温度对fcc铁中氦行为的影响研究

温度对fcc铁中的氦行为具有重要的影响,编写了居于fcc晶格的面向对象动力学蒙特卡罗程序（Object Kinetic Monte Carlo）,采用该程序结合分子动力学（MD）方法对fcc铁中的氦行为进行多尺度模拟,研究了温度对fcc铁中氦行为的影响,给出了不同温度退火过程中氦行为的原子细节。模拟结果表明引入一定量的非热平衡空位可以使模拟结果与文献实验结果有非常好的吻合;室温至1073K,温度对氦行为影响可以分为四个阶段：第一阶段,298-473K,正电子长寿命随退火温度增加略有减少,这主要由于非热平衡空位浓度降低;第二阶段,473-673K,正电子长寿命随退火温度增加而增加,主要由于晶粒内平均氦泡尺寸增加;第三阶段,673-873K,正电子长寿命随退火温度增加而迅速减少,主要是由于氦泡的平均尺寸减小和晶粒内的空位浓度降低;第四阶段,873-1073K,正电子长寿命随退火温度增加而迅速增加,与晶粒内氦泡的平均尺寸变大,且空位浓度随温度的增加而指数增加有关。     

氦在球磨贮氢合金中的存在行为研究

通过正电子寿命测量及结构分析，研究了氦气氛球磨LaNi4.75Al0.25和Zr50Co50贮氢合金中氦的存在行为.研究结果表明：随着气氛压力增加，氦的溶入量增加，相对而言，LaNi4.75Al0.25更有利于氦的溶入；球磨样品正电子寿命的特征参数发生变化，这表明氦在材料中存在行为的差异；对于Zr50Co50合金，氦首先填充在超细晶粒的三叉晶界或空位团处，随着气氛压力增加，有小部分氦填入单空位的自由体积处，形成空位-氦复合体；对于LaNi4.75Al0.25合金，氦首先进入单空位大小的自由体积中，形成空位 关键词： 正电子寿命 氦引入 高压球磨 贮氢合金     

Hg1-xCdxTe晶体缺陷的正电子湮没寿命

利用正电子(e⁺)湮没寿命谱实验研究了Hg_1-xCd_xTe晶体样品的空位缺陷.碲溶剂法生长的样品，不论是n型导电还是p型导电都存在大量的Hg空位.经过合适的退火工艺，p型材料转为n型，同时对正电子的俘获效应减小，表现为正电子湮没平均寿命值减小14—17ps.若退火温度高于350℃，正电子湮没寿命值又增大，表明Hg空位浓度增加.得到HgCdTe中正电子的体寿命为τ_b=272ps.根据正电子湮没寿命和电参数的测量结果，得出 关键词：     

形变充氢多晶纯钴中缺陷的正电子湮没研究

用正电子寿命和多普勒线形参数测量技术,研究了形变和形变充氢多晶钴试样的缺陷性质及其回复行为。观察到形变样品阴极充氢后,氢致缺陷为一定量的位错和空位以及少量的空位团。没有观察到微空洞和微裂纹的产生。单空位的回复温度范围为73—260℃,位错和空位团的退火发生在350—670℃温度范围。测得空位的迁移激活能为E_v^m=1.09±0.07eV。 关键词：     

充氚时效不锈钢微观断裂机制

不锈钢材料在氚环境中长期工作时不仅存在着氢脆问题，同时还由于进入基材内部的氚衰变而产生氦，发生氦的积累，造成材料性能下降，甚至导致材料被破坏，即产生所谓“氦脆”现象。本课题2002年进行了样品的高温气相充氚实验以及充氚后一些显微组织分析工作。2003年对充氚＋1a时效的HR-2不锈钢样品进行了TEM动态拉伸实验观察。初步表明，充氚促进裂纹尖端位错的发射和增殖：对于HR-2不锈钢，充氚使无位错区（DFZ）减小甚至消失。2004年，充氚样品经历2a的室温时效，积累了一定的氦量，实验试图探索氦对微观断裂机制的影响。     

