基质辅助激光解析飞行时间质谱快速测定水解胶原蛋白粉分子量

应用基质辅助激光解析电离飞行时间质谱(MALDI-TOF-MS)快速测定了水解胶原蛋白粉的分子量.分别以α-氰基-4-羟基内桂酸、2,5-二羟基苯甲酸和芥子酸为基质,在正离子模式下对水解胶原蛋白粉分子质量分布进行测定.结果显示:芥子酸为最适宜基质,分析条件为线性方式和反射方式相结合,可准确、快速确定水解胶原蛋白粉的分子...     

香豆素类新基质在基质辅助激光解吸／电离飞行时间质谱测定多糖和糖蛋白中的应用

将几种香豆素类新基质(香豆素、3-羟基香豆素(3-HC)、3-氨基香豆素(3-AC)、3-羧基香豆素(3-CC)和4-甲基-7-羟基香豆素(4-M-7-HC))分别应用于基质辅助激光解吸/电离飞行时间质谱(MALDI TOF-MS)测定葡聚糖和3种糖蛋白的研究.香豆素和3-羟基香豆素分别与2,5-二羟基苯甲酸(DHB)混合组成2种二元基质,极大地改善了基质和葡聚糖样品的共结晶状况,样品分布更加均匀.葡聚糖样品更易解吸/电离,每个激光点照射样品均能产生较强的质谱信号,且谱图重现性更好,得到了理想的MALDI TOF-MS谱图.当香豆素类基质用于分析糖蛋白时:3-HC和4-M-7-HC是测定糖蛋白A的优异基质,能检测到m/z 为66 672 Da 的离子信号.而3-AC测定糖蛋白B的基质效果比糖类分析常用基质2,5-二羟基苯甲酸更好.因此,这些香豆素类化合物将为MALDI TOF-MS分析多糖和糖蛋白提供更多新基质选择.     

基质效应对有机磷农药测定的影响及其解决方法

该文以液液萃取-气相色谱法探讨了基质对乐果、甲基对硫磷、马拉硫磷和对硫磷4种有机磷测定的影响以及解决方法.研究表明,气相色谱法测定有机磷农药的过程中基质效应显著存在,其基质增强比例为1.01 ～3.46.基质效应由基质种类及含量、有机磷农药种类及浓度等因素决定,同时与萃取溶剂、测定条件(如衬管、进样口温度等)有关.不同萃取溶剂对有机磷农药的萃取效率不同,但均存在基质增强效应;当进样口温度为260 ℃时,可最大程度降低基质在衬管中的残留,且不造成有机磷农药的分解;衬管则应首选带玻璃棉的.实际样品/标准样品的交替进样方式可以降低基质效应强度,但难以达到回收率要求,而校正因子校正法及分析保护剂法则是降低或消除基质效应的可行办法.     

以滤纸为基质室温磷光法测定痕量多环芳烃的研究

1 前言 固体基质室温磷光法(SS-RTP)是一种发展很快的微量技术与痕量分析相结合的新技术.SS -RTP法以其简便、快速、灵敏的特点在环境污染物及药物分析方面得到了广泛的应用 [1],尤其对于痕量多环芳烃的分析十分有效.文献报道过应用环糊精诱导室温磷光法 [2]和胶束增稳室温磷光法[3]测定的方法.本文用国产快速定量滤纸作固体基质,探讨了测定萘、苊和屈磷光发光的条件,建立了以滤纸为基质的测定痕量萘、苊和屈的SS-RTP法.     

多元统计法分析镉在土壤基质灰褐牛肝菌系统中迁移的影响因素

灰褐牛肝菌(Boletus griseus)是可食用野生大型真菌,对土壤基质中的镉(Cd)有富集作用.为了探究Cd在土壤基质B.griseus系统中迁移的影响因素,本研究采集了云南省22个B.griseus样本及其对应的生长土壤基质,测定了菌体和土壤中总Cd含量及赋存形态、土壤基质的理化特性和矿物质元素含量水平,采用主...     

