Carbon Dioxide Destruction with Methane Reforming by a Novel Plasma-Catalytic Converter

A novel plasma-catalyst converter (NPCC) was engineered in applying the carbon capture utilization technology for the destruction of carbon dioxide (CO₂), which is a cause of global warming and is generated from the combustion of fossil fuels. The NPCC has an orifice-type baffle to improve an amount of gas feed with the higher CO₂ destruction for a stationary point sources application . To examine its ability for the CO₂ destruction, the performance analysis was conducted on the effects of methane additive, nozzle injection velocity, total gas feed, and catalyst type. The product gas from the NPCC was combustible components like CO, H₂, CH₄, THCs. The CO₂ destruction and the CH₄ conversion at a 1.29 CH₄/CO₂ ratio were 37 and 47 %, respectively, and the energy decomposition efficiency was 0.0036 L/min W. The nickel oxide catalyst among other catalysts showed the most effectiveness for the CO₂ destruction and CH₄ conversion at a lower temperature. The carbon-black produced without the catalytic bed has carbon nanoparticles with diverse shapes, such as spherical carbon particles and carbon nanotubes; and its high conductivity and specific surface area were suitable for special electronic materials, fuel cells, and nanocomponents.     

Reduction Characteristics of Carbon Dioxide Using a Plasmatron

To decompose carbon dioxide, which is a representative greenhouse gas, a 3-phase gliding arc plasmatron device was designed and manufactured to examine the decomposition of CO₂, either alone or in the presence of methane with and without water vapour. The changes in the amount of carbon dioxide feed rate, the methane to carbon dioxide ratio, the steam to carbon dioxide ratio, and the methane to steam ratio were used as the parameters. The carbon dioxide conversion rate, energy decomposition efficiency (EDE), carbon monoxide and hydrogen selectivity, and produced gas concentration were also investigated. The maximum values of the carbon dioxide conversion rate, which is a key indicator of carbon dioxide decomposition, in different cases were compared. The maximum carbon dioxide conversion rate was 12.3 % when pure carbon dioxide was supplied; 34.5 % when methane was injected as a reforming additive; 7.8 % when steam was injected as a reforming additive; and 43 % when methane and steam were injected together. Therefore, this could be explained that the methane-and-steam injection showed the highest carbon dioxide decomposition, showing low EDE as 0.01 L/min W. Furthermore, the plasma produced carbon-black was compared with commercial carbon-black chemicals through Raman spectroscopy, surface area measurement and scanning electron microscopy. It was found that the carbon-black that was produced in this study has the high conductivity and large specific surface area. Our product makes it suitable for special electric materials and secondary battery materials applications.     

Optimizing the parameters of the steam-carbon dioxide conversion of methane by Gibbs energy minimization

The thermodynamic equilibrium for the steam-carbon dioxide conversion of methane was studied by Gibbs energy minimization. The degree of coke formation, the content of methane and carbon dioxide in the synthesis gas, and the synthesis gas H₂/CO ratio were plotted as functions of the molar ratios of CO₂/CH₄ and H₂O/CH₄ in the initial mixture at different temperatures and pressures. The regions of the optimum CH₄/CO₂/H₂O molar ratios for steam-carbon dioxide conversion were discovered, with no coke formation taking place in these regions. The optimized CH₄/CO₂/H₂O molar fractions characterized by the minimum content of methane and carbon dioxide in the synthesis gas were found for each region.     

