrrole and subsequent CPE at + 0.800 V for about 2-3 min. The choice of experimental conditions for the preparation and mechanical stability, open circuit potential (ocp) response, background current levels and typical voltammetric response of Mn(2+) in 1M sulphuric acid are also presented and discussed.     

Electrochemical behaviors of metol on ionic-liquid-modified carbon paste electrode and its analytical application

The electrochemical behaviors of metol on an ionic liquid N-butylpyridinium hexafluorophosphate modified carbon paste electrode (IL-CPE) were studied in this paper. The results indicated that a pair of well-defined quasi-reversible redox peaks of metol appeared with the decrease of overpotential and the increase of redox peak current, which was the characteristics of electrocatalytic oxidation. The electrocatalytic mechanism was discussed and the electrochemical parameters were calculated with results of the charge-transfer coefficient (α) as 0.45, the electrode reaction rate constant (k _s) as 4.02 × 10⁻³ s⁻¹, and the diffusion coefficient (D) as 6.35 × 10⁻⁵ cm²/s. Under the optimal conditions, the anodic peak current was linear with the metol concentration in the range of 5.0 × 10⁻⁶ ∼ 1.0 × 10⁻³ mol/L (n = 11, γ = 0.994) and the detection limit was estimated as 2.33 × 10⁻⁶ mol/L (3σ). The proposed method was successfully applied to determination of metol content in synthetic samples and photographic solutions.     

盐酸曲马多离子选择性电极的研制与应用

介绍了盐酸曲马多离子选择性电极的制备,特性以及在药物分析方面的应用。综合考虑活性物质的含量和增塑剂种类及含量的影响,选择了以盐酸曲马多—四苯硼钠缔合物为活性物质,以DOP为增塑剂的电极体系。该电极在5×10-5～1×10-2mol/L范围内表现能斯特响应,斜率为57.1mV/pC,检测下限为1×10-5mol/L。电极对多种异质离子表现良好的选择性。运用电位法测定药物中的盐酸曲马多,回收率为94.9%～106.0%。     

Preparation and analytical evaluation of a new Lead(II) heterogeneous membrane electrode

The preparation of a new lead-seleclive heterogeneous membrane electrode prepared by hot-pressing a mixture of lead and silver sulfides with polythene in a thermomoulding press is described. Nernstian response to lead ion activity, electrode characteristics in terms of concentration, selectivity and interferences, and analytical applications in water and non-aqueous solvents are discussed.     

Preparation of purified spent coffee ground and its reinforcement in natural rubber composite

Spent coffee ground (SCG) contains a variety of organic compounds such as fatty acids, amino acids, polyphenols, polysaccharides, etc. In this study, purification of SCG was carried out by alkalization and bleaching treatment and the purified SCG (PSCG) was characterized by various techniques, i.e., FTIR, XRD, BET, SEM and TGA. PSCG was later treated with Bis-triethoxysilylpropyl tetrasulfide (TESPT). Both PSCG and TESPT-treated PSCG were then incorporated into natural rubber (NR) to investigate their reinforcement magnitude in the bio-composite. Results revealed the eradication of lignin and other non-polysaccharide components after the purification leading to the significant increases in specific surface area and cellulose content of PSCG. Although the addition of PSCG into NR showed cure time reduction in association with the increased modulus and hardness, its reinforcement was not very high due to the large particle size and the abundance of hydroxyl groups in PSCG. The TESPT treatment significantly improved the reinforcement of PSCG due to the increases in rubber-filler interaction and crosslink density. However, the reinforcement of both PSCG and TESPT-treated PSCG is still relatively low compared to the commercial nanofillers and, thus, they can be considered as a cheap and eco-friendly filler in NR.     

Preparation and characterization of Ni(II)/polyacrylonitrile and carbon nanotube composite modified electrode and application for carbohydrates electrocatalytic oxidation

