表面活性剂分子间弱相互作用的直接能量表征——高灵敏等温滴定量热法

分子间弱相互作用热力学研究的直接实验方法就是利用量热手段测定相互作用的能量参数. 本文对TAM III-ITC 纳焦级量热计进行了电标定实验和标准反应热测量, 结果显示本量热计的精密度为±0.09%; 量热用基准物质三羟甲基氨基甲烷(Tris)与盐酸的反应热((-47.48±0.12) kJ·mol^-1)与文献值一致. 采用此量热计,对典型的头-尾链型阳离子表面活性剂十二烷基三甲基溴化铵(DTAB)测量得到了与文献报导值很好吻合的临界胶束浓度(cmc)和胶束化焓, 而且对具有亲水-疏水面式刚性结构的生物表面活性剂胆酸钠(NaC)也获得了可靠的结果. 进一步地, 对于相反电荷的混合表面活性剂体系(DTAB/NaC), 分别研究了在富NaC区和富DTAB区体系混合胶束的形成. 结果说明DTAB/NaC混合表面活性剂体系在富NaC区有较强的协同效应, 而在富DTAB区的协同效应较弱. 本文结合电导率测定结果, 对DTAB/NaC混合体系在水溶液中的分子自组装热力学行为进行了有价值的讨论.     

卵清蛋白与离子型表面活性剂的相互作用

本文通过荧光光谱法、紫外-可见吸收光谱法和透射电镜并结合电导率测定分别研究了水中卵清蛋白与阴离子表面活性剂十二烷基硫酸钠（SDS）和阳离子表面活性剂十二烷基三甲基溴化铵（DTAB）和十六烷基三甲基溴化铵（CTAB）之间的相互作用。研究结果表明卵清蛋白可以增加SDS和CTAB的临界胶束浓度,但对DTAB的临界胶束浓度没有影响。阴离子表面活性剂可以使卵清蛋白构象完全伸展,而阳离子表面活性剂却不具备此种作用。表面活性剂单体与卵清蛋白的相互作用强于表面活性剂胶束与卵清蛋白的相互作用。     

接触角法测定表面活性剂的临界胶束浓度——推荐一个物理化学新实验

物理化学实验教学内容中表面活性剂溶液的临界胶束浓度(CMC)的测定通常采用表面张力法和电导率法。本实验采用接触角测定仪测定表面活性剂溶液在疏水纤维上的接触角,研究接触角随溶液浓度的变化规律,讨论了接触角法测定表面活性剂临界胶束浓度的可行性。同时采用表面张力法和电导率法分别测出了表面活性剂CTAB的临界胶束浓度,结果与接触角法一致。实验证明,接触角法操作更加简单,溶液用量少,实验结果稳定性和重复性好,可推广应用。     

四甲基溴化铵及不同链长表面活性剂对甲基纤维素-邻甲氧基肉桂酸溶液凝胶化行为的影响

测定了四甲基溴化铵以及表面活性剂十二烷基三甲基溴化铵(DTAB)、十四烷基三甲基溴化铵(TTAB)和十六烷基三甲基溴化铵(CTAB)对甲基纤维素(MC)-4邻甲氧基肉桂酸钠盐(OMC-)体系的凝胶化行为的影响.结果表明:含DTAB、TTAB以及CTAB的MC-OMC溶液的溶胶-凝胶转变温度不随表面活性剂质量分数的变化而变化,但是向MC-OMC溶液中加入四甲基溴化铵,体系的溶胶-凝胶转变温度会显著下降.在含四甲基溴化铵或不同链长表面活性剂的MC-OMC-溶液中,TTAB等表面活性剂分子更倾向于在水溶液中形成球状胶束;四甲基溴化铵与OMC-有着较强的静电作用,会导致MC和OMC-形成的核-壳结构破裂.     

用氯离子电极同时测定阳离子表面活性剂的CMC及反离子缔合度

临界胶束浓度(CMC)是研究表面活性剂的一个重要参数,胶束的反离子缔合度(K)是重要的特性参数。本文以阳离子表面活性剂十烷基三甲基氯化铵(DTMAC)、十二烷基三甲基氯化铵(DTAC)、十四烷基三甲基氯化铵(TTAC)、十六烷基三甲基氯化铵(CTAC)和十八烷基三甲基氯化铵(OTAC)水溶液体系为研究对象,用氯离子选择电极分别测定了其水溶液体系胶束的CMC和K。     

微量滴定热量计的建立和混合表面活性剂囊泡形成的研究

结合LKB-2107微量安瓶热量计和改进的Thermometric微量滴定热量计, 建立一台具有1和3 mL容积的微量滴定热量计, 并用仪器的基线噪声、基线的稳定性、能当量的测量和能量与电压(V)-时间(t)积分面积的线性关系考察了热量计灵敏度和测量精度. 分别用蔗糖的稀释热和十二烷基硫酸钠(SDS)的胶束生成热检验仪器的可靠 性. 测定了SDS和双十二烷基二甲基溴化铵(DDAB)的相互作用能, 并用量热结果讨论其相行为. 从量热实验得到, SDS与DDAB胶束的相互作用焓为?29.53 kJ/mol, SDS与DDAB反应生成盐的反应焓为?125.8 kJ/mol, 混合囊泡生成焓为41.23 kJ/mol, 囊泡再转化为富SDS胶束的焓变为32.10 kJ/mol.     