Production of Hydrogen-Rich Syngas from Biogas Reforming with Partial Oxidation Using a Multi-Stage AC Gliding Arc System

The aim of this research work was to evaluate the possibility of upgrading the simulated biogas (70?% CH₄ and 30?% CO₂) for hydrogen-rich syngas production using a multi-stage AC gliding arc system. The results showed that increasing stage number of plasma reactors, applied voltage and electrode gap distance enhanced both CH₄ and CO₂ conversions, in contrast with the increases in feed flow rate and input frequency. The gaseous products were mainly H₂ and CO, with small amounts of C₂H₂, C₂H₄ and C₂H₆. The optimum conditions for hydrogen-rich syngas production using the four-stage AC gliding arc system were a feed flow rate of 150?cm³/min, an input frequency of 300?Hz, an applied voltage of 17?kV and an electrode gap distance of 6?mm. At the minimum power consumption (3.3?×?10^?18?W?s/molecule of biogas converted and 2.8?×?10^?18?W?s/molecule of syngas produced), CH₄ and CO₂ conversions were 21.5 and 5.7?%, respectively, H₂ and CO selectivities were 57.1 and 14.9?%, respectively, and H₂/CO (hydrogen-rich syngas) was 6.9. The combination of the plasma reforming and partial oxidation provided remarkable improvements to the overall process performance, especially in terms of reducing both the power consumption and the carbon formation on the electrode surface but the produced syngas had a much lower H₂/CO ratio, depending on the oxygen/methane feed molar ratio. The best feed molar ratio of O₂-to-CH₄ ratio was found to be 0.3/1, providing the CH₄ conversion of 81.4?%, CO₂ conversion of 49.3?%, O₂ conversion of 92.4?%, H₂ selectivity of 49.5?%, CO selectivity of 49.96?%, and H₂/CO of 1.6.     

Semiconductor Photocatalysts for Non-oxidative Coupling,Dry Reforming and Steam Reforming of Methane

Methane is one of the promising alternatives of petroleum, which should be used for not only a fuel but also a resource for hydrogen and more useful chemicals as with the petroleum. However, the selective methane conversion to them is still difficult in contrast to the combustion. Three types of photocatalytic reactions for methane conversion, i.e., the photocatalytic non-oxidative coupling of methane (2CH₄ → C₂H₆ + H₂), the photocatalytic dry reforming of methane (CH₄ + CO₂ → 2CO + 2H₂) and the photocatalytic steam reforming of methane (CH₄ + 2H₂O → 4H₂ + CO₂), can take place around room temperature or at a mild condition such as 473 K using photoenergy and semiconductor photocatalyst. In the present short review, the details of each photocatalytic reaction and the design concept of the semiconductor photocatalysts for each photocatalytic methane conversion were summarized and discussed.     

Treatment Variable Effects on Supercritical Gasification of High-Diversity Grassland Perennials

Low-input high-diversity (LIHD) mixtures of native grassland perennials were subjected to a supercritical treatment process with the aim of obtaining hydrogen-rich gases. The process was studied based on the following treatment variables: reaction temperature (374 °C to 575 °C, corresponding to a pressure range of 22.1 to 40 MPa), residence time (10 to 30 min), biomass content in the feed, and catalysts (0% to 4% NaOH and solid alkali CaO–ZrO₂). The gaseous phase produced from gasification of LIHD primarily consisted of hydrogen (H₂), with a mixture of carbon monoxide (CO), methane (CH₄), and carbon dioxide (CO₂). The statistical significance of treatment variables was evaluated using analysis of variance (ANOVA). It showed that at the level of P?<?0.05, temperature, catalysts, and biomass content in the feed significantly affected gas yields, while residence time was not significant.     

Synthesis Gas Production from CO2-Containing Natural Gas by Combined Steam Reforming and Partial Oxidation in an AC Gliding Arc Discharge

In this study, a technique of combining steam reforming with partial oxidation of CO₂-containing natural gas in a gliding arc discharge plasma was investigated. The effects of several operating parameters including: hydrocarbons (HCs)/O₂ feed molar ratio; input voltage; input frequency; and electrode gap distance; on reactant conversions, product selectivities and yields, and power consumptions were examined. The results showed an increase in either methane (CH₄) conversion or synthesis gas yield with increasing input voltage and electrode gap distance, whereas the opposite trends were observed with increasing HCs/O₂ feed molar ratio and input frequency. The optimum conditions were found at a HCs/O₂ feed molar ratio of 2/1, an input voltage of 14.5?kV, an input frequency of 300?Hz, and an electrode gap distance of 6?mm, providing high CH₄ and O₂ conversions with high synthesis gas selectivity and relatively low power consumptions, as compared with the other processes (sole natural gas reforming, natural gas reforming with steam, and combined natural gas reforming with partial oxidation).     

