Phase transformation behavior and dielectric characteristics of BaTi1−x(Al1/2Nb1/2)xO3 (0.01≤x≤0.40) ceramics

Microstructure, phase transformation behavior and dielectric properties of BaTi_1−x(Al_1/2Nb_1/2)_xO₃ (0.01≤x≤0.40) ceramics were investigated. A high level of (Al_1/2Nb_1/2)⁴⁺ substitution for Ti⁴⁺ ions was not conducive to the stability of the perovskite structure and resulted in the formation of BaAl₂O₄. As x was increased, lattice constants and unit cell volume decreased, reached a minimum at x=0.10 and then increased. The BaTi_1−x(Al_1/2Nb_1/2)_xO₃ ceramics at room temperature experienced a transformation from ferroelectric to paraelectric phase with increasing (Al_1/2Nb_1/2)⁴⁺ concentration. Meanwhile, permittivity of the BaTi_1−x(Al_1/2Nb_1/2)_xO₃ ceramics was markedly reduced, while Q value was slightly increased. Frequency dispersion of dielectric peak was obviously increased as x was increased from 0.01 to 0.10. It is of great interest that a dielectric abnormity represented by a broad dielectric peak at 200-400 K was observed for the composition with x=0.40.     

Ferroelectric-relaxor behavior of (Na0.5K0.5)NbO3-based ceramics

We report that ferroelectric-relaxor behavior is induced by doping of SrO and TiO₂, or BaO and TiO₂ into classic ferroelectric (Na_0.5K_0.5)NbO₃. It is found that [(Na_0.5K_0.5)_0.9Sr_0.1](Nb_0.9Ti_0.1)O₃ ceramics exhibit a pronounced ferroelectric-relaxor behavior, comparable to that of [(Na_0.5K_0.5)_0.9Ba_0.1](Nb_0.9Ti_0.1)O₃ ceramics. Our results indicate that the relaxor behavior is closely related to the appearance of micropolar regions in these systems. The relaxor behavior should arise from the dynamic response of micropolar clusters. Raman spectra of [(Na_0.5K_0.5)_1−xSr_x](Nb_1−xTi_x)O₃ ceramics measured in the wavenumber range from 100 to 1200 cm⁻¹ confirm that the first order scattering is dominant in phonon bands should result from both short-range ordered region (micropolar regions) and disordered matrix. The frequency dependence of dielectric permittivity measurements show that the relaxor behavior of SrO and TiO₂, or BaO and TiO₂ doped (Na_0.5K_0.5)NbO₃ ceramics is not a Debye type in the radio frequency range.     

Dielectric and piezoelectric properties of lead-free (Na0.5K0.5)NbO3-SrTiO3 ceramics

In this article, we report successful preparation of dense [(Na_0.5K_0.5)_1−xSr_x](Nb_1−xTi_x)O₃ (x=0.005-0.100) ceramics by ordinary sintering in air. The dependence of phase structure on doping content of SrO and TiO₂ has been determined by the X-ray diffraction technique. It was found that the crystal structure changed from orthorhombic to tetragonal at x≈0.040. Dielectric study revealed that the dielectric relaxor behavior was induced by doping of SrO and TiO₂ into (Na_0.5K_0.5)NbO₃. The samples in the composition range from x=0.005 to 0.020 exhibited excellent electrical properties, piezoelectric constant of electromechanical planar and thickness coupling coefficients of k_p=26.6-32.5% and k_t=39.8-43.8%. The results show that the [(Na_0.5K_0.5)_1−xSr_x](Nb_1−xTi_x)O₃ ceramics are one of the promising lead-free materials for electromechanical transducer applications.     

Raman characterization of Pb2Na1−xLaxNb5−xFexO15 and Pb0.5(5−x)LaxNb5−xFexO15 (0≤x≤1) solid solutions

The ferroelectric compounds Pb₂Na_1−xLa_xNb_5−xFe_xO₁₅ and Pb_0.5(5−x)La_xNb_5−xFe_xO₁₅ (0≤x≤1) with the tungsten bronze type structure have been investigated using Raman spectroscopy. The evolution of the spectra as a function of composition at room temperature is reported. In the frequency range 200-1000 cm⁻¹ three main A₁ phonons around 240 (υ₁), 630 (υ₂) and 816 (υ₃) cm⁻¹ were observed. The broadening of the Raman lines for high values of x originates from a significant structural disorder. This is in good agreement with the relaxor character of these compositions. The lowest-frequency part of the spectra, below 180 cm⁻¹, reveals a structural change in the studied solid solutions. The behaviour of the Raman shift of the υ₁ mode confirms that in Pb₂Na_1−xLa_xNb_5−xFe_xO₁₅, a clear anomaly occurs in the vicinity of x=0.4.     

