Self-assembled films based on polypyrrole and carbon nanotubes composites for the determination of Diuron pesticide

In this work, polypyrrole (PPy) and its respective composite with functionalized multi-walled carbon nanotubes (MWCNT) were obtained by chemical polymerization of the monomer pyrrole in aqueous solution. The obtained PPy as well as its composite (PPy-MWCNT) were characterized by Fourier transform infrared spectroscopy (FTIR) and were used to produce nanostructured self-assembled (SA) films deposited onto glass substrates covered with indium tin oxide (ITO). The SA films were produced with alternated layers of polystyrene sulphonated (PSS) and were characterized by UV-visible, cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), and scanning electron microscopy (SEM) analyses. The applicability of the SA films was evaluated by square wave voltammetry (SWV) with standard additions of aliquots of Diuron pesticide in Britton-Robinson buffer solutions (pH = 2.0). The results showed an oxidation peak at 0.23 V which increases in function of the Diuron concentration for both the SA films. It was also observed that the SA film based on the composite (PPy-MWCNT/PSS) showed a peak current intensity about ten times higher in comparison with its unmodified counterpart (PPy/PSS) for a Diuron concentration of 4.29 × 10^?5 mol L^?1, indicating a synergic effect between PPy and MWCNT in the composite. The limits of quantification (LOQ) and limits of detection (LOD) were respectively 8.6 × 10^?7 mol L^?1 and 2.6 × 10^?7 mol L^?1.     

Effect of acid treatment of Corich core–Ptrich shell/C electrocatalyst on oxygen reduction reaction

Co_{rich core}–Pt_{rich shell}/C prepared by thermal decomposition and chemical reduction methods were treated by 20% H₂SO₄ aqueous solution and used as the electrocatalysts for the oxygen reduction reaction (ORR). The particle size range of Co_{rich core}–Pt_{rich shell} (molar ratio of 0.92:1) on carbon powder support decreased from 3–8 to 1–6 nm when the time for the electrocatalysts immersed and treated with 20% H₂SO₄ aqueous solution increased from 0 to 4 h. Using Co_{rich core}–Pt_{rich shell} (molar ratio of 0.92:1)/C treated with 20% H₂SO₄ from 0 to 4 h as the working electrode, the open circuit potential of ORR in 0.5 M HClO₄ aqueous solution increased from 0.9995 to 1.0155 V, and the current density, mass activity, and specific activity at the overpotential of 0.1 V increased from 0.619 mA cm^?2, 6.184 A g^?1, and 18.614 μA cm^?2 to 0.912 mA cm^?2, 15.544 A g^?1, and 23.413 μA cm^?2, respectively.     

The conducting polymer electrolyte based on polypyrrole-polyvinyl alcohol and its application in low-cost quasi-solid-state dye-sensitized solar cells

The effect of polypyrrole (PPy) on the polyvinyl alcohol (PVA)-potassium iodide (KI)-iodine (I₂) polymer electrolytes has been investigated and optimized to use in a dye-sensitized solar cell (DSSC). The different weight ratios of PVA: PPy (93: 2, 91: 4, 89: 6, 87: 8, and 85: 10 wt%) polymer electrolytes (PE) were prepared by solution casting. Structural, complex formation and surface roughness of the prepared electrolytes was confirmed by X-ray diffraction, FTIR, and atomic force microscopy (AFM) respectively. Conductivity plots of all polymer films showed increasing trend with temperature and concentration of PPy. The activation energy of the optimized system found to be 0.871 kJ mol^?1. UV-visible spectrum was adopted to characterize the absorption spectra of the material revealed that increase in the absorbance with increasing PPy content and shifting the absorbance maximum towards lower energy. The indirect band gap decreased from 3.78 to 2.14 eV and direct band gap decreased from 3.88 to 2.71 eV. The EIS analyses revealed the lower charge transfer resistance of 3.029 Ω cm² at the interface between CE and PE. The excellent performance was observed in the fabricated DSSCs using PVA (85%)/PPy (10%)/KI (5%)/I₂ polymer electrolyte with a short-circuit current density of 11.071 mA cm^?2, open-circuit voltage of 0.644 V, fill factor of 0.575, and photovoltaic conversion efficiency of 4.09% under the light intensity of 100 mW cm^?2. Hence, the PPy content in polymer electrolyte influences the remarkable performance of low-cost DSSC.     

