SiO2交联剂交联MMA聚合制备PMMA/SiO2纳米复合材料

用SiO2交联剂(SiO2HPA)交联甲基丙烯酸甲酯(MMA)自由基聚合制备PMMA SiO2纳米复合材料。采用两步法将可聚合乙烯基单体以化学键的形式键接到SiO2表面合成SiO2交联剂,首先利用过量的甲苯2,4二异氰酸酯(TDI)对SiO2纳米粒子表面进行化学修饰合成出表面带有高反应活性NCO基团的功能化SiO2粒子(SiO2TDI),SiO2TDI与丙烯酸羟丙酯(HPA)反应合成SiO2交联剂。系统研究了MMA单体与SiO2交联剂投料比及聚合时间对聚合反应的影响。此外,利用红外光谱(FT IR)、DSC、TGA、可见光光谱仪等实验手段对纳米复合材料进行了表征分析。结果表明,纳米SiO2粒子在复合材料中起着物理交联点和化学交联点作用,复合材料玻璃化转变温度(Tg)明显地高于其纯PMMA的玻璃化转变温度,随着纳米SiO2粒子含量的增加,复合材料玻璃化温度升高,而透明度明显降低。     

MMA接枝改性PVC/CaCO3纳米复合材料的力学性能

采用熔融共混法制备PMMA接枝改性纳米CaCO3增韧PVC（PVC/CaCO3）复合材料,并研究了复合材料的力学性能.结果表明,通过表面PMMA的接枝改性,可以显著提高纳米CaCO3增韧聚氯乙烯复合材料的拉伸强度和拉伸模量,在纳米CaCO3颗粒表面PMMA包覆层厚度为2nm时,复合材料的拉伸强度和拉伸模量达到极大值.对比于未处理纳米CaCO3和钛酸酯偶联剂处理纳米CaCO3,PMMA接枝改性纳米CaCO3增韧PVC复合材料的拉伸强度得到较大幅度提高.SEM显示,经过PMMA接枝改性后的碳酸钙在PVC基体中分散均匀,与基体界面结合良好.     

PP/EPDM/CaCO3三元复合材料的相结构及力学性能研究

采用以化学键合方式在CaCO3表面包覆上聚丙烯蜡和将改性后的CaCO3先与EPDM复合、再与PP复合的工艺,制备PP/EPDM/CaCO3三元复合材料,以期在PP基体材料中得到EPDM包裹CaCO3的相结构.通过测量三元复合体系中各组分的表面张力,计算各可能组分对之间的界面张力和黏结功,分析三元复合体系中可能的相结构.热力学计算结果表明,三元复合体系中既存在以EPDM为壳、CaCO3为核的"核壳结构",又存在CaCO3与EPDM各自独立分散在PP基体中的结构.电镜照片进一步揭示,在PP/EPDM/改性CaCO3三元复合体系与PP/EPDM/未改性CaCO3三元复合体系中,这两种相结构的比例是不同的,在前者中以核壳结构为主.CaCO3表面性质的不同是产生这一差别的原因.由于这一结构差别的存在,PP/EPDM/改性CaCO3三元复合体系比PP/EPDM/未改性CaCO3三元复合体系具有更好的力学性能.当EPDM用量为8 phr、改性CaCO3用量为15 phr时,三元复合体系的冲击强度达14.25 kJ/m2,是纯PP的3.17倍.     

MC尼龙-纳米La2O3复合材料的制备及性能研究

用原位分散聚合法制备了一系列MC尼龙／纳米La2O3复合材料，研究了纳米La2O3用量对复合材料力学性能的影响，用SEM观察了La2O3粒子在MC尼龙基体中的分散情况，用XRD对复合材料的晶体结构进行了表征。SEM观察结果表明，当纳米La2O3用量小于1％时，纳米La2O3均匀分散于MC尼龙基体中，团聚情况很少，当纳米La2O3用量大于1％时，纳米La2O3开始团聚；XRD研究结果表明，纳米La2O3没有改变MC尼龙的结晶形态；力学性能的研究结果表明，随着纳米La2O3用量的增加，复合材料的拉伸强度、断裂伸长率、缺口冲击强度、弯曲强度和弯曲模量都呈先升后降的趋势，当纳米La2O3用量为0．5％时，复合材料的拉伸强度和断裂伸长率达到最大值，分别比MC尼龙提高17．9％和52．1％，当纳米La2O3的用量为1．0％时，复合材料的缺口冲击强度、弯曲强度和弯曲模量达到最大值，分别比MC尼龙基体提高36，6％．12．7％和16．3％。     