Structural and dielectric properties in the (Ba1−xCax)(Ti0.95Zr0.05)O3 ceramics

Lead-free (Ba_1−xCa_x)(Ti_0.95Zr_0.05)O₃ (x = 0.05-0.40) (BCZT) ceramics were prepared by solid-state reaction technique. XRD results show that the samples in the composition range of 0.05 ≤ x ≤ 0.25 exhibit pure perovskite structures and undergo a polymorphic phase transitions from orthorhombic to tetragonal phase around room temperature. The biphasic structures are detected at x ≥ 0.30 and the dielectric peaks become broad and dielectric constants decrease with increasing Ca content. Ca replacement at Ba site leads to diffuseness, whereas Ca occupancy at Ti site leads to decrease of the T_c.     

Observation of magnetoelectric behavior at room temperature in Pb(FexTi1−x)O3

The co-existence of ferroelectric and ferromagnetic properties at room temperature is very rarely observed. We have been successful in converting ferroelectric PbTiO₃ into a magnetoelectric material by partly substituting Fe at the Ti site. The Pb(Fe_xTi_1−x)O₃ system exhibits ferroelectric and ferromagnetic ordering at room temperature. Even more remarkably, our results demonstrate a coupling between the two order parameters. Hence it could be a futuristic material to provide cost effective and simple path for designing novel electromagnetic devices.     

Post-sintering annealing effect on the diffuse phase transition in (Pb1−xBax)(Yb0.5Ta0.5)O3 ceramics

The effect of post sintering annealing on the dielectric response of (Pb_1−xBa_x)(Yb_0.5Ta_0.5)O₃ ceramics in the diffuse phase transition range (x=0.2) has been investigated. The samples are prepared by conventional solid-state reaction method. The samples are sintered at 1300 °C for 2 h and annealed at different temperatures (800, 900 and 1000 °C) for 8 h and at 800 °C for different time durations (8, 12 and 24 h). A significant change in the dielectric response has been observed in all the samples. The dielectric constant increases remarkably and the dielectric loss tangent decreases. The dielectric peaks of the annealed samples are observed to be more diffused with noticeable frequency dispersion compared to the as sintered sample.     

Dielectric properties and phase transitions of (Pb0.87La0.02Ba0.1)(Zr0.6Sn0.4−xTix)O3 ceramics with compositions near AFE/RFE phase boundary

The electrical properties and phase transition behavior of (Pb_0.87La_0.02Ba_0.1)(Zr_0.6Sn_0.4−xTi_x)O₃ solid solutions (PLBZST, 0.04≤x0.2) were investigated by the X-ray diffraction, permittivity, pyroelectric current, and P-E electric hysterisis loops. As the composition x increased from 0.04 to 0.2, the antiferroelectric ceramics (x≤0.07, AFE) with tetragonal phase changed to the ferroelectric relaxors (RFE, 0.09≤x). AFE ceramics showed a peculiar diffuse phase transition and dielectric relaxation at the low temperature (down to −100 °C) due to a frustration between AFE and FE state. With an increase in composition x, electrically field-induced AFE-FE switching field (E_AFE-FE) and AFE-paraelectric (PE) phase transition temperature (T_c) are depressed in the temperature (T)-Ti composition (x) phase diagram, a FE-AFE-PE triple phase point (T_tr) with the lowest transition temperature occurred at x=0.09. The pyroelectric currents under an application of various external electric field (E) were measured to identify a T-E phase diagram of the PLBZST compound.     