Conversion of Methane and Carbon Dioxide in a DBD Reactor: Influence of Oxygen

A continuous plug flow reactor supported by a dielectric barrier discharge (DBD) is used to study the conversion of methane, carbon dioxide, and oxygen at different compositions. The three studied gases were diluted with helium to 3 % with an overall flow rate of 200 sccm. The 13.56 MHz plasma was ignited at atmospheric pressure. The product stream and the inlet flow were analyzed by a FTIR spectrometer equipped with a White-cell and by a quadrupole mass spectrometer. The DBD reactor generates hydrogen, carbon monoxide, ethane, ethene, acetylene, formaldehyde, and methanol. Additional oxygen in the feed has positive effects on the yield of methanol, formaldehyde and carbon monoxide and reduces the total consumed energy. The hydrogen yield reaches its maximum at medium amounts of oxygen in the inlet flow. The conversion of methane increases to a limiting value of about 35 %. Methane rich feeds increase the yield of hydrogen, ethane and methanol. On the other hand, additional oxygen has a negative influence on the produced amount of C2 hydrocarbons. The conversion of methane and carbon dioxide as well as the yield of synthesis gas components and C2 hydrocarbons increases by changing the plasma power to higher values.     

Synthesis, characterization and activity of Co and Ni catalysts supported on AlMe (Me?=?Zn, Zr, Ti) mixed oxides

Binary Al?CTi, Al?CZr and Al?CZn oxides, prepared by the sol?Cgel method were used as supports of catalytic systems. The catalysts were prepared by impregnation of these supports with the low cost Co or Ni nitrate salts and subsequent calcination at 700?°C. Catalysts have been characterized by S_BET, XRD and TPR techniques. The catalysts were tested in ethanol partial oxidation using a fixed-bed quartz reactor at atmospheric pressure and temperature at 600?°C. In test reactions a constant feed composition was used with O₂/EtOH molar ratio of 0.75 in nitrogen balance. The catalytic performance of the systems depends on type of support and type of promoter. Hydrogen and CO are the predominant products beside some by-products in different quantities (CO₂, methane, ethylene, acetaldehyde, acetone, acetic acid). The Co and Ni catalysts supported on AlZn binary oxide showed the highest selectivity to hydrogen and to carbon monoxide with full ethanol conversion. Selectivity of hydrogen follows the order of Co(Ni)AlZn?>?Co(Ni)AlTi?>?Co(Ni)AlZr. The best performance was obtained by NiAlZn catalyst with 89?% hydrogen selectivity.     

Investigation of Dry Reforming of Methane in a Dielectric Barrier Discharge Reactor

Low temperature conversion of CH₄ and CO₂ was investigated in a coaxial dielectric barrier discharge reactor at ambient pressure. Main parameters, including the input power, the residence time, the discharge gap, the molar ratio of the feed gases and the multi-stage ionization design were evaluated to understand the ways to improve the conversion of greenhouse gases and reduce the output of by-products. At certain input power, the conversion of CH₄ and CO₂ can reach 0.797 and 0.527, respectively, when the molar ratio of CH₄/CO₂ is one. When this ratio was low to 1:5, the conversion of CH₄ was promoted to 0.843 and the selectivity to CO and H₂ was almost 100%. The multi-stage ionization favored the conversion of CO₂, which would also be an efficient design to promote the selectivity to the main products such as CO and H₂ and suppress the selectivity to the by-products.     

