辉光放电质谱技术应用进展

对辉光放电质谱(GDMS)在金属与半导体、非导体、薄层与深度分析、分子信息分析方面的应用和一些新装置、新方法进行了综述.着重介绍了近20年来我国学者在辉光放电质谱方面的成就,并结合国际上的报道对该领域的发展现状进行了总结.     

直流辉光放电质谱法测定多晶硅中关键杂质元素的相对灵敏度因子

采用直流辉光放电质谱(dc-GD-MS)测定多晶硅中关键杂质元素的相对灵敏度因子(RSF).标样制作过程中主要是在连续通入氩气条件下将固定量的非标准多晶硅样品熔化,向硅熔体中均匀掺入浓度范围为1～30 μg/g的关键杂质元素(如B和P),采用快速固化法制成标样;再将制成的标准样品加工成一系列适合GD-MS扁平池(Flat Cell)的片状样品(20 mm×20 mm×2mm).采用二次离子质谱法(SI-MS)对标准样品中关键掺杂元素进行多次定量测定,取平均值作为关键杂质元素的精确含量.优化一系列质谱条件后,运用GD-MS对标样中关键掺杂元素的离子强度进行多次测定,计算平均结果,得到未校正的表观浓度,利用标准曲线法计算出关键杂质元素的相对灵敏度因子.     

辉光放电质谱分析中质谱干扰及其校正方法的现状

详细地介绍了辉光放电质谱分析中的质谱干扰如同量异位素、多原子离子和多电荷离子干扰。从同位素选择、高分辨率仪器、碰撞诱导解离、离子源冷却、数学方法校正、放电气体更换和放电气体纯度提高等方面对辉光放电质谱的质谱干扰校正方法的现状进行了评述(引用文献共68篇)。     

辉光放电质谱法测定纯锡中24种杂质元素和锡记忆效应的消除

采用辉光放电质谱法(GDMS)测定了纯锡中24种杂质元素,分析方法为无标定量分析。分析前纯锡样品须依次用乙醇、水及乙醇冲洗以除去表面的灰尘颗粒,凉干后用于分析。本工作对辉光放电过程中的三项关键因素,即辉光放电电压、放电电流及放电气流三者在辉光放电溅射/电离时的相互关系及其对总离子流强度的影响进行了试验和讨论,并确定了仪器在最佳状态时辉光放电的优化条件为:放电电压590V,放电电流30mA,放电气流450mL·min~(-1)。为排除各元素测定中质谱(MS)干扰的影响,选择了在不同的分辨模式(中/高)下用相对丰度较高、干扰较少的质量数进行分析。所测定元素测定结果的相对标准偏差(n=5)均小于15%。各元素的检出限(3s)为0.003～0.174μg·g~(-1)之间。本方法所得测定结果与电感耦合等离子体原子发射光谱法(ICP-AES)或电感耦合等离子体质谱法(ICP-MS)的测定结果基本一致。经试验,通过更换GDMS的阳极帽、导流管、采样锥和透镜等4种耗材,可完全消除锡的记忆效应。     

辉光放电质谱研究与应用新进展

简要介绍了辉光放电的基本原理,主要概述了过去４年有关辉光放电质谱研究的新进展,包括辉光放电质谱的基础研究,新装置和新方法的发展,以及辉光放电质谱的分析应用。文中最后展望了辉光放电质谱法的发展前景。     

质谱的无机痕量分析进展

概述了电感耦合等离子体质谱(ICP-MS)、激光电离质谱(LIMS)和共振电离质谱(RIMS)、火花源质谱(SSMS)、辉光放电质谱(GDMS)、二次离子质谱(SIMS)、热电离同位素稀释质谱法(ID-TIMS)等无机质谱分析方法的基本原理、方法特点和应用进展,概括了ICE-MS和IDMS方法的优缺点;采用溶液进样的ICP-MS和TIMS稀释法,给出的测量结果不确定度要高于固体进样的质谱法。     