Effect of electric field on electrocaloric effect in Pb(Zr1 − xTix)O3 solid solution

A thermodynamic analysis is employed to investigate the intrinsic electrocaloric effect of Pb(Zr_1 − xTi_x)O₃ solid solution system under the different electric field. Theoretical analysis indicates that Pb(Zr_1 − xTi_x)O₃ system has the giant electrocaloric coefficient and the large adiabatic temperature change near its ferroelectric Curie temperature. The applied electric field decreases not only the electrocaloric coefficient but also its temperature dependence. Furthermore, it increases the adiabatic temperature change as well as its dependence of temperature. The temperature corresponding to the maximum of electrocaloric coefficient and adiabatic temperature change increases with the enhancement of electric field because of its first-order phase transition between ferroelectric phase and paraelectric phase.     

Na1−xLixNbO3 ceramics studied by X-ray diffraction, dielectric, pyroelectric, piezoelectric and Raman spectroscopy

Na_1−xLi_xNbO₃ ceramics with composition 0.05≤x≤0.30 were prepared by solid-state reaction method and sintered in the temperature range 1100-1150 °C. These ceramics were characterised by X-ray diffraction as well as dielectric permittivity measurements and Raman spectroscopy. Dielectric properties of ceramics belonging to the whole composition domain were investigated in a broad range of temperatures from 300 to 750 K and frequencies from 0.1 to 200 kHz. The Rietveld refinement powder X-ray diffraction analysis showed that these ceramics have a single phase of perovskite structure with orthorhombic symmetry for x≤0.15 and two phases coexistence of rhombohedral and orthorhombic above x=0.20. The evolution of the permittivity as a function of temperature and frequency showed that these ceramics Na_1−xLi_xNbO₃ with composition 0.05≤x≤0.15 present the classical ferroelectric character and the phase transition temperature T_C increases as x content increases. The polarisation state was checked by pyroelectric and piezoelectric measurements. For x=0.05, the piezoelectric coefficient d₃₁ is of 2pC/N. The evolution of the Raman spectra was studied as a function of temperatures and compositions. The results of the Raman spectroscopy study confirm our dielectric measurements, and they indicate clearly the transition from the polar ferroelectric phase to the non-polar paraelectric one.     

Phase transition, structural and electrical properties of Pb(Zn1/3Nb2/3)O3-doped Pb(Ni1/3Nb2/3)O3-PbTiO3 ceramics prepared by solid-state reaction method

Phase pure perovskite (1−x−y)Pb(Ni_1/3Nb_2/3)O₃-xPb(Zn_1/3Nb_2/3)O₃-yPbTiO₃ (PNN-PZN-PT) ferroelectric ceramics were prepared by conventional solid-state reaction method via a B-site oxide mixing route. The PNN-PZN-PT ceramics sintered at the optimized condition of 1185 °C for 2 h exhibit high relative density and rather homogenous microstructure. With the increase of PbTiO₃ (PT) content, crystal structure and electrical properties of the synthesized PNN-PZN-PT ceramics exhibit successive phase transformation. A morphotropic phase boundary (MPB) is supposed to form in (0.9−x)PNN-0.1PZN-xPT at a region of x=32-36 mol% confirmed by X-ray diffraction (XRD) measurement and dielectric measurement. The MPB composition can be pictured as providing a “bridge” connecting rhombohedral ferroelectric (FE) phase and tetragonal one since crystal structure of the MPB composition is similar to both the rhombohedral and tetragonal lattices. Dielectric response of the sintered PNN-PZN-PT ceramics also exhibits successive phase-transition character. 0.64PNN-0.1PZN-0.26PT exhibits broad, diffused and frequency dependent dielectric peaks indicating a character of diffused FE-paraelectric (PE) phase transition of relaxor ferroelectrics and 0.40PNN-0.1PZN-0.50PT exhibits narrow, sharp and frequency independent dielectric peaks indicating a character of first-order FE-PE phase transition of normal ferroelectrics. The FE-PE phase transition of 0.56PNN-0.1PZN-0.34PT is nearly first-order with some diffused character, which also exhibits the largest value of piezoelectric constant d₃₃ of 462pC/N.     

