Photoelectrochemical properties of electrochemically deposited CdIn2S4 thin films

Thin films of CdIn₂S₄ have been deposited on to stainless steel and fluorine-doped tin oxide (FTO)-coated glass substrates from aqueous acidic bath using an electrodeposition technique. Ethylene diamine tetra-acetic acid (EDTA) disodium salt is used as complexing agent to obtain good-quality deposits by controlling the rate of the reaction. The different preparative parameters like concentration of bath, deposition time, bath temperature, pH of the bath have been optimized by the photoelectrochemical (PEC) technique in order to get good-quality photosensitive material. Different techniques have been used to characterize CdIn₂S₄ thin films. Optical absorption shows the presence of direct transition with band gap energy 2.17 eV. The X-ray diffraction (XRD) analysis of the as-deposited and annealed films showed the presence of polycrystalline nature. Energy-dispersive analysis by X-ray (EDAX) study for the sample deposited at optimized preparative parameters shows that the In-to-Cd ratio is almost 2 and S-to-Cd ratio is almost 4. Scanning electron microscopy (SEM) for samples deposited at optimized preparative parameters reveals that spherical grains are uniformly distributed over the surface of the substrate indicates the well-defined growth of polycrystalline CdIn₂S₄ thin film. PEC characterization of the films is carried out by studying photoresponse, spectral response and photovoltaic output characteristics. The fill factor (ff) and power conversion efficiency (η) of the cell are 69 and 2.94%, respectively.     

Annealing temperature influence on electrical properties of ion beam sputtered Bi2Te3 thin films

Ion beam sputtering process was used to deposit n-type fine-grained Bi₂Te₃ thin films on BK7 glass substrates at room temperature. In order to enhance the thermoelectric properties, thin films are annealed at the temperatures ranging from 100 to 400 °C. X-ray diffraction (XRD) shows that the films have preferred orientations in the c-axis direction. It is confirmed that grain growth and crystallization along the c-axis are enhanced as the annealing temperature increased. However, broad impurity peaks related to some oxygen traces increase when the annealing temperature reached 400 °C. Thermoelectric properties of Bi₂Te₃ thin films were investigated at room temperature. The Bi₂Te₃ thin films, including as-deposited, exhibit the Seebeck coefficients of −90 to −168 μV K⁻¹ and the electrical conductivities of 3.92×10²-7.20×10² S cm⁻¹ after annealing. The Bi₂Te₃ film with a maximum power factor of 1.10×10⁻³ Wm⁻¹ K⁻² is achieved when annealed at 300 °C. As a result, both structural and transport properties have been found to be strongly affected by annealing treatment. It was considered that the annealing conditions reduce the number of potential scattering sites at grain boundaries and defects, thus improving the thermoelectric properties.     

The morphology and structural properties of InP thin films deposited by spray pyrolysis method

InP film samples were prepared by spray pyrolysis technique using aqueous solutions of InCl₃ and Na₂HPO₄, which were atomized with compressed air as carrier gas onto glass substrates at 500 °C with different thicknesses of the films. The structural properties of the samples have been determined by using X-ray diffraction (XRD). It was found that the crystal structure of the InP films is polycrystalline hexagonal. The orientations for all the obtained films are along the c-axis perpendicular to the substrate. It is observed that the crystallite sizes of the films increase with the thickness of the film up to 616 nm. The changes observed in the morphology and structural phases related to the film thickness have been discussed in detail.     

Properties of In2S3 thin films deposited onto ITO/glass substrates by chemical bath deposition

In₂S₃ films have been chemically deposited on ITO coated glass substrates by chemical bath deposition, using different deposition times and precursor concentrations. The bilayers are intended for photovoltaic applications. Different characterization methods have been employed: optical properties of the films were investigated from transmittance measurements, structural properties by XRD and micro-Raman, and surface morphology by SEM microscopy analysis. Also, the direct and indirect band-gaps and the surface gap states were studied with surface photovoltage spectroscopy (SPS). We proposed that electronic properties of the In₂S₃ samples are controlled by two features: shallow tail states and a broad band centred at 1.5 eV approximately. Their relation with the structure is discussed, suggesting that their origin is related to defects created on the S sub-lattice, and then both defects are intrinsic to the material.     

