Inhibition effect of 1-ethyl-3-methylimidazolium chloride on methane hydrate equilibrium

The dissociation conditions of methane hydrate in the presence of 0.1, 0.2, 0.3 and 0.4 mass fraction of 1-ethyl-3-methylimidazolium chloride (abbreviated by EMIM-Cl hereafter) were experimentally determined. A high pressure micro-differential scanning calorimeter equipped with a motorized pump was applied to measure the dissociation temperature of the (hydrate + liquid water + vapor) three-phase equilibrium under a constant pressure process with a pressure ranging from (5.0 to 35.0) MPa. The addition of EMIM-Cl would inhibit the methane hydrate formation. The most significant inhibition effect was observed at 0.4 mass fraction of EMIM-Cl in aqueous solution to lower the dissociation temperature by 12.82 K at 20.00 MPa in comparison to that of the (methane + water) system. The Peng–Robinson–Stryjek–Vera equation of state incorporated with COSMO-SAC activity coefficient model and the first order modified Huron–Vidal mixing rule were applied to evaluate the fugacity of vapor and liquid phase. A modified van der Waals and Platteeuw model with an explicit pressure dependence of the Langmuir adsorption constant was applied to determine the fugacity of hydrate phase. The predictive thermodynamic model successfully describes the tendency of phase behavior of methane hydrate in the presence of EMIM-Cl in the range from 0.1 to 0.4 mass fraction with absolute average relative deviation in predicted temperature of 0.70%.     

Experimental investigation on the dissociation conditions of methane hydrate in the presence of imidazolium-based ionic liquids

In this work, the performance of nine ionic liquids (ILs) as thermodynamic hydrate inhibitors is investigated. The dissociation temperature is determined for methane gas hydrates using a high pressure micro deferential scanning calorimeter between (3.6 and 11.2) MPa. All the aqueous IL solutions are studied at a mass fraction of 0.10. The performance of the two best ILs is further investigated at various concentrations. Electrical conductivity and pH of these aqueous IL solutions (0.10 mass fraction) are also measured. The enthalpy of gas hydrate dissociation is calculated by the Clausius–Clapeyron equation. It is found that the ILs shift the methane hydrate (liquid + vapour) equilibrium curve (HLVE) to lower temperature and higher pressure. Our results indicate 1-(2-hydroxyethyl) 3-methylimidazolium chloride is the best among the ILs studied as a thermodynamic hydrate inhibitor. A statistical analysis reveals there is a moderate correlation between electrical conductivity and the efficiency of the IL as a gas hydrate inhibitor. The average enthalpies of methane hydrate dissociation in the presence of these ILs are found to be in the range of (57.0 to 59.1) kJ ⋅ mol⁻¹. There is no significant difference between the dissociation enthalpy of methane hydrate either in the presence or in absence of ILs.     

Method for predicting the dissociation condition of a simple hydrate phase on an H–Lw–V line in isochoric operation

A method for predicting the location of a dissociation condition on an H–L_w–V line under isochoric operation was presented. To establish the method, the governing equations for the H–L_w–V coexistence under isochoric conditions were derived. Here, a liquid and a vapor phase were expressed by the PR EOS + MHV2 model and a hydrate phase by the van der Waals–Platteeuw model. The molar volume of the vapor phase was calculated from the equation of state, and a simple expression for the molar volume of the hydrate phase was derived. Then, to prove the validity of the proposed method, experimental studies about the dissociation process of the hydrates were performed. The temperature and pressure traces in the hydrate dissociation process, including the location of the dissociation condition, were successfully predicted by the proposed method. In addition, the thermodynamic consistency among the phase models was discussed. It was pointed out that agreement between the calculated and experimental results about the H–L_w–V equilibrium line did not ensure thermodynamic consistency among the phase models.     

Phase equilibria for H2 + CO2 + H2O system containing gas hydrates

Isothermal phase equilibrium (pressure–composition in the gas phase) for the ternary system of H₂ + CO₂ + H₂O has been investigated in the presence of gas hydrate phase. Three-phase equilibrium pressure increases with the H₂ composition of gas phase. The Raman spectra suggest that H₂ is not enclathrated in the hydrate-cages and behaves only like the diluent gas toward the formation of CO₂ hydrate. This fact is also supported by the thermodynamic analysis using Soave–Redlich–Kwong equation of state.     

