BaWO4纳米线束的合成及其光学性质研究

High quality BaWO₄ nanowire bundles have been synthesized in toluene-sodium dodecylbenzene sulphonate (SDBS)-small amount PEG20000-H₂O reverse micelle system. XRD result shows that the obtained BaWO₄ belongs to tetragonal phase with scheelite structure. TEM results demonstrate that the obtained BaWO₄ nanowire bundles have high aspect-ratio (>650). The experimental results confirm that PEG20000 plays a key role for the formation of BaWO₄ nanowire bundles. Other factors which influence the morphology and crystallinity of the product are also briefly discussed. Moreover， the obtained BaWO₄ nanowire bundles exhibit strong photoluminescence centered at 397.3 nm with λ_ex=343.5 nm at room temperature， which is different from the bulk BaWO₄ crystals.     

Single‐Crystalline ZnO Nanowire Bundles: Synthesis,Mechanism and Their Application in Dielectric Composites

Single‐crystalline ZnO nanowire bundles have been synthesized in large‐scale by an improved microemulsion method in the presence of excessive hydrate hydrazine and dodecyl benzene sulfonic acid sodium salt (DBS) in xylene. The product is characterized using X‐ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and high‐resolution transmission electron microscopy (HRTEM). The result shows that the bundle is composed by many oriented single‐crystalline ZnO nanowires with a length of about 1 μm and a diameter of about 20–30 nm. The influence of DBS, hydrazine and the reaction time on the morphology of final product and the formation mechanism of such nanostructures were discussed; the application in the dielectric composites is also studied.     

Solution-grown zinc oxide nanowires

We review two strategies for growing ZnO nanowires from zinc salts in aqueous and organic solvents. Wire arrays with diameters in the nanoscale regime can be grown in an aqueous solution of zinc nitrate and hexamethylenetetramine. With the addition of poly(ethylenimine), the lengths of the wires have been increased to 25 mum with aspect ratios over 125. Additionally, these arrays were made vertical by nucleating the wires from oriented ZnO nanocrystals. ZnO nanowire bundles have been produced by decomposing zinc acetate in trioctylamine. By the addition of a metal salt to the solution, the ZnO wires can be doped with a range of transition metals. Specifically, ZnO nanowires were homogeneously doped with cobalt and showed a marked deviation from paramagnetic behavior. We conclude by highlighting the use of these solution-grown nanowire arrays in dye-sensitized solar cells. The nanowire cells showed an improvement in the charge collection efficiency over traditional nanoparticle cells.     

ZnO纳米线阵列的电沉积法制备及表征(英文)

利用直流电沉积方法在多孔氧化铝模板的孔洞中生成锌纳米线,在氧气氛围中,于800°C下氧化2h,将氧化铝中的锌氧化成氧化锌.本研究利用氧气氛围进行锌的氧化,大大提高了传统方法的氧化锌纳米线的制备效率.用场发射扫描电子显微镜(FE-SEM)、透射电子显微镜(TEM)和X射线衍射仪(XRD)对其形貌及成分进行表征和分析,结果表明,氧化铝模板的有序孔洞中填充了大尺寸、均匀连续的多晶态氧化锌纳米线.纳米线具有约1000:1的高纵横比,其长度等于氧化铝模板的厚度,直径约为80nm.光致发光(PL)光谱表明,氧化锌纳米线在504nm处有由于氧空位引起的较强蓝绿光发射.这为进一步研究ZnO/AAO组装体发学性质和开发新型功能器件提供了基础.     