用正电子湮没研究纳米碲化铋的缺陷及其对热导率的影响

利用水热法合成了Bi₂Te₃纳米粉末, 并在300–500 ℃的温度范围内对其进行等离子烧结. X射线衍射测试表明制得的Bi₂Te₃粉末是单相的. 对于300–500 ℃范围内烧结的样品, 扫描电子显微镜观察发现随着烧结温度的升高样品颗粒明显增大, 但是根据X射线衍射峰的宽度计算得到的样品晶粒大小并没有明显的变化. 正电子湮没寿命测试结果表明, 所有的样品中均存在空位型缺陷, 而这些缺陷很可能存在于晶界处. 正电子平均寿命随着烧结温度的升高而单调下降, 说明较高的烧结温度导致了空位型缺陷浓度的降低. 另外, 随着烧结温度从300 ℃升高到500 ℃, 样品的热导率从0.3 W·m^-1·K^-1升高到了2.4 W·m^-1·K^-1, 这表明在纳米Bi₂Te₃中, 空位型缺陷和热导率之间存在着密切的联系.     

含氢氦锆膜的中子反射及弹性反冲探测表征

采用直流磁控溅射方法制备含氢氦的锆膜,利用中子反射和弹性反冲探测两种方法分别对样品中的氢、氦分布以及浓度进行表征,并探究了不同温度退火处理后H、He的变化.实验结果表明:中子反射与弹性反冲探测两种方法的表征结果具有很好的一致性,H、He在锆层中近似均匀分布,氦浓度与溅射的He/Ar比成正比. 300℃退火处理1 h后,样品中的H从Zr层向外迁移和释放,且这种现象随退火温度升高到500℃时更加明显.     

He注入单晶Si表面形貌的变化研究

沿Si的（100）面注入He离子, 能量为30 keV、 剂量为5×1016 ions/cm2。 注入后样品切成几块, 在真空炉中分别做退火处理, 退火温度从600 ℃到1 000 ℃, 退火时间均为30 min。 利用原子力显微镜研究了各个样品表面形貌的演化。 发现样品表面形貌与退火温度相关联。 假设在气泡中He原子与空位的比值很高, 导致样品内部存在高压的He泡, 从而使样品表面形貌发生变化。 探讨了在Si中He泡随退火温度的演化和He原子在材料中的释放机制及其对表面的影响。     

纳米Cu固体材料的X射线衍射与正电子湮没研究

 采用自悬浮-冷压法,在不同压力下制得纳米Cu固体材料并对其在不同温度和保温时间下进行退火,利用X射线衍射(XRD)和正电子湮没寿命谱(PAS)分析对材料的结构和微观缺陷进行了表征。XRD分析表明,压制而得的样品晶粒度为20 nm,低于300 ℃退火3 h后并未发现晶粒显著长大;PAS分析表明,压制后的样品缺陷主要为单空位和空位团,大空隙很少,随着退火温度的升高和退火时间的延长,单空位通过扩散结合成空位团,大空隙也在温度较高时分解为空位团,导致空位团的含量增加,而单空位和大空隙的含量降低。     

AA 2037新型连铸铝合金热轧板退火的正电子湮没研究

应用正电子湮没等技术对AA 2037连铸铝合金热轧板不同温度退火下空位-溶质相互作用及沉淀相进行了研究， 研究表明：室温时效形成的主要是空位-铜复合体以及空位-镁-铜复合体；温度为200℃退火时由于过渡相的形成正电子平均寿命出现峰值，符合多普勒展宽谱的商谱中观察到锰信号的存在，表明形成了空位-镁-锰复合体或过渡相中可能存在锰；温度高于250℃时，随着过渡相变粗、溶解，锰信号消失，而铜信号增强，在350℃后铜信号达到饱和，温度为450℃左右时，稳定相形成. 关键词： 正电子湮没技术 空位-溶质复合体 沉淀 退火     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.     

A stereo matching algorithm using multi-peak candidate matches and geometric constraints

Gray cross correlation matching technique is adopted to extract candidate matches with gray cross correla- tion coefficients less than some certain range of maximal correlation coefficient called multi-peak candidate matches. Multi-peak candidates are extracted corresponding to three closest feature points at first. The corresponding multi-peak candidate matches are used to construct the model polygon. Correspondence is determined based on the local geometric relations between the three feature points and the multi-peak candidates. The disparity test and the global consistency checkout are applied to eliminate the remaining ambiguous matches that are not removed by the local geometric relational test. Experimental results show that the proposed algorithm is feasible and accurate.