A facile one-pot interfacial synthesis of Pt nanoparticles/polypyrrole composites and their application for non-enzymatic sensing hydrogen peroxide

Pt nanoparticles (PtNPs)/polypyrole (PPy) composites were successfully prepared through a facile one-pot interfacial polymerization of pyrrole by using H₂PtCl₆ as the oxidant for the first time. The as-prepared PPy was granular particles with particle size within a few hundred nanometers, on which PtNPs (1.7–3.5) nm were homogeneously dispersed. The PtNPs/PPy composites displayed excellent electrocatalytic activity toward redox of H₂O₂. The non-enzyme sensor constructed with PtNPs/PPy composites displayed good sensing ability toward H₂O₂ at ?0.1 V with a significantly high sensitivity of 6056 μAmM^?1cm^?2 and a low detection limit of 1.8 μM (S/N = 3).     

Optimizing the preparation conditions of polypyrrole electrodes for enhanced electrochemical capacitive performances

Here, we put forward an optimum proposal to prepare high-performance polypyrrole (PPy) electrodes for supercapacitor applications. A detailed study regarding the effects of different preparation conditions including electropolymerized mode, parameter, and current collector on the electrochemical capacitive performances of PPy electrodes is carried out. Fourier transform infrared spectroscopy and X-ray diffraction tests indicate the above preparation conditions have no effect on the component and crystal structure of PPy prepared. Electrochemical measurements manifest a significant effect of current collector on supercapacitive properties of PPy electrodes. Graphite foil as the current collector with low resistance shows remarkably superior capacitive performances compared with FTO-conducting glass and ITO conductive plastic. SEM characterizations show galvanostatically polymerized PPy particles have obviously smaller aggregation degree than potentiostatically polymerized PPy particles, which results in better electrochemical properties for former. Among different preparation conditions, the PPy deposited on graphite foil under galvanostatic mode with 2 mA cm^?2 shows the best electrochemical capacitive properties. The optimized PPy/graphite electrodes show a high specific capacitance of 173.0 mF cm^?2 at 0.2 mA cm^?2, superior rate capability, and outstanding cycling stability (retaining 90.5% of initial capacitance for 5000 cycles).     

Mesoporous carbon nitride loaded with Pt nanoparticles as a bifunctional air electrode for rechargeable lithium-air battery

A composite comprised of oxygen reduction reaction (ORR) catalyst and oxygen evolution reaction (OER) catalyst was designed and applied as a bifunctional electrocatalyst for the air electrode of the lithium-air battery. The ordered mesoporous carbon nitride (MCN) prepared by a nano hard-templating approach displayed a surface area as high as 648 m² g^?1 and a large pore volume of 0.7 cm³ g^?1 and acted as both the ORR catalyst and the support for the in situ-formed OER catalyst of Pt particles with a diameter of 3–4 nm. The electrochemical performances of the electrode were examined in a solid-state lithium-air cell structured as Li/LATP-based electrolyte/cathode, which demonstrated a higher round-trip efficiency and lower overpotential compared with the Pt@AB and MCN electrodes. The combination of the OER and ORR catalysts is proved as an effective way to improve the performance of lithium-air batteries.     

Nickel oxide nanoparticles prepared by gelatin and their application toward the oxygen evolution reaction

Green synthesis of pure nickel oxide nanoparticles (nano-NiO) in aqueous medium has been carried out using gelatin. The particles have been characterized using transmission electron microscopy (TEM), X-ray diffraction (XRD), scanning electron microscopy (SEM), and energy dispersive X-ray (EDAX). Gelatin plays an important role in the formation of the nano-NiO. TEM image shows the formation of nano-NiO with average particle size 16 nm, which agrees well with the XRD data. Moreover, efficient and stable nano-NiO-based anodes were fabricated by casting of the nano-NiO and multi-walled carbon nanotube solution (NiO-MWNT) on glassy carbon (NiO-MWNT/GC), platine (NiO-MWNT/Pt), and carbon paste (NiO-MWNT/CP) electrodes. The electrocatalysis of oxygen evolution reaction (OER) at modified electrodes has been examined using linear scanning voltammetry (LSV). The OER is significantly enhanced upon modification of the electrodes with NiO-MWNT, as demonstrated by a negative shift in the LSV curves at the NiO-MWNT-modified electrodes compared to that obtained at the unmodified ones. The maximum electrocatalytic activity toward the OER was obtained in alkaline media. The values of energy saving of oxygen gas at a current density of 5 mA cm^?2 Pt, CP, and GC electrodes are 14.1, 16.0, and 21.6 kW h kg^?1, respectively. The low cost as well as the marked stability of the modified electrodes makes them promising candidates in industrial water electrolysis process.     

