Critical behavior of Fe15Ni65B18Si2 ferromagnetic glass

AC susceptibility, magnetization and electrical resistivity around the Curie temperature (T_c) were measured for Fe₁₅Ni₆₅B₁₈Si₂ glass. The results yield T_c = (307.6±0.1) K and the following critical exponents γ = 1.50±0.03, β = 0.375±0.01, δ = 5.1±0.1 andα = -0.29±0.05. These values were obtained in the reduced temperature interval $\text{1×10}{}^{-3}\text{?}\text{|T?T}{}_{\mathrm{c}}\text{|}\text{T}{}_{\mathrm{c}}\text{?5 ×10}{}^{-2}$. In spite of the fact that these values for the critical exponents were obtained from different measurements they obey the equality relations γ = β(δ?1) and γ+2β+α = 2. Reduced magnetisation and field follow a magnetic equation of state derived for a second-order phase transition over a wide temperature range. This set of critical exponents is compared with those derived from the Heisenberg model as well as with the usual ones for a pure crystalline ferromagnets. The comparison shows that the values of |α| and γ, for our alloy, are considerably larger than those from the model and the usual crystalline ones. A similar difference is also observed in some other amorphous and dilute crystalline ferromagnets and is probably due to magnetic inhomogeneities.     

Magnetic force microscopy characterization of heat and current treated Fe40Ni38Mo4B18 amorphous ribbons

The domain structure of a magnetostrictive Fe₄₀Ni₃₈Mo₄B₁₈ amorphous ribbon has been studied using magnetic force microscopy (MFM) at room temperature. First, the evolution of the magnetic domain patterns as a function of the annealing temperature has been investigated. In samples heat treated at 250 and 450 °C for 1 h, a transformation from 90° to 180° domain wall has been clearly observed, while the sample heat treated at 700 °C for 1 h showed a magnetic phase fixed by the crystalline anisotropy. Additionally, the evolution of the magnetic domain structure by applying a DC current was recorded by the MFM technique. For current annealed samples at 1 A for 1, 30 and 60 min, a transformation between different domain patterns has been observed. Finally, in samples treated by the current annealing method under simultaneous stress, an increase of the annealing time gives rise to a different magnetic structure arising from the development of transverse magnetic anisotropy.     

Crystallization kinetics of the Fe40Ni38Mo4B18 amorphous alloy

X-ray diffraction (XRD) and Mössbauer spectroscopy were used to study the annealing of the Fe₄₀Ni₃₈Mo₄B₁₈ amorphous alloy. The samples were isothermally annealed in the 858–878 K temperature range several times. Two crystalline phases were observed in the annealed samples: FeNi₃ and (Fe, Ni, Mo)₂₃B₆. Preliminary results indicate that assuming a linear relationship between the area under the main XRD peak associated with the FeNi₃ phase and its volume fraction, this can be fitted to a Johnson–Mehl–Avrami equation with an exponent n close to 1.0. Mössbauer results show a broad magnetic hyperfine field distribution in as-received samples and, consistent with XRD results, a sextet attributed to precipitates of FeNi₃ (B_hf=29.5 T) for long annealing times.     

Stoner excitations in the strong itinerant amorphous ferromagnets FexNi80−xB18Si2 and Fe80B20

Accurate measurements of the static magnetization of the amorphous ferromagnets Fe_xNi_80?xB₁₈Si₂ (x = 15, 20, 40, 60%) and Fe₈₀B₂₀ are reported. The results are analyzed in terms of spin-wave and Stoner excitations, and the latter indicate strong itinerant ferromagnetism with a Stoner gap Δ varying between 20 and 60 K. The other fitting parameters give values of the spin-wave stiffness and a quantity simply related to the saturation magnetization. The well-known anomaly regarding the spin-wave stiffness observed in earlier measurements in thus explained quantitatively.     

Synthesis and magnetic properties of Au-coated amorphous Fe20Ni80 nanoparticles

Gold-coated nanoparticles of Fe₂₀Ni₈₀ (permalloy) have been synthesized by a microemulsion process. The as-prepared samples consist of ∼5 nm diameter particles of amorphous Fe₂₀Ni₈₀ that are likely encapsulated in B₂O₃. One or more Fe₂₀Ni₈₀@B₂O₃ particles are subsequently encapsulated in 8-20 nm gold nanospheres, as determined by TEM and X-ray powder diffraction (XRD) line broadening. The gold shells were found to be under expansive strain. Magnetic data confirm the existence of a superparamagnetic phase with a blocking temperature, T_B, of ∼33 K. The saturation magnetization, M_S, of the as-prepared, Au-coated sample is ∼65 emu g⁻¹ at 5 K and ∼16 emu g⁻¹ at 300 K. The coercivity, H_C, is ∼280 Oe at 5 K.     