双马来酰亚胺树脂/SiO_2纳米复合材料的制备及性能

以表面含有胺基官能团的纳米SiO_2为填料,通过一步原位聚合法制备双马来酰亚胺树脂/SiO_2纳米复合材料(BMI/SiO_2).采用热重分析仪(TGA)、红外光谱分析仪(FTIR)、邵氏D硬度计(H)等仪器设备对BMI/SiO_2纳米复合材料进行测试分析,探讨纳米SiO_2对双马来酰亚胺聚酯树脂的热稳定性能、硬度和界面强度的影响.结果表明,所制备的BMI/SiO_2纳米复合材料的硬度随加入的纳米SiO_2含量的增加,呈现逐渐升高趋势.当纳米SiO_2含量为3%时,相对于双马来酰亚胺聚酯,复合材料的硬度提高了80%.通过热稳定性分析可知,纳米SiO_2的加入降低了双马来酰亚胺树脂基体材料的热分解温度,使其从458℃降低到451℃.通过对双马来酰亚胺/SiO_2纳米复合材料的界面分析发现,纳米SiO_2的表面接枝了双马来酰亚胺分子链,说明纳米SiO_2参与了双马来酰亚胺的聚合过程,有利于提高聚合物基体材料与填料间的界面强度,进而提高复合材料的机械性能.     

PMMA／石墨导电复合材料的制备与表征

以可膨化石墨为原料,高温处理得到膨化石墨,再经过超声处理,得到纳米薄片石墨。将得到的纳米薄片石墨与甲基丙烯酸甲酯单体在超声作用下预聚,灌模,得到块状的聚甲基丙烯酸甲酯(PMMA)/石墨复合材料。用扫描电子显微镜(SEM)、透射电子显微镜(TEM)、选区电子衍射SAD、红外、热重等分析仪器表征了纳米石墨薄片及PMMA/石墨复合材料。测试了复合材料的力学、电学性能,发现在室温下该复合材料的渗滤阀值为1.3%(wt),且保证石墨含量在1.4%(wt)时,即可保证复合材料具有良好的电学和力学性能。     

纳米Sb_2O_3表面原位(共)聚合处理对HIPS纳米复合材料力学性能的影响

通用高分子材料的工程化和工程高分子材料的高性能化是高分子材料研究与开发的主要方向之一，核心、关键技术是高分子材料的同时增强、增韧，其中利用纳米无机刚性粒子与高分子材料复合是一条最简单而又行之有效的途径．由于无机纳米填料是亲水性的、表面能极高，有机高分子不能浸润填料或与填料表面相互作用弱，导致纳米粒子在高分子基体中易于团聚而分散性差，其复合材料力学性能低下．利用硬酯酸、非离子表面活性剂、表面辐照接枝处理纳米粒子表面忙，     

聚丙烯/凹凸棒石纳米复合材料的制备与性能研究

以聚丙烯(PP)为聚合物基体,天然凹凸棒石(ATP)为无机组分,经过氧化聚乙烯对ATP表面进行包覆处理,用熔融共混的方法制备了PP/ATP纳米复合材料.扫描电镜结果显示,经本方法处理后的ATP在PP基体中分散较为均匀.ATP棒晶簇直径最佳分散尺寸能达到20~40 nm,比未处理ATP在基体中的棒晶簇直径小10 nm以上;XRD测试表明,未处理ATP和处理后的ATP均有使PP晶粒细化的作用,同时不改变PP的α晶型;DSC结果显示,ATP的加入提高了PP的结晶温度和结晶度,说明ATP有一定的成核作用.通过对复合材料的力学性能测试发现,经过处理的ATP制备的复合材料力学性能优于未处理ATP复合材料对PP力学性能的改善.其中ATP与氧化聚乙烯固含量的质量比为2∶1,ATP含量为3 wt%时复合材料力学性能达到最好.缺口冲击强度比纯PP最高提高了83%,提高幅度显著;经过处理的ATP制备的复合材料拉伸强度提高了6%~11%;弯曲强度提高了33%~45%;弯曲模量提高了90%~106%.     

