TbMnO3 epitaxial thin films by pulsed-laser deposition

Epitaxial TbMnO₃ films have been fabricated on SrTiO₃(001) and LaAlO₃(001) substrates by pulsed laser deposition (PLD), the structure and surface morphology of the films were characterized by X-ray diffraction with Cu K_α radiation and atomic force microscopy. The electrical transport and magnetic properties of the TbMnO₃ films and bulk were examined, the resistivity and the forbidden band width E_g change with epitaxial orientation, semiconductor transport properties are found in the films and bulk, the average of the E_g of the films on SrTiO₃ and on LaAlO₃ is equal to the E_g of the bulk. The two TMO films have different magnetization mode, the magnetization of the film on SrTiO₃ have an analogy to that of TbMnO₃ single crystal.     

The ferroelectric field effect on the two-dimensional electron gas at LaAlO3/SrTiO3 (001) interface: Insights from first principle simulations

We perform first-principles calculations to explore the possibility of tuning the two-dimensional electron gas at the LaAlO₃/SrTiO₃ (001) interface through BaTiO₃ substrate. A metal-to-insulator transition is found at the interface as the polarization of BaTiO₃ reverses. Through the potential analysis of the LaAlO₃/SrTiO₃/BaTiO₃ superstructure, we find that the intrinsic electric field of LaAlO₃ is significantly suppressed as the polarization points away from the LaAlO₃/SrTiO₃ interface, while it is enhanced with the polarization pointing to the interface. The ferroelectric field control of the intrinsic electric field, and therefore the electronic reconstructions at the interface, originating from the screening of polarization charges, opens the way to the development of novel nanoscale electronic devices.     

氧压对SrTiO3和SrNb0.2Ti0.8O3薄膜晶格参数的影响及激光感生热电电压效应

采用脉冲激光沉积技术制备了SrTiO₃和SrNb_0.2Ti_0.8O₃薄膜.X射线衍射分析表明在LaAlO₃(100)单晶平衬底上生长的SrTiO₃及SrNb_0.2Ti_0.8O₃薄膜是沿［001］取向的近外延生长.随着氧压在一定范围内逐渐增大,SrTiO₃薄膜的晶格参数减小,而SrNb_0.2Ti_0.8O₃薄膜的晶格参数先减小后增大.同时摸索出制备具有二维电子气超晶格(SrTiO₃/SrNb_0.2Ti_0.8O₃)_L的最佳氧压为1.0×10^-2Pa.另外在LaAlO₃(100)倾斜衬底上制备的SrNb_0.2Ti_0.8O₃薄膜中观察到激光感生热电电压效应. 关键词： 0.2Ti_0.8O₃薄膜')" href="#">SrNb_0.2Ti_0.8O₃薄膜 晶格参数 激光感生热电电压 脉冲激光沉积     

La0.5Sr0.5CoO3薄膜的外延生长及其机理研究

利用脉冲激光制膜法,在多种衬底和温度条件下,系统研究了La_0.5Sr_0.5CoO₃(LSCO)薄膜的结构和外延生长特性,在LaAlO₃,SrTiO₃和MgO衬底上实现了LSCO薄膜的外延生长.外延生长的薄膜具有低的电阻率和金属性导电特征.研究表明,外延生长的最佳温度范围为700—800℃,最佳衬底为LaAlO₃.并着重探讨了衬底材料和淀积温度等多种因素对LSCO薄膜的生长与性 关键词：     

Impurity induced resonance states at the superconducting interface LaAlO3/SrTiO3

Motivated by the recent discovery of superconductivity on the heterointerface LaAlO₃/SrTiO₃, we theoretically investigate the impurity-induced resonance states with coexisting spin singlet s- and triplet p-wave pairing symmetries by considering the influence of Rashba-type spin-orbit interaction (RSOI). Due to the nodal structure of the mixed gap function, we find single nonmagnetic impurity-induced resonance peaks appearing in the local density of state. We also analyze the evolutions of density of states and local density of states with the weight of triplet pairing component determined by the strength of RSOI, which will be widely observed in thin films of superconductors with surface or interface-induced RSOI, or various noncentrosymmetric superconductors in terms of point contact tunneling and scanning tunneling microscopy, and thus shed light on the admixture of the spin singlet and RSOI-induced triplet superconducting states.     