Synthesis and Characterization of ZnO Nanowires

Zinc oxide is a wide bandgap (3.37 eV) semiconductor with a hexagonal wurtzite crystal structure. ZnO prepared in nanowire form may be used as a nanosized ultraviolet light-emitting source. In this study, ZnO nanowires were prepared by vapor-phase transport of Zn vapor onto gold-coated silicon substrates in a tube furnace heated to 900 ?C. Gold serves as a catalyst to capture Zn vapor during nanowire growth. Size control of ZnO nanowires has been achieved by varying the gold film thickness…     

Dendritic nanowire ultraviolet laser array

Self-organized dendritic crystal growth is explored to assemble uniform semiconductor nanowires into highly ordered one-dimensional microscale arrays that resemble comb structures. The individual ZnO nanowires have uniform diameters ranging from 10 to 300 nm. They are evenly spaced on a stem with a regular periodicity of 0.1-2 micrometer. Under optical excitation, each individual ZnO nanowire serves as a Fabry-Perot optical cavity, and together they form a highly ordered nanowire ultraviolet laser array.     

Precursor-induced hydrothermal synthesis of flowerlike cupped-end microrod bundles of ZnO

Flowerlike cupped-end ZnO microrod bundles have been hydrothermally synthesized from precursor ZnCl2(N2H4)2 in sheet shape at 140 degrees C for 12 h; under the same conditions using the same precursor in rod shape, uniform ZnO nanorods were obtained. XRD pattern indicated the sample is ZnO with hexagonal cell contants a = 3.251 A and c = 5.206 A. FE-SEM and TEM show the formation process of the ZnO sample. HRTEM revealed that the flowerlike cupped-end ZnO microrod bundles grow along the [101] axis. The UV emission peak at approximately 396 nm and the blue band emission peak at approximately 469 nm were observed by PL spectra. A possible formation mechanism was proposed.     

取向Zn1-xMgxO纳米线阵列的制备及光学特性

采用化学气相沉积(CVD)法, 以高纯ZnO、Mg和活性C混合粉末为原料, 在Si(111)衬底上制备了不同配比的取向Zn1-xMgxO纳米线阵列. 用X射线衍射仪(XRD), 扫描电镜(SEM), 能量色散X射线分析(EDAX)及光致发光(PL)光谱分析仪对样品的晶体结构、形貌、成分组成和光致发光特性进行了分析. 用霍尔效应测量系统测试了不同配比样品的载流子浓度. 实验发现, 当Zn1-xMgxO纳米线阵列中Mg原子相对Zn原子摩尔比x值较小时(x<0.29), XRD衍射谱中只有ZnO晶体标准衍射峰, 没有MgO晶体衍射峰, 说明此时制备的Zn1-xMgxO纳米线样品晶格结构以ZnO纤锌矿结构为主, Mg原子只是作为替位或填隙原子分布在ZnO晶体中. 但当样品中x>0.53时, ZnO与MgO的特征衍射峰同时出现在样品的衍射谱图中, 说明随原料中Mg原子摩尔比的增加, 制备的Zn1-xMgxO纳米阵列样品中ZnO纤锌矿结构与MgO岩盐结构同时存在, 样品呈现多晶体结构形式. 实验还对比了制备的纯ZnO与不同配比的Zn1-xMgxO纳米线阵列的光致发光光谱和载流子浓度, 发现随Mg含量的增加, Zn1-xMgxO阵列紫光发光峰出现了较明显的蓝移现象, 同时, 测试结果也表明, 随Mg含量的增加, Zn1-xMgxO阵列的紫光和绿光峰发光强度都有所减弱, 样品的载流子浓度也随之下降. 文章对实验结果进行了分析和探讨.     

Synthesis and optical properties of S-doped ZnO nanostructures: nanonails and nanowires

S-doped ZnO nanostructures such as nanonails and nanowires have been synthesized via a simple one-step catalyst-free thermal evaporation process on a large scale. The doping concentration of sulfur into ZnO nanonails and nanowire were 2 atm % and 7.5 atm %, respectively. Studies found that the S-doped ZnO nanonails and nanowires were single-crystalline wurtzite structure and grew along the (001) direction. The average diameters of the nanonails and nanowires were 70 and 50 nm, respectively. Low-temperature photoluminescence spectra of ZnO samples showed two luminescence peaks in the UV and green emission region, respectively. As the concentration of sulfur in the ZnO nanostructures increased, the intensity of the UV emission peak decreased dramatically, and it showed a little blue-shift while the intensity of the green emission increased greatly.     