辉光放电质谱法定量测定重掺晶体硅中替位碳含量

采用辉光放电质谱法测定单晶硅中替位碳含量,通过优化仪器工作条件,得到最佳放电参数。利用低温傅里叶变换红外光谱法对呈梯度的四个单晶硅片中替位碳含量进行赋值,将辉光放电质谱法测得替位碳强度与硅的离子束比与赋值结果作工作曲线,计算得到相对灵敏度因子(RSF_(cal))为1.19。在优化过的工作条件下,用辉光放电质谱法测未知样,用RSF_(cal)进行计算,得到单晶硅中替位碳的定量分析结果,与二次离子质谱(SIMS)法测定结果进行对照,相对误差为3.7%,一致性较好。     

高流速辉光放电质谱法测定镍基单晶高温合金中43种痕量元素北大核心CSCD

基于高流速辉光放电质谱法(GDMS)的质谱干扰消除技术,对镍基单晶高温合金中43种痕量元素的质谱干扰与同位素选择进行了研究,用于高性能镍基单晶高温合金的纯净化水平评价。固体样品采用直接进样,通过复杂基体质谱干扰计算判定、共存元素干扰消除等方式,确定了待测元素的同位素和分辨率模式,通过相应标准物质对待测元素的相对灵敏度因子进行校正,采用高流速GDMS测定镍基单晶高温合金中43种痕量元素。结果表明,痕量元素的检出限(3s)为1.04×10^(-7)%~6.60×10^(-3)%,大部分元素的检出限达到0.1μg·g^(-1)级别;对内控标准物质DD6-6#测定6次,测定值的相对标准偏差为0.59%~13%。方法分析结果与不同分析方法对照、标准物质比对,结果吻合度高。     

辉光放电质谱（GDMS）法校正高纯氧化铋中19种元素的相对灵敏度因子

采用标准溶液加入法往高纯氧化铋中加入混合标准溶液,烘干并研磨均匀,制备了5个高纯氧化铋的控制样品。再挑取适量的粉末样品压在高纯铟薄片上,建立了辉光放电质谱(GDMS)法校正高纯氧化铋中的Mg、Al、Ca等19种元素相对灵敏度因子的方法。实验考察了放电参数和制样面积对基体信号强度和稳定性的影响,优化后的辉光放电电流为1.8mA,放电电压为950V,压在铟薄片上的高纯氧化铋直径约为6～8mm。通过选择合适的同位素,在4000的中分辨率下测定即可消除质谱干扰。为了验证加标回收的准确性,采用电感耦合等离子体质谱(ICP-MS)法对控制样品进行测定,所有元素的加标回收率都在80%以上。采用GDMS法测定5个控制样品并结合ICP-MS法的测定值建立工作曲线,大部分元素的线性均达到0.995以上;除Al、Ga、Sb外,大部分元素的校准相对灵敏度因子(calRSF)和仪器自带的标准相对灵敏度因子(stdRSF)的比值都在1/2～2之间,说明GDMS的半定量分析不会有数量级的差别。但对于某些需要准确测定纯度的定量分析,则必须采用基体相匹配的RSF值进行校正。     

辉光放电质谱法测定高纯材料中痕量硫杂质

准确测定并控制材料中杂质元素含量是发挥高纯材料性能不可或缺的环节。辉光放电质谱法(GDMS)是准确、快速、高灵敏分析高纯材料中痕量及超痕量硫的理想方法。对GDMS分析高纯铜和镍基高温合金中痕量硫的质谱干扰进行了讨论,优化了放电电流和放电电压,采用多种标准物质对硫的相对灵敏度因子(RSF)进行了校准和验证,并与二次离子质谱法(SIMS)进行分析结果比对,验证了GDMS定量分析结果的准确性和可靠性。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Selective syntheses of 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones via temperature-dependent Rh(II)-carbenoid-mediated 2H-azirine-ring expansion

