Certification of butyltins and phenyltins in marine sediment certified reference material by species-specific isotope-dilution mass spectrometric analysis using synthesized <Superscript>118</Superscript>Sn-enriched organotin compounds

A new marine sediment certified reference material, NMIJ CRM 7306-a, for butyltin and phenyltin analysis has been prepared and certified by the National Metrological Institute of Japan at the National Institute of Advanced Industrial Science and Technology (NMIJ/AIST). Candidate sediment material was collected at a bay near industrial activity in Japan. After air-drying, sieving, and mixing the material was sterilized with γ-ray irradiation. The material was re-mixed and packaged into 250 glass bottles (15 g each) and these were stored in a freezer at −30 °C. Certification was performed by use of three different types of species-specific isotope-dilution mass spectrometry (SSID–MS)—SSID–GC–ICP–MS, SSID–GC–MS, and SSID–LC–ICP–MS, with ¹¹⁸Sn-enriched organotin compounds synthesized from ¹¹⁸Sn-enriched metal used as a spike. The ¹¹⁸Sn-enriched mono-butyltin (MBT), dibutyltin (DBT), and tributyltin (TBT) were synthesized as a mixture whereas the ¹¹⁸Sn-enriched di-phenyltin (DPhT) and triphenyltin (TPhT) were synthesized individually. Four different extraction methods, mechanical shaking, ultrasonic, microwave-assisted, and pressurized liquid extraction, were adopted to avoid possible analytical bias caused by non-quantitative extraction and degradation or inter-conversion of analytes in sample preparations. Tropolone was used as chelating agent in all the extraction methods. Certified values are given for TBT 44±3 μg kg⁻¹ as Sn, DBT 51 ± 2 μg kg⁻¹ as Sn, MBT 67 ± 3 μg kg⁻¹ as Sn, TPhT 6.9 ± 1.2 μg kg⁻¹ as Sn, and DPhT 3.4 ± 1.2 μg kg⁻¹ as Sn. These levels are lower than in other sediment CRMs currently available for analysis of organotin compounds.     

Preparation and certification of arsenate [As(V)] reference material, NMIJ CRM 7912-a

Arsenate [As(V)] solution reference material, National Metrology Institute of Japan (NMIJ) certified reference material (CRM) 7912-a, for speciation of arsenic species was developed and certified by NMIJ, the National Institute of Advanced Industrial Science and Technology. High-purity As₂O₃ reagent powder was dissolved in 0.8 M HNO₃ solution and As(III) was oxidized to As(V) with HNO₃ to prepare 100 mg kg^-1 of As(V) candidate CRM solution. The solution was bottled in 400 bottles (50 mL each). The concentration of As(V) was determined by four independent analytical techniques—inductively coupled plasma mass spectrometry, inductively coupled plasma optical emission spectrometry, graphite furnace atomic absorption spectrometry, and liquid chromatography inductively coupled plasma mass spectrometry—according to As(V) calibration solutions, which were prepared from the arsenic standard of the Japan Calibration Service system and whose species was guaranteed to be As(V) by NMIJ. The uncertainties of all the measurements and preparation procedures were evaluated. The certified value of As(V) in the CRM is (99.53 ± 1.67) mg kg^-1 (k = 2).     

Certified sediment reference materials for trace element analysis from the National Metrology Institute of Japan (NMIJ)

Two types of sediment reference material (NMIJ 7302-a and 7303-a) for trace elements analysis have been prepared and certified by the National Metrology Institute of Japan in the National Institute of Advanced Industrial Science and Technology (NMIJ/AIST). The original materials were collected from a bay near industrial activity in Kyushu (NMIJ CRM 7302-a; marine sediment) and from Lake Biwa (NMIJ CRM 7303-a; lake sediment). The sediment materials were air-dried, sieved, homogenized, packaged in 1000 glass bottles (60 g each), and radiation sterilized. Certification of these CRM for trace elements was conducted by NMIJ, where each element was determined by at least two independent analytical techniques. Isotope-dilution inductively coupled plasma mass spectrometry (ICP–MS) was applied for certification of all the elements except mono-nuclide elements such as As and Co. Other techniques such as ICP–MS with quadrupole mass spectrometry and sector-field mass spectrometry, inductively coupled plasma atomic emission spectrometry (ICP–AES), and atomic absorption spectrometry (AAS), were also used. Certified values have been provided for 14 elements (Sb, As, Cd, Cr, Co, Cu, Pb, Hg, Mo, Ni, Se, Ag, Sn, and Zn) in both CRM.     

