固相微萃取-气相色谱质谱法联用测定水体中痕量多环麝香类化合物

采用固相微萃取-气相色谱质谱法联用测定了水体中痕量多环麝香类化合物。对固相微萃取条件和解析条件进行了优化,确定了微萃取条件为:选用65μmPDMS-DVB萃取头、顶空萃取模式(HS),在800 r/min,60℃条件下,萃取45 min;萃取过程中保持pH 7并且不加入NaCl;解析条件为:解析时间为3 min,插入GC深度为4 cm,进样口温度为250℃。方法的检测限为0.29～0.37 ng/L,线性范围5～1000ng/L,相对标准偏差1.5%～2.2%。对实际污水厂不同类型的水样使用优化后的实验条件进行了验证试验,目标化合物的回收率在82.5%～92.8%之间,表明优化后的试验条件适用于实际水体中痕量多环麝香类化合物的分析测定。     

Optimization of solid-phase microextraction for the gas chromatographic-mass spectrometric determination of synthetic musk fragrances in water samples

Described is a solid-phase microextraction-gas chromatography-mass spectrometric procedure for the determination of three polycyclic musk fragrances (galaxolide, tonalide, celestolide) and a nitro musk fragrance (musk ketone) in natural river water. Both classes of the musk fragrances could be extracted reproducibly from water samples with a recovery in the range of 45-50% and relative standard deviation of 11-18% for fragrances at 25-260 ng/l levels. Detection limits were between 14 and 22 ng/l. To achieve this reproducibility it was necessary to use an internal standard, pentachloronitrobenzene, for all substances. Best recoveries were achieved with polydimethylsiloxane (PDMS)-divinylbenzene fibers (compared to recoveries obtained with PDMS, polyacrylate or carboxen fibers) and extraction times of 45 min at 30 degrees C, with no need for attainment of equilibrium conditions. The latter was achieved at about 2 h. For Elbe River water, in the vicinity of Magdeburg, no matrix effects were observed. While the average levels of celestolide and musk ketone for samples investigated were below the detection limits, 14 and 22 ng/l, respectively, and for tonalide below the limit of quantification, 22 ng/l, the ambient levels of galaxolide in the Elbe River were 117 ng/l.     

Optimisation of headspace solid-phase microextraction for analysis of aromatic compounds in vinegar

Headspace solid-phase microextraction has been applied to the analysis of aroma compounds in vinegar. Silica fibre coated with Carboxen-polydimethylsiloxane was found to be more efficient at extracting these compounds than other fibres such as those coated with polydimethylsiloxane, Carbowax-divinylbenzene, and polydimethylsiloxane-divinylbenzene, but its repeatability was low. Different parameters such as extraction time, temperature of the sample during the extraction, ionic strength, and sample volume were optimised using a two-level factorial design expanded further to a central composite design. This chemometric tool is very appropriate in screening experiments where the aim is to investigate several possibly influential and/or interacting factors. The extraction efficiency is inversely affected by the acetic acid content-an increase in the acetic acid concentration decreases the extraction efficiency. No interference is observed with the increase in content of polyphenols.     

Optimisation of a solid-phase microextraction method for the analysis of nicotine in hair

A headspace solid-phase microextraction method (HS-SPME) followed by gas chromatography with mass spectrometric detection (GC/MS) has been developed for the determination of low concentrations of nicotine in hair. Parameters affecting the SPME procedure including type of fiber coating, extraction mode, extraction temperature and time, desorption time, stirring, and salt addition have been evaluated and optimised. The method provided good linearity (r(2)≥0.9980) over the concentration range tested (0.2-20 ng/mg) and low detection limit (0.02 ng/mg). Precision expressed as relative standard deviation was <10%. The average accuracy was 95%. The proposed method was used to determine hair nicotine levels in 100 children in order to assess exposure to environmental tobacco smoke (ETS). The described HS-SPME procedure is fast, simple, sensitive, and solvent-free and is therefore suitable for studies involving ETS exposure assessment.     

Determination of musk compounds in sewage treatment plant sludge samples by solid-phase microextraction

Headspace solid-phase microextraction, followed by GC-MS analysis is presented as a suitable technique for the determination of musk compounds in sewage treatment plant sludge. Five polycyclic musks (celestolide, phantolide, traseolide, galaxolide and tonalide) and four nitro musks (musk xylene, musk moskene, musk tibetene and musk ketone) were considered in the optimisation of the analytical method. The influence of extraction temperature, fibre coating, agitation, pH and salting out on the efficiency of the extraction along with the extraction kinetics were studied. An extraction temperature of 100 degrees C and sampling the headspace over the stirred sludge sample using polydimethylsiloxane -divinylbenzene as fibre coating lead to effective extraction. The method proposed is very simple and yields high sensitivity, good linearity and repeatability for all the analytes with limits of detection at the sub-ng/g level. The total analysis time, including extraction and GC analysis, was only 40 min, and no manipulation of the sample was required.     