The Rh(II)-catalyzed reaction of 2-carbonyl-substituted 2H-azirines with ethyl 2-cyano-2-diazoacetate or 2-diazo-3,3,3-trifluoropropionate provides an easy access to 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones. These compounds can be selectively prepared from the same starting material using temperature as the only varied parameter. The 2-azabuta-1,3-diene intermediate, a common precursor for both heterocyclic products, isomerizes into 2H-1,3-oxazine under kinetic control, while 1H-pyrrol-3(2H)-one is the sole product of the reaction at elevated temperatures. According to DFT-calculations a one-atom oxazine ring contraction involving ring-opening to a 2-azabuta-1,3-diene intermediate, followed by a 1,5- and 1,2-prototropic shift leads to the consecutive formation of imidoylketene and azomethine ylide, which then further undergo cyclization to the pyrrole derivative.     

Copper catalyzed/mediated synthetic methodology for ebselen and related isoselenazolones

Scope of the copper catalyzed/mediated selenium-nitrogen coupling reaction has been studied for the synthesis of isoselenazolones. It is noticed that the 2-chloro, 2-bromo-, and 2-iodo-aryl amides substrates can be exploited in the selenium-nitrogen coupling reaction by employing 25-100 mol % of CuI/1,10-phenanthroline (L) and potassium carbonate as a base in DMF. Furthermore, electron rich 2-chloro-arylamides also underwent selenium-nitrogen coupling reaction to give biologically important selenium-nitrogen heterocycles. Also, copper-catalyzed selenium-nitrogen coupling reaction has been meticulously applied for the synthesis of diaryl diselenides having methoxy, amine, and amide functionality from respective aryl iodides in the presence of stoichiometric amount of succinimide as an external Se-N coupling partner.     

Knoevenagel condensation catalyzed by novel Nmm-based ionic liquids in water

A series of novel N-methyl morpholine (Nmm) based ionic liquids with 1,2-propanediol group were synthesized and used as catalysts for Knoevenagel condensation at room temperature in water. Under the effect of the catalyst, various aldehydes or aliphatic ketones could react with a wide range of activated methylene compounds well, including malononitrile, alkyl cyanoacetate, cyanoacetamide, β-diketone, barbituric acid, 2-arylacetonitrile and thiazolidinedione. Furthermore, most of the products could be separated just by filtrating and washing with water. Additionally, the catalyst is recyclable and applicable for the large-scale synthesis.     

Construction of polyheterocyclic spirotetrahydrothiophene derivatives via sulfa-Michael/aldol cascade reaction

A series of polyheterocyclic spirotetrahydrothiophene derivatives were obtained in moderate to excellent yields via a catalyst-free sulfa-Michael/aldol cascade reaction of chalcones 1 and commercially available 1,4-dithiane-2,5-diol 2 under mild conditions. We also present the first asymmetric sulfa-Michael/aldol cascade reaction of chalcones 1 and commercially available 1,4-dithiane-2,5-diol 2 with moderate to good enantioselectivities catalyzed by readily available chiral phase-transfer catalysts (PTCs).     

Suzuki-Miyaura reactions of the soluble guanylate cyclase inhibitor NS2028: a non-product specific route to C-8 substituted analogues

Both soluble guanylate cyclase (sGC) inhibitors ODQ 1 and NS2028 2 are synthesized via improved protocols. In the former case treating 3,4-dihydroquinoxalin-2(1H)-one oxime 8, which can be prepared in two steps from 1,2-benzenediamine, with 1,1′-carbonyldiimidazole (CDI) gives the dihydro-ODQ 10 that in the presence of KMnO₄ oxidises to give ODQ 1 in an overall yield of 46% starting from 1,2-benzenediamine. In the latter case, the synthesis affords NS2028 2 from 2-amino-4-bromophenol 3 in three steps with an overall yield of 85% and avoids the need for chromatography. Furthermore, Suzuki-Miyaura reaction conditions are described that enable the preparation of 8-aryl and 8-heteroaryl derivatives of NS2028 directly from NS2028 2. Finally, demethylation of the 8-(methoxyphenyl) substituted analogues afforded the 8-(hydroxyphenyl) derivatives 40-42. All new products are fully characterised.