Slurry sampling fluorination assisted electrothermal vaporization-inductively coupled plasma-atomic emission spectrometry for the direct determination of metal impurities in aluminium oxide ceramic powders

A new analytical procedure for the direct determination of metal impurities (Cr, Cu, Fe and V) in aluminium oxide ceramic powders by slurry sampling fluorination assisted electrothermal vaporization-inductively coupled plasma-atomic emission spectrometry (ETV-ICP-AES) is reported. A polytetrafluoroethylene (PTFE) emulsion was used as a fluorinating reagent to promote the vaporization of impurity elements in aluminium oxide ceramic powders from the graphite tube. A vaporization stage with a long ramp time and a short hold time provided the possibility of temporal analyte-matrix separation. The experimental results indicated that a 10 μL 1% m/v slurry of aluminium oxide could be destroyed and vaporized completely with 600 μg PTFE under the selected conditions. Two aluminium oxide ceramic powder samples were used without any additional pretreatment. Analytical results obtained by using standard addition method with aqueous standard solution were checked by comparison of the results with pneumatic nebulization (PN)-ICP-AES based on the wet-chemical decomposition and analyte-matrix separation. The limits of detection (LODs) between 0.30 μg g^–1 (Fe ) and 0.08 μg g^–1 (Cu) were achieved, and, the repeatability of measurements was mainly better than 10%. Received: 28 August 2000 / Revised: 1 November 2000 / Accepted: 12 November 2000     

The use of electrothermal vaporization ICP-OES for the determination of trace elements in human hair using slurry sampling and PTFE as modifier

A procedure for the determination of trace elements in human hair has been proposed by electrothermal vaporization inductively coupled plasma optical emission spectrometry (ETV-ICP-OES) with slurry sampling. Slurry was prepared by immersing human hair with conc. HNO₃ and then adding a polytetrafluoroethylene (PTFE) slurry, which was used as a chemical modifier for the improvement of vaporization characteristic of analyte. The slurry was homogenized with an ultrasonic vibrator before the measurement. The vaporization behaviour of the analytes in slurry and solution and the main influence factors for the determination were studied with the addition of PTFE systematically. Detection limits for this method varied from 0.033?µg?g^?1 (Cu) to 3.21?µg?g^?1 (Zn) with the relative standard deviations (RSDs) of 2.8–7.1%. The proposed method was successfully applied for the determination of trace elements (Cu, Mn, Cr, Fe, Zn, Cd and Pb) in human hair with minimum chemical pretreatment and aqueous calibration. The accuracy was checked by comparing the results of this method with those using pneumatic nebulization (PN) ICP-OES after a conventional acid decomposition of the same sample. In addition, the standard reference material of human hair (GBW 07601) was analysed with good agreement between the results from the proposed method and the certified values.     

Direct determination of trace copper and chromium in silicon nitride by fluorinating electrothermal vaporization inductively coupled plasma atomic emission spectrometry with the slurry sampling technique

A method has been developed for the determination of trace impurities in silicon nitride (Si₃N₄) powders by fluorination assisted electrothermal vaporization (ETV) /ICP-AES using the slurry sampling technique. Polytetrafluoroethylene (PTFE) emulsion as a fluorinating reagent not only effectively destroys the skeleton of Si₃N₄, but also carries out selective volatilization between the impurity elements (Cu, Cr) and the matrix (Si). The experimental parameters influencing fluorination reactions were optimized. The detection limits for Cu and Cr are 1.05 ng/mL ( Cu) and 1.58 ng/mL (Cr), the RSDs are in the range of 1.9–4.2%. The proposed method has been applied to the determination of Cu and Cr in Si₃N₄ ceramic powders. The analytical results were compared with those obtained by independent methods.     

