高效液相色谱-串联质谱法同时测定肉类罐头中双酚-二缩水甘油醚

建立了同时测定肉类罐头中双酚A-二缩水甘油醚(BADGE)、双酚F-二缩水甘油醚(BFDGE)及其衍生物双酚A-(2,3-二羟丙基)甘油醚(BADGE•H2O)、双酚A-双(2,3-二羟丙基)醚(BADGE•2H2O)、双酚A-(3-氯-2-羟丙基)(2,3-二羟丙基)醚(BADGE•H2O•HCl)、双酚A-(3-氯-2-羟丙基)甘油醚(BADGE•HCl)、双酚A-双(3-氯-2-羟丙基)醚(BADGE•2HCl)、双酚F-双(2,3-二羟丙基)醚(BFDGE•2H2O)、双酚F-双(3-氯-2-羟丙基)醚(BFDGE•2HCl)9种环境激素的高效液相色谱-串联质谱分析方法。样品经叔丁基甲醚提取,HLB固相萃取小柱净化,C18色谱柱分离,用5 mmol/L醋酸铵溶液(含0.1%甲酸)与甲醇为流动相梯度洗脱,质谱多反应监测(MRM)模式检测,基质标准校正,外标法定量。结果表明,这9种化合物在10.0～2000.0 μg/L范围内线性关系良好;定量限(以信噪比≥10计)为10.0 μg/kg;在高、中、低3个加标水平下9种化合物的平均添加回收率为79.6%～100.9%,相对标准偏差为6.3%～12.1%。该方法具有较高的灵敏度和准确度,能满足法规要求的对肉类罐头中双酚A-二缩水甘油醚、双酚F-二缩水甘油醚及其衍生物残留量的快速检测及准确定量。     

Determination of bisphenol A diglycidyl ether and its hydrolysis and chlorohydroxy derivatives by liquid chromatography-mass spectrometry

European Legislation establishes that the sum of the migration levels of bisphenol A diglycidyl ether (BADGE), its hydrolysis (BADGE.H2O and BADGE.2H2O) and chlorohydroxy (BADGE.HCl, BADGE.2HCl and BADGE.H2O.HCl) derivatives shall not exceed the limit of 1 mg/kg in foodstuffs or food simulants. A reversed-phase high-performance liquid chromatographic (RP-HPLC) method combined with mass spectrometry detection using atmospheric pressure chemical ionisation (APCI) is developed for the separation, quantification and identification of the interesting compounds. Quantification of the analytes was carried out in the single ion recording mode, once their characteristic masses were selected from their full spectra, by using an external calibration. The optimised method was suitable for the migration evaluation of these compounds in different samples.     

固相萃取-高效液相色谱-串联质谱测定水中8种双酚-二环氧甘油醚

建立了水中8种双酚-二环氧甘油醚（双酚A二缩水甘油醚（BADGE）及其衍生物双酚A（3-氯-2-羟丙基）甘油醚（BADGE·5HCl）、双酚A双（3-氯-2-羟丙基）醚（BADGE·52HCl）、双酚A（2,3-二羟丙基）甘油醚（BADGE·5H₂O）、双酚A双（2,3-二羟丙基）醚（BADGE·52H₂O）、双酚A（3-氯-2-羟丙基）（2,3-二羟丙基）醚（BADGE·5HCl·5H₂O）和双酚F-二环氧甘油醚（BFDGE）及其衍生物双酚F双（3-氯-2-羟丙基）醚（BFDGE·52HCl））的固相萃取-高效液相色谱-串联质谱（SPE-HPLC-MS/MS）测定方法。10个饮用水接触涂料样品在室温避光条件下,以超纯水浸泡（24±1）h,然后取200 mL经C₁₈固相萃取柱进行净化浓缩,以C₁₈色谱柱进行分离,以5 mmol/L醋酸铵、甲醇和水为流动相进行梯度洗脱,质谱多反应监测（MRM）模式检测,外标法定量。结果表明,8种双酚-二环氧甘油醚在0.007~5.00 μg/L线性关系良好,相关系数均大于0.9990,该方法对8种双酚-二环氧甘油醚的定量限为7~91 ng/L,回收率为79.1%~101%,RSD为4.0%~12%。该方法具有灵敏度高、选择性强的特点,能够满足水中双酚-二环氧甘油醚的快速检测和准确定量。     