Li3PO4纳米晶与Li3PO4/PMMA块体透明纳米复合材料的制备及性能研究

通过高温溶剂法制备了油酸包覆的Li3PO4纳米晶,经过聚乙二醇单油酸酯再修饰,分散于甲基丙烯酸甲酯单体中,通过原位紫外光引发本体聚合,得到了块体的Li3PO4/PMMA纳米复合材料.XRD谱显示所制备的Li3PO4纳米晶为纯的单斜相,而复合材料的XRD谱中含有Li3PO4的相,表明Li3PO4纳米晶已成功复合进PMMA中,Li3PO4的TEM显示其粒径较为均一,约为10 nm,且在环己烷中无明显的团聚.复合材料超薄切片的TEM表明,Li3PO4纳米晶以50 nm左右的团簇分散于聚合物基质中.FTIR测试表明制备的Li3PO4纳米晶被油酸包覆.UV-Vis显示当所制备的复合材料固含量达14.6 wt%仍然保持很高的透过率,TGA分析表明纳米粉的掺入使复合材料的分解温度提高了95℃.制备的Li3PO4/PMMA纳米复合材料有望应用于热中子的探测.     

PMMA Based Nanocomposites Filled with Modified CaCO3 Nanoparticles

PMMA based nanocomposites filled with calcium carbonate nanoparticles (CaCO₃) have been prepared by in situ polymerization approach. In order to improve inorganic nanofillers/polymer compatibility, PBA chains have been grafted onto CaCO₃ nanoparticle surface. Morphological analysis performed on nanocomposite fractured surfaces has revealed that the CaCO₃ modification induces homogeneous and fine dispersion of nanoparticles into PMMA as well as strong interfacial adhesion between the two phases. Mechanical tests have shown that both unmodified and modified CaCO₃ are responsible for an increase of the Young's Modulus, whereas only PBA-grafted nanoparticles allow to keep unchanged impact strength, strongly deteriorated by adding unmodified CaCO₃. Finally, the presence of CaCO₃ nanoparticles significantly improves the abrasion resistance of PMMA also modifying its wear mechanism.     

iPP Based Nanocomposites Filled with Calcium Carbonate Nanoparticles: Structure/Properties Relationships

Isotactic polypropylene (iPP) based nanocomposites filled with calcium carbonate nanoparticles (CaCO₃) were prepared by melt mixing and structure-properties relationships of the nanomaterials were studied. Elongated CaCO₃ nanopowders coated with two different coating agents, polypropylene-maleic anhydride graft copolymer (iPP-g-MA) and fatty acids (FA), were tested as nanoreinforced phases. The influence of surface treatment of the nanoparticles on the polymer/nanofillers interfacial adhesion and on the final materials properties was investigated. Morphological analysis showed that the selected coating agents induce different iPP/nanofiller adhesion degrees. Young's modulus increases as a function of the nanoparticles content and the coating agent nature. Finally, all the prepared nanocomposites showed a significant improvement of iPP barrier properties either to oxygen or to carbon dioxide.     

Ethylene-Octene Copolymer-Nanosilica Nanocomposites: Effects of Epoxy Resin Functionalized Nanosilica on Morphology,Mechanical, Dynamic Mechanical and Thermal Properties

A comparative study of the structural, thermal, mechanical and thermomechanical properties of ethylene-octene copolymer 1

1 Ethylene-octene copolymer is produced using Dow's INSITETM ™ constrained geometry catalyst and process technology. ENGAGE the trade name of this copolymer.

(mPE) 2

2 This copolymer will be represented as mPE .

nanocomposites synthesized with pure nanosilica (NS) and nanosilica-functionalized with diglycidyl ether of bisphenol-A (ENS) has been reported. These nanocomposites were prepared using “melt mixing” method at a constant loading level of 2.5 wt. %. The effects of pure nanosilica (NS) and epoxy resin-functionalized-nanosilica (ENS) on the above mentioned properties of ethylene-octene copolymer were analyzed by wide-angle-x-ray diffractometer (WAXD), transmission electron microscope (TEM), thermo gravimetric analyzer (TGA), differential scanning calorimeter (DSC), dynamic mechanical analyzer (DMA) and scanning electron microscope (SEM). TEM studies have shown a better dispersion of nanoparticles in case of ethylene-octene copolymer-epoxy resin-functionalized-nanosilica nanocomposite (mPE-ENS) than that of ethylene-octene copolymer-nanosilica nanocomposite (mPE-NS). The tensile tests show that organic modification of nanosilica particles brings up an appreciable increase in yield strength, ultimate tensile strength and elongation at break of the polymer. DMA studies have shown an increase in the storage modulus and glass transition temperature for mPE-ENS with respect to mPE-NS. Further, the TGA results have shown a higher thermal stability for mPE-ENS in comparison to mPE-NS.     