Direct analysis of tantalum powders by electrothermal vaporization inductively coupled plasma atomic emission spectrometry

A direct inductively coupled plasma atomic emission method for the determination of Ag, Al, As, Ca, Cd, Co, Cu, Fe, Ga, K, Li, Mg, Na and Pb in high-purity tantalum powders has been developed. The electrothermal vaporization technique using a modified longitudinally-heated Grün-ETAAS furnace with sample introduction on a platform and an automated sampling workstation provided the possibility of in situ analyte-matrix separation, freedom of blank, and applicability to routine analysis. Hard- and software were modified to allow signal recording and data processing independent of the spectrometer software. The extent of spectral interferences by Ta-emission at the analyte wavelengths used was determined and the analyte signals of each sample run were automatically corrected. Limits of detection ranging from 5 ng/g (Ag, Cu) to 250 ng/g (K, Pb) were obtained using optimized furnace and spectrometer conditions. The method was applied to the analysis of two tantalum samples and the results for Cu, Fe, K, Mg and Na were compared with those obtained by liquid and solid-samping ETAAS, showing satisfactory agreement.     

The effect of palladium modifier on the efficiency of antimony hydride trapping in graphite furnace atomic absorption spectrometry (AAS)

A slurry fluorination electrothermal vaporization (ETV)-ICP-AES method for the determination of Cu and Cr in SiO₂ powders has been developed. A polytetrafluoroethylene (PTFE) emulsion is used as fluorinating reagent; the matrix (Si) is partially separated from the sample by selecting the ashing temperature and time to reduce the interference. Moreover, the vaporization behaviour has been investigated in detail. The detection limits are 1.1 ng/mL with 3.8% of RSD (Cu) and 1.6 ng/mL with 3.2% of RSD (Cr). The method is applied to analyze the SiO₂ powders with satisfactory results. Received: 6 January 1997 / Revised: 13 March 1997 / Accepted: 28 March 1997     

Direct determination of trace copper and chromium in silicon nitride by fluorinating electrothermal vaporization inductively coupled plasma atomic emission spectrometry with the slurry sampling technique

A method has been developed for the determination of trace impurities in silicon nitride (Si₃N₄) powders by fluorination assisted electrothermal vaporization (ETV) /ICP-AES using the slurry sampling technique. Polytetrafluoroethylene (PTFE) emulsion as a fluorinating reagent not only effectively destroys the skeleton of Si₃N₄, but also carries out selective volatilization between the impurity elements (Cu, Cr) and the matrix (Si). The experimental parameters influencing fluorination reactions were optimized. The detection limits for Cu and Cr are 1.05 ng/mL ( Cu) and 1.58 ng/mL (Cr), the RSDs are in the range of 1.9–4.2%. The proposed method has been applied to the determination of Cu and Cr in Si₃N₄ ceramic powders. The analytical results were compared with those obtained by independent methods. Received: 8 December 1998 / Revised: 1 February 1999 / Accepted: 3 February 1999     

Slurry Sampling Electrothermal Vaporization Combined with ICP-AES for Direct Analysis of Environmental Samples

In this article, a polytetrafluoroethylene (PTFE) slurry was used as a chemical modifier for direct determination of trace elements in environmental samples by electrothermal vaporization inductively coupled plasma atomic emission spectrometry (ETV-ICP-AES) with slurry sampling. The vaporization behaviors of the analytes in slurry and solution were comparatively studied in the presence of PTFE. The main influence factors for this method were examined. Under the optimum operating conditions, the precision of this method was better than 7% with the detection limits varying from 1.7 ng mL^?1 (Cu) to 203 ng mL^?1 (Zn). The proposed method has been applied to the direct determination of the trace elements in camphor tree leaves and standard reference material (the combined sample of branch and leaf of shrub, GBW 07603) with satisfactory results.     