Microstructure and piezoelectric properties of Bi0.5(Na0.82K0.18)0.5TiO3−NaSbO3 ceramics

Lead-free piezoelectric ceramics (1−x)Bi_0.5(Na_0.82K_0.18)_0.5TiO₃−xNaSbO₃ have been prepared by a conventional ceramics technique, and their microstructure and electrical properties have been investigated. The addition of NaSbO₃ has no remarkable effect on the crystal structure within the studied doping content; however, an obvious change in microstructure took place. With increase in NaSbO₃ content, the temperature from a ferroelectric to antiferroelectric phase transition increases, and the temperature for a transition from antiferroelectric phases to paraelectric phases changes insignificantly. Simultaneously, the temperature range between the rhombohedral phase transition point and the Curie temperature point becomes smaller. The piezoelectric properties significantly increase with increase in NaSbO₃ content and the piezoelectric constant and electromechanical coupling factor attain maximum values of d₃₃=160 pC/N and k_p=0.333 at x=0.01. The results indicate that (1−x)Bi_0.5(Na_0.82K_0.18)_0.5TiO₃−xNaSbO₃ ceramic is a promising lead-free piezoelectric candidate material.     

Enhanced ferroelectric, magnetic and magnetoelectric properties of Bi1−xCaxFe1−xTixO3 solid solutions

We report on the enhanced electromechanical, magnetic and magnetoelectric properties of Bi_1−xCa_xFe_1−xTi_xO₃ solid solutions. The crystal structure of the x≈0.25 compounds are close to the rhombohedral-orthorhombic phase boundary, and the solid solutions are characterized by increased electromechanical properties due to the polarization extension near the polar-nonpolar border. The homogenous weakly ferromagnetic state is established at x>0.15 doping. The chemical doping shifts the magnetic transition close to room temperature, thus enlarging the magnetic susceptibility of the compounds. The solid solutions at the morphotropic phase boundary exhibit a nearly twofold increase in piezoelectric response, whereas the magnetoelectric coupling shows five times enhancement in comparison with the parent bismuth ferrite.     

Li0.5Fe2.5−xMnxO4 ferrite sintered from microwave-induced combustion

Li_0.5Fe_2.5−xMn_xO₄ (0≦x≦1.0) powders with small and uniformly sized particles were successfully synthesized by microwave-induced combustion, using lithium nitrate, ferric nitrate, manganese nitrate and carbohydrazide as the starting materials. The process takes only a few minutes to obtain as-received Mn-substituted lithium ferrite powders. The resultant powders annealed at 650 ^°C for 2 h and were investigated by thermogravimeter/differential thermal analyzer (TG/DTA), X-ray diffractometer (XRD), transmission electron microscopy (TEM), vibrating sample magnetometer (VSM), and thermomagnetic analysis (TMA). The results revealed that the Mn content were strongly influenced the magnetic properties and Curie temperature of Mn-substituted lithium ferrite powder. As for sintered Li_0.5Fe_2.5−xMn_xO₄ specimens, substituting an appropriate amount of Mn for Fe in the Li_0.5Fe_2.5−xMn_xO₄ specimens markedly improved the complex permeability and loss tangent.     

Structural, ferroelectric and impedance spectroscopy properties of Y modified Pb(Fe0.5Nb0.5)O3 ceramics

Some ceramic samples of Pb_1−xY_x(Fe_0.5Nb_0.5)_1−x/4O₃ (PYFN) (0.00≤x≤0.08) were synthesized by a mixed oxide route. X-ray diffraction patterns of all the above samples confirm the formation of single phase material crystallizing in monoclinic structure. Dielectric properties (ε_r and tan δ) were analyzed in a wide temperature (30-350 °C) and frequency range (100 Hz-1 MHz). Ferroelectric properties of these compounds were confirmed from polarization (P-E hysteresis loop) measurements at room temperature. All the room temperature hysteresis loops of PYFN ceramics were well simulated using the ferroelectric capacitor model. Yttrium substitution resulted in notable enlargement of room temperature remnant polarization (2P_r). The 2P_r of PYFN (x=0.02) reaches to a large value (23 μC/cm²), which is nearly 5 times greater than that of PFN ceramic (4.6 μC/cm²). All the compounds exhibits negative temperature coefficient of resistivity (NTCR) type behavior as that of semiconductors. Dc conductivity (estimated via bulk resistivity) variation with temperature of all the samples follows Arrhenius type of electrical conductivity.     