Polymorphism in Cu-substituted GaV4S8: structural and electronic properties

The hexagonal and cubic phases of Ga_1−xCu_xV₄S₈ are obtained by different methods of preparation. The reaction of elements above 900 °C gives hexagonal phases for large range of x=0.02-0.5. These are metallic and show enhanced paramagnetism. The reduction of oxides by H₂S at a lower temperature of 700 °C gives non-stoichiomertic compositions of cubic-V₄ cluster compound GaV₄S₈. The solubility of Cu-atoms in cubic phase is less than 10% and above x=0.2 the samples contain a mixture of phases, Cu_xVS₂, Ga_xVS₂ and CuGaS₂. The cubic phases are insulating and show Mott's Variable Range Hopping conduction. The non-stoichiomerty and the Cu-substitution reduce the resistivity and thermopower. For x=0.15 and 0.20, the additional peaks are observed in X-ray patterns. These compositions showed a sharp metal to insulator transition on cooling below 180 K. The transitional behaviour is very similar to that previously reported intercalated VS₂ compound Al_xVS₂. The transport and magnetic properties of these phases are discussed in terms of the clustering interactions among V-atoms and the localisation of carriers on the metallic clusters frequently found in V-chalcogenides.     

Photocatalytic H2 evolution under visible light irradiation on AgIn5S8 photocatalyst

A new visible-light-driven photocatalyst AgIn₅S₈ was prepared by a simple two-step process, which involves the first co-precipitation process at room temperature and subsequently heat-treatment process at 750 °C under pure argon flow protection. The obtained AgIn₅S₈ sample showed high activity for the evolution of hydrogen under visible light irradiation (λ?420 nm) from aqueous solution containing S²⁻ and SO₃²⁻ ions as sacrificial electron donors. It was found that several experimental parameters, such as the concentration of sacrificial reagents and the loading of Pt co-catalyst, play important roles on the evolution rate of H₂ under visible light irradiation.     

Electrical conduction and optical properties of amorphous (Sb2Se3)100−xSnx thin films

The variation of DC electrical conductivity and the optical properties of thermally evaporated a- (Sb₂Se₃)_100−xSn_x thin films with temperature have been studied. It is found that the thermal activation energy decreases, while the optical gap first increases (up to x=1) and then decreases, with the increase in Sn content. These results have been explained by taking into consideration the structural modifications induced by the incorporation of Sn into the parent alloy. The variation in the conductivity prefactor (σ_o) with Sn addition indicates a change in the dominant conduction transport mechanism from extended states to localized states. An experimental correlation between the activation energy and the pre-exponential factor has been observed, indicating the validity of Meyer–Neldel rule in the studied samples.     

Effects of annealing temperature on the structural and photoluminescence properties of nanocrystalline ZrO2 thin films prepared by sol-gel route

Highly transparent nanocrystalline zirconia thin films were prepared by the sol-gel dip coating technique. XRD pattern of ZrO₂ thin film annealed at 400 °C shows the formation of tetragonal phase with a particle size of 13.6 nm. FT-IR spectra reveal the formation of Zr-O-Zr and the reduction of OH and other functional groups as the temperature increases. The transmittance spectra give an average transmittance greater than 80% in the film of thickness 262 nm. Photoluminescence (PL) spectra give intense band at 391 nm and a broad band centered at 300 nm. The increase of PL intensity with elevation of annealing temperature is related to reduction of OH groups, increase in the crystallinity and reduction in the non-radiative related defects. The luminescence dependence on defects in the film makes it suitable for luminescent oxygen-sensor development. The “Red shift” of excitation peak is related to an increase in the oxygen content of films with annealing temperature. The “Blue shift” of PL spectra originates from the change of stress of the film due to lattice distortion. The defect states in the nanocrystalline zirconia thin films play an important role in the energy transfer process.     