悬浮液进样电感藕合等离子体发射光谱中颗粒的输运和蒸发行为

以碳化硼为例,研究了悬浮液雾化进样中的粒子在传输和蒸发过程中的行为,并对分析结果出现负偏离的原因进行了详细探讨.对比悬浮液颗粒的原始粒径分布和经过传输过程后的粒径分布,获得到达等离子体的颗粒粒径上限小于10 Am.样品中存在的部分超大粒径的颗粒(d>>10 μm)会严重影响可传输区域颗粒(d<10 μm)的质量运输效率...     

Study on the direct analysis of solid powder biological samples using fluorination assisted electrothermal vaporization inductively coupled plasma atomic emission spectrometry with PTFE slurry modifier

A method has been described for the direct determination of Ti, Cu, Mn, Cr and Cd in solid biological samples without any chemical pretreatment by fluorination assisted electrothermal vaporization inductively coupled plasma atomic emission spectrometry (ETV-ICP-AES) with slurry sampling. A polytetrafluorethylene (PTFE) emulsion was used as a fluorinating reagent to promote the vaporization of the analytes from the graphite furnace. The interface between furnace device and ICP torch and the main factors affecting the analytical signal were investigated systematically. The detection limits for the determination of Ti, Cu, Mn, Cr and Cd are 6.3, 4.7, 10, 13 and 278 ng/mL, respectively; the relative standard deviations are in the range of 1.5 (Mn) ∼4.0% (Cd) after optimization of the operating conditions. The recommended approach has been applied to directly determine the trace elements of interest in the Chinese traditional medicine Loulu and in the solid biological standard reference material (peach leaves, GBW 08501) with satisfactory results. Received: 28 December 1998 / Revised: 9 February 1999 / Accepted: 12 February 1999     

Study on the direct analysis of solid powder biological samples using fluorination assisted electrothermal vaporization inductively coupled plasma atomic emission spectrometry with PTFE slurry modifier

A method has been described for the direct determination of Ti, Cu, Mn, Cr and Cd in solid biological samples without any chemical pretreatment by fluorination assisted electrothermal vaporization inductively coupled plasma atomic emission spectrometry (ETV-ICP-AES) with slurry sampling. A polytetrafluorethylene (PTFE) emulsion was used as a fluorinating reagent to promote the vaporization of the analytes from the graphite furnace. The interface between furnace device and ICP torch and the main factors affecting the analytical signal were investigated systematically. The detection limits for the determination of Ti, Cu, Mn, Cr and Cd are 6.3, 4.7, 10, 13 and 278 ng/mL, respectively; the relative standard deviations are in the range of 1.5 (Mn) ∼4.0% (Cd) after optimization of the operating conditions. The recommended approach has been applied to directly determine the trace elements of interest in the Chinese traditional medicine Loulu and in the solid biological standard reference material (peach leaves, GBW 08501) with satisfactory results. Received: 28 December 1998 / Revised: 9 February 1999 / Accepted: 12 February 1999     

Analysis of aluminium-based ceramic powders by electrothermal vaporization inductively coupled plasma atomic emission spectrometry using a tungsten coil and slurry sampling

Slurry sampling followed by electrothermal vaporization was used as sample introduction technique for digestion-free analysis of aluminium nitride and aluminium oxide by inductively coupled plasma atomic emission spectrometry. The vaporizer consisted of a tungsten coil in a quartz chamber. Spectral interferences and background emission caused by tungsten ablation from the coil were reduced by coating it with tungsten carbide. Different approaches for background correction techniques were considered. The analytes Ca, Cd, Co, Cr, Cu, Fe, Mg, Ni and Zn were determined simultaneously, whereas Mn and Na were determined in the sequential mode. Calibration was performed using the standard additions method. The accuracy was checked by comparison of the results with those of independent methods. Detection limits between 0.01 (Mg) and 8.5 μg/g (Co) were achieved.     