Novel ZnO nanostructured electrodes for higher power conversion efficiencies in polymeric solar cells

1-Dimensional nanostructured ZnO electrodes have been demonstrated to be potentially interesting for their application in solar cells. Herein, we present a novel procedure to control the ZnO nanowire optoelectronic properties by means of surface modification. The nanowire surface is functionalized with ZnO nanoparticles in order to provide an improved contact to the photoactive P3HT:PCBM film that enhances the overall power conversion efficiency of the resulting solar cell. Charge extraction and transient photovoltage measurements have been used to successfully demonstrate that the surface modified nanostructured electrode contributes in enhancing the exciton dissociating ratio and in enlarging the charge lifetime as a consequence of a reduced charge recombination. Under AM1.5G illumination, all these factors contribute to a considerably large increase in photocurrent yielding unusually high conversion efficiencies over 4% and external quantum efficiencies of 87% at 550 nm for commercially available P3HT:PCBM based solar cells. The same approach might be equally used for polymeric materials under development to overcome the record reported efficiencies.     

High-aspect-ratio aluminum borate nanowire bundles supported by sucrose

High-aspect-ratio and single-crystal aluminum borate (Al(18)B(4)O(33)) nanowire bundles with an ordered orientation were synthesized by using an innovative sucrose-assisted growth process. The process involves the dehydration and polycondensation of aluminum borate-sucrose solution to form a highly viscous precursor. The sucrose plays a crucial role in the growth of the nanowire bundles by supporting as a polymeric substrate and a type of adhesive template. Electron microscopy was used to characterize the high-aspect-ratio nanowire bundles. A possible growth mechanism for the nanowire bundles is proposed.     

Effects of ZnO nanowire length on surface-assisted laser desorption/ionization of small molecules

The effects of nanowire (NW) length on surface-assisted laser desorption/ionization (SALDI) mass spectrometry (MS) of small molecules were investigated using ZnO NWs of 50 nm diameter with a broad range of lengths ranging from 25 to 1600 nm. Characterization of the ZnO NWs revealed that the length was the only parameter that varied in this study, while other properties of the NWs remained essentially the same as the bulk properties. Experiments on SALDI efficiency exhibited that the SALDI processes on NWs have a certain length window. In the present case of ZnO NWs, the SALDI efficiency was found to be enhanced on the nanowires of 250 nm length, corresponding to an aspect ratio of 5. The roles of NW length in the SALDI processes were discussed from the viewpoint of efficient energy-transfer media as well as physical obstacles screening laser irradiation and preventing the escape of nascent ions from NW surfaces. The existence of the length window may provide valuable insight for tailoring new nanostructures for efficient SALDI of small molecules.     

ZnO纳米线形态对其光致发光性能的影响

以多孔氧化铝膜为模板,电化学沉积出Zn纳米线,再通过高温氧化得到ZnO纳米线阵列。通过改变制备多孔氧化铝模板的工艺参数来改变模板纳米孔径,进而改变ZnO纳米线的直径,得到不同形态的ZnO纳米线阵列。应用X射线衍射仪、透射电子显微镜测试技术表征了ZnO纳米线的结构与形貌。结果发现,X射线衍射时会出现随ZnO纳米线直径增大衍射峰增多和增强的现象。采用荧光光谱仪测试样品的光致发光性能,通过Gaussian原理对谱峰的拟合分析了ZnO纳米线形态对其光致发光光谱的影响。结果表明,随着纳米线直径从30nm至60nm依次增大,其结晶性和化学计量比逐渐变好。近紫外区和蓝光区的发射峰随着纳米线直径的增大而蓝移,而纳米线直径为60nm的样品则出现随直径增大而红移的现象。结果可见,直径在55~60nm间的某点将是ZnO纳米线的结构和光致发光性能变化的临界点。     