Microstructural and Potential Dependence Studies of Urease-Immobilized Gold Nanoparticles–Polypyrrole Composite Film for Urea Detection

Gold nanoparticle–polypyrrole nanocomposite film was electrochemically deposited in a single-step polymerization of pyrrole in the presence of 3-mercaptopropionic acid (MPA)-capped gold nanoparticles (GNPs) and p-toluenesulfonic acid (pTSA) on the surface of an indium tin oxide (ITO)-coated glass plate. The carboxyl functional groups surrounding the GNPs within the polymer matrix were utilized for the immobilization of urease enzyme through carbodiimide coupling reaction for the construction of a Urs/GNP(MPA)–PPy/ITO-glass bioelectrode for urea detection in Tris–HCl buffer. The resulting bioelectrode film was characterized by atomic force microscopy (AFM), high-resolution transmission electron microscopy (HRTEM), contact angle measurement, Fourier transform infrared spectroscopy (FTIR), and electrochemical techniques. The potentiometric response of the bioelectrode made of polymer nanocomposite films of two different thicknesses prepared at 100 and 250 mC cm^?2 charge densities, respectively, was studied towards the urea concentration in Tris–HCl buffer (pH 7.4). The thin polymer nanocomposite film-based bioelectrode prepared at 100 mC cm^?2 charge density exhibited a comparatively good potentiometric response than a thick 250 mC cm^?2 charge density film with a linear range of urea detection from 0.01 to 10 mM with a sensitivity of 29.7 mV per decade.     

The electrochemical behavior of PtRu- and Pt-modified zeolite X in alkaline solution

Zeolite NaX was modified by Pt and Pt/Ru nanodispersed metallic clusters. The procedure of impregnation with acetylacetonate salt/acetone solution was applied. Scanning electron microscope analysis confirmed partial zeolite framework destruction. According to energy dispersive X-ray analysis, Pt/Ru ratio in sample was about 1. Electrochemical behavior of PtRu- and Pt-modified zeolites was investigated in alkaline solutions, 5 mM NaOH?+?1 M Na₂SO₄ and 0.1 M NaOH. The shape of cyclic voltammograms of 13XPtRu electrode, recorded in slightly alkaline solution, was greatly affected by the presence of hydrogen that remained in the sample after synthetic procedure. Oxygen reduction reaction (ORR) was investigated in an O₂-saturated aqueous 0.1-M NaOH solution. The obtained Tafel slopes indicated ORR mechanism that involves one-electron discharge-determining step. According to Koutecky–Levich slope, the oxygen reduction reaction followed 4e^? mechanism on both 13XPtRu and 13XPt electrode. The onset of ORR on 13XPtRu electrode was shifted toward more positive potentials in comparison to 13XPt electrode.     

Oxygen reduction on electrodeposited silver catalysts in alkaline solution

In this study, silver was electrochemically deposited onto glassy carbon (GC) substrate using constant potential regime and tested for oxygen reduction reaction (ORR) in alkaline media. The surface morphology of Ag/GC electrodes was studied by scanning electron microscopy (SEM). It was established that after 10 s of deposition, a number of Ag nanoparticles with the size of 15 nm are produced that grow to about 45 nm after 300 s of electrodeposition. The ORR studies were conducted in 0.1 M KOH solution employing the rotating disk electrode (RDE) method. The Tafel slope at low current densities for electrodeposited silver is in the range from ?70 to ?80 mV. The RDE measurements showed that the electron transfer number (n) is 3.5 for smaller amounts of electrodeposited Ag, and it increases with increasing the loading of Ag on the GC surface. These n values suggest that the electroreduction of oxygen on Ag/GC electrodes proceeds mainly to water.     