Determination of traces of iron in indium phosphide by electrothermal atomic absorption spectrometry combined with solvent extraction

An electrothermal atomic absorption (ETAAS) method for the determination of traces of iron (0.1-1.0 microgram g-1) in Fe-doped indium phosphide (InP) has been developed. In order to overcome the indium matrix-effect and to achieve a useful detection limit, a preliminary solvent-extraction of Fe(III) with acetylacetone (HAA) is necessary. After sample dissolution with hydrochloric acid (1 + 1) the digest is evaporated to dryness, Fe(II) is oxidized to Fe(III) with nitric acid, the residue is dissolved in 0.01 mol L-1 HCl and the iron is extracted at pH 2.0 with 0.5 mol L-1 HAA in toluene. The organic phase is injected into the graphite furnace and the iron is directly evaluated by external organic standard calibration. The limit of detection (3SB) resulting from further in-situ preconcentration is 0.03 microgram g-1. When the method was applied to the analysis of real samples containing 0.2-0.7 microgram g-1 Fe, the RSD was in the range 8-21%. Results were compared with those independently obtained on the decomposed sample solution with inductively coupled atomic emission spectrometry (ICP-AES). The detection limit of the ICP-AES method, that needs matrix-matched standards, is 0.20 microgram g-1.     

In-situ separation of the matrix for the direct determination of traces of chromium, cobalt, and nickel in titanium dioxide powder by electrothermal atomic-absorption spectrometry with slurry sampling

A novel method has been developed for the direct determination of traces of chromium, cobalt, and nickel in TiO2 powder; it entails slurry sampling and electrothermal atomic-absorption spectrometry (ETAAS) with a polytetrafluoroethylene (PTFE) slurry (6% m/v) as fluorinating reagent. The factors which could affect the vaporization of the matrix and analytes were studied in detail; the fluorinating vaporization behavior of the analyte both in the slurry and in solution were also investigated. Owing to the in-situ separation of the matrix, the matrix influences were reduced significantly. The proposed method has been applied to the direct determination of traces of chromium, cobalt, and nickel in high-purity TiO2 powder without chemical pretreatment. Under the optimum experimental conditions the detection limits of the analytes (Cr, Co, and Ni) were 1.9 ng g(-1), 2.4 ng g(-1) and 5.4 ng g(-1), respectively, the relative standard deviations (RSD) were 3.4% (n=6, c=7.0 ng mL(-1)), 2.9% (n=6, c=0.70 ng mL(-1)), and 7.6% (n=6, c=4.0 ng mL(-1)), again respectively, and the characteristic masses for Cr, Co, and Ni were 8.4 pg/ 0.0044A, 9.3 pg/0.0044A, and 40.0 pg/0.0044A, respectively.     

Investigations on the use of chemical modifiers for the direct determination of trace impurities in Al2O3 ceramic powders by slurry electrothermal evaporation coupled with inductively-coupled plasma mass spectrometry (ETV-ICP-MS)

The direct determination of trace impurities in Al2O3 ceramic basic powders by ICP-MS using electrothermal evaporation (ETV) with slurry sampling has been investigated. To increase interference-free analyte volatilization, the use of the palladium-group modifiers (PGM) IrCl3, Pd(NO3)2, and PdCl2 for the determination of Ca, Fe, Ga, Mg, Mn, Na, Ni, and V in Al2O3 powders was studied. Their role, which in ETV-ICP-MS and ETV-ICP-OES is to stabilize the investigated analyte during the ashing phase, to increase vaporization of the matrix, and to reduce transport losses was investigated. Optimum analysis results were obtained with PdCl2 modifier when 500 ng Pd was used for a sample weight of 100 microg Al2O3 injected into the ETV. Calibration was performed by standard addition with aqueous solutions of the analytes. The RSDs calculated from triplicate analysis ranged form 5 to 10%. Detection limits between 0.07 microg g(-1) (Ga) and 1.1 microg g(-1) (Na) were achieved. The accuracy was proven for the elements Ca, Fe, Ga, Mg, Mn, Na, Ni, and V by analyzing an NIST standard reference Al2O3 material (SRM 699) with a middle grain size of 16.4 microm. The analytical method was used for the analysis of Al2O3 powder (AKP 30, Sumitomo, Japan) with impurities in the low microg g(-1) range and a middle grain size of 1.1 microm. The results obtained for the elements Ca, Fe, Ga, Mg, Mn, Na, Ni, and V were comparable with those obtained by ICP-MS subsequent to conventional decomposition with hydrochloric acid at high pressure.     