L-古洛糖酸γ-内酯对蔬菜中有机磷农药残留测定基质效应的补偿作用研究

建立了一种采用掩蔽试剂对有机磷农药残留测定时的基质效应进行补偿的方法.研究了其对仪器稳定性、耐受性的影响及对基质效应的补偿效果.结果显示,1.0 g/L的L-古洛糖酸γ-内酯对敏感农药甲胺磷、乙酰甲胺磷、氧乐果和久效磷的色谱行为改善显著,响应值分别提高了2.8、9.1、10.4和4.8倍,未对非敏感农药测定产生负面影响...     

激光解吸电离质谱新型液相基质研究

选用包括纳米粒子在内的多种基质化合物,构成了多种不同组成的液相基质.以多肽、蛋白、大环寡糖和有机小分子等数种类型化合物为样品,系统地考察了不同液相基质在基质辅助激光解吸电离飞行时间质谱(MALDI-TOF)分析中的应用情况,探讨了与固体制样方法的异同点.实验结果表明,有些液相基质对多类化合物具有较好的通用性,而有些液相基质对某些特定类型化合物的分析特别有效.     

基质固相分散气相色谱电子捕获检测器测定葡萄酒中5种农药残留

采用基质固相分散的样品前处理方法,替代传统的液-液萃取、固相萃取,从葡萄酒中提取、净化5种农药,气相色谱电子捕获检测器分析测定,基质匹配标准校正方法补偿基质效应。添加3水平(0.01-0.10mg/L)的回收率为85.7%-104.6%;相对标准偏差为3.6%-8.5%;检出限达到0.1-0.8μg/kg。本方法可用于葡萄酒样品中农药残留的测定。     

新型含氟基质在基质辅助激光解析电离飞行时间质谱法测定全氟磺酸中的应用北大核心CSCD

基于Witting反应,制备了可用于酸性小分子分析的新型基质1,1-二(3-氟苯基)乙烯(EDF),并通过核磁共振和质谱确认了EDF的结构.首先取适量EDF溶于二氯甲烷中,涡旋振荡5min,配制成1g·L^(-1)的EDF基质溶液;将食品级包装材料汉堡包装纸剪成0.5cm×0.5cm的碎片,取100.00mg在5mL甲醇中室温超声提取2h,过0.22μm滤膜,得到待测样品溶液.然后采用逐层点样的方法,移取0.6μL的EDF基质溶液快速点在不锈钢靶板圆点处,以二氯甲烷为溶剂的EDF基质溶液迅速挥干,因其沸点低以及移取的量少,正好覆盖圆点的范围,再移取0.8μL待测样品溶液点在不锈钢靶板的相同位置,待其自然挥干后,进行基质辅助激光解析电离飞行时间质谱(MALDI-TOFMS)分析,并对比了EDF与常用基质9-氨基吖啶(9-AA)、α-氰基-4-羟基肉桂酸(CHCA)以及1,6-二苯基-1,3,5-己三烯(DPH)对全氟辛烷磺酸(PFOS)和全氟丁烷磺酸(PFBS)的检测性能.结果表明,EDF可以达到和上述几种常见基质类似的信号强度,且背景更干净、几乎无基质干扰峰.以EDF为基质,以二十一烷酸为内标,建立的PFOS和PFBS标准曲线的线性范围均为20~250μg·L^(-1),检出限(3S/N)均为1μg·L^(-1).按标准加入法对实际包装纸样品进行回收试验,回收率为90.3%~108%,测定值的相对标准误差(n=7)在30%以内.说明该EDF基质检测结果较理想,适用于检测包装材料中的全氟磺酸.     

固体基质室温燐光猝灭法测定人发和水中痕量汞

基于水杨基荧光酮羧甲基纤维素铅发光分子微球(Pb(CMC)2-THBF)在滤纸基质上可发射强而稳定的室温燐光,由此建立了Pb(CMC)2-THBF固体基质室温燐猝灭测定痕量汞的新方法.Hg2 的含量在2.5~100.0(pg/mL)内与ΔIp值成线性关系,其线性回归方程为ΔIp=12.73 0.4699CHg2 (pg/mL),r=0.9991,检出限为3.2×10-13g/mL.该方法用于人发和水样中痕量汞的测定,结果满意.同时探讨了固体基质室温燐光猝灭测定痕量汞的机理.     