Effect of Nonthermal Plasma on the Methanation of Carbon Monoxide over Nickel Catalyst

Reduction of carbon monoxide to methane by hydrogen was investigated with a nonthermal plasma reactor in which Ni/alumina catalyst pellets was filled. The effect of reaction temperature, pressure and voltage on the conversion of CO was examined. It was found that the nonthermal plasma significantly enhanced the catalytic conversion of CO. The effect of the nonthermal plasma was especially remarkable at lower temperatures and pressures. At high temperatures, the catalyst itself exhibited very high catalytic activity for the conversion of CO. Since high pressure is unfavorable for creating electrical discharge plasma, the increase in pressure lowered the discharge power, thereby weakening the effect of the nonthermal plasma. With the nonthermal plasma alone, there was no conversion of CO. The reaction products identified by FTIR spectra were CH₄, CO₂ and H₂O. FTIR spectra also showed that CO was converted primarily into CH₄ with high selectivity above 90% at most experimental conditions.     

析因设计结合响应面法分析甲烷干重整过程中通过形成碳纳米管进行二氧化碳减排(英文)

A factorial experimental design was combined with response surface methodology(RSM) to opti-mize the catalyzed CO2 consumption by coke deposition and syngas production during the dry re-forming of CH4. The CH4 /CO2 feed ratio and the reaction temperature were chosen as the variables, and the selected responses were CH4 and CO2 conversion, the H2 /CO ratio, and coke deposition. The optimal reaction conditions were found to be a CH4 /CO2 feed ratio of approximately 3 at 700 °C, producing a large quantity of coke and realizing high CO2 conversion. Furthermore, Raman results showed that the CH4 /CO2 ratio and reaction temperature affect the system's response, particularly the characteristics of the coke produced, which indicates the formation of carbon nanotubes and amorphous carbon.     

Optimization of equilibrium carbon dioxide methane reforming parameters by the Gibbs free energy minimization method

The thermodynamic equilibrium in the carbon dioxide conversion of methane is studied by Gibbs energy minimization. The curves that represent the dependences of the degree of coke formation, the content of methane and carbon dioxide in syngas, and the syngas module on the CO₂/CH₄ mole ratio in the initial mixture and on temperature at various pressures, are plotted. The regions in which the CO₂/CH₄ mole ratio is optimal for carbon dioxide conversion and no coke formation occurs, and which are characterized by a minimal content of methane and carbon dioxide in syngas, are revealed.     

High-Efficient Conversion of CO<Subscript>2</Subscript> in AC-Pulsed Tornado Gliding Arc Plasma

An AC-pulsed tornado gliding arc plasma was employed for CO₂ conversion via CO₂ decomposition and dry reforming reactions. A stable and high-efficient constant arc length discharge mode was obtained in this plasma reactor. And then, CO₂ conversion was studied under this discharge mode. In the case of CH₄/CO₂ = 0, CO₂ was converted to CO and O₂ via the CO₂ decomposition reaction. Energy efficiency of 29 % was attained at CO₂ conversion of 6 %. With strong reducing agent CH₄ added into CO₂, the main contributor of CO₂ conversion changed from CO₂ decomposition to dry reforming of CH₄. Conversions of CH₄ and CO₂, energy efficiency and energy cost changed sharply at CO₂/CH₄ ratios lower than 1/4, while they changed slowly at CH₄/CO₂ ratios above 1/4. In the case of CH₄/CO₂ = 2/3, energy efficiency of 68 % and syngas energy cost of 1.6 eV/mole were achieved at CH₄ conversion of 29 % and CO₂ conversion of 22 %.     