Analysis of aluminium-based ceramic powders by electrothermal vaporization inductively coupled plasma atomic emission spectrometry using a tungsten coil and slurry sampling

Slurry sampling followed by electrothermal vaporization was used as sample introduction technique for digestion-free analysis of aluminium nitride and aluminium oxide by inductively coupled plasma atomic emission spectrometry. The vaporizer consisted of a tungsten coil in a quartz chamber. Spectral interferences and background emission caused by tungsten ablation from the coil were reduced by coating it with tungsten carbide. Different approaches for background correction techniques were considered. The analytes Ca, Cd, Co, Cr, Cu, Fe, Mg, Ni and Zn were determined simultaneously, whereas Mn and Na were determined in the sequential mode. Calibration was performed using the standard additions method. The accuracy was checked by comparison of the results with those of independent methods. Detection limits between 0.01 (Mg) and 8.5 μg/g (Co) were achieved. Received: 21 September 1998 / Revised: 30 October 1998 / Accepted: 3 November 1998     

Electrothermal vaporization in inductively coupled plasma atomic emission spectrometry for direct multielement analysis of food samples with slurry sampling

Slurry sampling followed by electrothermal vaporization (ETV) was used as sample introduction technique in inductively coupled plasma atomic emission spectrometry (ICP-AES) for the direct determination of trace elements in food samples. A polytetrafluoroethylene (PTFE) emulsion was used as a fluorinating reagent to promote vaporization and the transportation of analytes. The main factors affecting the analytical signals were investigated in detail. Under optimum operating conditions, the detection limits (DL) for this method varied from 1.8 (Cu) to 215 ng/mL (Zn), while the relative standard deviations (RSD) were in the range 2.6% (Cu)-7.2% (Zn). The proposed method was successfully applied to the direct determination of trace amounts of V, Cu, Cr, Fe, Zn, and La in rice without any chemical pretreatment. The precision was evaluated by analyzing a standard reference material (tea leaves, GBW 07605) and comparing the results from this method with results obtained by pneumatic nebulization (PN) ICP-AES after the wet-chemical decomposition of the same sample.From Zhurnal Analiticheskoi Khimii, Vol. 60, No. 3, 2005, pp. 286–290.Original English Text Copyright © 2005 by Chen.This article was submitted by the author in English.     

Direct determination of trace rare earth elements in high purity Y2O3 using fluorination assisted electrothermal vaporization inductively coupled plasma atomic emission spectrometry with slurry sampling

A new method for the determination of trace amounts of 14 rare earth elements in high purity Y₂O₃ using fluorination assisted electrothermal vaporization inductively coupled plasma atomic emission spectrometry with slurry sampling was developed. A polytetrafluoroethylene (PTFE) emulsion was used as a fluorinating reagent to promote the vaporization of the analytes from graphite furnace. The main factors affecting analytical signals were investigated systematically. The interference of matrix could be minimized in the presence of PTFE. Under optimum conditions, the detection limits for rare earth elements were 0.032 ng～2.52 ng and the relative standard deviations were in the range of 1.4% to 4.3%. The proposed method was applied to the direct analysis of high purity Y₂O₃ powder with satisfactory results.     