河水中兽药多残留分析时亲水亲脂平衡柱的基质效应和保留效果

基质效应是液相色谱-质谱联用(LC-MS)定量分析中的重要干扰因素。以反渗透水为空白对照进行LC-MS/MS检测,在500倍浓缩条件下考察了33种兽药分别经Waters、Supelco和CNW等3种亲水亲脂平衡(hydrophilic-lipophilic balance, HLB)固相萃取柱富集后的基质效应及其保留效果。结果表明,以反渗透水为基质时3种HLB柱均表现出外源性基质效应,对大部分喹诺酮类和四环素类兽药呈现促进效应,有两种HLB柱对雌激素类兽药等呈现抑制效应,对磺胺类兽药的基质效应不显著,有一种HLB柱对氯霉素类兽药呈现抑制效应;以河水为基质时,由于外源性杂质与内源性杂质共同作用,对大部分喹诺酮类和四环素类兽药呈现促进效应,对氯霉素类和雌激素类兽药呈现抑制效应,对磺胺类兽药基质效应不显著。与外标法相比较,基质匹配标准校正法可有效消除基质效应对检测结果的影响。在50 ng/L和200 ng/L两个加标水平下,Waters、Supelco和CNW 3种HLB柱对河水中33种目标兽药的校正后的回收率分别为40.3%~146.0%、37.8%~104.2%和52.9%~150.1%; RSD(n=4)为0.2%~14.6%。相同实验条件下3种HLB柱的外源性基质效应不容忽视。而采用基质匹配标准校正法克服目标物基质效应,保留效果无显著差异,富集效果良好,为河水样品中兽药多残留分析方法中固相萃取柱的选择提供了科学依据。     

Synthesis and Characterization of Lead Sulfide Nanoparticles in Zirconia-Silica-Urethane Thin Films Prepared by the Sol-Gel Process

PbS nanocrystals (NCs) ranging between 4–8 nm were incorporated into Zirconium-Silica-Urethane (ZSUR) matrix obtained by the sol-gel method. The sizes of the particles were controlled by temperature treatment and by concentration of PbS in ZSUR matrix. The sizes of PbS NCs were determined by TEM measurements. The quantum size effect could also be extracted from optical absorption and photoluminescence spectra. The new matrix allows incorporation of up to 40% PbS forming a characteristic structure of dendrite by reacting lead acetate with ammonium thiocyanate in sol-gel matrix. The sol precursors of the matrix for Zirconium-Silica-Urethane contained zirconium oxide (ZrO₂) matrix solution, tetramethoxysilane (TMOS), 3-glycid oxypropyl trimethoxysilane (GLYMO) and polyethylene urethane silane (PEUS) synthesized separately. The ZrO₂ matrix solution was obtained from zirconium n-tetrapropoxide in propanol and acetic acid was used as a chelating agent to stabilize the zirconium oxide precursor.     

Tackling matrix effects during development of a liquid chromatographic-electrospray ionisation tandem mass spectrometric analysis of nine basic pharmaceuticals in aqueous environmental samples

When developing an LC-MS/MS-method matrix effects are a major issue. The effect of co-eluting compounds arising from the matrix can result in signal enhancement or suppression. During method development much attention should be paid to diminish matrix effects as much as possible. The present work evaluates matrix effects from aqueous environmental samples in the simultaneous analysis of a group of nine specific pharmaceuticals with LC-ESI/MS/MS: flubendazole, propiconazole, pipamperone, cinnarizine, ketoconazole, miconazole, rabeprazole, itraconazole and domperidone. Solutions to diminish signal suppression were examined: optimisation of the sample preparation, decrease of the flow rate, and the use of appropriate internal standards. Several SPE-stationary phases were tested in view of retention of the analytes: Oasis HLB, C8, Phenyl, Strata X-polymer RP sorbent and Strata X-polymeric SCX/RP sorbent. Oasis HLB showed the best retention for all analytes. The Oasis HLB SPE-method was optimised, but analyses showed high matrix suppression. Therefore, a second SPE-method, on a phenyl stationary phase (the second best option), was also optimised. A comparison of the matrix effect was made between the two procedures: the phenyl-method was less subject to matrix effects, however, the average matrix effect (ME%) of 46% indicated that matrix effects where still present. Several optimisation options for the phenyl-method were evaluated: addition of a ferric nitrate solution before extraction, application of an alkaline wash step, and use of a second SPE-cartridge, either a NH2-column or a florisil column. A more efficient sample clean-up was achieved by applying the extract after extraction on the phenyl column and after dilution with chloroform, onto a NH2-column (average ME%: 53%). In addition, applying a post-column split (1:5), further reduced matrix effects (average ME%: 65%). Labelled internal standards are the best way to tackle matrix effects, but no such internal standards were commercially available for the analytes of interest. The thorough search and application of four internal standards (structural analogues) was beneficial and compensates the matrix effect partially (average ME%: 83%). In an attempt to reduce the analysis time Speedisk phenyl columns were applied. Under these conditions matrix effects decreased even more while recoveries were between 91 and 109%. Different kinds of surface water samples were analyzed, and different matrix effects were observed. For this reason, standard addition will be used to perform quantitative analysis.     