Optimisation of solid-phase microextraction of volatiles

The results of a systematic study on the precision and repeatability of measurements of the headspace solid phase micro-extraction (SPME) with open-cap vials in combination with capillary gas chromatography in comparison with septum-sealed vials are reported. Benzene, toluene, ethylbenzene, and xylene isomers (BTEX) were used as the target analytes in the investigation of spiked water samples at concentration levels of 42.5 μg l⁻¹. The dependence of a sample volume versus peak area showed maximum SPME recovery. The influence of sample volume on the precision and the time of taking the sample on the losses of volatile analytes was examined.     

Optimisation of alachlor solid-phase microextraction from water samples using experimental design

We have tested screening and response surface experimental designs to optimise the solid-phase microextraction (SPME) of the widely used herbicide alachlor. Extraction time and sample volume were the only statistically significant factors from those studied. In the final optimised conditions the procedure was applied to the SPME-HPLC analysis of alachlor in spiked water samples with excellent figures of merit.     

Optimisation and validation of a solid-phase microextraction method for simultaneous determination of different types of pesticides in water by gas chromatography-mass spectrometry

A solid-phase microextraction (SPME) method for the simultaneous determination of a large number of pesticides (46) with a wide range of polarities and chemical structures (organochlorine, organophosphorous, triazines, pyrethroids and others) in water samples by GC-MS has been developed. Three different fibres and parameters that influence the extraction and desorption efficiency were studied. The selected conditions were: a 60 microm polydimethylsiloxane/divinylbenzene (PDMS/DVB) fibre, 45 min of extraction time, sample agitation and temperature control at 60 degrees C; neither pH adjustment nor ionic strength correction were applied. Good detection limits, linearity and repeatability were obtained with this method for the 46 pesticides studied. The method was validated for 29 pesticides following the recommendations of the international norm ISO/IEC 17025 including the calculation of the uncertainties. The detection limits ranged from 4 to 17 ng l(-1). Furthermore, repeatability (6.9-20.5%) and intermediate precision (4.5-19.7%) were shown to be satisfactory. To validate matrix effects for drinking and surface water analytical recoveries were calculated for these matrices. The accuracy of the method was also evaluated by participating in a proficiency inter-laboratory test.     

Development of a solid-phase microextraction method with micellar desorption for the determination of chlorophenols in water samples. Comparison with conventional solid-phase microextraction method

A novel analytical method is presented for the determination of chlorophenols in water. This method involves pre-concentration by solid-phase microextraction (SPME) and an external desorption using a micellar medium as desorbing agent. Final analysis of the selected chlorophenols compounds was carried out by high-performance liquid chromatography (HPLC) with diode array detection (DAD). Optimum conditions for desorption, using the non-ionic surfactant polyoxyethylene 10 lauryl ether (POLE), such as surfactant concentration and time were studied. A satisfactory reproducibility for the extraction of target compounds, between 6 and 15%, was obtained, and detection limits were in the range of 1.1-5.9ngmL(-1). The developed method is evaluated and compared with the conventional one using organic solvent as a desorbing agent. The method was successfully applied to the determination of chlorophenols in water samples from different origin. This study has demonstrated that solid-phase microextraction with micellar desorption (SPME-MD) can be used as an alternative to conventional SPME method for the extraction of chlorophenols in water samples.     

Optimisation of a matrix solid-phase dispersion method for the determination of organophosphate compounds in dust samples

A fast and inexpensive sample preparation procedure based on the matrix solid-phase dispersion (MSPD) technique is proposed for the isolation of several organophosphate esters (mainly employed as flame retardants and plasticizers) from indoor dust samples. Extraction and clean-up were carried out in a single step and target compounds were determined by gas chromatography (GC) with nitrogen-phosphorus detection (NPD). The main parameters affecting extraction yield and selectivity, such as type and amount of dispersant material, clean-up co-sorbent and extraction solvent, were evaluated and optimised. Under final conditions, 0.5 g of dust were dispersed with equal amounts of anhydrous sodium sulphate and Florisil, and loaded on the top of a polypropylene cartridge containing 0.5 g of alumina. The dispersed sample was washed with 2 mL of n-hexane to remove the least polar interferences and analytes were eluted with 3 mL of acetone. Recoveries of the proposed method for spiked samples ranged from 80 to 116%, and the day-to-day variability remained between 5 and 10%. Data on levels of organophosphate species in dust from private houses and vehicle cabins are provided. In both cases, the lowest concentrations corresponded to the short chain, non-chlorinated, alkyl organophosphates, whereas mean values above 1 μg g⁻¹ were measured for the rest of analytes.     