Band offsets of epitaxial LaAlO3/TiO2 interface determined by X-ray photoelectron spectroscopy

Room-temperature ferromagnetism in doped anatase TiO₂ has previously been observed, ferromagnetic semiconductor heterostructures based on anatase TiO₂ can thus provide a new opportunity to study spin-dependent transport phenomena at room temperature. An accurate determination of barrier heights or band offsets at the TiO₂-based heterojunctions is of great importance for the spintronics application with semiconductors. X-ray photoelectron spectroscopy with high-energy resolution was used to determine the band offsets of epitaxial LaAlO₃/TiO₂ heterojunction on SrTiO₃(001) substrate fabricated by pulsed laser deposition. Results showed an upward band bending of 0.48(0.03) eV when the film thickness of the overlayer LaAlO₃ above 4 unit cells. The valence band offset obtained is about 0.35(0.16) eV. Assuming bulk band gaps for the LaAlO₃ and TiO₂ epitaxial films, the associated conduction band offset is about 2.95(0.16) eV. These results show that LaAlO₃ can be an ideal tunneling barrier for TiO₂-based heterojunctions.     

Unusual resistive switching induced by voltage in La0.7Sr0.3MnO3 thin films

The hysteretic and reversible resistive-switching effect was observed in La_0.7Sr_0.3MnO₃ films at room temperature. The resistive switching was found to be most obvious in films fabricated at 30 Pa oxygen pressure, and more distinct in films fabricated on SrTiO₃ substrates than those fabricated on LaAlO₃ substrates. Moreover, La_0.7Sr_0.3MnO₃ films fabricated at a certain oxygen pressure with indium electrodes showed double ‘8’ type current-voltage loops. Some of the results are explained by considering the influence of the interface effect, electrodes and oxygen vacancies, but the mechanism of the double ‘8’ type current-voltage loops remains an open question.     

Effect of polar distortion on electronic structures of (001) LaGaO3/SrTiO3 interface

First-principles calculations of electronic structures of (001) epitaxial LaGaO₃/SrTiO₃ heterostructures were performed in the framework of density functional theory. The effects of atomic relaxation on electronic characteristics of both n-type (LaO)⁺/(TiO₂)⁰ and p-type (GaO₂)⁻/(SrO)⁰ interfaces are investigated. It is found that the n-type interface remains metallic, whereas the p-type interface becomes insulating after atomic relaxation. Polar distortion in the LaGaO₃ layers associated with the atomic relaxation strongly screens the intrinsic electric field induced by periodically stacking (LaO)⁺ and (GaO₂)⁻ charged atomic layers on SrTiO₃ with charge neutral (001) atomic layers. This relieves the trend to a polar catastrophe and reduces the carrier charge density on the interface.     

Instability,intermixing and electronic structure at the epitaxial LaAlO3/SrTiO3(001) heterojunction

The question of stability against diffusional mixing at the prototypical LaAlO₃/SrTiO₃(001) interface is explored using a multi-faceted experimental and theoretical approach. We combine analytical methods with a range of sensitivities to elemental concentrations and spatial separations to investigate interfaces grown using on-axis pulsed laser deposition. We also employ computational modeling based on the density function theory as well as classical force fields to explore the energetic stability of a wide variety of intermixed atomic configurations relative to the idealized, atomically abrupt model. Statistical analysis of the calculated energies for the various configurations is used to elucidate the relative thermodynamic stability of intermixed and abrupt configurations. We find that on both experimental and theoretical fronts, the tendency toward intermixing is very strong. We have also measured and calculated key electronic properties such as potential energy gradients and valence band discontinuity at the interface. We find no measurable electric field in either the LaAlO₃ or SrTiO₃, and that the valence band offset is near zero, partitioning the band discontinuity almost entirely to the conduction band edge. Significantly, we find it is not possible to account for these electronic properties theoretically without including extensive intermixing in our physical model of the interface. The atomic configurations which give the greatest electrostatic stability are those that eliminate the interface dipole by intermixing, calling into question the conventional explanation for conductivity at this interface—electronic reconstruction. Rather, evidence is presented for La indiffusion and doping of the SrTiO₃ below the interface as being the cause of the observed conductivity.     

Epitaxial growth and characterization of CaVO3 thin films

Epitaxial thin films of CaVO₃ were synthesized on SrTiO₃, LaAlO₃ and (La_0.27Sr_0.73)(Al_0.65Ta_0.35)O₃ substrates by pulsed laser deposition. All CaVO₃ films, independent of epitaxial strain, exhibit metallic and Pauli paramagnetic behavior as CaVO₃ single crystals. X-ray absorption measurements confirmed the 4+ valence state for Vanadium ions. With prolonged air exposure, an increasing amount of V³⁺ is detected and is attributed to oxygen loss in the near surface region of the films.     