Ultra-high surface area and mesoporous N-doped carbon derived from sheep bones with high electrocatalytic performance toward the oxygen reduction reaction

A nitrogen (N)-doped mesoporous carbon material exhibiting ultra-high surface area was successfully synthesized from sheep bones via a facile and low-cost method. The obtained carbon material had an ultra-high specific surface area of 1961 m² g^?1 and provided rich active sites for the oxygen reduction reaction (ORR), which in turn resulted in high electrocatalytic activity. It was found that the pore size distribution for the newly prepared carbonaceous material fell in the range of 1–4 nm. Benefiting from its high surface area and the presence of pyridine-N and quaternary-N species, the as-prepared carbon material exhibited excellent ORR activity in an oxygen-saturated 0.1 M KOH solution, compared to commercial Pt/C (10 wt%). Due to its high ORR catalytic activity, stability and low-cost, using sheep bone as C and N precursors to produce N-doped carbon provides an encouraging step toward the goal of replacing commercial Pt/C as fuel cell cathode electrocatalyst.     

Novel preparation of electrically conducting poly (vinyl chloride) by photo-dehydrochlorination from poly (vinyl chloride)/polypyrrole composite film

Polypyrrole (PPy) was deposited electrochemically on a platinum plate from a nitric acid solution of pyrrole. The PVC/PPy composite film was finally obtained by casting poly(vinyl chloride) (PVC) onto the PPy electrode from a tetrahydrofuran solution of PVC. The prepared composite film was irradiated at 90°C with a low-pressure mercury lamp in the stream of hydrogen gas saturated with steam, and the PVC film was dehydrochlorinated, leading to the formation of conjugated polyene. The electrical conductivity (σ) of the PVC film in the irradiated composite film was reveled: σ=2.51 × 10^?5S cm^?1. By iodine doping, σ was further enhanced up to 5.04 X 10^?3 S cm^?1. The tensile strength of the irradiated composite film became larger than that of the original PVC film; i.e., the stress at break was: 461 (composite film); 401 kg cm^?2 (PVC). These results were brought about by the doping of radical species to the conjugated polyene. The anion, NO^?₃, doped during the electrodeposition of PPy was photodecomposed to generate radical NO₂ and this species was doped to the polyene, resulting in the formation of electrically conductive PVC and mechanically improved composite film. © 1994 John Wiley & Sons, Inc.     

Hemin-adsorbed carbon felt for sensitive and rapid flow-amperometric detection of dissolved oxygen

Hemin was physically adsorbed onto porous carbon felt (CF), a microelectrode ensemble of micro-carbon fiber (ca. 7 μm in diameter) and possessing a three-dimensional random structure. The hemin-CF exhibited a well-defined redox wave that is due to Fe(III)/Fe(II) redox process in hemin, with a formal potential of ?0.32 V (vs. Ag/AgCl) in deoxygenated buffer solution of pH 7.0. The surface coverage of the electroactive hemin molecules on the surface of the CF was calculated to be 5.0?×?10^?11 mol cm^?2, and the apparent heterogeneous electron transfer rate constant is 3.35 s^?1. The hemin-CF electrode displays excellent electrocatalytic activity for the reduction of dissolved oxygen (DO), and the magnitude of the cathodic current increases with increasing concentrations of DO in the sample solution. The electrode was used as a flow-through detector for sensitive and rapid consecutive determination of DO. Deoxygenated pH 7.0 solutions were analyzed at a flow rate of 8.0 mL min^?1 at an applied potential of ?0.2 V, and highly reproducible cathodic peak current responses to DO were observed in the 0.72 to 13.3 mg L^?1 concentration range. The maximum throughput is 170 samples h^?1. The hemin-CF-based amperometric flow-sensor was applied to determine the concentration of DO in environmental water samples.

Graphitic C<Subscript>3</Subscript>N<Subscript>4</Subscript>@MWCNTs supported Mn<Subscript>3</Subscript>O<Subscript>4</Subscript> as a novel electrocatalyst for the oxygen reduction reaction in zinc–air batteries

A series of catalysts (g-C₃N₄@MWCNTs/Mn₃O₄) were prepared from g-C₃N₄, MWCNTs, and Mn₃O₄ for oxygen reduction reaction (ORR) in zinc–air batteries. From the half-cell tests, the loading of 35 % Mn₃O₄ (sample GMM35) presents an excellent activity toward ORR in alkaline condition. Rotating ring-disk electrode (RRDE) studies reveal that 3.6～3.8 electrons are transferred with a H₂O₂ yield of 11.4 % at ?0.4 V. Meanwhile, the GMM35 nanocomposite exhibits the same durability as commercial 20 wt% Pt/C in alkaline condition, but it shows lower peak power density (192.4 mW cm^?2 at 229.1 mA cm^?2) and cell voltage than those with a commercial Pt/C catalyst (260.9 mW cm^?2 at 285.4 mA cm^?2).     