全氟辛酸钠与十二烷基三甲基溴化铵混合胶束微环境性质的NMR, ESR研究

应用表面张力法、NMR法和ESR法研究了全氟辛酸钠(SPFO)-十二烷基三甲基溴化铵(DTAB)混合体系水溶液胶束形成及混合胶束的微环境性质(微观粘度、微观极性等).结果表明,碳氟表面活性剂碳氟链和碳氢表面活性剂碳氢链之间具有强烈的相互作用,DTAB与SPFO在水溶液中形成混合胶束.DTAB与SPFO混合体系的表面活性高于单一的DTAB或SPFO,混合体系cmc较单一的DTAB和SPFO低.DTAB与SPFO混合胶束的微观粘度较DTAB胶束的大,而微观极性较DTAB的小.     

稳态荧光探针法测定三聚季铵盐表面活性剂的胶束聚集数

以芘为荧光探针, 十六烷基氯化吡啶(CPC)为猝灭剂, 以芘的饱和水溶液为溶剂配制表面活性剂溶液, 根据芘的荧光强度之比I1/I3随表面活性剂水溶液浓度的变化, 测定了三聚季铵盐表面活性剂CTTTA的cmc值, 测定值与表面张力法测定的cmc值一致；当猝灭剂CPC的浓度取0.1~0.3 mmol·L-1范围时, 用稳态荧光探针法测定了CTTTA的胶束聚集数. 实验数据表明, 表面活性剂溶液浓度为6~10倍cmc时, 胶束聚集数N随表面活性剂浓度增大而线性增大, 并用外推法得到CTTTA的临界胶束聚集数.     

全氟辛酸钠与十二烷基三甲基溴化铵混合胶束微环境性质的NMR,ESR研究

应用表面张力法、NMR法和ESR法研究了全氟辛酸钠(SPFO)-十二烷基三甲基溴化铵(DTAB)混合体系水溶液胶束形成及混合胶束的微环境性质(微观粘度、微观极性等)。结果表明, 碳氟表面活性剂碳氟链和碳氢表面活性剂碳氢链之间具有强烈的相互作用, DTAB与SPFO在水溶液中形成混合胶束。DTAB与SPFO混合体系的表面活性高于单一的DTAB或SPFO, 混合体系cmc较单一的DTAB和SPFO低。DTAB与SPFO混合胶束的微观粘度较DTAB胶束的大, 而微观极性较DTAB的小。     

胶束增敏荧光法测定甲氰菊酯的研究

在pH=6.0的Britton-Robinson缓冲溶液中,十六烷基三甲基溴化胺(CTMAB)对甲氰菊酯的荧光有增敏作用,通过对表面活性剂及用量、介质pH值、温度及放置时间的探讨,建立了增敏荧光法测定甲氰菊酯的新方法。该方法线性范围为0.14~2.3ng/mL,检出限为0.042ng/mL。方法可用于蔬菜中甲氰菊酯残留的测定。     

BCR®-701: a review of 10-years of sequential extraction analyses

A detailed quantitative analysis was performed on data presented in the literature that focused on the sequential extraction of cadmium (Cd), chromium (Cr), copper (Cu), nickel (Ni), lead (Pb) and zinc (Zn) from the certified reference material BCR-701 (lake sediment) using the three-step harmonized BCR(?) procedure. The accuracy of data reported in the literature, including precision and different measures of trueness, was assessed relative to the certified values for BCR-701. Forty data sets were accepted following extreme outlier removal, and statistically summarized with measures of central tendency, dispersion, and distribution form. In general, literature data were similar in their measurement precision to the expert laboratories used to certify the trace element contents in BCR-701. The overall median precision for literature reported data was 10% (range 6-19%), compared to certifying laboratories of 9% (range 4-33%). One measure of literature data trueness was assessed via a confirmatory approach using a robust bootstrap method. Only 22% of the comparisons indicated significantly different (all were lower) concentrations reported in the literature compared to certified values. The question of whether the differences are practically significant for environmental studies is raised. Bias was computed as a measure of trueness, and literature data were more frequently negatively biased, indicating lower concentrations reported in the literature for the six trace elements for the three-step sequential procedure compared to the certified values. However, 95% confidence intervals about the average bias for the 18 comparisons indicated only four instances when a mean bias of 0 (i.e., measured=certified) was not incorporated-suggesting statistical difference. Finally, Z-scores incorporating a Horwitz-type function were used to assess the general trueness of laboratory data. Of the 468 laboratory Z-score values computed, 92% were considered to be satisfactory, 5% were questionable, and 3% were unsatisfactory. A detailed examination of the methodology sections of the various studies showed that despite claiming adherence to the harmonized BCR sequential extraction protocol, significant deviations were commonly observed; particularly in moisture correction, sample mass, centrifugation specifics, shaking specifics, and incorporation of filtration. It is likely that failure to strictly adhere to the protocol adversely impacted accuracy, by increasing the degree of imprecision and resulting in more discrepant trueness values.     