Combinatorial synthesis and optical characterization of alloy and superlattice films based on SrTiO3 and LaAlO3

We have grown alloy and superlattice films consisting of SrTiO₃ (STO) and LaAlO₃ (LAO) by pulsed laser deposition using composition-spread technique. All the (STO)_x(LAO)_1−x (0 ≤ x ≤ 1) alloy and superlattice films exhibited a single-phase perovskite structure. The optical properties of these films were characterized by absorption spectroscopy at room temperature. The spectra show a broad absorption due to O 2p-Ti 3d(t_2g) transition in an ultraviolet region. We found that absorption edges of both alloy and superlattice films systematically shifted to higher energy with increasing LAO composition. Clear difference was observed in the composition dependence of the indirect and a direct band edges.     

Magnetism without magnetic ions in non-magnetic perovskites SrTiO3, SrZrO3 and SrSnO3

Using the full-potential linearized augmented plane-wave (FP-LAPW) method with the generalized gradient approximation (GGA) for the exchange-correlation potential, we studied spin polarization induced by replacement of oxygen atoms by non-magnetic 2p impurities (B, C and N) in non-magnetic cubic SrMO₃ perovskites, where M=Ti, Zr and Sn. The results show that the magnetization may appear because of the spin–split impurity bands inside the energy gap of the insulating SrMO₃ matrix. Large magnetic moments are found for the impurity centers. Smaller magnetic moments are induced on the oxygen atoms around impurities. It is shown that SrTiO₃:C and SrSnO₃:C should be magnetic semiconductors while other compounds in this series (SrTiO₃:B, SrTiO₃:N and SrZrO₃:C) are expected to exhibit magnetic half-metallic or pseudo-half-metallic properties.     

Structural relaxation and metal-insulator transition at the interface between SrTiO3 and LaAlO3

The electronic structure of interfaces between LaAlO₃ and SrTiO₃ is studied using local spin density approximation (LSDA) with intra-atomic Coulomb repulsion (LSDA + U). We find that the nature of the interface metallic states is strongly affected by the type of the structure (sandwich or bilayer) and by the termination surface of LaAlO₃. In all structures the atomic relaxation plays a crucial role in the electronic properties of the system. While in sandwiches the structural relaxation produces a significant polarization in SrTiO₃ and a splitting of Ti 3d_xy orbitals, in AlO₂-terminated bilayers the relaxation occurs primarily in LaAlO₃ and results in an insulator-metal transition which has been observed experimentally with increasing thickness of the LaAlO₃ layer.     

Stable pH sensitivity of LaAlO3/SrTiO3 interfacial electronic gas

Probing pH value is essential for many applications. The request of developing stable and highly sensitive pH sensor with small size are increased recently, this is a challenge to the traditional glass pH sensors. This work investigated the pH sensing performance of the novel two-dimensional electronic gas (2DEG) at the LaAlO₃/SrTiO₃ heterostructure interface discovered recently. The experimental results demonstrated that the devices host excellent sensing ability to the pH value of aqueous solutions. Quite stable output current is realized for a given pH value, and the output current is linearly dependent on pH value as required by sensor applications. This work would prompt the application research of LaAlO₃/SrTiO₃ heterostructure and design of new generation of advanced pH sensors.     

Growth and structure of MBE grown TiO2 anatase films with rutile nano-crystallites

We have explored the systematics of TiO₂ polymorph nucleation during film growth by molecular beam epitaxy on perovskite substrates. The accidental lattice match between anatase (0 0 1) and LaAlO₃(0 0 1) or SrTiO₃(0 0 1) typically results in anatase nucleation at the interface. However, the growth conditions dictate whether or not rutile also nucleates, and the associated morphological and structural properties of the composite film. Four symmetry equivalent epitaxial orientations of rutile on anatase are observed when rutile nucleates as discrete particles on LaAlO₃(0 0 1). Such films constitute model systems for studying the anatase/rutile interface, which is of considerable current interest in photochemistry.     

Ferroelectricity in SrTiO3 nanocrystalline disks

SrTiO₃ and CaTiO₃ conventional bulk materials are incipient ferroelectrics. In this note, we report for the first time that ferroelectricity could occur in SrTiO₃ nanocrystalline disks even at room temperature. The peak in the temperature dependence of permittivity for a CaTiO₃ nanocrystalline disk at a low temperature is also observed. The observed ferroelectricity (or permittivity peak) in SrTiO₃ (or CaTiO₃) nanocrystalline disks could be attributed to the strain effect.     