Effect of Ga incorporation on valence band splitting of OVC CuIn3Se5 thin films

Polycrystalline thin films of CuIn_2.95Ga_0.05Se₅ produced by the incorporation of Ga into the ordered vacancy compound CuIn₃Se₅ by a two-stage vacuum evaporation process were structurally, compositionally and optically characterized using X-ray diffraction, energy dispersive analysis of X-rays and optical absorbance measurements. From the X-ray diffraction data of the films, the structural parameters like lattice constants, tetragonal deformation, bond lengths and anion displacement were evaluated and their effect on the optical behavior of films was discussed. The Hopfields quasi-cubic model adapted for chalcopyrites with tetragonal deformation was used to elucidate the crystal field and spin orbital splitting parameters in the uppermost valence band of the compound, using the three energy gaps 1.649, 1.718 and 1.92 eV corresponding to the threefold absorption in the fundamental absorption region of the optical spectra of these films. The percentage contributions of Se p and Cu d orbitals to p-d hybridization in this compound were calculated using linear hybridization of orbitals model and the effects of p-d hybridization on the band gaps were studied.     

Structure-related infrared optical properties of BaTiO3 thin films grown on Pt/Ti/SiO2/Si substrates

BaTiO₃ thin films with different thickness have been grown on Pt/Ti/SiO₂/Si substrates by a modified sol-gel method. X-ray diffraction analyses show that the BaTiO₃ thin films are polycrystalline. The crystalline quality of the films is improved with increasing thickness. The infrared optical properties of the BaTiO₃ thin films have been investigated using an infrared spectroscopic ellipsometry in the wave number range of 800-4000 cm⁻¹ (2.5-12.5 μm). By fitting the measured pseudodielectric functions with a three-phase model (Air/BaTiO₃/Pt), and a derived classical dispersion relation for the thin films, the optical constants and thicknesses of the thin films have been simultaneously obtained. The refractive index of the BaTiO₃ thin films increases and on the other hand, the extinction coefficient does not change with increasing thickness in the entirely measured wave number range. The dependence of the refractive index on the film thickness has been discussed in detail and was mainly due to both the crystalline quality of the films and packing density. Finally, the absorption coefficient was calculated in the infrared region for applications in the pyroelectric IR detectors.     

Piezoelectric non-linearity in PbSc0.5Ta0.5O3 thin films

Epitaxial (001)-oriented PbSc_0.5Ta_0.5O₃ (PST) thin films were deposited by pulsed laser deposition. Local piezoelectric investigations performed by piezoelectric force microscopy show a dual slope for the piezoelectric coefficient. A piezoelectric coefficient of 3 pm/V was observed at voltages up to 0.8 V. However, at voltages above 0.8 V, there is a steep increase in piezoelectric coefficient mounting to 23.2 pm/V. This nonlinear piezoelectric response was observed to be irreversible in nature. In order to better understand this nonlinear behavior, voltage dependent dielectric constant measurements were performed. These confirmed that the piezoelectric non-linearity is indeed a manifestation of a dielectric non-linearity. In contrast to classical ferroelectric systems, the observed dielectric non-linearity in this relaxor material cannot be explained by the Rayleigh model. Thus the dielectric non-linearity in the PST films is tentatively explained as a manifestation of a percolation of the polar nano regions.     

Orientation-dependent dielectric properties of Ba(Sn0.15Ti0.85)O3 thin films prepared by sol-gel method

The orientation-dependent dielectric properties of barium stannate titanate (Ba(Sn_0.15Ti_0.85)O₃, BTS) thin films grown on (1 0 0) LaAlO₃ single-crystal substrates through sol-gel process were investigated. The nonlinear dielectric properties of the BTS films were measured using an inter-digital capacitor (IDC). The results show that the in-plane dielectric properties of BTS films exhibited a strong sensitivity to orientation. The upward shift of Curie temperature (T_c) of the highly (1 0 0)-oriented BTS thin films is believed to be attributing to a tensile stress along the in-plane direction inside the film. A high tunability of 47.03% was obtained for the highly (1 0 0)-oriented BTS films, which is about three times larger than that of the BTS films with random orientation, measured at a frequency of 1 MHz and an applied electric field of 80 kV/cm. This work clearly reveals the highly promising potential of BTS films for application in tunable microwave devices.     