多壁碳纳米管固相萃取-高效液相色谱-串联质谱法测定食品接触材料中双酚-二环氧甘油醚的迁移量

建立了测定食品接触材料中6种双酚-二环氧甘油醚(双酚A二缩水甘油醚(BADGE)及其衍生物双酚A(2,3-二羟丙基)甘油醚(BADGE•H2O)、双酚A(3-氯-2-羟丙基)甘油醚(BADGE•HCl)、双酚A(3-氯-2-羟丙基)(2,3-二羟丙基)醚(BADGE•H2O•HCl)和双酚F二缩水甘油醚(BFDGE)及其衍生物双酚F双(3-氯-2-羟丙基)甘油醚(BFDGE•2HCl))迁移到食品中的迁移量的高效液相色谱-串联质谱法(HPLC-MS/MS)。样品以叔丁基甲醚(MTBE)为提取溶剂,超声提取,提取液经多壁碳纳米管(MWCNTs)固相萃取(SPE)柱富集、净化。以COSMOSIL C18为分析柱,流动相为0.1%甲酸的5 mmol/L醋酸铵溶液和甲醇。6种双酚-二环氧甘油醚在1.0～100 μg/L范围内线性关系良好(r2＞0.9991)。在3个添加水平下,6种目标化合物的回收率范围为78.6%～89.9%,相对标准偏差小于10%。方法检出限范围为0.5～1.5 μg/L。该方法操作简单,灵敏度高,可应用于食品接触材料中双酚-二环氧甘油醚迁移量的快速检测。     

Analysis of pesticides in fruits by pressurized liquid extraction and liquid chromatography-ion trap-triple stage mass spectrometry

A multi-residue method using pressurized liquid extraction (PLE) and liquid chromatography-quadrupole ion trap-triple stage mass spectrometry (LC-IT-MS(3)) has been developed for determining trace levels of pesticides in fruits. The selected pesticides can be distinguished in: benzimidazoles and azoles, organophosphorus, carbamates, neonicotinoids, and acaricides. PLE has been optimized to extract these pesticide residues from oranges and peaches by studying the effect of experimental variables on PLE efficiency. Samples were extracted at high temperature and pressure (75 degrees C and 1500psi) using ethyl acetate as extraction solvent and acidic alumina as drying agent. The recoveries obtained by PLE ranged from 58% to 97% and the relative standard deviation (RSDs) from 5% to 19%. The limits of quantification (LOQs) of the compounds were from 0.025 to 0.25mgkg(-1), which are well-below the maximum residue limits (MRLs) established by the European Union (EU) and the Spanish legislations.     

Pressurized liquid extraction followed by high-performance liquid chromatography for determination of seven active compounds in Cortex Dictamni

A new method based on pressurized liquid extraction (PLE) followed by a sensitive and specific HPLC-DAD analysis is developed for determination of seven compounds in Cortex Dictamni. The operational parameters of PLE, such as extraction solvent, extraction temperature, extraction pressure, static extraction time, flush volume and extraction cycles were optimized, using the extraction efficiencies of dictamnine, obacunone and fraxinellone as targets. The optimized procedure employed MeOH as extraction solvent, 150 degrees C of extraction temperature, 1,500 psi extraction pressure, 5 min of static extraction time, 60% flush volume and the extraction recoveries of the three compounds were nearly to 100% for only one cycle. The following HPLC analysis was performed on a reversed-phase C(18) column with methanol-water as mobile phase in gradient manner, detected at 236 and 218 nm. The limits of detection (LOD) and limits of quantification (LOQ) of the seven compounds were in the range of 0.4-15.6 ng and 1.2-38.8 ng. This assay can be readily utilized as a quality control method for Cortex Dictamni and other related medicinal plants.     