Carbon-decorated ZnO nanowire array: A novel platform for direct electrochemistry of enzymes and biosensing applications

We report here the direct electron transfer of GOD and a novel glucose biosensor based on carbon-decorated ZnO(C–ZnO) nanowire array electrode. The C–ZnO nanowire array provides a novel platform for fast direct electrochemistry of GOD, and its based biosensor shows very high sensitivity and low detection limit. Based on the direct electrochemistry of horseradish peroxidase (HRP), the H₂O₂ biosensing application is further demonstrated using this new C–ZnO array architecture. The high conductivity of carbon and good electron transfer capability of ZnO nanowires, along with their low cost and biocompatibility make the C–ZnO nanowire array a promising platform for direct electrochemistry of enzymes and mediator-free enzymatic biosensors.     

Fe3O4-LiMo3Se3 nanoparticle clusters as superparamagnetic nanocompasses

A scaleable chemical approach to functional nanoscale analogues of the magnetic compasses in magnetotactic bacteria is described. LiMo(3)Se(3)-Fe(3)O(4) nanowire-nanoparticle composites were synthesized by a reaction of 3-iodopropionic acid treated LiMo(3)Se(3) nanowire bundles with oleic acid-stabilized Fe(3)O(4) nanoparticles of 2.8, 5.3, and 12.5 nm size in tetrahydrofuran. Transmission electron micrographs show that the composite consists of Fe(3)O(4) nanoparticles attached to the surfaces of the 4-6 nm thick nanowire bundles. UV/vis spectra reveal absorptions from the nanowire (506 nm) and magnetite components (280-450 nm), and IR spectra show characteristic bands for the propionic acid linkers and for the residual oleic acid ligands on the magnetite particles. In the presence of excess oleic acid, the nanocomposites undergo rapid disassembly, suggesting that Fe(3)O(4) nanoparticles are bonded to nanowires via carboxylate groups from the linkers. Ultrasonication of a dispersion of the composite in THF produces individual LiMo(3)Se(3)-Fe(3)O(4) clusters, which are 340 +/- 107 nm long and 20 +/- 5 nm thick, depending on the sonication time and Fe(3)O(4) nanoparticle size. Field cooled and zero-field cooled magnetization measurements reveal that the blocking temperature (T(B) = 100 K) of the clusters with 5.3 nm Fe(3)O(4) is increased as compared to the free nanoparticles (T(B) = 30 K). Directional dipolar interactions in the clusters lead to magnetic anisotropy, which makes it possible to align the clusters in a magnetic field (900 Oe).     

液相法制备取向ZnO纳米线阵列的场发射特性(英文)

采用水热合成工艺,在不同条件下制备了不同的一维取向ZnO纳米线阵列样品.用X射线衍射仪(XRD)、扫描电镜(SEM)及透射电镜(TEM)对样品的晶体结构和形貌等进行了表征,对样品的场发射特性进行了分析和比较,并用Fowler-Nordheim方程对影响ZnO纳米线场发射的因素进行了研究.结果表明,具有较低生长密度分布、较高的长径比和较尖锐生长端的ZnO纳米线阵列样品具有较好的场发射特性.     

ZnO-Al2O3 and ZnO-TiO2 core-shell nanowire dye-sensitized solar cells

We describe the construction and performance of dye-sensitized solar cells (DSCs) based on arrays of ZnO nanowires coated with thin shells of amorphous Al(2)O(3) or anatase TiO(2) by atomic layer deposition. We find that alumina shells of all thicknesses act as insulating barriers that improve cell open-circuit voltage (V(OC)) only at the expense of a larger decrease in short-circuit current density (J(SC)). However, titania shells 10-25 nm in thickness cause a dramatic increase in V(OC) and fill factor with little current falloff, resulting in a substantial improvement in overall conversion efficiency, up to 2.25% under 100 mW cm(-2) AM 1.5 simulated sunlight. The superior performance of the ZnO-TiO(2) core-shell nanowire cells is a result of a radial surface field within each nanowire that decreases the rate of recombination in these devices. In a related set of experiments, we have found that TiO(2) blocking layers deposited underneath the nanowire films yield cells with reduced efficiency, in contrast to the beneficial use of blocking layers in some TiO(2) nanoparticle cells. Raising the efficiency of our nanowire DSCs above 2.5% depends on achieving higher dye loadings through an increase in nanowire array surface area.     