金属玻璃(Fe0.8Ni0.15Cr0.05)78Si8B14的起始磁导率减落现象

在77—553K范围内的不同温度下测量了金属玻璃(Fe_0.8Ni_0.15,Cr_0.05)₇₈Si₈B₁₄的起始磁导率减落。测量结果表明,减落的温度关系表现为一个具有单一弛豫峰的不对称谱。在273K下考察了减落的动力学行为。用Hesse-Rubartsch方法拟合动力学曲线得到一个左右不对称的单峰激活能谱,最可几激活能大约为1.40eV。考察了减落的退火效应及退火动力学行为,结果表明,在宽的温度范围内,减落呈现明显的退火效应,而且退火动力学行为近似服从lnt动力学。 关键词：     

Hyperfine field distribution in amorphous Fe40Ni40B20

From the Mössbauer investigation of amorphous Fe₄₀Ni₄₀B₂₀ and Fe₈₀B₂₀ alloys it was found that the substitution of Fe by Ni only shifts but does not influence the shape of the iron hyperfine field distribution contrary to that of crystalline f.c.c. Ni-Fe alloys suggesting a rather localized type of behaviour. The distributions of the linear combinations of isomer shift and quadrupole splitting are affected by this substitution.     

Stress-induced magnetic easy axis in amorphous Fe40Ni40P14B6

In a ribbon of amorphous Fe₄₀Ni₄₀P₁₄B₆ (Metglas 2826) the iron spins tend to be parallel to the plane of the ribbon, but the distribution of spin directions within the plane is nearly random. When a uniaxial tensile stress is applied to the ribbon the spins become almost completely aligned parallel to the applied stress. The technique of Mössbauer polarimetry was used to detect and measure this effect.     

Microstructure evolution in the rapidly quenched Fe78Si9B13 ribbons

We report microstructure evolution in as-spun Fe₇₈Si₉B₁₃ ribbons under various wheel speeds (s), which was investigated by X-ray diffraction (XRD), differential scanning calorimetry (DSC), and transmission electron microscopy (TEM). With decreasing s, the volume fraction of the residual amorphous phase (V_a) in the as-spun ribbons decreases gradually, and the total exothermic heat of the crystallization in the DSC curves also decreases, but the ratio of the exothermic heat of the second crystallization to the first one is on the contrary. α-Fe is found in the ribbon with s of 32.9 m/s, while α-Fe, eutectic α-Fe+Fe₂B, and Fe₃Si phases are found in ribbons with s of 25.6 and 18.3 m/s. The phase precipitating behavior in cooling processes is well consistent with the annealing process in the literatures.     

Transversal magnetic field effect on Fe40Ni40P14B6 amorphous alloys

A study about the influence of an electric current flowing through an amorphous ribbon Fe₄₀Ni₄₀P₁₄B₆ has been done. It has been found that the magnetization curves are strongly influenced by such a current (from 0 up to 5000 Hz). Bitter patterns under the action of the current have been observed in order to gain a better knowledge of these effects. The wall energy has been evaluated from a simple model.     

频率对纳米晶软磁合金磁性能影响的理论解释

根据原子力显微镜（AFM）对Fe基纳米晶Fe_735Cu₁Nb_{3< /sub>Si135B9合金薄带的介观结构的研究结果，提出了解释纳米晶软磁合金磁性能的理论模型——柱、球混合模型，并成功地解释了频率对纳米晶软磁合金磁性能的影响，所得理论体现了Herzer理论和纪松理论的特点，并弥补了它们的不足，同时提出了纳米晶粒电导率σ、磁导率μ对合金磁性有影响的观点. 关键词： 铁基纳米晶合金 模型 频率 软磁性能}     

Recoilless fraction, structural, magnetic and thermal properties of Fe73.5Cu1Nb3Si13.5B9 alloy

Differential scanning calorimetry, X-ray diffraction and room temperature Mössbauer spectrum measurements of Fe_73.5Cu₁Nb₃Si_13.5B₉ (Finemet) alloy have been carried out in order to study its structural and magnetic properties as a function of annealing temperature. The DSC profile of as-quenched Finemet showed two exothermic peaks at 530 and 702 °C, corresponding to two crystallization processes. The Finemet alloy remains amorphous at 450 °C with one broad peak in XRD pattern and one broad sextet in Mössbauer spectrum. When the Finemet alloy was annealed at 550 °C, only well indexed body-center-cubic phase was detected. After being annealed at 650 and 750 °C, the XRD patterns showed the coexistence of α-Fe(Si) and Fe-B intermetallic phases with the increase in XRD peak intensities, indicating the growth of crystallites and the decomposition of Fe_73.5Cu₁Nb₃Si_13.5B₉ alloy at elevated temperatures. The Mössbauer spectra of annealed Finemet alloy could be fitted with 4 or 5 sextets and one doublet at higher annealing temperatures, revealing the appearance of different crystalline phases corresponding to the different Fe sites above the crystallization temperature. The appearance of the nanocrystalline phases at different annealing temperatures was further confirmed by the recoilless fraction measurements.     