Preparation and certification of hijiki reference material, NMIJ CRM 7405-a, from the edible marine algae hijiki (Hizikia fusiforme)

A certified reference material, NMIJ CRM 7405-a, for the determination of trace elements and As(V) in algae was developed from the edible marine hijiki (Hizikia fusiforme) and certified by the National Metrology Institute of Japan (NMIJ), the National Institute of Advanced Industrial Science and Technology (AIST). Hijiki was collected from the Pacific coast in the Kanto area of Japan, and was washed, dried, powdered, and homogenized. The hijiki powder was placed in 400 bottles (ca. 20 g each). The concentrations of 18 trace elements and As(V) were determined by two to four independent analytical techniques, including (ID)ICP-(HR)MS, ICP-OES, GFAAS, and HPLC-ICP-MS using calibration solutions prepared from the elemental standard solution of Japan calibration service system (JCSS) and the NMIJ CRM As(V) solution, and whose concentrations are certified and SI traceable. The uncertainties of all the measurements and preparation procedures were evaluated. The values of 18 trace elements and As(V) in the CRM were certified with uncertainty (k = 2).     

Certified calibration solution reference material for the determination of perfluorooctane sulfonate from the National Metrology Institute of Japan (NMIJ)

A new calibration solution reference material for the determination of perfluorooctane sulfonate anion (PFOS) and its salts has been issued as a certified reference material (CRM) by the National Metrology Institute of Japan, National Institute of Advanced Industrial Science and Technology (NMIJ/AIST). The purity amount-of-substance fraction of raw material potassium perfluorooctane sulfonate (K-PFOS) was evaluated based on the results obtained using the freezing point depression method, and the purity mass fraction of the raw material was calculated using the average molar mass of impurities, the molar mass of K-PFOS, and the purity amount-of-substance fraction. The certified concentration of this CRM was obtained by multiplying the dilution ratio of the raw material in a prepared solution (methanol) determined from the gravimetric blending method by the purity of the raw material. The preparation concentration of K-PFOS as a certified value of NMIJ CRM 4220-a was determined to be 9.93?mg?kg^?1. In addition, the standard uncertainty of the certified value was evaluated from the purity evaluation as well as from sample inhomogeneity, instability, and preparation variation obtained from LC/MS measurements of different gravimetrically prepared solutions of the NMIJ CRM. Consequently, the expanded uncertainty was estimated to be 0.15?mg?kg^?1 with a coverage factor k?=?2 corresponding to the half-width of estimated confidence interval of approximately 95%.     

Sulfur standard solution for use in the determination of low sulfur concentration in liquid fuels

A sulfur reference solution at the 1 mg kg⁻¹ level, NMIJ CRM 4215-a, has been issued by the National Metrology Institute of Japan at the National Institute of Advanced Industrial Science and Technology (NMIJ/AIST). The intended use of this CRM is for the calibration of standards used in the determination of sulfur in liquid fuels. The certified value of this CRM was determined using the gravimetric blending method. Thiophene and toluene were chosen as the high purity sulfur compound and the dilution solvent, respectively. Measurements of the trace sulfur in the solvent were performed using the total sulfur analyzer with an enrichment system; the standard addition method was employed. When trace sulfur in the solvent was evaluated, the signal which appears with no sample injection was subtracted as the background.     

Certification of methylmercury in cod fish tissue certified reference material by species-specific isotope dilution mass spectrometric analysis

