一种新颖的长周期光纤光栅可调增益均衡器

发现高频CO2激光脉冲写入的新型长周期光纤光栅的谐振波长对特定圆周方向的横向负载不敏感，谐振峰幅值随横向负载而线性变化；而且这种长周期光纤光栅的谐振波长随温度变化而线性变化，谐振峰幅值对温度变化不敏感。由此设计而成的可调增益均衡器可实现谐振波长和幅值的动态独立调节，能很好地满足均衡掺铒光纤放大器增益谱的需要。     

Transmission properties in a one-dimensional finite extrinsic semiconductor InSb photonic crystal

The properties of wave transmission in a strongly dispersive semiconductor-dielectric photonic crystal (SDPC) are theoretically investigated. We consider a one-dimensional finite SDPC, air/(SD) ^N S/air, where, N is the stack number, S is an extrinsic semiconductor, n-type InSb (n-InSb), and D is a dielectric layer of SiO₂. Transmission peaks can be found in the frequency region where the real part of the complex permittivity of n-InSb is negative. The number of peaks is equal to the stack number N. The positions of peaks can be tuned by the thicknesses of S and D. The peaks are seen to be blue-shifted as the doping density increases, leading to a tunable filter. The locations of peaks are also strongly dependent on the incidence angle, but weakly dependent on the polarization of the incident wave. The results suggest that a tunable multichannel filter can be achieved by using such an SDPC. Filters with tunable and multichannel features are of technical use in photonic applications such as in the optical electronics and communications.     

The peculiarities of radiation of chiral photonic crystals with isotropic defect layer

The peculiarities of defect modes and reflection spectra of chiral photonic crystals (CPC) with an isotropic defect for various thicknesses of the defect layer were investigated. The peculiarities of the spectra of photonic density of the state (DOS) and those of the intensity at the center of the defect were investigated, too. It was shown that there is one more possibility of tuning of laser emission - by the change of the defect layer thickness - in CPCs doped with laser dyes (with resonance atoms) and with an isotropic defect. It was shown that the given system can work as a tunable narrow-band filter (or mirror) with tunable wavelength width and tunable location of frequency of the complete transmittance (reflection) band. The radiation peculiarities of these systems were discussed. It was shown that in certain conditions an anomalous strong radiation can be observed for defect modes, and low-threshold laser generation is possible, again, for these modes. It was also shown that radiation suppression is possible for defect modes. The peculiarities of group velocity, group velocity dispersion and non-reciprocity were studied.     

A quantitative analysis of an athermal design for a long period grating based tunable filter

In this paper, a quantitative analysis of an athermal design for a unique all-fiber tunable filter based on the combination of a single resonant band long period grating (LPG) with an electro-optic polymer second cladding layer is presented. The single resonant band LPG is used to select the resonant wavelength, which can be tuned by changing the refractive index of an electro-optic polymer second cladding layer via external electric field. Although the basic operational principle and implementation of this unique tunable filter have been previously reported, this paper is focused on the quantitative analysis of the athermal design, which may significantly enhance the practicability of the proposed tunable filter.     

基于光纤叠栅的全光纤声光可调谐滤波器的特性分析

本文提出了一种基于光纤叠栅的全光纤声光可调谐滤波器, 与普通光纤布拉格光栅型全光纤声光可调谐滤波器相比, 该滤波器能够对光纤叠栅的两个中心波长进行同步调制. 理论分析了声波频率和声致应变幅度对基于光纤叠栅的全光纤声光可调谐滤波器的传输光谱的影响, 结果表明, 各阶次反射峰分别以两个主反射峰为中心呈对称关系, 且主反射峰与其所调制出的次反射峰之间的波长间隔与声波频率成正比, 而两个主反射峰所调制出的同阶次反射峰之间的波长间隔与声波频率无关; 声致应变幅度主要影响主反射峰及次反射峰的反射率的变化. 实验中, 分别测试声波频率为390 kHz和710 kHz的基于光纤叠栅的全光纤声光可调谐滤波器的传输光谱, 实验结果的变化趋势与仿真分析结果相一致.     

Tunable double-channel filter based on two-dimensional ferroelectric photonic crystals

A tunable double-channel filter is presented, which is based on a two-dimensional nonlinear ferroelectric photonic crystal made of cerium doped barium titanate. The filtering properties of the photonic crystal filter can be tuned by adjusting the defect structure or by a pump light. The influences of the structure disorders caused by the perturbations in the radius or the position of air holes on the filtering properties are also analyzed.     

Tunable multilayer narrowband filter containing an ultrathin metallic film and a lithium niobate defect

By using lithium niobate (LiNbO₃) as a defect layer, a tunable multilayer narrowband reflection-and-transmission filter containing an ultrathin metallic film is proposed. Due to the voltage dependence of the refractive index for LiNbO₃, tunable optical filtering properties have been theoretically investigated based on the calculated wavelength-dependent reflectance and transmittance. The dependences of peak wavelength on the applied voltage and the angle of incidence are numerically illustrated. The results reveal that in addition to working as a tunable filter, it can also be expected to act as a refractometric optical sensor.     