Simultaneous determination of bisphenol-A-diglycidyl ether, bisphenol-F-diglycidyl ether, and their derivatives in oil-in-water and aqueous-based canned foods by high-performance liquid chromatography with fluorescence detection

A gradient reversed-phase liquid chromatography with fluorescence detection method for simultaneous identification and quantification of bisphenol-A-diglycidyl ether (BADGE), bisphenol-F-diglycidyl ether (BFDGE), and their 10 derivatives in food matrixes was developed and validated for the analysis of oil-in-water- and aqueous-based foodstuffs. The method linearity range 0.016-10 ppm which are hundred-fold below and tenfold above the EU restriction at 1 ppm (mg/kg). The method detection limits range 0.72-4.20 ppb and the method quantitation limits range 2.40-14.85 ppb, respectively. The validation data indicate excellent precision, acceptable recovery, and good robustness, all supporting a good potential to further develop the method as a standard method for the determination of migrations from interior can coatings into foodstuffs.     

Optimization of a pressurized liquid extraction method by experimental design methodologies for the determination of fluoroquinolone residues in infant foods by liquid chromatography

In the present study, we have developed a method based on pressurized liquid extraction (PLE) and liquid chromatography with fluorescence detection (LC-FLD) for the determination of residues of fluoroquinolones (FQs) in infant food products. PLE extraction has been optimized by the application of experimental design methodologies. Initially, a fractional factorial design (FFD) was used to screen the significance of four extraction parameters: solvent composition, temperature, pressure and number of cycles. The most significant factors, identified by ANOVA analysis, were the solvent composition, temperature and pressure, which were further optimized with the aid of a face centred design (FCD) and the desirability function. The optimized operating PLE conditions were as follows: ACN/o-phosphoric acid 50 mM pH 3.0 (80:20, v/v), 80 °C, 2000 psi and three extraction cycles of 5 min. Under these conditions, recoveries of the target FQs varied between 69% and 107% with RSDs below 9%. The whole method was validated according to the Commission Decision 2002/657/EC guidelines. The proposed method has been successfully applied to the analysis of different infant food products bought in local supermarkets and pharmacies. The results showed the presence of residues of enrofloxacin in a non-compliant baby food sample corresponding to a chicken-based formulation, which were also confirmed and quantified by LC–MS/MS analysis.     

Simultaneous determination of ergosterol, nucleosides and their bases from natural and cultured Cordyceps by pressurised liquid extraction and high-performance liquid chromatography

A simple method is described for the simultaneous determination of ergosterol, nucleosides and their bases in Cordyceps. The samples were extracted by using pressurised liquid extraction (PLE). The effects of experimental variables, such as solvent, temperature, static extraction time and cycles, on PLE efficiency have been studied. The results showed a strong influence of the solvent and temperature on extraction efficiency of PLE. The determination was achieved by high-performance liquid chromatography (HPLC) using a Zorbax NH2 analytical column (250 x 4.6 mm i.d., 5 microm) with diode-array detector (DAD). The automated preparation of the sample permits a very fast analysis which is an important goal for routine purpose.     

Fast liquid chromatography-tandem mass spectrometry for the analysis of bisphenol A-diglycidyl ether, bisphenol F-diglycidyl ether and their derivatives in canned food and beverages