A new cod fish tissue certified reference material, NMIJ CRM 7402-a, for methylmercury analysis was certified by the National Metrological Institute of Japan in the National Institute of Advanced Industrial Science and Technology (NMIJ/AIST). Cod fish was collected from the sea close to Japan. The cod muscle was powdered by freeze-pulverization and was placed into 600 glass bottles (10 g each), which were sterilized with γ-ray irradiation. The certification was carried out using species-specific isotope dilution gas chromatography inductively coupled plasma mass spectrometry (SSID–GC–ICPMS), where ²⁰²Hg-enriched methylmercury (MeHg) was used as the spike compound. In order to avoid any possible analytical biases caused by nonquantitative extraction, degradation and/or formation of MeHg in sample preparations, two different extraction methods (KOH/methanol and HCl/methanol extractions) were performed, and one of these extraction methods utilized two different derivatization methods (ethylation and phenylation). A double ID method was adopted to minimize the uncertainty arising from the analyses. In order to ensure not only the reliability of the analytical results but also traceability to SI units, the standard solution of MeHg used for the reverse-ID was prepared from high-purity MeHg chloride and was carefully assayed as follows: the total mercury was determined by ID–ICPMS following aqua regia digestion, and the ratio of Hg as MeHg to the total Hg content was estimated by GC–ICPMS. The certified value given for MeHg is 0.58 ± 0.02 mg kg⁻¹ as Hg. Figure NMIJ CRM 7402-a: cod fish tissue for MeHg analysis     

Sediment certified reference materials for the determination of polychlorinated biphenyls and organochlorine pesticides from the National Metrology Institute of Japan (NMIJ)

Two marine sediment certified reference materials, NMIJ CRM 7304-a and 7305-a, have been issued by the National Metrology Institute of Japan in the National Institute of Advanced Industrial Science and Technology (NMIJ/AIST) for the determination of polychlorinated biphenyls (PCBs) and organochlorine pesticides (OCPs). The raw materials of the CRMs were collected from a bay near industrial activity in Japan. Characterization of these CRMs was conducted by NMIJ, where the sediments were analyzed using multiple analytical methods such as pressurized liquid extraction (PLE), microwave-assisted extraction (MAE), saponification, Soxhlet extraction, supercritical fluid extraction (SFE), and ultrasonic extraction; the target compounds were determined by one of the primary methods of measurements, isotope dilution–mass spectrometry (ID-MS). Certified values have been provided for 14 PCB congeners (PCB numbers 3, 15, 28, 31, 70, 101, 105, 138, 153, 170, 180, 194, 206, 209) and 4 OCPs (γ-HCH, 4,4′-DDT, 4,4′-DDE, 4,4′-DDD) in both CRMs. NMIJ CRM 7304-a has concentrations of the contaminants that are a factor of 2–15 greater than in CRM 7305-a. Both CRMs have information values for PCB homolog concentrations determined by collaborative analysis using a Japanese official method for determination of PCBs. The total PCB concentrations in the CRMs are approximately 920 and 86 μg kg⁻¹ dry mass respectively. Electronic supplementary material Supplementary material is available in the online version of this article at and is accessible for authorized users.     

Simultaneous multi-species determination of trimethyllead,monomethylmercury and three butyltin compounds by species-specific isotope dilution GC–ICP–MS in biological samples

An accurate and sensitive multi-species species-specific isotope dilution GC–ICP–MS method was developed for the simultaneous determination of trimethyllead (Me₃Pb⁺), monomethylmercury (MeHg⁺) and the three butyltin species Bu₃Sn⁺, Bu₂Sn²⁺, and BuSn³⁺ in biological samples. The method was validated by three biological reference materials (CRM 477, mussel tissue certified for butyltins; CRM 463, tuna fish certified for MeHg⁺; DORM 2, dogfish muscle certified for MeHg⁺). Under certain conditions, and with minor modifications of the sample pretreatment procedure, this method could also be transferred to environmental samples such as sediments, as demonstrated by analyzing sediment reference material BCR 646 (freshwater sediment, certified for butyltins). The detection limits of the multi-species GC–ICP–IDMS method for biological samples were 1.4 ng g⁻¹ for MeHg⁺, 0.06 ng g⁻¹ for Me₃Pb⁺, 0.3 ng g⁻¹ for BuSn³⁺ and Bu₃Sn⁺, and 1.2 ng g⁻¹ for Bu₂Sn²⁺. Because of the high relevance of these heavy metal alkyl species to the quality assurance of seafood, the method was also applied to corresponding samples purchased from a supermarket. The methylated lead fraction in these samples, correlated to total lead, varied over a broad range (from 0.01% to 7.6%). On the other hand, the MeHg⁺ fraction was much higher, normally in the range of 80–100%. Considering that we may expect tighter legislative limitations on MeHg⁺ levels in seafood in the future, we found the highest methylmercury contents (up to 10.6 μg g⁻¹) in two shark samples, an animal which is at the end of the marine food chain, whereas MeHg⁺ contents of less than 0.2 μg g⁻¹ were found in most other seafood samples; these results correlate with the idea that MeHg⁺ is usually of biological origin in the marine environment. The concentration of butyltins and the fraction of the total tin content that is from butyltins strongly depend on possible contamination, due to the exclusively anthropogenic character of these compounds. A broad variation in the butylated tin fraction (in the range of <0.3–49%) was therefore observed in different seafood samples. Corresponding isotope-labeled spike compounds (except for trimethyllead) are commercially available for all of these compounds, and since these can be used in the multi-species species-specific GC-ICP-IDMS method developed here, this technique shows great potential for routine analysis in the future.     