An evaluation of solid-phase microextraction for analysis of volatile organic compounds in drinking water

Solid-phase microextraction (SPME) has been applied to the quantitative analysis of 60 volatile organic compounds (VOCs) in drinking water. Equilibration curves for the partitioning of the VOCs between the fiber coating and fortified water obtained at 20, 50, and 80 °C are found between the theoretical curves for completely agitated and non-agitated samples. Two important factors for the amount adsorbed by the SPME fiber coating are the extraction time and the fiber coating/water distribution coefficient, K_FW . Both depend on the sample temperature, but in a counteracting manner: Increasing the temperature shortened the equilibration times, especially for the heavier VOCs, but also lead to lower K_FW values, and consequently a lower sensitivity of the method. K_FW values are determined for 33 of the VOCs at 40, 60, and 80°C and the heats of adsorption,–ΔH, are calculated. The nature of the adsorption is found to be exothermic which explains the decreasing sensitivity of the method with increasing temperature. Detection limits were typically from 20 ng/l to 200 ng/l, except for the very light VOCs with which detection difficulties were encountered. For all of the VOCs the linear range extended from the lowest concentration at which they were actually detected to at least 5 mg/l. The precision, 3% average standard deviation when an internal standard was used, was satisfactory for most quantitative routine analysis. SPME was also applied to head-space (HS) analysis of drinking water through the coupled equilibrium between water/head-space/fiber coating. HS-SPME is demonstrated to have shorter equilibration times than SPME directly from the water and equal sensitivities, except for the very light VOCs. Water samples from a drinking water plant contaminated in the low μg/l range with 1,1,1-trichloroethane, trichloroethene and tetrachloroethene were analyzed. There seems to be a reasonable agreement between results obtained by SPME and purge & trap. It is concluded that SPME has a great potential for drinking water analysis.     

Development of a solid-phase microextraction method for determination of volatile oxidation compounds in fish oil emulsions

Headspace solid-phase microextraction (HS-SPME) is proposed for isolating and determining the headspace volatiles formed during oxidation of fish-oil-in-water emulsions. Three different fiber coatings were tested and compared for sensitivity and reproducibility. A carboxen/polydimethylsiloxane (CAR-PDMS) fiber coating was found to be the most suitable for the analysis of emulsion volatiles. The main factors affecting the microextraction process on CAR-PDMS were then evaluated by a factorial design: amount of sample, time and temperature of extraction and stirring. The incubation of 0.5 g of emulsion at 60 degrees C during 30 min leads to the most effective extraction of volatiles associated with lipid oxidation of fish oil emulsions. The HS-SPME method coupled with GC-MS allowed the qualitative and quantitative analysis of the volatiles derived from oxidation of real fish oil enriched foods such as milk and mayonnaise. The method here proposed is very fast and simple and yields high sensitivity, with good repeatability for all target compounds.     

Development of a solid-phase microextraction method for the determination of phthalic acid esters in water

Solid-phase microextraction method (SPME) coupled to GC/ECD has been developed and validated for the determination of phthalic acid esters (dimethyl-, diethyl-, di-n-butyl-, butylbenzyl-, di-2-ethylhexyl- and di-n-octyl phthalate) in water samples. Two types of coatings (PDMS, PA), altogether four different kinds of fibers have been investigated. Both parameters affecting the partition of analytes between a fiber coating and aqueous phase (i.e. extraction time, extraction temperature, agitation) and conditions of the thermal desorption in a GC injector were optimized. The final SPME method employing the polyacrylate fiber, extraction time 20 min, heating and stirring of the sample enabled the determination of all six phthalates in water samples. The method showed linear response over four orders of magnitude and the limits of quantification of the method ranged between 0.001 and 0.050 μg l⁻¹. The repeatability expressed as R.S.D. was in the range 4-10% for the spiking level 7 μg l⁻¹ of each analyte. The applicability of the developed SPME method was demonstrated for real water samples.     