In this work a fast liquid chromatography coupled with tandem mass spectrometry (LC–MS/MS) method using a C18 Fused Core™ column, was developed for the simultaneous analysis of bisphenol A diglycidyl ether (BADGE), bisphenol A (2,3-dihydroxypropyl) glycidyl ether (BADGE·H₂O), bisphenol A bis(2,3-dihydroxypropyl) ether (BADGE·2H₂O), bisphenol A (3-chloro-2-hydroxypropyl) glycidyl ether (BADGE·HCl), bisphenol A bis(3-chloro-2-hydroxypropyl) ether (BADGE·2HCl) and bisphenol A (3-chloro-2-hydroxypropyl)(2,3-dihydroxypropyl ether) (BADGE·HCl·H₂O) and bisphenol F diglycidyl ether (BFDGE), bisphenol F bis(2,3-dihydroxypropyl) ether (BFDGE·2H₂O), bisphenol F bis(3-chloro-2-hydroxypropyl) ether (BFDGE·2HCl). The LC method was coupled with a triple quadrupole mass spectrometer, using an ESI source in positive mode and using the [M+NH₄]⁺ adduct as precursor ion for tandem mass spectrometry experiments. The method developed was applied to the determination of these compounds in canned soft drinks and canned food. OASIS HLB solid phase extraction (SPE) cartridges were used for the analysis of soft drinks, while solid canned food was extracted with ethyl acetate. Method limits of quantitation ranged from 0.13 μg L⁻¹ to 1.6 μg L⁻¹ in soft drinks and 1.0 μg kg⁻¹ to 4.0 μg kg⁻¹ in food samples. BADGE·2H₂O was detected in all the analyzed samples, while other BADGEs such as BADGE·H₂O, BADGE·HCl·H₂O, BADGE·HCl and BADGE·2HCl were also detected in canned foods.     

Extraction and analysis of ochratoxin A in bread using pressurised liquid extraction and liquid chromatography

A pressurised liquid extraction (PLE) method for the analysis of ochratoxin A (OTA) in bread samples is given. Parameters such as solvent, temperature, pressure and time were investigated thoroughly. The optimized PLE conditions were: methanol as extraction solvent, 80 degrees C, 2000 psi and a 5-min cycle. OTA was determined by liquid chromatography coupled with fluorescence detection and confirmed by methyl ester derivatization. Under these conditions OTA recovery is 92.3% with a RSD of 5%. Limits of detection and quantification were 0.02 and 0.06 microg/kg, respectively. The proposed method was applied to 20 bread samples, finding two positive samples with OTA levels below the maximum permitted levels by the European Union.     

Multiple-stage mass spectrometry analysis of bisphenol A diglycidyl ether, bisphenol F diglycidyl ether and their derivatives

The fragmentation of bisphenol A diglycidyl ether (BADGE), bisphenol F diglycidyl ether (BFDGE) and their derivatives was studied by electrospray ionization tandem mass spectrometry. Multiple-stage mass spectrometry and accurate mass measurements were combined to establish the fragmentation pathways. BADGEs and BFDGEs tend to form ammonium adducts under electrospray conditions which fragmented easily. The fragmentation of [M+NH(4)](+) for BADGEs started with the cleavage of the phenyl-alkyl bond, which was followed by the α-cleavage of the ether group to generate the characteristic product ions at m/z 135, [C(9)H(11)O](+), and m/z 107, [C(7)H(7)O](+). The fragmentation of the BFDGE isomer mixtures was studied by on-line reversed-phase liquid chromatography coupled to multiple-stage mass spectrometry (LC/MS(n)). Information obtained from product ion spectra for each BFDGE isomer and its comparison with the fragmentation pathway of BADGE allowed each isomer and the chromatographic elution order to be identified.     

Simultaneous determination of fluoroquinolones,sulfonamides and tetracyclines in sewage sludge by pressurized liquid extraction and liquid chromatography electrospray ionization-mass spectrometry

A new scheme for the quantitative determination of traces of fluoroquinolones (FQs), tetracyclines (TCs) and sulfonamides (SAs) in sewage sludge was developed. The compounds were simultaneously extracted from sewage sludge by pressurized liquid extraction (PLE). A novel and effective method for PLE was developed. Solid-phase extraction was used for cleaning up the extracts. Identification and quantification of the compounds was done using high-performance liquid chromatography with electrospray ionization mass spectrometry in selected reaction monitoring mode. The best recovery of FQs and TCs was obtained by using hydrophilic–lipophilic balance cartridges, recoveries ranged 59% for norfloxacin to 82% for ofloxacin and 95% for doxycycline; for SAs strong cation-exchange cartridges were more efficient, recoveries were 96% for sulfamethoxazole and 43% for sulfadimethoxine. Limit of quantification ranged from 0.1 ng/g for SAs to 160 ng/g for tetracycline. Method precision for TCs was 5.06% and 1.12%, and for SAs 0.43% and 2.01%. FQs precision ranged from 0.77% to 1.89%.     