Synthesis and Characterization of Polyvinylferrocene/Polypyrrole Composites

Conducting polymer composites of polyvinylferrocene and polypyrrole (PVF/PPy) were synthesized chemically by the in situ polymerization of pyrrole in the presence of PVF using FeCl₃ as oxidant. Acetic (CH₃COOH) and boric (H₃BO₃) acids were used as the synthesis medium. Effects of the synthesis medium on the properties of the PVF/PPy composite were investigated. The PVF/PPy composites and homopolymers were characterized by fourier transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS) and magnetic susceptibility techniques. Conductivity measurements were performed using the four‐probe technique. We found that the conductivities of PVF/PPy‐H₃BO₃ (1.19 S cm^?1) and PVF/PPy‐CH₃COOH (4.5×10^?1 S cm^?1) increased relative to those of the homopolymers of PPy‐H₃BO₃ (2.1×10^?2 S cm^?1) and PPy‐CH₃COOH (1.2×10^?2 S cm^?1) due to the interaction of PVF with the pyrrole moiety. The stability of all homopolymers and composites were investigated by thermogravimetric analysis and by conductivity measurements during heating‐cooling cycles. There was a small drop in conductivity caused by the annealing of PVF/PPy composites at 70°C. The conductivity of all samples increased with temperature and exhibited stable electrical behavior with increasing temperature. TGA analysis of samples showed that the composites were more stable than the homopolymers or PVF separately. The magnetic susceptibility values of samples were negative, except for PVF/PPy‐H₃BO₃. Morphology changes of the composites investigated by scanning electron microscopy (SEM), attributed to synthesis conditions, have a significant effect on their conductivity.     

Highly sensitive uric acid biosensor based on individual zinc oxide micro/nanowires

We describe the use of individual zinc oxide (ZnO) micro/nanowires in an electrochemical biosensor for uric acid. The wires were synthesized by chemical vapor deposition and possess uniform morphology and high crystallinity as revealed by scanning electron microscopy, X-ray diffraction, and photoluminescence studies. The enzyme uricase was then immobilized on the surface of the ZnO micro/nanowires by physical adsorption, and this was proven by Raman spectroscopy and fluorescence microscopy. The resulting uric acid biosensor undergoes fast electron transfer between the active site of the enzyme and the surface of the electrode. It displays high sensitivity (89.74 μA cm^?2 mM^?1) and a wide linear analytical range (between 0.1 mM and 0.59 mM concentrations of uric acid). This study also demonstrates the potential of the use of individual ZnO micro/nanowires for the construction of highly sensitive nano-sized biosensors.

Performance studies of electrolyte-supported solid oxide fuel cell with Ni–YSZ and Ni–TiO2–YSZ as anodes

Redox cycling of Ni-based anode induces cell degradation which limits the cell's lifetime during solid oxide fuel cell operation. In the present study, the redox testing of electrolyte-supported cells has been investigated with TiO₂-added NiO–YSZ anode matrix. Button cells were fabricated by die-pressing YSZ powder as electrolyte, and onto which NiO–YSZ or NiO–TiO₂–YSZ anode and LSM–YSZ composite cathode were painted. The electrochemical performance and stability have been evaluated by measuring current–voltage characteristics followed by impedance spectroscopy after each redox cycling. Anode matrices before and after cell operation have been characterized by X-ray diffraction (XRD), elemental dispersive X-ray (EDX), and scanning electron microscopy (SEM). During cell operation the peak power density decreases from 111 mW cm^?2 (239 mA cm^?2) to 84 mW cm^?2 (188 mA cm^?2) between 23 and 128 h with five redox cycles for cell having NiO–YSZ (40:60) anode. But for cell with NiO–TiO₂–YSZ (30:10:60), the anode peak power density was constant and stable around 85 mW cm^?2 (194 mA cm^?2) throughout the cell run of 130 h and five redox cycles. No loss in the open circuit voltage was observed. SEM and XRD studies of NiO–TiO₂–YSZ (30:10:60) anodes revealed formation of ZrTiO₄, which may be responsible for inhibition of Ni coarsening leading to stable cell performance.     

