Palladium catalyzed reductive homocoupling reactions of aromatic halides in dimethyl sulfoxide (DMSO) solution

Biaryls were obtained in good to excellent yields from the palladium catalyzed reductive homocoupling reactions of various aryl iodides and bromides in dimethyl sulfoxide (DMSO) solution without the need for any additional reducing reagents. Pd(dppf)Cl₂ is the most effective among the screened palladium catalysts for the homocoupling reactions. Fluorides, carbonates, acetates and hydroxides can be used as bases at promoting the palladium catalyzed reductive homocoupling of aryl halides in DMSO solution. X-ray photoelectron spectroscopic (XPS) analysis shows that the oxidative Pd²⁺(dppf) species can be reduced into the Pd⁰(dppf) active species by solvent DMSO molecules to furnish the catalytic cycle, indicating that DMSO plays a dual role as both solvent and reducing reagent. A plausible reaction mechanism has been discussed. Elimination of additional reducing reagents will not only reduce the reaction operation cost, but will also simplify the product separation and purification.     

Efficient palladium-catalyzed homocoupling reaction and Sonogashira cross-coupling reaction of terminal alkynes under aerobic conditions

An efficient method for palladium-catalyzed homocoupling reaction of terminal alkynes in the synthesis of symmetric diynes is presented. The results showed that both Pd(OAc)(2) and CuI played crucial roles in the reaction. In the presence of 2 mol % Pd(OAc)(2), 2 mol % CuI, 3 equiv of Dabco, and air, homocoupling of various terminal alkynes afforded the corresponding symmetrical diynes in moderate to excellent yields, whereas low yields were obtained without either Pd(OAc)(2) or CuI. Moreover, high TONs (turnover numbers; up to 940 000 for the reaction of phenylacetylene) for the homocoupling reaction were observed. Under similar reaction conditions, cross-coupling of 1-iodo-4-nitrobenzene with phenylacetylene was also carried out smoothly in quantitative yield. However, the presence of CuI disfavored the palladium-catalyzed Sonogashira cross-coupling reactions of the less active aryl iodides and bromides. In the presence of 0.01-2 mol % Pd(OAc)(2), a number of aryl iodides and bromides were coupled with terminal alkynes in good to excellent yields. It is noteworthy that this protocol employs mild, efficient, aerobic, copper-free, and ligand-free conditions.     

Palladium-catalyzed cross-alkynylation of aryl bromides by sodium tetraalkynylaluminates

Sodium tetraalkynylaluminates (1-4), prepared from NaAlH4 and terminal alkynes, cross-couple with aryl bromides in the presence of Pd(0) and Pd(II) catalysts. The reactions take place in boiling THF or DME. The process is applicable to both homo- and heterocyclic aryl bromides and can be used for conversion of polybromo compounds into polyalkynes. The reactions are high yielding and selective, free of undesired homocoupling and hydrogenolysis processes. The reagents selectively react with the ring-bound bromine atoms but do not affect chloro, cyano, triflate, or ester functions.     

Evaluation of polymer-supported vinyltin reagents in the Stille cross-coupling reaction

The synthesis of two new vinyltin reagents grafted on an insoluble macroporous polymer is reported. These reagents were used in the palladium-catalyzed Stille cross-coupling reaction with aryl halides. In all reactions, the conversion of the starting aryl halide is high and the amount of organotin by-product is particularly low (at the end of the catalytic run, the amount of Sn is up to 16 ppm in the crude reaction mixture removed of the insoluble polymer, and it is less than 1 ppm in the product purified by chromatography on silica gel).     