Solution synthesis of large-scale, high-sensitivity ZnO/Si hierarchical nanoheterostructure photodetectors

This Communication reports a low-cost solution fabrication of wafer-scale ZnO/Si branched nanowire heterostructures and their high photodetection sensitivity, with an ON/OFF ratio larger than 250 and a peak photoresponsivity of 12.8 mA/W at 900 nm. This reported unique 3D branched nanowire structure offers a generic approach for the integration of new functional materials for photodetection and photovoltaic applications.     

Aqueous solution route to high-aspect-ratio zinc oxide nanostructures on indium tin oxide substrates

High-aspect-ratio ZnO nanowires and nanotubes are formed on indium tin oxide (ITO) substrates using a three-step route at low temperatures. The three steps, including successive ionic layer absorption and reaction (SILAR) deposition of the ZnO seed layer, hydrothermal annealing of the seed layer, and chemical bath deposition (CBD) of the one-dimensional (1D) ZnO nanostructures, are all conducted in aqueous solutions at temperatures below 120 degrees C. Both the hydrothermal annealing of the SILAR seed layer and the low-concentration precursor solution employed in the CBD process are crucial in order to synthesize the uniform and high-aspect-ratio ZnO nanostructures on the ITO substrate. TEM analyses reveal that both the nanowire and the nanotube possess the single-crystal structure and are grown along [001] direction. Room-temperature cathodoluminescence spectrum of the 1D ZnO nanostructures shows a sharp ultraviolet emission at 375 nm and a broad green-band emission.     

Solubility of Mo6S4.5I4.5 nanowires in common solvents: a sedimentation study

Due to their ease of fabrication and monodisperse, metallic nature, molybdenum-sulfur-iodine nanowires are an interesting alternative to carbon nanotubes for some applications. However very little is known about the solubility of these materials. In this work we have investigated the solubility of Mo(6)S(4.5)I(4.5) nanowire soot in a range of common solvents by performing sedimentation studies and microscopic and spectroscopic characterization. A sedimentation equation was derived showing that the concentration of any insoluble dispersed phase decreases exponentially with time. We find that in all solvents, Mo(6)S(4.5)I(4.5) nanowire soot contains three phases, two of which are insoluble with one stable phase. Microscopy and spectroscopy show that the first insoluble phase is associated mainly with spherical impurities and sediments rapidly out of solution resulting in purification. The second phase appears to consist of insoluble nanowire bundles and sediments more slowly, eventually leaving a stable dispersion of nanowire bundles. The stably dispersed bundles tend to be smaller than their insoluble counterparts. The best solvents studied were 2-propanol and dimethylformamide. Microscopy studies showed that, in the case of 2-propanol, sonication significantly reduced the bundle size relative to the unsonicated bulk. However, during sedimentation, large quantities of bundles were observed to reaggregate to form larger bundles which subsequently sedimented out of solution. In general, the sedimentation properties of the various phases did not vary significantly with concentration indicating that the insoluble nanowires are intrinsically insoluble. However, the diameter of the stably dispersed bundles decreased with concentration, until very small bundles consisting of only two or three nanowires were observed at concentrations below 0.003 mg/mL. In addition, stable composite dispersions were produced by mixing the nanowires with poly(vinylpyrrolidone) in 2-propanol opening the way for the formation of polymer/inorganic nanowire composites.