Competitive adsorption equilibria of CO2 and CH4 on a dry coal

Gases like CO₂ and CH₄ are able to adsorb on the coal surface, but also to dissolve into its structure causing the coal to swell. In this work, the binary adsorption of CO₂ and CH₄ on a dry coal (Sulcis Coal Province, Italy) and its swelling behavior are investigated. The competitive adsorption measurements are performed at 45?°C and up to 190 bar for pure CO₂, CH₄ and four mixtures of molar feed compositions of 20.0, 40.0, 60.0 and 80.0% CO₂ using a gravimetric-chromatographic technique. The results show that carbon dioxide adsorbs more favorably than methane leading to an enrichment of the fluid phase in CH₄. Coal swelling is determined using a high-pressure view cell, by exposing a coal disc to CO₂, CH₄ and He at 45 and 60?°C and up to 140 bar. For CO₂ and CH₄ a maximum swelling of about 4 and 2% is found, whereas He shows negligible swelling. The presented adsorption and swelling data are then discussed in terms of fundamental, thermodynamic aspects of adsorption and properties which are crucial for an ECBM operation, i.e. the CO₂ storage capacity and the dynamics of the replacement of CH₄ by CO₂.     

Effect of sodium cation on the electrochemical reduction of CO<Subscript>2</Subscript> at a copper electrode in methanol

The electrochemical reduction of CO₂ with a Cu electrode in methanol was investigated with sodium hydroxide supporting salt. A divided H-type cell was employed; the supporting electrolytes were 80 mmol dm⁻³ sodium hydroxide in methanol (catholyte) and 300 mmol dm⁻³ potassium hydroxide in methanol (anolyte). The main products from CO₂ were methane, ethylene, carbon monoxide, and formic acid. The maximum current efficiency for hydrocarbons (methane and ethylene) was 80.6%, at −4.0 V vs Ag/AgCl, saturated KCl. The ratio of current efficiency for methane/ethylene, r _f(CH₄)/r _f(C₂H₄), was similar to those obtained in LiOH/methanol-based electrolyte and larger relative to those in methanol using KOH, RbOH, and CsOH supporting salts. In NaOH/methanol-based electrolyte, the efficiency of hydrogen formation, a competing reaction of CO₂ reduction, was suppressed to below 4%. The electrochemical CO₂ reduction to methane may be able to proceed efficiently in a hydrophilic environment near the electrode surface provided by sodium cation.     

Phospholipid/Polydiacetylene Vesicle-Based Colorimetric Assay for High-Throughput Screening of Bacteriocins and Halocins

Multi-phase anaerobic reactor for H₂ and CH₄ production from paperboard mill wastewater was studied. The reactor was operated at hydraulic retention times (HRTs) of 12, 18, 24, and 36 h, and organic loading rates (OLRs) of 2.2, 1.5, 1.1, and 0.75 kg chemical oxygen demand (COD)/m³ day, respectively. HRT of 12 h and OLR of 2.2 kg COD/m³ day provided maximum hydrogen yield of 42.76?±?14.5 ml/g COD_removed and volumetric substrate uptake rate (?rS) of 16.51?±?4.43 mg COD/L h. This corresponded to the highest soluble COD/total COD (SCOD/TCOD) ratio of 56.25?±?3.3 % and the maximum volatile fatty acid (VFA) yield (Y_VFA) of 0.21?±?0.03 g VFA/g COD, confirming that H₂ was mainly produced through SCOD conversion. The highest methane yield (18.78?±?3.8 ml/g COD_removed) and ?rS of 21.74?±?1.34 mgCOD/L h were achieved at an HRT of 36 h and OLR of 0.75 kg COD/m³ day. The maximum hydrogen production rate (HPR) and methane production rate (MPR) were achieved at carbon to nitrogen (C/N) ratio of 47.9 and 14.3, respectively. This implies the important effect of C/N ratio on the distinction between the dominant microorganism bioactivities responsible for H₂ and CH₄ production.     