非晶态Fe13.3Ni69.6B16.2Si0.9的结构驰豫

本文讨论了非晶合金Fe_13.3Ni_69.6B_16.2Si_0.9的结构弛豫动力学及可逆弛豫过程,研究了各种热处理引起居里温度T_c的变化。发现经长时间退火后T_c趋于平衡值且动力学可通过弛豫时间连续谱加以描述。可逆弛豫过程可用CSRO来说明,并且某一物理量的可逆变化并不意味着整个结构的变化是可逆的。 关键词：     

Annealing effect on soft magnetic properties and magnetoimpedance of Finemet Fe73.5Si13.5B9Nb3Au1 alloy

Effect of annealing on the soft magnetic properties of Fe_73.5Si_13.5B₉Nb₃Au₁ amorphous ribbon has been investigated by means of structure examination, magnetoimpedance ratio (MIR) and incremental permeability ratio (PR) spectra measured in the frequency range of 1–10 MHz at a fixed current of 10 mA X-ray diffraction analysis showed that the as-cast sample was amorphous and it became nanocrystalline under a proper heat treatment. When annealing amorphous alloy at 530 °C for 30, 60, 90 min, soft magnetic properties have been improved drastically. Among the samples investigated, the sample annealed at 530 °C for 90 min showed the softest magnetic behavior. The MIR and PR curves revealed the desirable changes in anisotropy field depending upon annealing.     

On the structure of amorphous Fe84B16

The structure of an amorphous alloy of Fe₈₄B₁₆ has been investigated by X-ray diffraction. The results suggest that the atomic distribution of amorphous Fe₈₄B₁₆ differs slightly from those of other amorphous systems such as amorphous Fe and Fe₈₃P₁₇.     

Magnetic thermoelectric power of Fe20Ni60B10Si10 metallic glass

The magnetic contribution to the thermoelectric power was separated for the metallic glass Fe₂₀Ni₆₀B₁₀Si₁₀ which exhibits the ferro-paramagnetic transition at T_c = 455 K remarkably below the crystallization threshold T_x = 670 K. Results are compared with the predictions of the Kasuya theory.     

A Mössbauer study of amorphous Fe40Ni40B20

Amorphous Fe₄₀Ni₄₀B₂₀ (VITROVAC 0040) alloy has been investigated using ⁵⁷Fe Mössbauer Spectroscopy. The Curie temperature T_c is found to be well defined and is 695 ± 1 K. The quadrupole splitting just above T_c is 0.64 mm sec^?1. The crystallization temperature is 698 ± 2 K, close to but definitely above T_c. The average hyperfine field H_eff(T) of the glassy state shows a temperature dependence of $\text{H}{}_{\mathrm{<mtext>eff</mtext>}}\text{(0)[1 ? B}{}_{\mathrm{<mtext>3</mtext><mtext>2</mtext>}}\text{(T/T}{}_{\mathrm{c}}\text{)}{}^{\mathrm{<mtext>3</mtext><mtext>2</mtext>}}\text{? C}{}_{\mathrm{<mtext>5</mtext><mtext>2</mtext>}}\text{(T/T}{}_{\mathrm{c}}\text{)}{}^{\mathrm{<mtext>5</mtext><mtext>2</mtext>}}\text{? …]}$ indicative of the existence of spin wave excitations. The values of $\text{B}{}_{\mathrm{<mtext>3</mtext><mtext>2</mtext>}}$ and $\text{C}{}_{\mathrm{<mtext>5</mtext><mtext>2</mtext>}}$ are found to be 0.40 and 0.06, respectively, for T/T_c ? 0.72. At temperatures close to T_c, H_eff(T) varies as (1 ? T/T_c)^β where β is one of the critical exponents and its value is found to be 0.29 ± 0.02.     

Mössbauer study of the in-plane anisotropy in annealed amorphous Fe81B13.5Si3.5C2 ribbons

Mössbauer spectra of amorphous Fe₈₁B_13.5Si_3.5C₂ ribbons (METGLAS 2605 SC) annealed in transverse magnetic field at 594 and 654 K were recorded for various orientations of the ribbons. It is determined that the in-plane projection of the anisotropy is 17° off the transverse axis for the 594 K annealed specimen and 10° off the transverse axis for the 654 K specimen.