Tunable guided-mode resonance filter based on dielectric elastomer actuators

A tunable guided-mode resonant (GMR) reflection filter based on dielectric elastomer actuators (DEA) is designed. Simulating the characteristics of the filter with rigorous coupled wave analysis, it is shown that the resonant wavelength of the kind of GMR filter can be tuned from 1442.8 nm to 1644.6 nm by applying voltage on the dielectric elastomer actuators which changes the period of the grating layer of the GMR filter conveniently. Furthermore, there is an almost perfect linear relationship of resonant wavelength tuned and the period varied with negligible effect on the linewidth.     

Tunable Filters with Narrow-Band in Bulk SLA for DWDM Networks

The filter mechanism of a tunable filter with narrow-band in bulk semiconductor laser amplifier (SLA) is analyzed, which is suitable for dense wavelength division multiplexed (DWDM) optical fiber networks. The wavelength selectivity of the filter is derived from nondegenerate four-wave mixing (NDFWM) in semiconductor gain medium. It uses the direction of propagation to separate the desired wave-mixing product from the other light beams. The filters are shown to have very narrow passbands (subangstrom bandwidth) tunable over the entire semiconductor gain bandwidth. We gave the theoretical analysis of NDFWM effect in semiconductor gain medium is given and a set of nonlinear coupled wave equations is deduced, which are processed efficiently by Runge-Kutta method in numerical simulation. The influences of various structural parameters of the filter on the output bandwidth and efficiency were also discussed.     

液晶法布里-玻罗滤波器可调谐特性分析

分析了液晶法布里－玻罗可调滤波器中介质反射镜反射相位引起的峰值波长漂移. 液晶法－玻滤波器通过外加电压调谐峰值波长, 反射相位会导致峰值波长漂移使器件不能达到DWDM系统的使用要求. 本文推导了一套计算反射镜反射相位的公式,将它应用于液晶法-玻可调滤波器的理论设计, 模拟结果定量表示了反射相位对峰值波长造成的影响. 这对确定液晶可调滤波器峰值波长和设计器件电驱动装置具有重要意义. 由此设计了一个在光通讯波段可单调调谐的液晶法-玻滤波器.     

Influence of morphology on the emissive properties of dye-doped PVP nanofibers produced by electrospinning

Dye-doped polymer micro- and nanofibers with tailored light emission properties have great potential for applications in optical, optoelectronic, or photonic devices. In this study, these types of structures were obtained by electrospinning rhodamine 6 G-doped polyvinylpyrrolidone (PVP) using a polymer solution of 10% (mass) concentration in ethanol. Polymer nanofibers with different morphologies (smooth and beaded) and diameters of about 500 nm were obtained using different electrospinning conditions with the same solutions. Fluorescence optical microscopy observations showed that the dye was distributed uniformly in the doped PVP nanofibers. Different shifts were observed when we compared the wavelength of the dye emission band peak of the smooth nanofibers (566 nm) and the wavelength of the dye emission band peak of the beaded fibers (561.5 nm) produced by electrospinning in different conditions with the wavelength of the emission band peak for transparent thin films produced by spin coating (558 nm) using the same polymer solution. This demonstrates that it is possible to tune the optical properties of electrospun dye-doped polymer nanofibers simply by modifying the morphology of the material, i.e., the parameters of the electrospinning process.     

Tunable Filters with Narrow Band in Bulk SLA for DWDM Networks

１　Ｉｎｔｒｏｄｕｃｔｉｏｎ　　Ｔｏｄａｙ,ｗｉｔｈｔｈｅｑｕｉｃｋｄｅｖｅｌｏｐｍｅｎｔｏｆｔｈｅｈｉｇｈｄｅｎｓｅｗａｖｅｌｅｎｇｔｈｄｉｖｉｓｉｏｎｍｕｌｔｉｐｌｅｘｉｎｇ,ｔｈｅｌｉｎｋｃａｐａｃｉｔｙｗｉｌｌｂｅｇｒｅａｔｌｙｅｎｈａｎｃｅｄ．Ａｌｔｅｒｎａｔｉｖｅｌｙ,ｔｈｅｅｎｈａｎｃｅｍｅｎｔｏｆｔｈｅｌｉｎｋｃａｐａｃｉｔｙｄｅｐｅｎｄｓｏｎｔｈｅｒｅｌａｔｉｖｅｌｙｈｉｇｈｗａｖｅｌｅｎｇｔｈｒｅｓｏｌｕｔｉｏｎｏｆｔｈｅｗａｖｅｌｅｎｇｔｈｆｉｌｔｅｒｓｉｎｔｈｅｒｅｃｅｉ…     

光子晶体多通道可调谐偏振滤波器的理论研究

通过对设计的一维掺杂光子晶体的数值计算和理论分析,得出了两个偏振态缺陷模透射峰的变化特征为:P-偏振波其缺陷模透射峰在入射角大于0.75(rad)范围内有多条明显的缺陷模透射峰带,而S-偏振波在入射角大于0.75 (rad) 范围内没有缺陷模透射峰;P-偏振波缺陷模在同一杂质光学厚度可以截到多个波长不同的透射峰.以此为基础设计出滤波通道波长可调范围大于60 nm 、滤波通道的半高宽可调范围在1~5 nm、滤波通道透射峰值大于0.98的一维光子晶体三通道可调谐偏振滤波器.     

