Thermophysical properties of the binary mixtures (1,8-cineole + 1-alkanol) at T = (298.15 and 313.15) K and at atmospheric pressure

This work presents the measurements of the density, speed of sound, refractive index and enthalpy of binary mixtures containing {1,8-cineole + 1-alkanol (ethanol, 1-propanol, 1-butanol, and 1-pentanol)} at two temperatures (298.15 and 313.15) K and atmospheric pressure. The determination of excess molar volume, speed of sound deviation, refractive index deviation, molar refraction, molar refraction deviation, excess isentropic compressibility, and excess molar enthalpy are also given. Redlich–Kister equation was used to fit these derivate properties. The experimental data of the constituent binaries were analysed to discuss the nature and strengths of intermolecular interactions. Eventually some models, SAFT and PC-SAFT for density, Free Length and Collision Factor for speed of sound, Gladstone-Dale Arago-Biot for refractive index, and UNIFAC for excess molar enthalpy, among others, were successfully applied.     

Thermophysical properties of {(±)-linalool + propan-1-ol}: A first stage towards the development of a green process

In this paper, densities, speeds of sound and refractive indexes of binary mixture of {(±)-linalool (1) + propan-1-ol (2)} at four temperatures (283.15, 298.15, 313.15, and 328.15) K and 0.1 MPa are reported over the whole composition range. These data were used to calculate excess molar volume, speed of sound deviation, excess isentropic compressibility, refractive index deviation, molar refraction, and molar refraction deviation at the four work temperatures. All magnitudes were fitted to the Redlich–Kister equation. Subsequently prediction of speed of sound and refractive index was carried out using several theoretical models or equations. On the other hand, the density of the same mixture was determined in the same temperature range at pressures from 20 MPa to 40 MPa. Four equation of state (Peng–Robinson, Patel–Teja, SAFT, PC-SAFT) were tested as predictive models of the PρT behavior. The best results were obtained by PC-SAFT, with an average absolute deviation of 0.83%.     

Volumetric properties of (piperidine + water) binary system: Measurements and modeling

Densities of pure piperidine (CAS No.: 110-89-4) and of its mixtures with water have been measured over the whole range of compositions at temperatures from 283.15 K to 347.15 K using Anton Paar? digital vibrating tube densimeter. The density of this system has been found increasing with mass fraction of water. Excess molar volumes have been calculated using the measured experimental densities and correlated using the Redlich–Kister equation. Redlich–Kister equation parameters have been adjusted on experimental data. In addition, partial molar volumes and partial excess molar volumes at infinite dilution have been calculated for each component.     

Density,speed of sound,and refractive index measurements for the binary systems (butanoic acid + propanoic acid,or 2-methyl-propanoic acid) at T = (293.15 to 313.15) K

Density, speed of sound, and refractive index for the binary systems (butanoic acid + propanoic acid, or 2-methyl-propanoic acid) were measured over the whole composition range and at T = (293.15, 298.15, 303.15, 308.15, and 313.15) K. The excess molar volumes, isentropic compressibilities, excess isentropic compressibilities, molar refractions, and deviation in refractive indices were also calculated by using the experimental densities, speed of sound, and refractive indices data, respectively. The Redlich–Kister smoothing polynomial equation was used to fit the excess molar volume, excess isentropic compressibility and deviation in refractive index data. The thermodynamic properties have been discussed in terms of intermolecular interactions between the components of the mixtures.     

Application of the PFV EoS correlation to excess molar volumes of (1-ethyl-3-methylimidazolium ethylsulfate + alkanols) at different temperatures

The experimental densities for the binary systems of an ionic liquid and an alkanol {1-ethyl-3-methylimidazolium ethylsulfate [EMIM]⁺ [EtSO₄]^? + methanol or 1-propanol or 2-propanol} were determined at T = (298.15, 303.15, and 313.15) K. The excess molar volumes for the above systems were then calculated from the experimental density values for each temperature. The Redlich–Kister smoothing polynomial was used to fit the experimental results and the partial molar volumes were determined from the Redlich–Kister coefficients. For all the systems studied, the excess molar volume results were negative over the entire composition range for all the temperatures. The excess molar volumes were correlated with the pentic four parameter virial (PFV) equation of state (EoS) model.     