Phase equilibrium measurements for semi-clathrate hydrates of the (CO2 + N2 + tetra-n-butylammonium bromide) aqueous solution system

The application of semi-clathrate hydrate formation technology for gas separation purposes has gained much attention in recent years. Consequently, there is a demand for experimental data for relevant semi-clathrate hydrate phase equilibria. In this work, semi-clathrate hydrate dissociation conditions for the system comprising mixtures of {CO₂ (0.151/0.399 mole fraction) + N₂ (0.849/0.601 mole fraction) + 0.05, 0.15, and 0.30 mass fraction tetra-n-butylammonium bromide (TBAB)} aqueous solutions have been measured and are reported. An experimental apparatus which was designed and built in-house was used for the measurements using the isochoric pressure-search method. The range of conditions for the measurements was from 277.1 K to 293.2 K for temperature and pressures up to 16.21 MPa. The phase equilibrium data measured demonstrate the high hydrate promotion effects of TBAB aqueous solutions.     

The partition coefficients of ethylene between vapor and hydrate phase for methane + ethylene + THF + water systems

The vapor-hydrate equilibria were studied experimentally in detail for CH₄ + C₂H₄ + tetrahydrofuran (THF) + water systems in the temperature range of 273.15–282.15 K, pressure range of 2.0–4.5 MPa, the initial gas–liquid volume ratio range of 45–170 standard volumes of gas per volume of liquid and THF concentration range of 4–12 mol%. The results demonstrated that, because of the presence of THF, ethylene was remarkably enriched in vapor phase instead of being enriched in hydrate phase for CH₄ + C₂H₄ + water system. This conclusion is of industrial significance; it implies that it is feasible to enrich ethylene from gas mixture, e.g., various kinds of refinery gases or cracking gases in ethylene plant, by forming hydrate.     

Experimental observations on the competing effect of tetrahydrofuran and an electrolyte and the strength of hydrate inhibition among metal halides in mixed CO2 hydrate equilibria

In the present work, experimental data on the equilibrium conditions of mixed CO₂ and THF hydrates in aqueous electrolyte solutions are reported. Seven different electrolytes (metal halides) were used in this work namely sodium chloride (NaCl), calcium chloride (CaCl₂), magnesium chloride (MgCl₂), potassium bromide (KBr), sodium fluoride (NaF), potassium chloride (KCl), and sodium bromide (NaBr). All equilibrium data were measured by using Cailletet apparatus. Throughout this work, the overall concentration of CO₂ and THF were kept constant at (0.04 and 0.05) mol fraction, respectively, while the concentration of electrolytes were varied. The experimental temperature ranged from (275 to 305) K and pressure up 7.10 MPa had been applied. From the experimental results, it is concluded that THF, which is soluble in water is able to suppress the salt inhibiting effect in the range studied. In all quaternary systems studied, a four-phase hydrate equilibrium line was observed where hydrate (H), liquid water (L_W), liquid organic (L_V), and vapour (V) exist simultaneously at specific pressure and temperature. The formation of this four-phase equilibrium line is mainly due to a liquid–liquid phase split of (water + THF) mixture when pressurized with CO₂ and the split is enhanced by the salting-out effect of the electrolytes in the quaternary system. The strength of hydrate inhibition effect among the electrolytes was compared. The results shows the hydrate inhibiting effect of the metal halides is increasing in the order NaF < KBr < NaCl < NaBr < CaCl₂ < MgCl₂. Among the cations studied, the strength of hydrate inhibition increases in the following order: K⁺ < Na⁺ < Ca²⁺ < Mg²⁺. Meanwhile, the strength of hydrate inhibition among the halogen anion studied decreases in the following order: Br^? > Cl^? > F^?. Based on the results, it is suggested that the probability of formation and the strength of ionic–hydrogen bond between an ion and water molecule and the effects of this bond on the ambient water network are the major factors that contribute to hydrate inhibition by electrolytes.     

Phase equilibria in ternary (carbon dioxide + tetrahydrofuran + water) system in hydrate-forming region: Effects of carbon dioxide concentration and the occurrence of pseudo-retrograde hydrate phenomenon

In the present work, the three- and four-phase hydrate equilibria of (carbon dioxide (CO₂) + tetrahydrofuran (THF) + water) system are measured by using Cailletet equipment in the temperature and pressure range of (272 to 292) K and (1.0 to 7.5) MPa, respectively, at different CO₂ concentration. Throughout the study, the concentration of THF is kept constant at 5 mol% in the aqueous solution. In addition, the fluid phase transitions of L_W–L_V–V → L_W–L_V (bubble point) and L_W–L_V–V → L_W–V (dew point) are determined when they are present in the ternary system. For comparison, the three-phase hydrate equilibria of binary (CO₂ + H₂O) are also measured. Experimental measurements show that the addition of THF as a hydrate promoter extends hydrate stability region by elevating the hydrate equilibrium temperature at a specified pressure. The three-phase equilibrium line H–L_W–V is found to be independent of the overall concentration of CO₂. Contradictory, at higher pressure, the phase equilibria of the systems are significantly influenced by the overall concentration of CO₂ in the systems. A liquid–liquid phase split is observed at overall concentration of CO₂ as low as 3 mol% at elevated pressure. The region is bounded by the bubble-points line (L_W–L_V–V → L_W–L_V), dew points line (L_W–L_V–V → L_W + V) and the four-phase equilibrium line (H + L_W + L_V + V). At higher overall concentration of CO₂ in the ternary system, experimental measurements show that pseudo-retrograde behaviour exists at pressure between (2.5 and 5) MPa at temperature of 290.8 K.     