Quantification of derivatives of bisphenol A diglycidyl ether (BADGE) and novolac glycidyl ether (NOGE) migrated from can coatings into tuna by HPLC/fluorescence and MS detection

A reversed phase high performance liquid chromatographic method combined with fluorescence and mass spectrometric detection in series is presented for the separation and quantification of bisphenol A diglycidyl ether (BADGE) and novolac glycidyl ether (NOGE) derivatives in extracts from food can coatings, tuna and oil. Fifteen samples of tuna cans bought in four European countries were investigated. Atmospheric pressure chemical ionization mass spectrometry in the positive ion mode (APCI(+)-MS) allowed to tentatively identify BADGE and NOGE related compounds originating from reactions of the glycidyl ethers with bisphenols, phenol, butanol, water and hydrochloric acid. Quantification was based on the external standard method and fluorescence detection. Mass fractions up to 3.7 micrograms/g were found for hydrochlorination products of bisphenol F diglycidyl ether (BFDGE + 2HCl) in tuna. Furthermore, total migration quantities of phenolic ether compounds were estimated. The highest values found were 20 micrograms/g in tuna and 43 micrograms/g in the oil phase.     

Pressurised liquid extraction of flavonoids in onions. Method development and validation

A rapid and reliable analytical method for quantification of flavonoids in onions was developed and validated. Five extraction methods were tested on freeze-dried onions and subsequently high performance liquid chromatography (HPLC) with UV detection was used for quantification of seven flavonoids.The extraction efficiencies were lowest for the conventional water bath extraction compared to pressurized liquid extraction (PLE), ultrasonication, ultrasonic liquid processor, and microwave extraction, which yielded similar efficiencies. The reproducibility was in the same range (RSD: 1-11%) for all tested extraction methods. However, PLE was the preferred extraction method because the method can be highly automated, use only small amounts of solvents, provide the cleanest extracts, and allow the extraction of light and oxygen-sensitive flavonoids to be carried out in an inert atmosphere protected from light.The method parameters: extraction temperature, sample weight, flush volume and solvent type were optimised, and a clean-up step was integrated in the PLE procedure by in-cell addition of C18-material to the extraction cells, which slightly improved the recovery and reproducibility of the method. The one-step PLE method showed good selectivity, precision (RSDs = 3.1-11%) and recovery of the extractable flavonoids (98-99%). The method also appeared to be a multi-method, i.e. generally applicable to, e.g. phenolic acids in potatoes and carrots.     

Comparison of ultrasonic and pressurized liquid extraction for the analysis of polycyclic aromatic compounds in soil samples by gas chromatography coupled to tandem mass spectrometry

A pressurized liquid extraction (PLE) method has been optimized for the determination of polycyclic aromatic hydrocarbons (PAHs) in soil samples and it was compared with ultrasonic extraction. The extraction step was followed by gas chromatography-triple quadrupole mass spectrometry (GC-QqQ-MS/MS) analysis. Parameters such as type of solvent, extraction time, extraction temperature and number of extractions were optimized. There were no significant differences among the two extraction methods although better extraction efficiencies were obtained when PLE was used, minimizing extraction time and solvent consumption. PLE procedure was validated, obtaining limits of detection (LODs) ranging from 0.02 to 0.75 μg kg⁻¹ and limits of quantification (LOQs) ranging from 0.07 to 2.50 μg kg⁻¹ for the selected PAHs. Recoveries were in the range of 59-110%, except for naphthalene, which was the most volatile PAH. Finally, the method was applied to real soil samples from Southeast of Spain. PAHs concentrations were low, and phenanthrene, pyrene, fluorene, benzo[a]pyrene and chrysene were the most frequently detected analytes in the samples.     