Barrier and Mechanical Properties of Poly(caprolactone)/organoclay Nanocomposites

In this study, biodegradable poly(caprolactone) (PCL) hybrids with two types of organoclays: Cloisite 30B (30B) and Cloisite 93A (93A) have been prepared by melt mixing and their barrier performance to air permeation and mechanical properties were investigated. The hybrids of PCL/30B were found to be nanocomposites resulted from the strong interaction between organic modifier of 30B and PCL and those of PCL/93A were microcomposites. The barrier performance of PCL/30B nanocomposite film to air permeation was much more improved than pure PCL and PCL/93A microcomposites at low organoclay concentration. With the increase of organoclay content the permeability coefficient was also increased that could attributed to the extra tortuous pathway for gas permeation caused by organoclay exfoliation. The barrier behaviour of PCL/30B nanocomposites could be approximately described by a theoretical model developed for composites. The mechanical properties measurements showed that the reinforcement of organoclay 30B in nanocomposites is more significant than 93A in microcomposites. Both tensile modulus and tensile strength were increased in PCL/30B nanocomposites even at at low amount of organoclay without much loss of strain at break as compared to pure PCL. The significant improvements in both barrier and mechanical properties in PCL nanocomposites could be attributed to the fine dispersion state of organoclay 30B platelets in PCL matrix and the strong interaction between organic modifier of 30B and matrix molecules.     

Preparation of Isotactic Polypropylene/Organoclay Nanocomposites by Solution Mixing Methodology: Structure and Properties Relationships

Isotactic Polypropylene (iPP) based nanocomposites filled with organo-clay nanoparticles were prepared and the relationships between their structure and properties were investigated. Modified C₁₆-C₁₈ smectite clay nanoparticles were used in order to promote matrix/filler compatibilization and to improve interfacial adhesion. X-Ray analysis performed on the nanocomposites demonstrated that at low organo-clay content (1 and 3% by weight) a nanostructure has been obtained, while in presence of 5% by weight of organoclay cluster regions have been formed. Mechanical tests showed that the elastic modulus increases of about 20% compared to the neat polymeric matrix value when 1 and 3% of nanofiller is added.     

Optimizing Melt‐Processing Conditions for the Preparation of iPP/Fumed Silica Nanocomposites: Morphology,Mechanical and Gas Permeability Properties

A series of iPP/SiO₂ nanocomposites, containing 1, 2.5, 5, 7.5, and 10 wt.‐% fumed silica nanoparticles, were prepared by melt mixing in a twin screw co‐rotating extruder. The effect of different extrusion parameters was evaluated. The size of aggregates increased with increase in SiO₂ content and repetition of the mixing process improved the filler's dispersion. A similar effect was also exhibited by either increasing the rotor speed or the mixing temperature, with the latter being more pronounced at the ranges studied. The mechanical properties of the prepared nanocomposites were evaluated and various models used to explain the observed enhancements. However, only the three‐phase model could provide some correlation with the experimental results. All nanocomposites displayed lower permeability to gases.

     

Acrylic,Elastomeric, Particle‐Dispersed Epoxy‐Clay Hybrid Nanocomposites: Mechanical Properties

Summary: Nanocomposites were formulated by curing a sonicated mixture of epoxy resin, C18 clay, and acrylic rubber dispersants. At 5.5 phr (parts per hundred) organoclay loading and a rubber concentration of 15 phr, the tensile‐failure strain of the nanocomposite was found to be higher than that of epoxy nanocomposite, rubber‐dispersed epoxy, and pristine epoxy. A plausible mechanism for improvement of the failure strain of nanocomposites is proposed.

Stress strain curves of filled and unfilled epoxy specimen.     

聚氯乙烯/聚丙烯酸丁酯/白泥纳米复合材料的研究

通过多步交换反应及扩散－聚合的方法,使聚丙烯酸丁酯被嵌入到改性层状结构的白泥层间,得到白泥－聚丙烯酸丁酯纳米复合物的微米粒子;然后将聚氯乙烯与白泥－聚丙烯酸丁酯进行熔融共混,制得具有一一特性的有机－无机纳米复合材料,并对复合材料的缺口冲击强度及动态力学性能进行了研究,结果表明,白泥－聚丙烯酸酯含量为5．0wt％时,复合材料的力学性能最佳;聚氯乙烯与高含量的白泥－聚丙烯酸丁酯（分别为25．0wt%和50．0wt%）形成的复合材料,在聚氯乙烯的玻璃化转变温度之前,储能模量出现先降低而后增加的过程。