Characterization of certified reference material for quantification of polychlorinated biphenyls and organochlorine pesticides in fish

Fish certified reference material (CRM), NMIJ CRM 7404-a, for the analysis of polychlorinated biphenyls (PCBs) and organochlorine pesticides (OCPs) was developed by the National Metrology Institute of Japan, part of the National Institute of Advanced Industrial Science and Technology. Fish samples (Japanese seabass) used for the preparation of the CRM were collected from Tokyo Bay, and the edible part was freeze-dried, pulverized, sieved, homogenized, and sterilized by γ-irradiation. This sample is in the form of a powder comprising approximately 10 g stored in a brown glass bottle. The certification was carried out using multiple analytical methods such as pressurized liquid extraction, Soxhlet extraction, saponification, and homogenization to ensure the reliability of analytical results; the certified values of target PCBs (PCB 28, PCB 70, PCB 105, PCB 153, and PCB 170) and OCPs (trans-nonachlor, dieldrin, p,p′-DDE, p,p′-DDT, and p,p′-DDD) were 1.05–14.0 μg kg⁻¹ and 1.57–18.0 μg kg⁻¹ for PCBs and OCPs, respectively. This is the first fish powder CRM in which PCBs and OCPs were determined by isotope dilution mass spectrometry.     

Determination of <Superscript>90</Superscript>Sr in contaminated environmental samples by tuneable bandpass dynamic reaction cell ICP–MS

A rapid method for the extraction and determination of ⁹⁰Sr in natural water, plant and sediment samples was developed using extraction chromatography and dynamic reaction cell ICP–MS, with O₂ as a reaction gas. While isobaric interference from the stable isotope ⁹⁰Zr was efficiently removed by this method, interferences produced from in-cell reactions with Fe⁺ and Ni⁺ required suppression by tuneable bandpass, and in sediments, additional chromatographic separation. Method detection limits were 0.1 pg g⁻¹ (0.5 Bq g⁻¹), 0.04 pg g⁻¹(0.2 Bq g⁻¹), and 3 pg L⁻¹ (5 Bq L⁻¹) for sediments, plant and water samples, respectively, and ⁹⁰Sr concentrations determined by ICP–MS were in good agreement with activities determined by Cerenkov counting and with certified reference values. While mass spectrometric determination does not rival detection limits achievable by radiometric counting, radiometric determination of ⁹⁰Sr, a pure beta-emitter, is hindered by long analysis times (several weeks); the comparatively fast analysis achieved via ICP–MS enables same-day preparation and analysis of samples, making this an important technique for the environmental monitoring of areas contaminated by radioactivity.     

Determination of lead in sediments and sewage sludge by on-line hydride-generation axial-view inductively-coupled plasma optical-emission spectrometry using slurry sampling