Electrical properties of SrBi2(Nb0.5Ta0.5)2O9 ceramics

Aurivillius SrBi₂(Nb_0.5Ta_0.5)₂O₉ (SBNT 50/50) ceramics were prepared using the conventional solid-state reaction method. Scanning electron microscopy was applied to investigate the grain structure. The XRD studies revealed an orthorhombic structure in the SBNT 50/50 with lattice parameters a=5.522 Å, b=5.511 Å and c=25.114 Å. The dielectric properties were determined by impedance spectroscopy measurements. A strong low frequency dielectric dispersion was found to exist in this material. Its occurrence was ascribed to the presence of ionized space charge carriers such as oxygen vacancies. The dielectric relaxation was defined on the basis of an equivalent circuit. The temperature dependence of various electrical properties was determined and discussed. The thermal activation energy for the grain electric conductivity was lower in the high temperature region (T>303.6 °C, E_a−ht=0.47 eV) and higher in the low temperature region (T<303.6 °C, E_a−lt=1.18 eV).     

Maxwell-Wagner characterization of dielectric relaxation in Ni0.8Zn0.2Fe2O4/Sr0.5Ba0.5Nb2O6 composite

Dense composites were prepared through incorporating the dispersed Ni_0.8Zn_0.2Fe₂O₄ ferromagnetic particles into Sr_0.5Ba_0.5Nb₂O₆ ferroelectric matrix. Extrinsic dielectric relaxation and associated high permittivities of the materials are reported in the composites. We used an ideal equivalent circuit to explain electrical responses in impedance formalism. A Debye-like relaxation in the permittivity formalism was also found. Interestingly, real permittivity (ε′) of the sample containing 30% Ni_0.8Zn_0.2Fe₂O₄ shows obvious independence of the temperature at 100 kHz. Dielectric relaxation and high-ε′ properties of the composites are explained in terms of the Maxwell-Wagner (MW) polarization model.     

The influence of microscopic parameters on the ionic conductivity of SrBi2(Nb1−xVx)2O9−δ(0≤x≤0.3) ceramics

Layered SrBi₂(Nb_1−xV_x)₂O_9−δ (SBVN) ceramics with x lying in the range 0-0.3 (30 mol%) were fabricated by the conventional sintering technique. The microstructural studies confirmed the truncating effect of V₂O₅ on the abnormal platy growth of SBN grains. The electrical conductivity studies were centred in the 573-823 K as the Curie temperature lies in this range. The concentration of mobile charge carriers (n), the diffusion constant (D₀) and the mean free path (a) were calculated by using Rice and Roth formalism. The conductivity parameters such as ion-hopping rate (ω_p) and the charge carrier concentration (K′) term have been calculated using Almond and West formalism. The aforementioned microscopic parameters were found to be V₂O₅ content dependent on SrBi₂(Nb_1−xV_x)₂O_9−δ ceramics.     

Phase diagram of the relaxor (1−x)Pb(Zn1/3Nb2/3)O3-xPbTiO3 investigated by dielectric and Raman spectroscopies

Lead zinc niobate-lead titanate[(1−x)Pb(Zn_1/3Nb_2/3)O₃-xPbTiO₃] (PZN-PT) crystals with x=4.5% and x=12% have been investigated using dielectric and Raman measurements over a range of temperatures. Above room temperature, dielectric measurements show that both compositions exhibit structural phase transitions according to the phase diagram proposed by Kuwata et al. [Ferroelectrics 387 (1981) 579]. Below room temperature, an anomaly at around 180 K for the x=12% sample is observed, suggesting another phase transition. Raman measurements are used to study all phase transitions.     

Electric field effects on the dielectric and acoustic anomalies of Pb[(Mg1/3Nb2/3)0.83Ti0.17]O3 single crystals studied by dielectric and Brillouin spectroscopies

The effect of the electric field on the dielectric and acoustic properties of Pb[(Mg_1/3Nb_2/3)_0.83Ti_0.17]O₃ single crystals was investigated as functions of temperature and the electric field strength. The dielectric constant and the acoustic mode behaviors exhibited typical relaxor behaviors when there was no bias field. The longitudinal acoustic mode showed splitting under a moderate electric field of 1 kV/cm applied along the [001] direction, indicating coexistence of macroscopic/mesoscopic ferroelectric states and relaxor states. Further increase in the electric field up to 2 kV/cm induced a clear ferroelectric phase transition, which became smeared out due to the proximity of the electric field to the critical point. The electric field-temperature phase diagram of Pb[(Mg_1/3Nb_2/3)_0.83Ti_0.17]O₃ was suggested based on the observed field-induced changes in the dielectric and the acoustic properties.