Optimisation of a simple and reliable method based on headspace solid-phase microextraction for the determination of volatile phenols in beer

A simple, accurate and sensitive method based on headspace solid-phase microextraction (HS-SPME) coupled to gas chromatography–tandem mass spectrometry (GC–MS/MS) was developed for the analysis of 4-ethylguaiacol, 4-ethylphenol, 4-vinylguaiacol and 4-vinylphenol in beer. The effect of the presence of CO₂ in the sample on the extraction of analytes was examined. The influence on extraction efficiency of different fibre coatings, of salt addition and stirring was also evaluated. Divinylbenzene/carboxen/polydimethylsiloxane was selected as extraction fibre and was used to evaluate the influence of exposure time, extraction temperature and sample volume/total volume ratio (V_s/V_t) by means of a central composite design (CCD). The optimal conditions identified were 80 °C for extraction temperature, 55 min for extraction time and 6 mL of beer (V_s/V_t 0.30). Under optimal conditions, the proposed method showed satisfactory linearity (correlation coefficients between 0.993 and 0.999), precision (between 6.3% and 9.7%) and detection limits (lower than those previously reported for volatile phenols in beers). The method was applied successfully to the analysis of beer samples. To our knowledge, this is the first time that a HS-SPME based method has been developed to determine simultaneously these four volatile phenols in beers.     

Optimisation of a headspace solid-phase microextraction with on-fiber derivatisation method for the direct determination of haloanisoles and halophenols in wine

A solid-phase microextraction (SPME) procedure for the determination of four haloanisoles (2,4,6-trichloroanisole, 2,3,4,6-tetrachloroanisole, pentachloroanisole and 2,4,6-tribromoanisole), as well as their precursor halophenols (2,4,6-trichlorophenol, 2,3,4,6-tetrachlorophenol, pentachlorophenol and 2,4,6-tribromophenol), involved in the presence of cork taint in wine, was developed. Firstly, analytes were concentrated on a SPME fiber, and then halophenols were derivatised using N-methyl-N-trimethylsilyltrifluoroacetamide (MSTFA). The compounds were desorbed for 5 min in the gas chromatography injector port and then determined with an electron capture detector. The influence of different parameters on the efficiency of extraction (volume of sample, type of fibre coating and time) and derivatisation (time, temperature and volume of MSTFA) steps was evaluated. Polyacrylate (PA) was selected as the extraction fiber, optimised parameters for SPME were 10 ml of wine, temperature 70 degrees C and extraction time 60 min. The optimal conditions identified for the derivatisation step were temperature 25 degrees C, reagent volume 50 microl and extraction time 25 min. Under optimal conditions, the proposed method showed satisfactory linearity, precision and detection limits. The method was applied successfully to the analysis of red wine samples. To our knowledge, this is the first time that headspace (HS) SPME combined with on-fiber derivatisation has been applied to determine cork taint responsible compounds in wine.     

Optimisation of headspace solid-phase microextraction for the analysis of volatile phenols in wine

Headspace solid-phase microextraction has been applied to the analysis of volatile phenols in wine. Silica fibre coated with Carbowax-divinylbenzene was found to be more efficient at extracting these compounds than other fibres such as those coated with polydimethylsiloxane, polyacrylate, carboxen-polydimethylsiloxane, and polydimethylsiloxane-divinylbenzene. Different parameters such as extraction time, temperature of the sample during the extraction, ionic strength and sample volume were optimised using a two-level factorial design expanded further to a central composite design, in order to evaluate several possibly influential and/or interacting factors. The headspace (HS)-SPME procedure developed shows adequate detection and quantitation limits, and linear ranges for correctly analysing these compounds in wine. The recoveries obtained were close to 100%, with repeatability values lower than 16%. The method was applied to a variety of white and red wines.     

Development of a solid-phase microextraction method for the analysis of phenolic flame retardants in water samples