Novel matrix strategies for improved ionization and spatial resolution using IR-MALDESI mass spectrometry imaging

In mass spectrometry imaging (MSI) applications of infrared matrix-assisted laser desorption electrospray ionization (IR-MALDESI), an exogenous ice layer is the gold standard for an energy-absorbing matrix. However, the formation of the ice matrix requires additional time and instrument hardware, so glycerol was investigated herein as an alternative to the ice matrix to potentially improve spatial resolution and ionization, while decreasing experiment time. Glycerol solutions of varying concentrations were sprayed over top of rat liver tissue sections for analysis by IR-MALDESI and compared to the typical ice matrix condition. Additionally, we tested if combining the ice matrix and glycerol matrix would further improve analyses. Matrix conditions were evaluated by comparing ion abundance of six lipid species, the laser ablation spot diameter, and number of METASPACE annotations. The ion abundances were also normalized to the volume of tissue ablated to correct for lower abundance values due to less ablated tissue. It was observed that utilizing a 50% glycerol matrix without ice provides improved spatial resolution with lipid abundances and annotations comparable to the ice matrix standard, while decreasing the time required to complete an IR-MALDESI tissue imaging experiment.     

Preparation of starch-based biocomposites reinforced with mercerized lignocellulosic fibers: Evaluation of their thermal,morphological, mechanical,and biodegradable properties

In the present paper, starch-based biocomposites have been prepared by reinforcing corn starch matrix with mercerized Abelmoschus esculentus lignocellulosic fibers. The effect of fiber content on mechanical properties of composite was investigated and found that tensile strength, compressive strength, and flexural strength at optimum fiber content were 69.1%, 93.7% and 105.1% increased to that of cross-linked corn starch matrix, respectively. The corn starch matrix and its composites were characterized by Fourier transform infrared spectroscopy (FT-IR), Scanning electron microscopy (SEM), X-ray diffraction (XRD) and thermogravimetric (TGA) analysis. The fiber reinforced composites were found to be highly thermal stable as compared to natural corn starch and cross-linked corn starch matrix. Further, water uptake and biodegradation studies of matrix and composites have also been studied.     

Acetaminophen particle design using chitosan and a spray-drying technique

In this study matrices were prepared from particles of poorly water-soluble drugs such as acetaminophen (Act) to determine the drug release rate from these matrix particles. The matrix particles were prepared by incorporating drugs into chitosan powder (Cht, carrier) using a spray-drying method. The formation of composite particles was confirmed by scanning electron microscopic (SEM) analysis. The matrix particles prepared by spray-drying were spherical with a smooth surface. The crystallinity of acetaminophen in the composite particles was evaluated by powder X-ray diffraction and differential scanning calorimetry (DSC). The degree of crystallinity of acetaminophen in the matrix particles decreased with a reduction in the weight ratio of acetaminophen relative to the carrier. These results indicate that a solid dispersion of acetaminophen in chitosan forms matrix particles. The interaction between acetaminophen and chitosan was also investigated by FT-IR analysis. FT-IR spectroscopy of the acetaminophen solid dispersion suggested that the carbonyl group of acetaminophen and the amino group of chitosan formed a hydrogen bond. There were some differences at pH levels of 1.2 and 6.8 in the release of acetaminophen from the physical mixture compared to the matrix particles. At pH 1.2, the release from the matrix particles (Act : Cht=1 : 5) was more sustained than from the physical mixtures. The 70% release time, T70, of acetaminophen from the matrix particles (Act : Cht=1 : 5) increased in pH 1.2 fluid by about 9-fold and in pH 6.8 fluid by about 5-fold compared to crystalline acetaminophen. These results suggest that matrix particles prepared by spray-drying are useful as a sustained release preparation.     