Among the “traditional” hydride-forming elements, lead is probably the most difficult, and its determination in this form has rarely been reported in the literature. In this paper a simple and rapid method, axial-view inductively-coupled plasma optical-emission spectrometry using on-line hydride generation (HG–ICP–OES) from samples prepared as slurry, is proposed for determination of lead in environmental samples. The samples (20–50 mg, particle size ≤120 μm) were treated with 1 mL aqua regia in a 40-kHz ultrasonic bath for 60 min. The slurry was diluted to a final volume of 50 mL with a 10% m/v solution of (NH₄)₂S₂O₈. The concentrations of NaBH₄, tartaric acid, and (NH₄)₂S₂O₈, used for on-line plumbane generation were optimized by means of a complete factorial analysis applied to an aqueous standard solution and to the slurry of a sediment certified reference material (CRM). External calibration against aqueous standards in the concentration range 10–100 μg L⁻¹ was used for analysis of six CRM—three marine sediments, one river sediment, and two sewage sludges. Analysis of the filtered slurry showed that Pb was only partially extracted into the liquid phase. Several major concomitants tested did not affect the Pb signal. The detection limit (3s, n = 10) for 20 mg sample in a final volume of 50 mL was 5.0 μg g⁻¹. Tin was the only other hydride-forming analyte that could be determined satisfactorily with Pb; for tin the detection limit was 1.0 μg g⁻¹. The values obtained for Pb and Sn were not significantly different from the certified concentrations, according to the t-test at the 95% confidence level. Nine river sediments collected locally were also analyzed and the concentrations were in agreement with results obtained after total digestion.     

Direct determination of platinum group elements and their distributions in geological and environmental samples at the ng g<Superscript>−1</Superscript> level using LA–ICP–IDMS

Laser ablation inductively coupled plasma isotope dilution mass spectrometry (LA–ICP–IDMS) was applied to the direct and simultaneous determination of the platinum group elements (PGEs) Pt, Pd, Ru, and Ir in geological and environmental samples. A special laser ablation system with high ablation rates was used, along with sector field ICP–MS. Special attention was paid to deriving the distributions of PGEs in the pulverized samples. IDMS could not be applied to the (mono-isotopic) Rh, but the similar ablation behavior of Ru and Rh allowed Rh to be simultaneously determined via relative sensitivity coefficients. The laser ablation process produces hardly any oxide ions (which usually cause interference in PGE analysis with liquid sample injection), so the ICP–MS can be run in its low mass resolution but high-sensitivity mode. The detection limits obtained for the geological samples were 0.16 ng g⁻¹, 0.14 ng g⁻¹, 0.08 ng g⁻¹, 0.01 ng g⁻¹ and 0.06 ng g⁻¹ for Ru, Rh, Pd, Ir and Pt, respectively. LA–ICP–IDMS was applied to different geological reference materials (TDB-1, WGB-1, UMT-1, WMG-1, SARM-7) and the road dust reference material BCR-723, which are only certified for some of the PGEs. Comparisons with certified values as well as with indicative values from the literature demonstrated the validity of the LA–ICP–IDMS method. The PGE concentrations in subsamples of the road dust reference material correspond to a normal distribution, whereas the distributions in the geological reference materials TDB-1, WGB-1, UMT-1, WMG-1, and SARM-7 are more complex. For example, in the case of Ru, a logarithmic normal distribution best fits the analyzed concentrations in TDB-1 subsamples, whereas a pronounced nugget effect was found for Pt in most geological samples.     

Development of a certified reference material for the determination of perfluorooctanoic acid

A certified reference material (CRM) for the determination of perfluorooctanoic acid (PFOA) has been issued as NMIJ CRM 4056-a by the National Metrology Institute of Japan, National Institute of Advanced Industrial Science and Technology (NMIJ/AIST). Purity (kg kg^?1) based on a titration method was determined by subtracting the mass fractions of impurities measured using liquid chromatography/mass spectrometry (LC/MS) from those of acids expressed as PFOA measured by a neutralization potentiometric titration. To validate an obtained result, purity based on a mass balance method was determined by subtracting the mass fractions of impurities, measured using LC/MS, Karl-Fischer titration (KFT), and vacuum evaporation, from 1 kg kg^?1. Results from both titration and mass balance methods were in agreement within the accepted limits of uncertainty. The certified purity of NMIJ CRM 4056-a was determined to be 0.959 kg kg^?1, calculated as the mean of the results obtained with the two methods. The standard uncertainty of the certified purity was evaluated from purity evaluations as well as from sample homogeneity and stability obtained from LC/MS and KFT analyses. Consequently, the expanded uncertainty was estimated to be 0.005 kg kg^?1 with a coverage factor of k = 2.     