A solid-phase microextraction (SPME) method for the ultra-trace determination of brominated phenols in aqueous samples has been developed and is reported for the first time to the best of our knowledge. 3,5,3',5'-tetrabromobisphenol A (TBBPA), the most widely used brominated flame retardant, and other phenolic flame retardants in commercial use, such as 2,4-dibromophenol (2,4-DBP), 2,4,6-tribromophenol (TBP) and pentabromophenol (PBP) have been included as target analytes. The analytical procedure involves the in situ acetylation-SPME and gas chromatography-mass spectrometry (GC-MS) determination of the target analytes. A multi-factor categorical experimental design was created to study the main parameters affecting the extraction efficiency, allowing also the evaluation of interaction effects between factors. The factors studied were type of fiber, extraction mode, exposing the fiber directly into the sample (DSPME) or into the headspace over the sample (HSSPME), and extraction temperature. Carboxen-polydimethylsiloxane (CAR-PDMS) fiber appeared to be the most suitable of the five fibers tested for the extraction of most compounds, excluding PBP and TBBPA for which polydimethylsiloxane (PDMS) was the most efficient coating. The highest response was achieved for both fibers sampling in headspace mode at 100 degrees C. In order to test the linearity of the method, calibration studies were performed with both CAR-PDMS and PDMS coatings. For both fibers, the method was linear in a range of 2 orders of magnitude, giving relative standard deviation (RSD%) below 10% for most compounds and detection limits at the low pg/mL level. In addition, the feasibility of the method for simultaneous determination of chlorinated and brominated phenols was studied. Finally, the method was applied to several real samples including tap water and effluent and influent waste water samples from an urban treatment plant, in which several phenolic compounds, such as phenol, methylphenols and chlorophenols, could be detected and quantified.     

Study of the photoinduced degradation of polycyclic musk compounds by solid-phase microextraction and gas chromatography/mass spectrometry

Polycyclic musks are widely used synthetic fragrances that have been identified during the last few years in biota samples and environmental matrices. Nevertheless, there is a lack of information concerning the photodegradation behavior of these compounds. In this work, the photoinduced degradation of six polycyclic musk compounds (Cashmeran, Celestolide, Phantolide, Galaxolide, Traseolide and Tonalide) was studied using a solid-phase microextraction (SPME) fiber as support. Musk fragrances were extracted from aqueous solutions using SPME fibers that were subsequently exposed to ultraviolet (UV) irradiation for different times. To study the degradation kinetics and to tentatively identify the photoproducts generated, gas chromatography coupled to ion trap mass spectrometry was used. Aqueous photodegradation studies were also performed. The on-fiber photodegradation approach avoids the need for further extraction processes and makes the identification of photoproducts easier, due to their higher concentration on the fibers. All musk compounds were easily photodegraded, suggesting that UV irradiation could work as a decontamination tool for these musks.     

Development and validation of a solid-phase microextraction method for the analysis of volatile organic compounds in groundwater samples

Summary Solid-phase microextraction is a relatively recent extraction technique for sample preparation. It has been used successfully to analyse environmental pollutants in a variety of matrices such as soils, water and air. In this work, a simple and rapid method for the analysis of volatile organic and polar compounds from polluted groundwater samples by SPME coupled with gas chromatography (GC) is described. Different types of fibres were studied and the extraction process was optimised. The fibre that proved to be the best to analyse this kind of samples was CAR-PDMS. The method was validated by analysis of synthetic samples and comparison with headspace—GC. The optimised method was successfully applied to the analysis of ground-water samples.     

Optimisation of derivatisation for the analysis of estrogenic compounds in water by solid-phase extraction gas chromatography-mass spectrometry

An optimisation of derivatisation methods for the simultaneous determination of endocrine disrupting chemicals (EDCs) in water by solid-phase extraction (SPE) gas chromatography-mass spectrometry (GC-MS) was developed in this study. Seven highly potent EDCs including 17β-estradiol (E2), estrone (E1), 16α-hydroxyestrone, 17α-ethynylestradiol (EE2), bisphenol A, 4-nonylphenol and 4-tert-octylphenol were selected as the target compounds. The SPE technique, followed by the derivatisation with N,O-bis(trimethylsilyl)trifluoroacetamide (BSTFA) was used for the extraction recoveries of compounds from water and effluent samples. The stability of the silylation derivatives under different reaction conditions was investigated. The combined use of BSTFA and pyridine as derivatisation reagents, together with the use of hexane as the final solvent, was preferred in order to generate more stable derivatives of EDCs. The relative response factor (RRF) of all derivatives except that of EE2 was stable 120 h after derivatisation. The addition of pyridine as derivatisation reagent with BSTFA can prevent the conversion of EE2 to other products during the reaction. Several parameters that may affect the recovery of EDCs, such as the SPE flow rate, and water properties including aquatic colloid content and surfactant concentration were tested. The results showed that the flow rate (1-25 mL min⁻¹), colloid concentration (0-50 mg L⁻¹) and surfactants concentration (0-10 μg L⁻¹) did not cause significant decrease in the EDCs recovery.