Superconducting properties in Rh17S15 under magnetic field and pressure

We have studied superconducting properties by measuring the electrical resistivity and magnetization for a single crystal of Rh₁₇S₁₅ with a superconducting transition temperature T_c=5.4 K. The upper critical field H_c2(0) and the lower critical field H_c1(0) were obtained as 20.5 and 0.0033 T, respectively. Correspondingly, the coherence length and the penetration depth were estimated to be 40 and 4900 Å, respectively, indicating that Rh₁₇S₁₅ is a typical type-II superconductor with strong correlations of conduction electrons with a 4d-electron character of Rh atoms. The present electron correlations are formed to be enhanced with increasing pressure.     

Structural, electrical and optical properties of AgInS2 thin films grown by thermal evaporation method

Structural electrical and optical properties of AgInS₂ (AIS) thin films grown by the single-source thermal evaporation method were studied. The X-ray diffraction spectra indicated that the AIS single phase was successful grown by annealing above 400 °C in air. The AIS grain sizes became large with increasing the annealing temperatures. All polycrystalline AIS thin films were sulfur-poor from the electron probe microanalysis and indicated n-type conduction by the Van der Pauw technique. It was deduced that the sulfur vacancies were dominant in the films and enhanced n-type conduction.     

Influence of deposition pressure on structural, optical and electrical properties of nc-Si:H films deposited by HW-CVD

Hydrogenated nanocrystalline silicon (nc-Si:H) thin films were deposited using HW-CVD technique at various deposition pressures. Characterisation of these films from Raman spectroscopy revealed that nc-Si:H thin films consist of a mixture of two phases, crystalline phase and amorphous phase containing small Si crystals embedded therein. We observed increase in crystallinity in the films with increase in deposition pressure whereas the size of Si nanocrystals was found ∼2 nm over the entire range of deposition pressure studied. The FTIR spectroscopic analysis showed that with increasing deposition pressure the predominant hydrogen bonding in the films shifts from, Si-H to Si-H₂ and (Si-H₂)_n complexes and the hydrogen content in the films was found in the range 6.2-9.3 at% over the entire range of deposition pressure studied. The photo and dark conductivities results also indicate that the films deposited with increasing deposition pressure get structurally modified. It has been found that the optical energy gap range was between 1.72 and 2.1 eV with static refractive index between 2.85 and 3.24. From the present study it has been concluded that the deposition pressure is a key process parameter to induce the crystallinity in the Si:H thin films using HW-CVD.     

Structure, thermally and optically induced effects in amorphous As2Se3 films prepared by pulsed laser deposition

Thin amorphous As-Se films were prepared by pulsed laser deposition (PLD) and by classical thermal evaporation techniques. Raman spectra and optical properties (optical gap, E_g^opt, index of refraction, n, third-order non-linear susceptibility, χ⁽³⁾) of prepared films and their photo- and thermally induced changes were studied. The structure of laser deposited films was close to the corresponding bulk glasses contrary to thermal evaporated films. The composition of PLD films was practically unchanged during the process of deposition. The optically and thermally induced changes of n and of E_g^opt in PLD films are different from the changes in thermally deposited films. The differences are discussed.     