Spectrophotometric determination of the stability constant of the Eu(III)-murexide complex

The values of the stability constants of the Ca(II) and lanthanide(III) complexes of murexide reported in the literature were determined without proper correction for binding of buffer ions to the metal ion. The constants are best determined without a buffer present. Accurate values of conditional stability constants for the Eu(III)—murexide complex (relative standard deviation better than 3%), of the differential molar absorptivity of the Eu(III)—murexide complex with respect to murexide at 480 nm (relative standard deviation better than 0.5%) and of the molar absorptivity of murexide at 520 and at 506 nm (precision better than 0.4%) at pH 5.0 and 6.5 at 15, 25 and 35° are reported. The accuracy and precision of the concentration of metal ion solution determined by using these conditional stability constants are discussed.     

Non-destructive elemental analysis of large meteorite samples by prompt gamma-ray neutron activation analysis with the internal mono-standard method

Prompt gamma-ray neutron activation analysis (PGNAA) using the internal mono-standard method was tested for its applicability to analyzing large solid samples including irregularly shaped meteorite samples. For evaluating the accuracy and precision of the method, large quantities of the Geological Survey of Japan standardized rock powders (JB-1a, JG-1a, and JP-1) were analyzed and 12 elements (B, Na, Mg, Al, Cl, K, Ca, Ti, Mn, Fe, Sm, and Gd) were determined by using Si as an internal standard element. Analytical results were mostly in agreement with literature values within 10 %. The precision of the method was also shown to be within 10 % (1σ) for most of these elements. The analytical procedure was then applied to four stony meteorites (Allende, Kimble County, Leedey, Lake Labyrinth) and four iron meteorites (Canyon Diablo, Toluca (Mexico), Toluca (Xiquipilco), Squaw Creek) consisting of large chunks or single slabs. For stony meteorites, major elements (Mg, Al, Si, S, Ca, and Ni), minor elements (Na and Mn) and trace element (B, Cl, K, Ti, Co, and Sm) were determined with adequate accuracy. For iron meteorites, results for the Co and Ni mass fractions determined are all consistent with corresponding literature values. After the analysis, it was confirmed that the residual radioactivity remaining in the sample after PGNAA was very low and decreased down to the background level. This study shows that PGNAA with the internal mono-standard method is highly practical for determining the elemental composition of large, irregularly shaped solid samples including meteorites.     

Medium-throughput pKa screening pharmaceuticals by pressure-assisted capillary electrophoresis

A fast screening method for the determination of the dissociation constants (pKa) of acidic, basic, and multivalent compounds was developed by using pressure-assisted capillary electrophoresis (PACE). External air pressure was applied to shorten the analysis time. The separation efficiency decreases as air pressure increases. However, it was found that air pressure does not affect the measurement of electrophoretic mobility and pKa significantly when it is less than 2 psi. The method was evaluated in terms of accuracy, precision, and ruggedness by using a set of 48 compounds with literature pKa values ranging from 2 to 10. The difference between the measured pKa values and literature values is less than 0.2 units. The throughput is approximately 20 compounds per day with a 12-point measurement ranging from pH 2.5 to 11. It was demonstrated that this method is applicable for pKa screening of pharmaceuticals with diverse chemical structures.     

Specific heats of aqueous solutions of NaCl,NaBr, and KCl: Comparisons with related thermal properties

Earlier unpublished measurements of the specific heat capacities of aqueous NaCl, KCl, and NaBr solutions from 5 to 85°C and from 0.05m to saturation are presented. A twin calorimeter was used. A precision of nearly 1 part in 10⁴ in the specific heat capacity is claimed. The results are compared with literature values (summaries or original data) for heat capacity, heat of dilution, and activity coefficient of these salts in solution by means of a polynomial in half-integer powers of molality and temperature. It is found that our values agree well with the more recent literature values of the heat capacities. Small systematic inconsistencies between the various types of data were found.The experimental results presented here are taken from the postdoctoral work of Dr. F. W. Lamb, 1946–47, and from the master's thesis of Dr. J. E. Tanner, Indiana University (1954), obtainable from University Microfilms, Inc., Ann Arbor, Michigan, order number M-763.     