Evidence of an odd–even effect on the thermodynamic parameters of odd fluorotelomer alcohols

A phase transition study, including vapour pressure determinations of odd fluorotelomer alcohols {oFTOH; CF₃(CF₂)_nCH₂OH, with n = 5 to 9}, is reported in order to explore the effect of the successive introduction of –CF₂– groups into the molecule on the thermodynamic properties related to (solid + liquid, solid + gas, and liquid + gas) equilibria. An odd–even effect on the thermodynamic parameters of fusion and sublimation was observed in the homologous series of odd fluorotelomer alcohols indicating an increase of the stability in the crystal packing for the members with an odd number of carbon atoms. The vaporization parameters of o-FTOH were compared with the literature data for their alkane analogues and the results showed a higher volatility of liquid fluorotelomer alcohols than their congeners. The higher molecular conformation restriction of perfluorinated alcohols and/or the higher molar mass seems to contribute to their higher entropy of vaporization which drives the volatility of the 1H,1H-perfluorinated alcohols.     

Thermodynamic stability of structure-H hydrates of methylcyclopentane and cyclooctane helped by methane

The four-phase equilibria were measured for the methylcyclopentane+methane+H₂O hydrate system (274.28–287.40 K, 1.75–9.34 MPa) and the cyclooctane+methane+H₂O hydrate system (274.08–288.57 K, 1.60–9.33 MPa). Each structure-H hydrate has the lower equilibrium pressure than the pure methane structure-I hydrate in the temperature range of the present work. The isothermal equilibrium pressures of both methylcyclopentane and cyclooctane hydrates are slightly higher than that of methylcyclohexane hydrate.     

Enthalpies of dissociation of clathrate hydrates of carbon dioxide,nitrogen, (carbon dioxide + nitrogen), and (carbon dioxide + nitrogen + tetrahydrofuran)

A calorimetric technique is described for measuring the enthalpy of dissociation liberated from solid hydrates. In this study, the enthalpies of dissociation were determined at T =  273.65 K andp =  0.1 MPa for simple and mixed hydrates of carbon dioxide, nitrogen, (carbon dioxide  +  nitrogen), and (carbon dioxide  +  nitrogen  +  tetrahydrofuran) using an isothermal microcalorimeter. The addition of tetrahydrofuran (THF) promoted hydrate stability and increased the number of guest molecules encaged in the small and large cavities of the hydrate lattice, resulting in lower enthalpy of dissociation, compared with structure II hydrate. The composition ratio of guest molecules did not affect the enthalpy of dissociation, which was found to be nearly constant for the same mixture.     

Dissociation behaviour of (tetra-n-butylammonium bromide + tetra-n-butylammonium chloride) mixed semiclathrate hydrate systems

The thermal properties of {tetra-n-butylammonium bromide + tetra-n-butylammonium chloride (TBAB + TBAC)} mixed semiclathrate hydrates prepared from aqueous solutions were investigated by dissociation temperature measurements and differential scanning calorimetry (DSC). The maximum dissociation temperature of the mixed hydrate crystals at 0.1 MPa is 288.5 K for x_TBAB = 0.2 {mole fraction of TBAB to (TBAB + TBAC)}, which is higher than that of the pure hydrates {T = (285.5 and 288.2) K for TBAB and TBAC hydrates, respectively}. In addition, the dissociation enthalpies of the mixed hydrates are higher than those of the pure hydrates {(5.55 ± 0.06) kJ ⋅ mol⁻¹ H₂O for pure TBAB hydrate and (5.30 ± 0.05) kJ ⋅ mol⁻¹ H₂O for pure TBAC hydrate}, with a maximum of (5.95 ± 0.12) kJ ⋅ mol⁻¹ H₂O recorded at approximately x_TBAB = 0.4. It was therefore suggested that the crystal distortion in (TBAB + TBAC) mixed hydrates, caused by replacing water molecules by both bromide and chloride anions, was smaller than that observed for each pure hydrate. Consequently, the hydration numbers in the mixed hydrates were hypothesized to be slightly higher than those of the pure hydrates.     