A polystyrene-supported triflating reagent for the synthesis of aryl triflates

An insoluble polystyrene-supported triflating reagent has been prepared by suspension co-polymerization of N-(4-vinylphenyl)trifluoromethanesulphonimide, styrene and the JandaJel^® cross-linker. This reagent, in the presence of triethylamine, allows for the efficient synthesis of aryl triflates from a wide range of phenols in a process that permits the desired product to be isolated from the reaction mixture in essentially pure form via several filtration and concentration operations. Adding to the utility of this reagent is its ability to be easily recovered, regenerated and reused. Both soluble and insoluble bifunctional polymers containing trialkylamine moieties in addition to triflimide groups were also prepared and examined as triflating reagents. Unfortunately these reagents afforded only modest yields of the desired products in representative reactions.     

Ligand‐Promoted Oxidative Cross‐Coupling of Aryl Boronic Acids and Aryl Silanes by Palladium Catalysis

The first cross‐coupling reaction between aryl silanes and aryl boronic acids is described. This transformation represents one of the very few examples of coupling reactions between two nucleophilic organometallic reagents and provides a new method for the formation of biaryl compounds. The successful development of this reaction was enabled by the use of commercially available 2,2′‐bis(diphenylphosphino)‐1,1′‐binaphthyl (BINAP) as the ligand. A small amount of BINAP (3 mol %) was sufficient to suppress the formation of the homocoupling products, and the reaction yielded the cross‐coupling products with high selectivity under mild conditions, even when the ratio of the two coupling partners was 1:1.     

Quinonediimine‐Induced Oxidative Coupling of Organomagnesium Reagents

N,N′‐Diphenyl‐p‐benzoquinonediimine, a redox‐active unit of polyaniline, efficiently induced the oxidative homocoupling of various aryl‐ and vinylmagnesium reagents in suppressing the side reactions, such as 1,2‐ or 1,4‐addition reaction.     

N-picolinamides as ligands for Ullmann-type homocoupling reactions

The use of N-phenylpicolinamide (NPPA) as a ligand in Ullmann-type homocoupling reactions of aryl iodides and bromides in common solvents, such as DMF and MeCN has been successfully demonstrated at room temperature. In addition, this work provided the first example of the homocoupling of an aryl chloride at 82 °C, which is a relatively low temperature when compared to regular Ullmann reaction temperatures. Also, NPPA was successfully employed in base—and heat free Suzuki reactions, including electron rich and poor aryl halides with heteroarylboronic acids in moderate yields.     

CO2 as Both a Selective Agent and Reaction Media in Palla-dium-Catalyzed Reductive Ullmann-Type Coupling Reaction

Carbon dioxide as both a selective agent and reaction media in the palladium-catalyzed Ullmann-type coupling has been described. The results showed that aryl chlorides could be easily activated in the presence of carbon dioxide and the chemoselectivity shifted toward the palladium-catalyzed Ullmann-type coupling reaction. In liquid carbon dioxide, homocoupling reactions of aryl halides, including less reactive aryl chlorides, were carried out smoothly in moderate to good yields using Pd/C, zinc, and H2O as the catalytic system at room temperature.     

Nanosized Iron- or Copper-Catalyzed Homocoupling of Aryl,Heteroaryl, Benzyl,and Alkenyl Grignard Reagents

Under very mild reaction conditions, iron or copper nanoparticles efficiently promoted the homocoupling of different Grignard reagents in tetrahydrofuran at room temperature. The nanosized iron or copper particles were generated in situ in a simple and economical way from commercially available FeCl₂ or CuCl₂, respectively, an excess of lithium powder, and a catalytic amount (5 mol%) of 4,4′-di-tert-butylbiphenyl (DTBB) as electron carrier. The reaction of a series of aryl, heteroaryl, benzyl, and alkenyl Grignard reagents in the presence of a substoichiometric amount of the iron or copper nanoparticles led to the formation of the corresponding homocoupling products in good yield.     

Aryl‐aryl bonds formation in pyridine and diazine series. Diazines part 41

The synthesis of several symmetrical polyaromatic compounds with pyridine or diazine units has been achieved by homocoupling of aryl halides with Pd(OAc)₂ as catalyst. Cross‐coupling reactions of aryl Grignard reagents with Fe(acac)₃ as catalyst allowed the synthesis of various unsymmetrical polyaryl‐ or polyheteroaryl compounds with TTπ‐deficient rings.     