Neutron activation analysis of 35 elements in Chinese standard rocks (GSR) and soils (GSS) using the SLOWPOKE reactor

Concentrations of 35 elements in Chinese Standard Rocks (GSR-1 to GSR-3) and Soils (GSS-1 to GSS-8) have been measured with INAA using the SLOWPOKE reactor. At the same time, the U. S. NBS reference standards: SRM-1632a (Bituminous Coal), SRM-1633a (Coal Fly Ash) and SRM-1646 (Estuarine Sediment) were also analyzed in order to cross-check the accuracy of this method. The results obtained indicate that the reproducibility of the method is satisfactory for most of the elements, namely the precision in general, is better than ±10%. Comparison of our values for NBS SRM-1632a, 1633a and 1646 with the certified values of NBS or with values cited in the literature indicates good agreement. The results were found to be accurate within ±10% error of the established results.     

Determination of chlorine in silicate rocks by neutron activation analysis

A simple radiochemical neutron activation analysis scheme has been developed for the determination of chlorine in silicate rocks. The method involves a 15-min thermal neutron irradiation of rock powder followed by a quick separation of ³⁸Cl as AgCl, and Ge(Li) spectrometry. Chemical yield, normally ranging between 95% and 100%, is monitored gravimetrically through the recovery of AgCl. The procedure has been tested on several geochemical standards to assess its accuracy and precision. The values obtained for standard rocks agree with the literature values. At the 100-ppm level, the analytical precision for chlorine is within ±5% (2σ).     

Determination of ethylene glycol dinitrate in dynamites using HPLC: application to the plastic explosive Goma-2 ECO

In this study, a sequential extraction method using water and methanol to recover ethylene glycol dinitrate or nitroglycol (EGDN) contained in Goma-2 ECO dynamite was developed. After, an HPLC method was used for the determination of EGDN in the two extracted phases. The analytical method was validated by evaluating its selectivity, sensitivity, linearity, and linear working concentration range, limit of detection and quantitation, precision (as repeatability and intermediate precision), accuracy, and robustness, providing appropriate values (i.e. RSD values for precision about 6% and accuracy about 100%). Finally, the EGDN content of a sample of the Goma-2-ECO dynamite was determined obtaining a concentration of 30.29%, which is in accordance with the manufacturer's specifications for this dynamite (25.7-31.4%).     

Confirmatory analysis of malachite green, leucomalachite green, crystal violet and leucocrystal violet in salmon by liquid chromatography-tandem mass spectrometry

A method has been developed to analyse for malachite green (MG), leucomalachite green (LMG), crystal violet (CV) and leucocrystal violet (LCV) residues in salmon. Salmon samples were extracted with acetonitrile:McIIIvain pH 3 buffer (90:10 v/v), sample extracts were purified on a Bakerbond strong cation exchange solid phase extraction cartridge. Aliquots of the extracts were analysed by LC-MS/MS. The method was validated in salmon, according to the criteria defined in Commission Decision 2002/657/EC. The decision limit (CCalpha) was 0.17, 0.15, 0.35 and 0.17 microg kg(-1), respectively, for MG, LMG, CV and LCV and for the detection capability (CCbeta) values of 0.30, 0.35, 0.80 and 0.32 microg kg(-1), respectively, were obtained. Fortifying salmon samples (n=6) in three separate assays, show the accuracy to be between 77 and 113% for MG, LMG, LCV and CV. The precision of the method, expressed as RSD values for the within-laboratory reproducibility, for MG, LMG and LCV at the three levels of fortification (1, 1.5 and 2.0 microg kg(-1)), was less than 13%. For CV a more variable precision was obtained, with RSD values ranging between 20 and 25%.     

Development and validation of a solid phase micro-extraction-gas chromatography-mass spectrometry method for the determination of furan in baby-food

An efficient and simple method for the determination of furan in baby-food (vegetables and fruits) by solid phase micro-extraction-gas chromatography-mass spectrometry (SPME-GC-MS) was developed and validated. Experimental design was used to investigate the effects of temperature and time of extraction. The calculated regression model was used to find the experimental conditions providing the optimal SPME extraction yield. Validation was carried out in terms of limit of detection (LOD), limit of quantitation (LOQ), linearity, precision and trueness. LOD and LOQ values in the low ngkg(-1) were achieved, whereas linearity was established over two order of magnitude. Good precision was obtained both in terms of intra-day repeatability and between-day precision on two concentration levels (RSD% lower than 3.6%). Recovery values of 91.5+/-6.2% and of 96.1+/-1.3% (n=3) were calculated at 75 ngkg(-1) and 75 microgkg(-1) level. Finally, the applicability of the method to the determination of furan in a number of commercial and home-made baby-food samples was demonstrated.