氟化电热蒸发／电感耦合等离子体原子发射光谱中的基体效应研究

本文系统研究了氟化电热蒸发／电感耦合等离子体原子发射光谱（ＥＴＶ－ＩＣＰ－ＡＥＳ）测定难熔元素的基体效应。与常规气动雾化（ＰＮ）－ＩＣＰ－ＡＥＳ中的基体效应比较，氟化ＥＴＶ－ＩＣＰ－ＡＥＳ中的基体效应更小。对难熔基体元素，由于基体和待测元素与氟化剂之间的竞争反应，随着基体浓度的增加，待测元素谱线强度降低；对常见基体元素，由于热循环中基体与待测元素之间的选择挥发，对待测元素的蒸发和传输过程无明显影响     

二氧化钛纳米粒子-氧化石墨烯/聚酰亚胺混合基质膜的原位聚合及气体渗透性能

以钛酸四丁酯为前驱体,采用浸渍-沉淀法制备二氧化钛纳米粒子-氧化石墨烯(TiO_2-GO)复合物,再将TiO_2-GO复合物与4,4'-(六氟异亚丙基)邻苯二甲酸酐和4,4'-二氨基二苯醚通过原位聚合构建TiO_2-GO/TiO_2-GO/PI(聚酰亚胺)混合基质膜,用于CO_2的渗透脱除.采用傅里叶变换红外光谱(FTIR)、拉曼光谱(Raman)、透射电子显微镜(TEM)、扫描电子显微镜(SEM)、热失重(TG)和Zeta电位等表征了TiO_2-GO复合物和TiO_2-GO/PI混合基质膜的形貌与结构;探讨了TiO_2掺杂量对TiO_2-GO复合物及TiO_2-GO/PI混合基质膜的结构和气体渗透性能的影响.结果表明,TiO_2-GO复合物中TiO_2纳米粒子较均匀地沉积在GO片层上,TiO_2纳米粒子在形成的同时破坏了GO的结构,使其无序度增加.TiO_2的掺杂对TiO_2-GO/PI混合基质膜的形貌与结构影响较小,但提升了TiO_2-GO/PI混合基质膜的CO_2和N2渗透性能.但过量的掺杂使TiO_2粒子在GO片层上团聚,从而导致TiO_2-GO复合物在混合基质膜中的分散性变差,CO_2渗透性及CO_2/N2渗透选择性降低.当TiO_2掺杂质量分数为30%时,TiO_2-GO/PI混合基质膜的CO_2渗透性为360 Barrer[1 Barrer=10~(-10)cm~3(STP)·cm/(cm~2·s·cm Hg)=7.5×10~(-14)cm~3(STP)·cm/(cm~2·s·Pa)],CO_2/N_2的渗透选择性可达31.     

Incoherent production reactions of positive and negative ions in matrix-assisted laser desorption/ionization

Utilizing synchronized dual-polarity matrix-assisted laser desorption/ionization (MALDI) mass spectrometry, we found good evidence of the incoherent production of positive and negative matrix ions. Using thin, homogeneous 2,5-dehydroxybenzoic acid (DHB) matrix films, positive and negative matrix ions were found to appear at different threshold laser fluences. The presence of molecular matrix ions of single charge polarity suggests that the existence of DHB ion-pairs may not be a prerequisite in MALDI. Photoelectrons induced by the laser excitation may assist the production of negative DHB ions, as shown in experiments conducted with stainless steel and glass substrates. At high laser fluences, the relative yield of positive and negative matrix ions remained constant when homogeneous matrix films were used, but it fluctuated significantly with inhomogeneous crystal morphology. This result is also inconsistent with the hypothesis that matrix ion-pairs are essential primary ions. Evidence from both low and high laser fluences suggests that the productions of positive and negative matrix ions in MALDI may occur via independent pathways.