Conversion of arsenobetaine to dimethylarsinic acid by arsenobetaine-decomposing bacteria isolated from coastal sediment

Arsenobetain [(CH₃)₃As⁺CH₂COO^-]-containing growth media (1/5 ZoBell 2216E and solution of inorganic salts) were inoculated with two bacterial strains, which were isolated from a coastal sediment and identified as members of the Vibro-Aeromonas group, and incubated under aerobic and anaerobic conditions. Arsenobetaine was converted to a metabolite only under aerobic conditions. This arsenic metabolite was identified as dimethylarsinic acid [(CH₃)₂AsOOH] by hydride generation/cold trap/GC MS/SIM analysis and high-performance liquid-chromatographic behaviour. The conversion pattern shown by these arsenobetaine-decomposing bacteria (that is, arsenobetaine → dimethylarsinic acid) was fairly different from that shown by the addition of sediment itself as the source of arsenobetaine-decomposing micro-organisms (that is, arsenobetaine → trimethylarsine oxide → inorganic arsenic). This result suggests to us that various micro-organisms, including the arsenobetaine-decomposing bacteria isolated in this study, participate in the degradation of arsenobetaine in marine environments.     

Uptake and degradation of arsenobetaine by the microorganisms occurring in sediments

We have reported the degradation of arsenobetaine [(CH₃)₃As⁺CH₂COO^?] to inorganic arsenic by microorganisms from various marine origins such as sediments. However, there was no information as to the fate of the ingested arsenobetaine within the body of the microorganisms before excretion. In this study, arsenobetaine and sediments were added to two culture media (1/5 Zobell 2216E and a solution of inorganic salts) and aerobically incubated at 25°C in the dark. Despite the degradation and complete disappearance of arsenobetaine from the filtrates of the incubation mixtures, the major arsenic compound from the microorganisms harvested from the mixtures was identified by HPLC as arsenobetaine throughout the incubation period. The presence of arsenobetaine was further confirmed by TLC and fast atom bombardment mass spectrometry (FAB MS). A minor arsenical also present in the incubated microorganisms, dimethylarsinic acid, was detected.     

Certified reference material for quantification of polycyclic aromatic hydrocarbons in sediment from the National Metrology Institute of Japan

The National Metrology Institute of Japan has issued a certified reference material (CRM) of freshwater lake sediment for polycyclic aromatic hydrocarbon (PAHs) analyses. The certification used three extraction techniques: pressurized liquid extraction (PLE) with toluene, PLE with dichloromethane/ethyl acetate (1:1 by volume), and alkaline extraction (1 M KOH in methanol) in combination with microwave-assisted extraction. Both gas chromatography/mass spectrometry (GC/MS) and liquid chromatography/dopant-assisted atmospheric pressure photoionization/MS (LC/DA-APPI/MS) analyses were used. Certified values are provided for 18 PAHs at 1–25 μg kg⁻¹ except for perylene (2.08 × 10³ μg kg⁻¹), and information values are provided for two. Since the values of PAHs in the CRM are much lower than those in other CRMs and are comparable to those found at sites with little human influence, the CRM is suitable for PAH monitoring in sediment and soil samples.     

Mineral oil certified reference materials for the determination of polychlorinated biphenyls from the National Metrology Institute of Japan (NMIJ)