Evolution of structural and optical properties of rutile TiO2 thin films synthesized at room temperature by chemical bath deposition method

Nanocrystalline thin films of TiO₂ were prepared on glass substrates from an aqueous solution of TiCl₃ and NH₄OH at room temperature using the simple and cost-effective chemical bath deposition (CBD) method. The influence of deposition time on structural, morphological and optical properties was systematically investigated. TiO₂ transition from a mixed anatase–rutile phase to a pure rutile phase was revealed by low-angle XRD and Raman spectroscopy. Rutile phase formation was confirmed by FTIR spectroscopy. Scanning electron micrographs revealed that the multigrain structure of as-deposited TiO₂ thin films was completely converted into semi-spherical nanoparticles. Optical studies showed that rutile thin films had a high absorption coefficient and a direct bandgap. The optical bandgap decreased slightly (3.29–3.07 eV) with increasing deposition time. The ease of deposition of rutile thin films at low temperature is useful for the fabrication of extremely thin absorber (ETA) solar cells, dye-sensitized solar cells, and gas sensors.     

Effect of Bi substitution on the magnetic and dielectric properties of epitaxially grown BaFe0.3Zr0.7O3−δ thin films on SrTiO3 substrates

The structural, dielectric and magnetic properties of single crystalline Ba_1−xBi_xFe_0.3Zr_0.7O_3−δ (x=0.0-0.29) thin films have been studied. The pseudotetragonal epitaxial thin films were obtained by pulsed laser-beam deposition (PLD) on (0 0 1) SrTiO₃ (STO) single-crystal substrates. The Bi substitution for the Ba ions up to an extent of x=0.18 caused a slight improvement in the leakage current properties, as well as an enhancement of the apparent dielectric constant. The saturation magnetization of the films was significantly decreased following Bi substitution. These changes were thought to be related to the increase in oxygen deficiencies in the films. The effect of the Bi substitution on the dielectric and magnetic properties was analyzed in conjunction with the change in valence value of the Fe ions.     

Influence of cation substitution on the magnetic properties of the FeCr2S4 ferrimagnet

The influence of cation substitution on the magnetic properties of single and polycrystals of FeCr₂S₄ spinel has been studied. The tetrahedral A-site substitution of the Fe by Cu in Fe_1−xCu_xCr₂S₄ was found to increase significantly the value of temperature T_m of the spin-glass like magnetization anomaly, whereas the octahedral B-site substitution of the Cr by In decreases T_m. This effect is suggested to result from a structural transformation influenced by variation of internal (chemical) pressure due to lattice contraction (Cu) or expansion (In). The observed reduced values of the Curie temperature for Cu-substituted single crystals compared to that of the polycrystalline samples are attributed to presence of Cl ions in samples detected by electron-probe microanalysis. The observed reduced value of saturation magnetization in the polycrystals compared to the single crystals is ascribed to the effect of surface anisotropy. Based on the experimental data the superexchange is concluded to be the dominant exchange interaction for 0≤x≤0.5 in Fe_1−xCu_xCr₂S₄, whereas the indirect exchange through the charge carriers is considered of minor importance.     

Characterization of Cu(In,Ga)Se2 thin films prepared by evaporationfrom ternary compounds

Thin films of Cu(In,Ga)Se₂ were fabricated by evaporation from ternary CuGaSe₂ and CuInSe₂ compounds for photovoltaic device applications and their properties were investigated. From XRF analysis, the Cu:(In+Ga):Se atomic ratio in all thin films was approximately 1:1:2. The Ga/(In+Ga) atomic ratio in the thin films changed linearly from 0 to 1.0 with increasing the [CGS]/([CGS]+[CIS]) mole ratio in the evaporating materials. However, for thin films prepared at the [CGS]/([CGS]+[CIS]) mole ratio above 0.4, the composition by EPMA analysis was not consistent with that by XRF analysis. The result of EPMA analysis showed that the surface of a thin film was Cu-rich. XRD studies demonstrated that the thin films prepared at the [CGS]/([CGS]+[CIS]) mole ratio under 0.2 had a chalcopyrite Cu(In,Ga)Se₂ structure and the preferred orientation to the 112 plane. On the other hand, XRD patterns of the thin films produced at the [CGS]/([CGS]+[CIS]) mole ratio above 0.6 showed the diffraction lines from a chalcopyrite Cu(In,Ga)Se₂ and a foreign phase. The separation of a peak was observed near 2θ=27°, indicative the graded Ga concentration in Cu(In,Ga)Se₂ thin film.