Pressurized Liquid Extraction Combined with Dispersive Liquid‐liquid Micro‐extraction as an Efficient Sample Preparation Method for Determination of Volatile Components in Tobacco

The pressurized liquid extraction (PLE) followed by dispersive liquid–liquid micro‐extraction (DLLME) has been developed for extraction of volatile components in tobacco. 35 volatile components were detected by gas chromatography mass spectrometry (GC‐MS). Methanol–methyl tert‐butyl ether (MTBE) (8:2, v/v) was selected as PLE extraction solvent. The optimized DLLME procedure, 3 mL of pure water and 1.0 mL tobacco extract solution, 40 μL of chloroform as extraction solvent, 0.5 mL of acetonitrile as disperser solvent, was validated. Under the optimum conditions, the enrichment factors were in the range of 96‐159. The limits of detection were between 0.14 and 0.33 μg/kg. The repeatability of the proposed method, expressed as relative standard deviation, varied between 4.3 and 7.5% (n = 6). The recoveries of the analytes evaluated by fortification of tobacco samples were in the range of 84.7‐96.4%. Compared with the conventional sample preparation method for determination of volatile components in tobacco, the proposed method was quick and easy to operate, and had high‐enrichment factors and low consumption of organic solvent.     

Simultaneous determination of anthraquinones in Rhubarb by pressurized liquid extraction and capillary zone electrophoresis

Rhubarb, a well-known Chinese herbal medicine, is also used in Europe and other places of the world. Anthraquinones derivatives are thought to be the major active components. A pressurized liquid extraction (PLE) and capillary zone electrophoresis (CZE) separation were developed for simultaneous determination of five anthraquinones including aloe-emodin, emodin, chrysophanol, physcion, and rhein in Rhubarb. The effects of the experimental variables on PLE and CZE have been optimized. The optimum conditions of PLE were: solvent, methanol; temperature, 140 degrees C; particle size, 0.13-0.2 mm; static extraction time, 5 min; pressure, 1500 psi; and one extraction. The best separation of the five anthraquinones could be obtained using 50 mM borate buffer (pH 8.2) containing 25% isopropyl alcohol and 25% acetontrile as modifier, while the separation voltage was 25 kV and the temperature was at 20 degrees C. The method developed is accurate, simple, and reproducible, and could be used for quality control of Rhubarb and its medical preparations.     

Determination of pesticides in milk-based infant formulas by pressurized liquid extraction followed by gas chromatography tandem mass spectrometry

An efficient and selective automated analytical method for the determination and quantification of a selected group of 12 organochlorine and organophosphorous pesticides in milk-based infant formulas has been developed. The samples were extracted by pressurized liquid extraction (PLE) and analysed using GC-MS/MS. The use of alumina as the fat retainer in the PLE extraction cell, together with the application of an injector temperature program during the GC injection process, avoided typical matrix interferences without the application of additional cleanup steps. Mean recoveries of between 70 and 110% were achieved for most of the compounds, except for chlorpyrifos methyl (50%), vinclozoline (48%), fenitrothion (56%) and procymidone (53%), with relative standard deviations ranging from 9 to 17%. Low limits of quantification were obtained for the studied compounds, from 0.01 to 2.6 μg kg⁻¹, thus guaranteeing their accurate determination within the rigorous requirements established for baby food. The validated method was applied to a pilot monitoring study in Spain. Twenty five samples of different brands of powdered infant formulas were obtained from supermarkets. Positive findings of endosulfan I, endosulfan II, fenitrothion, chlorpyrifos ethyl and bifenthrin were detected at concentrations ranging from 0.03 to 5.03 μg kg⁻¹.     

Pressurized liquid extraction and liquid chromatography–tandem mass spectrometry applied to determine iodinated X-ray contrast media in sewage sludge

Pressurized liquid extraction (PLE) has been successfully applied for the first time to the extraction of five iodinated X-ray contrast media from sludge. Once optimized all PLE parameters, the extract has been analyzed by liquid chromatography–tandem mass spectrometry, being the method developed sensible enough to reach limit of quantifications (LOQs) of 25 μg kg⁻¹ (d.w.). The developed method has been applied to the analysis of sludge from urban sewage treatment plants and although some compounds such as iopromide, diatrizoic acid and iopamidol have been identified, their concentrations have been lower than their LOQs.