Preparation of Fe2O3/SrTiO3 composite powders and their photocatalytic properties

Fe₂O₃/SrTiO₃ composite powders have been prepared and their photocatalytic activities were investigated by photooxidizing methanol. These powders were characterized by ultraviolet (UV)-visible diffuse reflectance spectra, scanning electron microscope (SEM) and X-ray diffraction (XRD). The results showed that the Fe₂O₃/SrTiO₃ composite powders with optimum proportion exhibited higher photocatalytic activity than pure SrTiO₃, Fe₂O₃ and TiO₂ (P25) under visible light (λ>440 nm) irradiation. The SEM image of the composite powders showed that SrTiO₃ and Fe₂O₃ particles contacted well. Further research revealed that the calcination temperature is an important factor in the preparation of the composite powder with relatively high photocatalytic ability.     

Pulsed laser deposition and characterization of nitrogen-substituted SrTiO3 thin films

Nitrogen-substituted cubic perovskite-type SrTiO₃ thin films were deposited in a one-step process using pulsed reactive crossed beam laser ablation (PRCLA) and RF-plasma assisted pulsed laser deposition (RF-PLD). Both techniques yield preferentially oriented films on SrTiO₃(0 0 1), LaAlO₃(0 0 1) and MgO(0 0 1) substrates with the unit cell parameters within 0.390(5) < a < 0.394(9) nm. The nitrogen content is higher in films deposited by PRCLA (0.84-2.40 at.%) as compared to films deposited by RF-PLD with nitrogen plasma (0.10-0.66 at.%). PRCLA with an ammonia gas pulse leads to a higher nitrogen content compared to the films grown with a nitrogen gas pulse, while films deposited by RF-PLD with ammonia plasma reveal only minor nitrogen contents (<0.10 at.%). The amount of the incorporated nitrogen can be tuned by adjusting the deposition parameters. Films deposited by PRCLA have a lower roughness of 1-3 nm compared to 12-18 nm for the films grown by RF-PLD. PRCLA yields partially reduced films, which exhibit electronic conductivity, while films deposited by RF-PLD are insulating. There is also a pronounced influence of the substrate material on the resistivity of the films deposited by PRCLA: films grown on SrTiO₃ substrates exhibit a metallic-like behaviour, while the corresponding films grown on MgO and LaAlO₃ substrates reveal a metal-to-semiconductor/insulator transition. Nitrogen incorporation into the SrTiO₃ films results in an increased optical absorption at 370-500 nm which is associated with N(2p) localized states with the energy about 0.7 eV higher than the valence band energy in strontium titanate. The optical band gap energies in the studied N-substituted SrTiO₃ films are 3.35-3.40 eV.     

DFT study of Pt adsorption on low index SrTiO3 surfaces: SrTiO3(1 0 0), SrTiO3(1 1 1) and SrTiO3(1 1 0)

Density Functional Theory has been used to determine the energetically preferred structures of submonolayer, monolayer, and multilayer Pt films on both ideal terminations of SrTiO₃(1 0 0), SrTiO₃(1 1 1), and SrTiO₃(1 1 0). The strength of the resulting metal/metal oxide interfaces was characterized by the adsorption energy of the film and the film’s work of separation. The two polar surfaces, SrTiO₃(1 1 1) and SrTiO₃(1 1 0), form significantly stronger interfaces than the non-polar SrTiO₃(1 0 0) surface. Approximate criteria were applied to predict the growth mode of Pt on each surface.     

Resistive hysteresis and capacitance effect in NiFe2O4/SrTiO3: Nb(1 wt%) junctions

Epitaxial ultrathin NiFe₂O₄ films were deposited on 1 wt% Nb-doped SrTiO₃ (0 0 1) substrates by reactive cosputtering to form junctions with an area of ∼2 mm², and current-voltage curves show rectifying and asymmetrical hysteresis characteristics. The resistance calculated from the current-voltage curves is strongly voltage dependent, and the hysteretic loops with high and low resistive states were observed. The hysteretic loops are considered to stem from the capacitance effect of the highly resistive NiFe₂O₄ layer, which leads to charge accumulation at the interfaces. The results show that the interfaces of the junctions have a large areal capacitance of ∼100 nF/mm² from 300 to 120 K.