A nickel(II) into porous polyacrylonitrile–carbon nanotubes composite modified glassy carbon electrode (Ni/PAN-CNT/GCE) was fabricated by simple drop-casting and immersing technique. The unique electrochemical activity of Ni/PAN-CNT composite modified glassy carbon electrode was illustrated in 0.10?M NaOH using cyclic voltammetry. The Ni/PAN-CNT/GCE exhibits the characteristic of improved reversibility and enhanced current responses of the Ni(III)/Ni(II) couple compared with Ni/PAN/GCE and Ni/CNT/GCE. The results of electrochemical impedance spectroscopy and scanning electron microscopy indicated the successful immobilization for PAN-CNT composite film. Kinetic parameters such as the electron transfer coefficient, α, and rate constant, k _s, of the electrode reaction were determined. Ni/PAN-CNT/GCE also shows good electrocatalytic activity toward the oxidation of carbohydrates (glucose, sucrose, fructose, and sorbitol). The electrocatalytic response showed a wide linear range (10–1,500, 12–3,200, 7–3,500, and 16–4,200?μM for glucose, sucrose, fructose, and sorbitol, respectively) as well as its experimental limit of detection can be achieved 6, 7, 5, and 11?μM for glucose, sucrose, fructose, and sorbitol, respectively. The modified electrode for carbohydrates determination is of the property of simple preparation, good stability, and high sensitivity.     

Three-dimensional bundle-like multiwalled carbon nanotubes composite for supercapacitor electrode application

Bundle-type mutil-walled carbon nanotubes (MWCNTs) composite electrode is the first investigation and publication for the supercapacitor application. According to the thermogravimetric analysis results, as-synthesized BCNTs are considered as the electrode materials for supercapacitors and electrochemical double-layer capacitor in this study. The Brunauer–Emmett–Teller specific surface area of as-prepared bundled carbon nanotubes (BCNTs) is 95.29 m²/g given to a type III isotherm and H3 hysteresis loops. Slow scanning rates promote and enhance to achieve high C_b because of the superior conductivity of CNT bundles and one side close-layered Ni/Mg/Mo alloy inside the BCNT-based electrode and facile electron diffusivity between electrolyte and electrode. The specific capacitance C_s (1,560 F/g) is nearly equal to the maximum specific capacitance, which the BCNT-based composite electrode can actually be able to charge or fill in. The maximum energy density value is 195 Wh/kg with corresponding power density values of 0.21 kW/kg. Furthermore, the active 3D BCNTs material fabricated electrode enhances to contact the electrolyte directly and decreases the ion diffusion limitation. Electrochemical impedance spectroscopy spectrum summarized as the low-frequency area controls by mass transfer limitation, and the high-frequency area dominates by charge transfer of kinetic control. After 2,000 consecutive cyclic voltammetry sacnings and galvanostatic charge-discharge cycles at a current density of 1.67 A/g performs, the specific capacitance retentions of 3D BCNTs electrodes achieved 128.2 and 77.3%, respectively. Three-dimensional BCNT composite electrodes exhibit good conductivity and low charge transfer resistance, which is beneficial to fast charge transfer between the BCNTs electrode materials and electrolytes.     

Improvement of the analytical possibilities of dual-column ion-chromatography

Summary Dual-column ion-chromatography is an effective method for determining organic and inorganic ions, especially anions, in different natural and industrial objects. In a number of cases, however, some problems occur limiting its analytical possibilities. These problems are connected with the limited choice of eluents and sorbents, with insufficient selectivity for some objects, unsatisfactory rapidity of determination, and with the occurrence of water dips and system peaks in the chromatogram. In order to solve these problems and improve the analytical possibilities of dualcolumn ion-chromatography it is suggested to use aminoacid eluents, stepwise elution and complex formation of the ions being determined and eluted.

---

Verbesserung der analytischen Möglichkeiten der Doppelsäulen-Ionen-Chromatographie

     

聚苯胺-邻氨基酚膜修饰电极的制备及其应用

通过循环伏安法(CV)将苯胺(AN)-邻氨基酚(OAP)修饰在玻碳电极(GCE)表面,制备出聚苯胺-邻氨基酚聚合物膜修饰电极(PAN-OAP/GCE),并用该电极对抗坏血酸(AA)进行测定。分别对OAP与AN聚合浓度比和磷酸缓冲溶液(PBS)pH进行优化。结果表明OAP与AN浓度比为1:14,pH为6.80时,所得聚合物膜修饰电极具有良好的电化学催化活性和稳定性。同时,在0.1 mol/L PBS(pH 6.80)中,采用差分脉冲伏安法(DPV)对AA进行测定,结果表明PAN-OAP/GCE电极对AA具有明显的电化学催化氧化作用,且AA在膜修饰电极上的响应电流和其浓度在1.50×10-8～2.12×10-6mol/L范围内呈良好的线性关系,线性回归方程为ip=1.0344c+0.0183,相关系数为0.9988。检测限可达5.0×10-9mol/L。该修饰电极具有较高的灵敏度和选择性,用于样品中AA的检测,回收率为96.0%～101.2%。