Hydrate phase equilibrium for the (hydrogen + tert-butylamine + water) system

The three-phase equilibrium conditions of ternary (hydrogen + tert-butylamine + water) system were first measured under high-pressure in a “full view” sapphire cell. The tert-butylamine–hydrogen binary hydrate phase transition points were obtained through determining the points of intersection of three phases (H–L_w–V) to two phases (L_w–V) experimentally. Measurements were made using an isochoric method. Firstly, (tetrahydrofuran + hydrogen) binary hydrate phase equilibrium data were determined with this method and compared with the corresponding experimental data reported in the literatures and the acceptable agreements demonstrated the reliability of the experimental method used in this work. The experimental investigation on (tert-butylamine + hydrogen) binary hydrate phase equilibrium was then carried out within the temperature range of (268.4 to 274.7) K and in the pressure range of (9.54 to 29.95) MPa at (0.0556, 0.0886, 0.0975, and 0.13) mole fraction of tert-butylamine. The three-phase equilibrium curve (H + L_w + V) was found to be dependent on the concentration of tert-butylamine solution. Dissociation experimental results showed that tert-butylamine as a hydrate former shifted hydrate stability region to lower pressure and higher temperature.     

S6 Isomer of C60(CF3)12: Synthesis,properties and thermodynamic functions

A crystalline form of S₆-С₆₀(CF₃)₁₂ was synthesized in an amount sufficient for reliable experimental investigation. We determined the enthalpy of combustion of S₆-С₆₀(CF₃)₁₂ in oxygen and its heat capacity, which made possible to derive the thermodynamic functions of S₆-С₆₀(CF₃)₁₂, namely the enthalpy of formation, the entropy and the Gibbs energy at T = 298.15 K. These experimental thermochemical data enabled estimation of the formation energy for a broad range of other trifluoromethylated compounds C₆₀(CF₃)_n, with n = (2–18; 24), on the basis of their DFT calculated relative energies.     

On the kinetics of thermal electron attachment to perfluoroethers

In this Letter we report the results of the measurements of the rate coefficients for thermal attachment to several perfluoroethers namely perfluorodiglyme (C₆F₁₄O₃), perfluorotriglyme (C₈F₁₈O₄), perfluoropolyether (CF₃–(OCF(CF₃)CF₂)_n–(OCF₂)_m–OCF₃) and perfluorocrownether ((C₂F₄O)₅). Rate coefficients were obtained under thermal conditions in the temperature range 298–378 K. The increase of the rates with temperature follows the Arrhenius law and the activation energies have been obtained from the slope of the ln(k) vs. 1/T. The respective values of the rate coefficients (at 298 K) and activation energies are as follows: 7.7 ± 1.2 × 10^?11 cm³ s^?1 (0.18 ± 0.005 eV), 6.7 ± 2.1 × 10^?11 cm³ s^?1 (0.25 ± 0.004 eV), 2.1 ± 0.2 × 10^?10 cm³ s^?1 (0.16 ± 0.010 eV), 3.1 × 10^?11 cm³ s^?1 (0.27 ± 0.003 eV) for C₆F₁₄O₃, C₈F₁₈O₄, CF₃–(OCF(CF₃)CF₂)_n–(OCF₂)_m–OCF₃ and (C₂F₄O)₅.     

Phase equilibrium measurements for clathrate hydrates of flue gas (CO2 + N2 + O2) in the presence of tetra-n-butyl ammonium bromide or tri-n-butylphosphine oxide

This paper reports the measured hydrate phase equilibria of simulated flue gas (12.6 vol% CO₂, 80.5 vol% N₂, 6.9 vol% O₂) in the presence of tetra-n-butyl ammonium bromide (TBAB) or tri-n-butylphosphine oxide (TBPO), at (0, 5 and 26) wt%, respectively. The measurements of the phase boundary between (hydrate + liquid + vapor) (H + L + V) phases and (liquid + vapor) (L + V) phases were performed within the temperature range (275.97 to 293.99) K and pressure range (1.56 to 18.78) MPa with using the isochoric step-heating pressure search method. It was found that addition of TBAB or TBPO allowed the incipient equilibrium hydrate formation conditions for the flue gas to become milder. Compared to TBAB, TBPO was largely more effective in reducing the phase equilibrium pressure.     