Determination of Cu, Fe, Mn, and Zn in blood fractions by SEC-HPLC-ICP-AES coupling

The binding of Cu, Fe, Mn, and Zn to proteins in blood and in blood fractions was investigated, since their interactions in free radical metabolism in humans is of great interest. An HPLC-ICP-AES technique was developed allowing adequate separation of metalloproteins and of inorganic and organic metal species. For the separation of metalloproteins in erythrocytes and blood plasma a Merck Superformance Fractogel EMD BioSEC 650 (S) column was used. Size exclusion chromatography (SEC)-HPLC was hyphenated to ICP-AES both on-line and off-line for the detection of trace elements in the fractions resulting from HPLC separations. HPLC parameters, pH, temperature, flow rate and salt concentration were optimized for the protein separation and the optimal conditions were applied for the hyphenation to the ICP-AES detector. The separation column was calibrated with five standard proteins. For the element determination by ICP-AES a line selection with respect to the sensitivity was performed. Three different methods were used for the determination of trace elements in blood: direct determinations, on-line and off-line SEC-HPLC-ICP-AES measurements. For the optimizing experiments blood samples of one female subject were used. The direct determination by ICP-AES of the elements was performed in blood and blood fractions of ten different subjects to obtain the average concentration ranges. From the results the identification of the protein Cu/Zn superoxide dismutase in erythrocytes was possible. The LOD were 0.03 microgram mL-1 for Cu, 0.026 microgram mL-1 for Fe, 0.8 ng mL-1 for Mn, and 0.09 microgram mL-1 for Zn in a synthetic blood matrix.     

Some topical applications of plasma atomic spectrochemical methods for the analysis of ceramic powders

The scope of a number of plasma spectrochemical methods for the determination of the main components and impurities in ceramic powders is described. These methods meet the requirements for the analytical characterization of new structural and functional ceramics for modern industrial applications and electronic devices. For ceramic powders, spectrochemical analysis with direct methods as well as analysis subsequent to sample dissolution are discussed. Fusion is a powerful method for the dissolution of ZrO₂ ceramic powders, provided the fluxes are pure enough. For determinations in Al₂O₃, SiC and ZrO₂, it will be shown that ICP-MS is very useful. This is especially true for trace analysis after matrix removal. The latter can easily be performed on-line in the case of the analysis of Al₂O₃ powders. For direct analysis of ceramic powders, the direct insertion of samples into the plasma, spark and arc ablation, laser ablation, electrothermal vaporization and slurry nebulization are discussed. Particular attention is given to the direct analysis of ceramics in powder form (Al₂O₃, SiC, Si₃N₄, B₄, WC) using ICP-OES with slurry nebulization as well as with direct sample insertion (DSI) and with electrothermal vaporization (ETV). For the two latter methods, the use of chemical modifiers for volatile compound formation will be shown to be of great importance, and its features will be explained using thermochemical considerations.     

Direct determination of silicon in powdered aluminium oxide by use of slurry sampling with in situ fusion graphite-furnace atomic-absorption spectrometry

A direct method for determination of silicon in powdered high-purity aluminium oxide samples, by slurry sampling with in situ fusion graphite-furnace atomic-absorption spectrometry (GF-AAS), has been established. A slurry sample was prepared by 10-min ultrasonication of a powdered sample in an aqueous solution containing both sodium carbonate and boric acid as a mixed flux. An appropriate portion of the slurry was introduced into a pyrolytic graphite furnace equipped with a platform. Silicon compounds to be determined and aluminium oxide were fused by the in situ fusion process with the flux in the furnace under optimized heating conditions, and the silicon absorbance was then measured directly. The calibration curve was prepared by use of a silicon standard solution containing the same concentration of the flux as the slurry sample. The accuracy of the proposed method was confirmed by analysis of certified reference materials. The proposed method gave statistically accurate values at the 95% confidence level. The detection limit was 3.3 microg g(-1) in solid samples, when 300 mg/20 mL slurry was prepared and a 10 microL portion of the slurry was measured. The precision of the determination (RSD for more than four separate determinations) was 14% and 2%, respectively, for levels of 10 and 100 microg g(-1) silicon in aluminium oxide.