Synthesis of polypyrrole micro/nanofibers via a self-assembly process

Novel polypyrrole (PPy) micro/nanofibers were synthesized via a self-assembly process by using 4-hydroxy-3-[(4-sulfo-1-naphthalenyl) azo]-1-naphthalenesulfonic acid (Acid Red B) as dopant and ferric chloride (FeCl₃) as oxidant. Experimental conditions, including the concentration of the dopant, reaction temperature and stirring state have been investigated for their influences on the morphology of the synthesized PPy micro/nanofibers. The products were characterized by scanning electron microscopy, transmission electron microscopy and Fourier-transform infrared spectroscopy. The formation mechanism of micro/nanofibers was studied. It is believed that the micelles formed by the dopant and pyrrole monomer act as templates during the synthesis process. Two functions of aggregation and synthesis are proposed in the reaction system simultaneously, and the morphologies of micro/nanofibers are the co-operations of these two functions. The maximum conductivity value of the PPy micro/nanofibers was 8.56 S cm^?1     

Very sensitive differential pulse adsorptive stripping voltammetric determination of 4-nitrophenol at poly (diphenylamine)/multi-walled carbon nanotube-β-cyclodextrin-modified glassy carbon electrode

In this work, a glassy carbon electrode (GCE) modified with poly (diphenylamine)/multi-walled carbon nanotubes-β-cyclodextrin (PDPA/MWCNT-β-CD) film was constructed and used for the determination of 4-nitrophenol (4-NP). Diphenylamine was successfully electropolymerised onto MWCNT-β-CD-modified GCE by cyclic voltammetry in monomer solution and 5 mol L^?1 H₂SO₄. The surface morphology of PDPA/MWCNT-β-CD film was characterised using scanning electron microscopy and electrochemical impedance spectroscopy. After adsorption of 4-NP on PDPA/MWCNT-β-CD at 0.2 V for 150 s, it showed a well-defined reduction peak in phosphate buffer solution at pH = 7. The PDPA/MWCNT-β-CD film enhanced the reduction peak current due to the complex formation between β-CD and 4-NP, presence of conductive polymer film as electron transfer mediator and also ability of MWCNTs for strong adsorptive and catalytic effect. Peak current increased linearly with 4-NP concentration in the range of 0.1 to 13.9 µg L^?1. The detection limit was obtained as 0.02 µg L^?1, which is better than other reported detection limits for the determination of 4-NP. The results showed that modified electrode has good sensitivity and selectivity. This sensor was used for the determination of 4-NP in water samples.     

Synthesis and characterization of Ti(IV)-substituted calcium hydroxyapatite particles by forced hydrolysis of Ca(OH)2-Na5P3O10-TiCl4 mixed solution

Ti(IV)-substituted calcium hydroxyapatite (TiHap) particles were prepared by aging Ca(OH)₂, TiCl₄, and sodium triphosphate (sodium tripolyphosphate, Natpp: Na₅P₃O₁₀) mixed solution at 100 °C for 18 h. The ellipsoidal secondary TiHap particles with ca. 100～150 nm in length composing by aggregation of small ellipsoidal primary particles with ca. 20 nm in length were produced at atomic ratio of Ti/(Ca+Ti) [X_Ti]≦0.2. The in situ IR spectra of these TiHap particles exhibited very small bulk OH^? band at 3,570 cm^?1. This result indicated that the TiHap particles were formed by aggregation of fine primary particles and OH^? ions along with c-axis in the primary particles were disordered. The TiHap particles with Ca/P atomic ratio larger than theoretical value of 1.67 did not exhibit surface P–OH groups at 3,659 and 3,682 cm^?1. The diffuse reflectance UV spectra of TiHap particles revealed that these particles have a UV absorption property, especially fabricated at X_Ti?=?0.1. The particles prepared at X_Ti?=?0.6 and 0.8 were amorphous and nanoparticles with 5～10 nm in diameter, but those precipitated at X_Ti?=?1.0 were poorly crystallized anataze-type TiO₂ nanoparticles.