Excess molar volumes and isentropic compressibility of binary systems {trioctylmethylammonium bis(trifluoromethysulfonyl)imide + methanol or ethanol or 1-propanol} at different temperatures

This paper reports measurements of densities for the binary systems of an ionic liquid and an alkanol at T = (298.15, 303.15, and 313.15) K. The IL is trioctylmethylammonium bis(trifluoromethylsulfonyl)imide [OMA]⁺[Tf₂N]^? and the alkanols are methanol, or ethanol, or 1-propanol. The speed of sound at T = 298.15 K for the same binary systems was also measured. The excess molar volumes and the isentropic compressibilities for the above systems were then calculated from the experimental densities and the speed of sound, respectively. Redlich–Kister smoothing polynomial equation was used to fit the excess molar volume and the deviation in isentropic compressibility data. The partial molar volumes were determined from the Redlich–Kister coefficients. For all the systems studied, the excess molar volumes have both negative and positive values, while the deviations in isentropic compressibility are negative over the entire composition range.     

Excess molar volumes and partial molar volumes for (propionitrile + an alkanol) at T = 298.15 K and p = 0.1 MPa

The excess molar volumes and the partial molar volumes for (propionitrile + an alkanol) at T = 298.15 K and at atmospheric pressure are reported. The hydrogen bonding between the OH⋯NC groups are discussed in terms of the chain length of the alkanol. The alkanols studied are (methanol, ethanol, 1-propanol, 2-propanol, 1-butanol, and 1-pentanol).The excess molar volume data was fitted to the Redlich–Kister equation The partial molar volumes were calculated from the Redlich–Kister coefficients.     

Volumetric properties of ternary (IL + 2-propanol or 1-butanol or 2-butanol + ethyl acetate) systems and binary (IL + 2-propanol or 1-butanol or 2-butanol) and (1-butanol or 2-butanol + ethyl acetate) systems

The experimental densities for the binary or ternary systems were determined at T = (298.15, 303.15, and 313.15) K. The ionic liquid methyl trioctylammonium bis(trifluoromethylsulfonyl)imide ([MOA]⁺[Tf₂N]⁻) was used for three of the five binary systems studied. The binary systems were ([MOA]⁺[Tf₂N]⁻ + 2-propanol or 1-butanol or 2-butanol) and (1-butanol or 2-butanol + ethyl acetate). The ternary systems were {methyl trioctylammonium bis(trifluoromethylsulfonyl)imide + 2-propanol or 1-butanol or 2-butanol + ethyl acetate}. The binary and ternary excess molar volumes for the above systems were calculated from the experimental density values for each temperature. The Redlich–Kister smoothing polynomial was fitted to the binary excess molar volume data. Virial-Based Mixing Rules were used to correlate the binary excess molar volume data. The binary excess molar volume results showed both negative and positive values over the entire composition range for all the temperatures.The ternary excess molar volume data were successfully correlated with the Cibulka equation using the Redlich–Kister binary parameters.     

Excess molar volume,viscosity, and refractive index study for the ternary mixture {2-methyl-2-butanol (1) + tetrahydrofuran (2) + propylamine (3)} at different temperatures. Application of the ERAS-model and Peng–Robinson–Stryjek–Vera equation of state

Densities, viscosities, and refractive indices of the ternary mixture consist of {2-methyl-2-butanol (1) + tetrahydrofuran (THF) (2) + propylamine (3)} at a temperature of 298.15 K and related binary mixtures were measured at temperatures of (288.15, 298.15, and 308.15) K at ambient pressure. Data were used to calculate the excess molar volumes and the deviations of the viscosity and refractive index. The Redlich–Kister and the Cibulka equations were used for correlating binary and ternary properties, respectively. The ERAS-model has been applied for describing the binary and ternary excess molar volumes and also Peng–Robinson–Stryjek–Vera (PRSV) equation of state (EOS) has been used to predict the binary and ternary excess molar volumes and viscosities.     

How reliable are extrapolations to infinite dilution of partial molar properties using Redlich–Kister fittings?

An explicit method for uncertainty estimation associated with excess partial molar properties at infinite dilution calculated using standard uncertainties of Redlich–Kister parameters, fitted to data over the whole composition range, is presented for the first time. The application of this method to sets of accurate volumetric experimental data for aqueous water + ethanol binary mixtures, experimentally determined by different authors is made and the results are compared. A refinement of this method is also presented when, in very-diluted regions, Redlich–Kister lines deviate from experimental points more than their standard uncertainties. The procedure of uncertainty calculation is based on the Guide to the Expression of Uncertainty in Measurements (GUM).     