Diphenylphosphorylated PEG (DPPPEG) as a new support for generation of nano-Pd(0) as catalyst for carbon–carbon bond formation via copper-free Sonogashira and homocoupling reactions of aryl halides in PEG

In this study, synthesis and application of diphenylphosphorylated PEG₂₀₀ (DPPPEG₂₀₀) are described. Herein, we report a very simple procedure for the preparation of DPPPEG₂₀₀ as a stable solid through the reaction of PEG₂₀₀ with ClPPh₂. This compound was used as a very suitable ligand for the in situ generation of nano-Pd(0) particles through its reaction with PdCl₂ as a pre-catalyst. Isolation of this catalyst is very simple through addition of diethyl ether to the reaction mixture and centrifugations. Full characterization of the nano-Pd(0)/DPPPEG200 was performed by XRD spectra, UV–Vis spectra, and also by TEM image. This nano-complex was used as an efficient catalyst for copper-free Sonogashira and homocoupling reactions of aryl halides. The sonogashira reaction of aryl halides was conducted at 80 °C in PEG. However, the homocoupling reaction was performed at 100 °C for aryl iodides and activated aryl bromides and at 130 °C for deactivated aryl bromides and aryl chlorides in PEG. The catalyst was recovered and recycled for four consecutive runs.     

Synthesis, characterization and primary evaluation of the synthetic efficiency of supported vinyltins and allyltins

Supported vinyltins and allyltins grafted to an insoluble cross-linked polystyrene matrix were prepared using methods usually employed in solution, like hydrostannylation of alkynes, transmetallation of a tin halide with organomagnesium or organozinc reagents, and substitution of an allyl halide by a supported stannylanion or S_N2′ substitution of a supported β-stannylacrolein acetal by cyanocopper reagents in the presence of boron trifluoride etherate. The insoluble grafted organotin reagents were analysed by HRMAS NMR, allowing an unambiguous assignment of their isomeric distribution or the identification of side products. When involved in Stille cross-coupling reactions (vinyltins) or in addition on aldehydes (allyltins), these supported reagents exhibit similar reactivity and similar stereoselectivity when compared to the tributyltin analogues, with the advantage to prevent problems due to the contamination by tin residues.     

Gold‐Palladium Nanocluster Catalysts for Homocoupling: Electronic Structure and Interface Dynamics

The gold‐palladium (Au?Pd) bimetallic nanocluster (NC) catalyst in colloidal phase performs the homocoupling reaction of various aryl chlorides (Ar?Cl) under ambient conditions. We have systematically investigated various aspects of the Au?Pd NC catalysts with respect to this homocoupling reaction by using density functional theory (DFT) calculations, genetic algorithm (GA) approaches, and molecular dynamics (MD) simulations. Our findings include the geometric and electronic structures of the Au?Pd NC, the reactive Pd sites on the NC surface, the electron‐donating effects of surrounding polymer matrix, the reaction mechanism of homocoupling reaction and rate‐determining step, the inverse halogen dependence of the reaction, and the solvation dynamics at interface region between NC and polymer matrix in aqueous solution.     