The influence of chloride on the initial anodic dissolution of Cu3Au(1 1 1)

We report a detailed in situ X-ray diffraction study of the influence of chloride on the atomic structure evolution at the solid-electrolyte interface during the selective dissolution of Cu from a Cu₃Au(1 1 1) surface immersed in 0.1 M H₂SO₄. We disclose that the formation of the initial ultrathin Au-rich (1 1 1) with an inverted stacking sequence, as recently observed at Cu₃Au(1 1 1) in contact with pure 0.1 M H₂SO₄, is strongly influenced by adding 5 mM HCl. The main finding is a negative shift of about 150 mV of the critical potential at which the ultra-thin Au-rich layer transforms into thicker Au islands. The presented results support the view that it is not a thermodynamic driving force, but rather the rate of surface diffusion that dominates the formation of the structures of the metallic layer.     

Hydrate phase equilibrium and structure for (methane + ethane + tetrahydrofuran + water) system

The separation of methane and ethane through forming hydrate is a possible choice in natural gas, oil processing, or ethylene producing. The hydrate formation conditions of five groups of (methane + ethane) binary gas mixtures in the presence of 0.06 mole fraction tetrahydrofuran (THF) in water were obtained at temperatures ranging from (277.7 to 288.2) K. In most cases, the presence of THF in water can lower the hydrate formation pressure of (methane + ethane) remarkably. However, when the composition of ethane is as high as 0.832, it is more difficult to form hydrate than without THF system. Phase equilibrium model for hydrates containing THF was developed based on a two-step hydrate formation mechanism. The structure of hydrates formed from (methane + ethane + THF + water) system was also determined by Raman spectroscopy. When THF concentration in initial aqueous solution was only 0.06 mole fraction, the coexistence of structure I hydrate dominated by ethane and structure II hydrate dominated by THF in the hydrate sample was clearly demonstrated by Raman spectroscopic data. On the contrary, only structure II hydrate existed in the hydrate sample formed from (methane + ethane + THF + water) system when THF concentration in initial aqueous solution was increased to 0.10 mole fraction. It indicated that higher THF concentration inhibited the formation of structure I hydrate dominated by ethane and therefore lowered the trapping of ethane in hydrate. It implies a very promising method to increase the separation efficiency of methane and ethane.     

Thermodynamic study of (anthracene + phenanthrene) solid state mixtures

Polycyclic aromatic hydrocarbons (PAH) are common components of many materials, such as petroleum and various types of tars. They are generally present in mixtures, occurring both naturally and as byproducts of fuel processing operations. It is important to understand the thermodynamic properties of such mixtures in order to understand better and predict their behavior (i.e., fate and transport) in the environment and in industrial operations. To characterize better the thermodynamic behavior of PAH mixtures, the phase behavior of a binary (anthracene + phenanthrene) system was studied by differential scanning calorimetry, X-ray diffraction, and the Knudsen effusion technique. Mixtures of (anthracene + phenanthrene) exhibit non-ideal mixture behavior. They form a lower-melting, phenanthrene-rich phase with an initial melting temperature of 372 K (identical to the melting temperature of pure phenanthrene) and a vapor pressure of roughly lnP/Pa = −2.38. The phenanthrene-rich phase coexists with an anthracene-rich phase when the mole fraction of phenanthrene (x_P) in the mixture is less than or equal to 0.80. Mixtures initially at x_P = 0.90 consist entirely of the phenanthrene-rich phase and sublime at nearly constant vapor pressure and composition, consistent with azeotrope-like behavior. Quasi-azeotropy was also observed for very high-content anthracene mixtures (2.5 < x_P < 5) indicating that anthracene may accommodate very low levels of phenanthrene in its crystal structure.     

Hydrate phase equilibrium in the system of (carbon dioxide + 2,2-dimethylbutane + water) at temperatures below freezing point of water

The four-phase equilibrium conditions of (vapor + liquid + hydrate + ice) were measured in the system of (CO₂ + 2,2-dimethylbutane + water). The measurements were performed within the temperature range (254.2 to 270.2) K and pressure range (0.490 to 0.847) MPa using an isochoric method. Phase equilibrium conditions of hydrate formed in this study were measured to be at higher temperatures and lower pressures than those of structure I CO₂ simple hydrate. The largest difference in the equilibrium pressures of structure I CO₂ hydrate and the hydrate formed in the present study was 0.057 MPa at T = 258.3 K. On the basis of the four-phase equilibrium data obtained, the quintuple point for the (ice + structure I hydrate + structure H hydrate + liquid + vapor) was also determined to be T = 266.4 K and 0.864 MPa. The results indicate that structure H hydrate formed with CO₂ and 2,2-dimethylbutane is stable exclusively at the temperatures below the quintuple temperature.