谐振腔侧边1×5介质柱调谐光子晶体滤波器

在正方格二维光子晶体结构中设计了基于可调谐谐振腔的带通滤波器,通过改变1×5谐振腔侧边调谐介质柱位置调节谐振腔与波导系统工作时传输的波段,用CMT理论分析了输入端耦合衰减率及输入端失谐因子对滤波器的影响。借助FDTD方法得到了滤波器波长传输谱,结果表明:当滤波器结构工作于1320~1810 nm波长段时,输出端38个通帯的-3 dB带宽Δλ范围为4.18~11.15 nm,通带峰值波长可调宽度为186.56 nm。该微型滤波器适于光电通信粗波分解复用WDDM系统设计和光集成设计等方面。     

铁电液晶缺陷光子晶体调谐滤波器的设计

将铁电液晶作为缺陷层引入一维光子晶体中,用电场改变液晶分子的取向,形成光子晶体快速可调谐滤波器.用传输矩阵法研究了铁电液晶缺陷光子晶体的可调谐滤波特性,计算了电压和液晶材料参量对滤波器透射谱的影响.结果表明:改变电压能容易改变光子晶体滤波器透射峰的位置、强度、个数和带宽,实现良好的调谐滤波功能.     

Use of photonic quantum well as tunable defect in multilayer narrowband reflection-and-transmission filter

By using a photonic quantum well (PQW) as a tunable defect layer, a theoretical analysis on the optical properties in a multilayer narrowband reflection-and-transmission filter can be given. It is found that the resonant peaks in the reflection and transmission spectra are shifted to shorter wavelengths as the number of periods in the PQW increases. The shifting feature is more salient if the QW is deeper, that is, the refractive index contrast in the constituents of the PQW is increased. This novel design provides an alternative for achieving a tunable filter instead of using the usual electrooptical defect.     

A tunable infrared plasmonic polarization filter with asymmetrical cross resonator

A tunable infrared plasmonic polarization filter is proposed and investigated in this paper. The filter is based on the sandwich absorption structure which consists of three layers. The top layer is an array of asymmetrical cross resonator.The middle and bottom layers are dielectric spacer and metal film respectively. By absorbing specific wavelength of the incident light perfectly, the reflection spectrum of the structure shows filter performance. The calculated results show that the absorption wavelength is strongly dependent on the length of branch of the asymmetrical cross resonator which is parallel to the light polarization and independent of the length of the vertical one. Therefore, the asymmetrical cross resonator filter structure opens the way for freely tuning the filtering wavelength for a different light polarization. We can fix a resonant wavelength(absorption wavelength) corresponding to one polarization and change the resonant wavelength for the other polarization by adjusting the corresponding branch length of the asymmetrical cross resonator, or change the two resonant wavelengths of both two polarizations at the same time.     

Thermally tunable THz filter made of semiconductors

By using the finite-difference time domain method, the transmission properties of terahertz wave passing through two different periodic subwavelength structures on InSb semiconductor slabs under different temperatures have been investigated. The results show that the peak transmittance increases and the transmittance peak has a blue shift when the temperature is increasing. It is extremely versatile to control the tunable THz filter by varying the temperature.     

Suppression of Nonlinear Patterning Effect in Wavelength Conversion Based on Transient Cross-Phase Modulation in Semiconductor Optical Amplifier Assisted with a Detuning Filter

Nonlinear patterning （NLP） effect in wavelength conversion based on transient cross-phase modulation （XPM） in semiconductor optical amplifier （SOA） assisted with a detuning filter is theoretically investigated. A non- adiabatic model is used to estimate the ultrafast dynamics of gain, phase and electron temperature in the SOA. Simulation results show that the NLP can be greatly suppressed by introducing an assist light, especially for the probe wavelength distant from gain peak. Furthermore, the results also indicate that the improvement is more evident for long wavelength probe light and assist light in counter-propagating configuration.     

A new type of small size acousto-optic tunable filter with super narrow optical linewidth

The new concept of the creation of an acousto-optic tunable filter (AOTF) with super-resolution and small size is discussed. The advantage of the device is based on the use of a novel type of multi reflector beam expander that produces a highly collimated optical beam (angular spread about 100 ppm), tilted with a change in optical wavelength. The proposed AOTF, 1 cm in length, can have an optical linewidth about 0.1 nm and up to 400 tunable channels at a wavelength of 1540 nm. It can be utilized as a tunable filter for dense wavelength-division multiplexing (DWDM) in fiber optic networks and as a small-sized tunable optical spectrometer, for example, in sensors of gases, liquids and solids. The acousto-optic tunable filter can be developed by known technology developed for the creation of integrated optics and microelectronics devices. Received: 28 April 2001 / Revised version: 22 August 2001 / Published online: 2 November 2001