Four mineral oil certified reference materials (CRMs), NMIJ CRM 7902-a, CRM 7903-a, CRM 7904-a, and CRM 7905-a, have been issued by the National Metrology Institute of Japan, which is part of the National Institute of Advanced Industrial Science and Technology (NMIJ/AIST), for the determination of polychlorinated biphenyls (PCBs). The raw materials for the CRMs were an insulation oil (CRM 7902-a and CRM 7903-a) and a fuel oil (CRM7904-a and CRM 7905-a). A solution of PCB3, PCB8, and technical PCB products, comprising four types of Kaneclor, was added to the oil matrices. The total PCB concentrations in the PCB-fortified oils (CRM 7902-a and CRM 7904-a) are approximately 6 mg kg⁻¹. In addition, the mineral oils which were not fortified with PCBs were also distributed as CRMs (CRM 7903-a and CRM 7905-a). Characterization of these CRMs was conducted by the NMIJ/AIST, where the mineral oils and the PCB solution were analyzed using multiple analytical methods such as dimethylsulfoxide extraction, normal-phase liquid chromatography, gel permeation chromatography, reversed-phase liquid chromatography, and chromatography using sulfoxide-bonded silica; and/or various capillary columns for gas chromatography, and two ionization modes for mass spectrometry. The target compounds in the mineral oils and those in the PCB solution were determined by one of the primary methods of measurement, isotope dilution–mass spectrometry (ID-MS). Certified values have been provided for 11 PCB congeners (PCB3, 8, 28, 52, 101, 118, 138, 153, 180, 194, and 206) in the CRMs. These CRMs have information values for PCB homologue concentrations determined by using a Japanese official method for determination of PCBs in wastes and densities determined with an oscillational density meter. Because oil samples having arbitrary PCB concentrations between respective property values of the PCB-fortified and nonfortified CRMs can be prepared by gravimetric mixing of the CRM pairs, these CRMs can be used for validation of PCB analyses using various instruments which have different sensitivities. Figure Preparation and certification processes of the mineral oil CRMs (example shown is polychlorinated biphenyls in insulation oil, high/low concentrations) Electronic supplementary material  The online version of this article (doi:) contains supplementary material, which is available to authorized users.     

Measurement of progesterone in human serum by isotope dilution liquid chromatography–tandem mass spectrometry and comparison with the commercial chemiluminescence immunoassay

Progesterone is one of the steroid hormones. The hormone is especially important in preparing the uterus for the implantation of the blastocyst and in maintaining pregnancy. Its concentration in serum is measured to determine ovarian function and to predict early pregnancy. The progesterone concentration is also important for in-vitro fertilization and embryo-transfer outcomes. We have established isotope dilution liquid chromatography–tandem mass spectrometry as a primary method for the measurement of progesterone in human serum. Progesterone and its isotopic analogue, progesterone-¹³C₂, in serum were monitored at mass transitions of m/z 315.2/109.2 and 317.2/111.2 respectively in multiple-reaction monitoring (MRM) mode with electrospray positive ionization. For validation of the method, progesterone in a National Institute of Standards and Technology standard reference material (NIST SRM) was measured, and the measured results were in good agreement with the reference values within the uncertainty. On the basis of the established method, progesterone certified reference material (CRM) was developed in this work. The certified value was (1.41 ± 0.036) μg kg⁻¹. The repeatability of 1.1% and reproducibility of 0.14% showed that ID LC–MS–MS is a reliable and reproducible method. The expanded uncertainty for the measurement of progesterone in the CRM was approximately 2.6% within 95% confidence limits. The detection limit of progesterone was approximately 0.6 μg kg⁻¹. The progesterone CRMs were distributed to representative clinical laboratories in the Republic of Korea for comparison with the chemiluminescence immunoassay (CLIA), which is the most sensitive immunoassay method. The results from the comparison showed quite a large bias among the participating laboratories. This implies that the CRM is a very important material for establishment of traceability to its practical use.     

Certification of mono-, di-, and tributyltin compounds in marine sediment certified reference material by species-specific isotope dilution mass spectrometric analysis using synthesized <Superscript>118</Superscript>Sn-labeled butyltins

A new marine sediment reference material (NMIJ CRM 7301-a) for butyltins analysis was prepared and certified by the National Metrological Institute of Japan, National Institute of Advanced Industrial Science and Technology (NMIJ/AIST). The original material of the sediment was collected at a bay near industrial activities in Japan. The sediment material was air-dried, sieved, homogenized, and packaged into 1,000 glass bottles (60 g each). Certification of NMIJ CRM 7301-a was carried out at NMIJ using two different types of species-specific isotope dilution mass spectrometry: isotope dilution–ethylation–gas chromatography/inductively coupled plasma mass spectrometry (GC/ICPMS) and isotope dilution–ethylation–gas chromatography/mass spectrometry (GC/MS). A mixture of ¹¹⁸Sn-enriched monobutyltin, dibutyltin, and tributyltin was synthesized in our laboratory and was used as a spike for both techniques. Certified values are given for tributyltin (0.044±0.004 mg kg^–1 as Sn), dibutyltin (0.056±0.006 mg kg^–1 as Sn, and monobutyltin (0.058±0.013 mg kg^–1 as Sn), being at lower levels than currently available sediment CRMs for the analysis of organotins.