Densities and volume properties of (water + tert-butanol) over the temperature range of (274.15 to 348.15) K at pressure of 0.1 MPa

The densities of {water (1) + tert-butanol (2)} binary mixture were measured over the temperature range (274.15 to 348.15) K at atmospheric pressure using “Anton Paar” digital vibrating-tube densimeter. Density measurements were carried out over the whole concentration range at (308.15 to 348.15) K. The following volume parameters were calculated: excess molar volumes and thermal isobaric expansivities of the mixture, partial molar volumes and partial molar thermal isobaric expansivities of the components. Concentration dependences of excess molar volumes were fitted with Redlich–Kister equation. The results of partial molar volume calculations using four equations were compared. It was established that for low alcohol concentrations at T ? 208 K the inflection points at x₂ ≈ 0.02 were observed at concentration dependences of specific volume. The concentration dependences of partial molar volumes of both water and tert-butanol had extremes at low alcohol content. The temperature dependence of partial molar volumes of water had some inversion at х₂ ≈ 0.65. The temperature dependence of partial molar volumes of tert-butanol at infinite dilution had minimum at ≈288 K. It was discovered that concentration dependences of thermal isobaric expansivities of the mixture at small alcohol content and low temperatures passed through minimum.     

Densities and volumetric properties of (N-(2-hydroxyethyl)morpholine + ethanol, + 1-propanol, + 2-propanol, + 1-butanol,and + 2-butanol) at (293.15, 298.15, 303.15, 313.15, and 323.15) K

Densities of binary mixtures of N-(2-hydroxyethyl)morpholine with ethanol, 1-propanol, 2-propanol, 1-butanol, and 2-butanol were measured over the entire composition range at temperatures from (293.15 to 323.15) K and atmospheric pressure using a vibrating-tube densimeter. The excess molar volumes, V^E were calculated from density data and fitted to the Redlich–Kister polynomial equation. Apparent molar volumes, partial molar volume at infinite dilution and the thermal expansion coefficient of the mixtures were also calculated. The V^E values were found to be negative over the entire composition range and at all temperatures studied and become less negative with increasing carbon chain length of the alkanols.     

Excess molar volumes and deviation in viscosities of binary liquid mixtures of acrylic esters with hexane-1-ol at 303.15 and 313.15 K

Densities and viscosities for the four binary liquid mixtures of methyl acrylate, ethyl acrylate, butyl acrylate and methyl methacrylate with hexane-1-ol at temperatures 303.15 and 313.15 K and at atmospheric pressure were measured over the entire composition range. These values were used to calculate excess molar volumes and deviation in viscosities which were fitted to Redlich–Kister polynomial equation. Recently proposed Jouyban Acree model was also used to correlate the experimental values of density and viscosity. The mixture viscosities were correlated by several semi-empirical approaches like Hind, Choudhary–Katti, Grunberg–Nissan, Tamura and Kurata, McAllister three and four body model equations. A graphical representation of excess molar volumes and deviation in isentropic compressibility shows positive nature whereas deviation in viscosity shows negative nature at both temperatures for all four binary liquid mixtures. Positive values of excess molar volumes show that volume expansion is taking place causing rupture of H-bonds in self associated alcohols. The results were discussed in terms of molecular interactions prevailing in the mixtures.     

Volumetric behaviour of the (2,2,4-trimethylpentane + methylbenzene + butan-1-ol) ternary system and its binary sub-systems within the temperature range (298.15–328.15) K

Densities and speeds of sound of the (2,2,4-trimethylpentane + methylbenzene + butan-1-ol) ternary system as well as all its binary sub-systems were measured at four temperatures, namely 298.15 K, 308.15 K, 318.15 K, and 328.15 K at atmospheric pressure by a vibrating-tube densimeter DSA 5000. The binary (isooctane + toluene) system was studied previously. Excess quantities (molar volume, adiabatic compressibility, and isobaric thermal expansivity) of the mixtures studied were calculated from the experimental densities and speed of sounds. The excess molar volume data were correlated using the Redlich–Kister equation. Both the positive and S-shaped excess molar volume curves were found for the systems studied. The excess molar volumes versus concentration of binary systems differed in the shape and temperature dependence. The experimental binary data were compared with literature data. The experimental excess molar volumes were analyzed by means of the Extended Real Associated Solution (ERAS) model. The experimental data and the ERAS model can help to estimate real behaviour of the systems studied.     