Reaction of nitrous oxide with methane to synthesis gas: A thermodynamic and catalytic study

The aim of the present study is to explore the coherence of thermodynamic equilibrium predictions with the actual catalytic reaction of CH4 with N_2O,particularly at higher CH4 conversions.For this purpose,key process variables,such as temperature(300℃-550℃) and a molar feed ratio(N_2O/CH4 = 1,3,and 5),were altered to establish the conditions for maximized H_2 yield.The experimental study was conducted over the Co-ZSM-5 catalyst in a fixed bed tubular reactor and then compared with the thermodynamic equilibrium compositions,where the equilibrium composition was calculated via total Gibbs free energy minimization method.The results suggest that molar feed ratio plays an important role in the overall reaction products distribution.Generally for N_2O conversions,and irrespective of N_2O/CH_4 feed ratio,the thermodynamic predictions coincide with experimental data obtained at approximately 475℃-550℃,indicating that the reactions are kinetically limited at lower range of temperatures.For example,theoretical calculations show that the H2 yield is zero in presence of excess N2O(N_2O/CH_4 = 5).However over a Co-ZSM-5 catalyst,and with a same molar feed ratio(N_2O/CH_4) of 5,the H_2 yield is initially 10%at 425℃,while above450℃ it drops to zero.Furthermore,H_2 yield steadily increases with temperature and with the level of CH4 conversion for reactions limited by N_2O concentration in a reactant feed.The maximum attainable(from thermodynamic calculations and at a feed ratio of N_2O/CH4=3) H_2 yield at 550℃ is 38%,whereas at same temperature and over Co-ZSM-5,the experimentally observed yield is about 19%.Carbon deposition on Co-ZSM-5 at lower temperatures and CH4 conversion(less than 50%) was also observed.At higher temperatures and levels of CH_4 conversion(above 90%),the deposited carbon is suggested to react with N_2O to form CO_2.     

Rotating ring-disk voltammetry: Diagnosis of catalytic activity of metallic copper catalysts toward CO<Subscript>2</Subscript> electroreduction

Using the rotating ring (platinum)—disk (glassy carbon) electrode methodology, electrocatalytic activity of the microstructured copper centers (imbedded within the polyvinylpyrrolidone polymer matrix and deposited onto the glassy carbon disk electrode) has been monitored during electroreduction of carbon dioxide both in acid (HClO₄) and neutral (KHCO₃) media as well as diagnosed (at Pt ring) with respect to formation of the electroactive products. Combination of the stripping-type and rotating ring-disk voltammetric approaches has led to the observation that, regardless the overlapping reduction phenomena, the reduction of carbon dioxide at copper catalyst is, indeed, operative and coexists with hydrogen evolution reaction. Using the fundamental concepts of surface electrochemistry and analytical voltammetry, the reaction products (thrown onto the platinum ring electrode) could be considered and identified as adsorbates (on Pt) under conditions of the stripping-type oxidation experiment. Judging from the potentials at which the stripping voltammetric peaks appear in neutral CO₂-saturated KHCO₃ (pH 6.8), formic acid or carbon monoxide seem to be the most likely reaction products or intermediates. The proposed methodology also permits correlation between the CO₂ electroreduction products and the potentials applied to the disk electrode. By performing the comparative stripping-type voltammetric experiments in acid medium (HClO₄ at pH 1) with the adsorbates of formic acid, ethanol and acetaldehyde (on Pt ring), it can be rationalized that, although C₂H₅OH or CH₃CHO are very likely CO₂-reduction electroactive products, formation of some HCOOH, CH₃OH or even CO cannot be excluded.     

DC-Pulsed Plasma for Dry Reforming of Methane to Synthesis Gas

The carbon dioxide reforming of methane to synthesis gas under DC-pulsed plasma was investigated. The effects of specific input energy and feed ratio on the product distribution and also feed conversion was studied. At the input energy of about 11 eV/molecule per methane and/or carbon dioxide the feed conversion of 38% for CH₄ and 28% for CO₂ and product selectivity of 74% has been attained for H₂ and CO at feed flow rate of 90 ml/min. The energy consumption in this work displays potential to further study and optimization of the process. The importance of the electron impact reactions in the process was discussed. The results show that by prudent tuning of system variables, the process be able to run in the way of synthesis gas, instead of hydrocarbon production.