Polymer-supported diimine molybdenum carbonyl complexes as highly reusable and efficient pre-catalysts in epoxidation of alkenes

By reaction of aldehydic polystyrene and ethylene diamine, polystyrene–imine–amine reagent was produced. Reaction of this reagent with benzaldehyde and 4-nitrobenzaldehyde resulted in polystyrene-diimines (3a and 3b). These reagents were used for the immobilization of molybdenum hexacarbonyl. The functionalized polystyrene and supported-diimine molybdenum carbonyl catalysts were characterized by FT-IR spectrum and CHN analysis. The molybdenum content of catalysts was determined by neutron activation analysis. Supported-diimine molybdenum carbonyl pre-catalysts (3aM and 3bM) were used in epoxidation of cyclooctene, and the reaction parameters such as solvent and oxidant were optimized and the epoxidation of different alkenes was investigated in optimizing these conditions. The obtained results in the presence of polymer-supported diimine molybdenum carbonyl pre-catalysts (3aM and 3bM) showed that they were very active and selective in the epoxidation of a wide range of alkenes. The reusability of the supported pre-catalysts was also studied. The results showed that they were highly reusable in epoxidation of alkenes.     

Design and synthesis of two epoxide derivatives from 3-ethynylaniline

For several years ago, several epoxide derivatives have been prepared using different methods; however, some protocols use reagents which could be expensive and require specials conditions. The aim of this investigation was to prepare two new epoxide-derivatives from 3-ethynylaniline using some reactions such as oximation, acetylation, 2 + 2 addition, functionalized chloroamides, and epoxidation via Darzens reaction. The chemical characteristics of epoxide derivatives were determinate through a spectroscopic and spectrometric analysis. In conclusion, it is noteworthy that the reactions used in this study do not involve expensive reagents or special conditions for the synthesis of epoxide derivatives.     

Selective diphosphorylation, dithiodiphosphorylation, triphosphorylation, and trithiotriphosphorylation of unprotected carbohydrates and nucleosides

[chemical reaction: see text]. Aminomethyl polystyrene resin-bound linkers of p-acetoxybenzyl alcohol were subjected to reactions with diphosphitylating and triphosphitylating reagents to yield the corresponding polymer-bound diphosphitylating and triphosphitylating reagents, respectively. A number of unprotected carbohydrates and nucleosides were reacted with the polymer-bound reagents. Oxidation with tert-butyl hydroperoxide or sulfurization with Beaucage's reagent, followed by removal of cyanoethoxy group with DBU and the acidic cleavage, respectively, afforded only one type of monosubstituted nucleoside and carbohydrate diphosphates, dithiodiphosphates, triphosphates, and trithiotriphosphates with high regioselectivity.     

Uncatalysed coupling of an activated aryl chloride with aryllithium and aryl Grignard reagents

Substitution of the chloro group in 2-(2-chlorophenyl)-4,4-dimethyl-2-oxazoline to afford biaryls occurs upon reaction with either aryllithium reagents or aryl Grignard reagents. The reactions with Grignard reagents occur under similar conditions to a previously reported manganese-catalysed procedure. The reactions with lithium reagents, whilst not always affording greater yields of product than the Grignard reagents, involve much shorter reaction times and afford yields, which are comparable with those obtained from the corresponding fluoro derivative.     

Copolymers of polystyrene—New polymer supports for asymmetric epoxidation of allylic alcohols

Tartrate‐functionalized polystyrene copolymers were prepared with divinyl benzene, tetraethyleneglycol diacrylate, and diallyl tartrate as the crosslinking agents. These insoluble materials possessed the unique advantages of heterogeneous reagents. These resins were used to support the asymmetric epoxidation of allylic alcohols along with titanium tetraisopropoxide and tert‐butyl hydroperoxide with reasonably good yields and a high enantiomeric excess. The swelling behavior and molecular architecture of the polymer backbone significantly influenced the effectiveness of the catalyst. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 161–169, 2000     

Unsymmetrical disulfide and sulfenamide synthesis via reactions of thiosulfonates with thiols or amines

The reactivity of thiosulfonates with nucleophilic reagents was investigated. When reactions of thiosulfonates with thiols were performed, unsymmetrical disulfides were obtained in excellent yields. This procedure could employ numerous aryl or alkyl thiols. On the other hand, reactions of thiosulfonates with amines proceeded in the presence of a copper catalyst. The procedure was performed efficiently in air, and afforded the corresponding sulfenamides.