Volumetric and surface properties of pure ionic liquid n-octyl-pyridinium nitrate and its binary mixture with alcohol

The density and surface tension for pure ionic liquid N-octyl-pyridinium nitrate were measured from (293.15 to 328.15) K. The coefficient of thermal expansion, molecular volume, standard entropies, and lattice energy were calculated from the experimental density values. The critical temperature, surface entropy, surface enthalpy, and enthalpy of vaporization were also studied from the experimental surface tension results. Density and surface tension were also determined for binary mixtures of (N-octyl-pyridinium nitrate + alcohol) (methanol, ethanol, and 1-butanol) systems over the whole composition range at 298.15 K and atmospheric pressure. Excess molar volumes and surface tension deviations for the binary systems have been calculated and were fitted to a Redlich–Kister equation to determine the fitting parameters and the root mean square deviations. The partial molar volume, excess partial molar volume, and apparent molar volume of the component IL and alcohol in the binary mixtures were also discussed.     

Densities and dynamic viscosities of the binary system (water + 1-hexyl-3-methylimidazolium bromide) at different temperatures

Densities and viscosities were measured for pure ionic liquid [C₆mim][Br] (1-hexyl-3-methylimidazolium bromide) and the binary system (water + [C₆mim][Br]) at 0.1 MPa and in the (293.15 to 333.15) K range. The excess molar volume and viscosity deviation were calculated and correlated by Redlich–Kister polynomial expansions. The fitting parameters and the standard deviations were determined.     

Density,viscosity, isothermal (vapour + liquid) equilibrium,excess molar volume,viscosity deviation,and their correlations for chloroform + methyl isobutyl ketone binary system

Density and viscosity measurements for pure chloroform and methyl isobutyl ketone at T = (283.15, 293.15, 303.15, and 313.15) K as well as for the binary system {x₁ chloroform + (1 − x₁) methyl isobutyl ketone} at the same temperatures were made over the whole concentration range. The experimental results were fitted to empirical equations, which permit the calculation of these properties over the whole concentration and temperature ranges studied. Data of the binary mixture were further used to calculate the excess molar volume and viscosity deviation. The (vapour + liquid) equilibrium (VLE) at T = 303.15 K for this binary system was also measured in order to calculate the activity coefficients and the excess molar Gibbs energy. This binary system shows no azeotrope and negative deviations from ideal behaviour. The excess or deviation properties were fitted to the Redlich–Kister polynomial relation to obtain their coefficients and standard deviations.     

Experimental densities,refractive indices,and speeds of sound of 12 binary mixtures containing alkanes and aromatic compounds at T = 313.15 K

Densities, speeds of sound, and refractive indices of 12 binary systems of alkanes (hexane, heptane, octane, and nonane) with aromatics (benzene, or toluene, or ethylbenzene) at T = 313.15 K and at atmospheric pressure were determined over the whole composition range, and are presented in this paper. From the experimental results, the derived and excess properties (isentropic compressibility, excess molar volumes, and excess molar isentropic compressibility) at T = 313.15 K were calculated and satisfactorily fitted to the Redlich–Kister equation.     

Ultrasound speeds and molar isentropic compressions of (3-ethoxypropane-1-amine + water) mixtures from T = (283.15 to 303.15) K

Alkoxyamines containing two hydrophilic groups with great affinity to water are multipurpose compounds with important applications, either on theoretical or practical grounds. The thermodynamic characterization of aqueous mixtures of these compounds is scant. Ultrasound speed measurements have been made in 53 mixtures of the aqueous ethoxypropane-1-amine binary system, across the entire composition range and temperatures between T = (283.15 and 303.15) K, at atmospheric pressure. By combining ultrasound speed and density data, values of the isentropic compressibility were derived. Excess molar isentropic compressions were estimated and analytically fitted to Redlich–Kister polynomial equations. Excess partial molar quantities were then calculated including their limiting values, which were obtained from the Redlich–Kister fitting coefficients. The temperature dependences of limiting partial molar isentropic compressions and isobaric expansions were also scrutinized. Compressibility changes associated with different patterns of aggregation and hydration over the whole composition range are identified.     

Density,excess properties,electrical conductivity and viscosity of 1-butyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide + γ-butyrolactone binary mixtures

Density, electrical conductivity and viscosity of binary liquid mixtures of 1-butyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide, [bmim][NTf₂], with γ-butyrolactone (GBL) were measured at temperatures from (293.15 to 323.15) K and at atmospheric pressure over the whole composition range. Excess molar volumes have been calculated from the experimental densities and were fitted with Redlich–Kister polynomial equation. Other volumetric properties, such as isobaric thermal expansion coefficients, partial molar volumes, apparent molar volumes and partial molar volumes at infinite dilution have been also calculated, in order to obtain information about interactions between GBL and selected ionic liquid.