High temperature normal phase liquid chromatography of aromatic hydrocarbons on bare zirconia

The normal phase HPLC behavior of a bare zirconia column was studied at temperatures up to 200 °C using a hexane mobile phase. The use of elevated column temperatures significantly decreased the retention of twenty five aromatic model compounds according to the van't Hoff equation (>30-fold decrease for some compounds). Large improvements in peak shape, efficiency (>2.2-fold), aromatic group-type selectivity, and column re-equilibration times (>5-fold) were obtained at elevated temperatures. The thermal decomposition of two polar nitrogen compounds (indole and carbazole) was observed in a hexane/dichloromethane mobile phase at temperatures greater than 100 °C. The first order decomposition of carbazole was studied in further detail.     

Application of sunflower stalk‐carbon nitride nanosheets as a green sorbent in the solid‐phase extraction of polycyclic aromatic hydrocarbons followed by high‐performance liquid chromatography

A green biocomposite of sunflower stalks and graphitic carbon nitride nanosheets has been applied as a solid‐phase extraction adsorbent for sample preparation of five polycyclic aromatic hydrocarbons in different solutions using high‐performance liquid chromatography with ultraviolet detection. Before the modification, sunflower stalks exhibited relatively low adsorption to the polycyclic aromatic hydrocarbons extraction. The modified sunflower stalks showed increased adsorption to the analytes extraction due to the increase in surface and existence of a π–π interaction between the analytes and graphitic carbon nitride nanosheets on the surface. Under the optimal conditions, the limits of detection and quantification for five polycyclic aromatic hydrocarbons compounds could reach 0.4–32 and 1.2–95 ng/L, respectively. The method accuracy was evaluated using recovery measurements in spiked real samples and good recoveries from 71 to 115% with relative standard deviations of <10% have been achieved. The developed method was successfully applied for polycyclic aromatic hydrocarbons determination in various samples—well water, tap water, soil, vegetable, and barbequed meat (kebab)—with analytes contents ranging from 0.065 to 13.3 μg/L. The prepared green composite as a new sorbent has some advantages including ease of preparation, low cost, and good reusability.     

Influence of silicon defects on the adsorption of thiophene-like compounds on polycyclic aromatic hydrocarbons: a theoretical study using thiophene + coronene as the simplest model

Physisorption and chemisorption processes of thiophene on coronene and 2Si-coronene have been studied using density functional theory and MP2 methods. These systems have been chosen as the simplest models to describe the adsorption of thiophene-like compounds on polycyclic aromatic hydrocarbons (PAHs). The calculated data suggest that the presence of silicon atoms in PAHs could favor their interaction with thiophene and similar compounds. Small stabilization energies have been found for several physisorbed complexes. The thiophene chemisorption on coronene seems very unlikely to occur, while that on 2Si-coronene leads to addition products which are very stable, with respect to the isolated reactants. These chemisorption processes were found to be exoergic (DeltaG < 0) in the gas phase and in the nonpolar liquid phase. The results reported in this work suggest that silicon defects on extended polycyclic aromatic hydrocarbons, such as graphite, soot, and large-diameter carbon nanotubes, could make them useful in the removal processes of aromatic sulfur compounds from oil hydrocarbons.     

System for calculating the linear temperature-programmed retention indices of polycyclic aromatic compounds

Theoretical procedures have been used to predict linear temperature-programmed retention indices for polycyclic aromatic compounds. It is possible to calculate such indices for polycyclic aromatic compounds in some practical situations in which the compounds cannot be eluted during a simple linear temperature program. The theory has been tested for a number of polycyclic aromatic hydrocarbon (PAHs) in single- and multi-plateau temperature-programmed gas chromatography with SE-52 as the stationary phase. This method will extend the applicability of linear retention indices for the identification of the isomers of polycyclic aromatic compounds.     

褐煤蜡树脂中多环芳烃组成的研究

采用气相色谱法对云南寻甸褐煤蜡树脂和吉林舒兰褐煤蜡树脂,进行了多环芳烃分布特征的研究,从树脂中鉴定出６８个化合物的同系物。两个树脂样均以菲系化合物占有优势,舒兰树脂中菲系列量约三倍于寻甸树脂的相应量     

A step toward direct fullerene synthesis: C60 fullerene precursors with fluorine in key positions

Several fluorine containing polycyclic aromatic hydrocarbons with exact carbon atom topology of the C₆₀ fullerene have been synthesized. Different numbers of fluorine atoms were introduced in the key positions, as needed for an efficient intramolecular condensation to the fullerene molecule. The polycyclic aromatic compounds obtained represent attractive precursors for rational, high-yield fullerene synthesis by flash vacuum pyrolysis.     

Charged native β-cyclodextrin as a pseudostationary phase in electrokinetic chromatography

Native β-cyclodextrin, deprotonated at its secondary hydroxyl groups has been studied as pseudostationary phase for electrokinetic chromatographic separation of highly hydrophobic compounds. Using this pseudostationary phase the separation of five polycyclic aromatic hydrocarbons (PAHs) is shown. The influence of the main parameters (field strength, pH, concentration of cyclodextrin, urea and organic solvent) on the separation of PAHs and migration behaviour of β-CD is discussed. Received:17 November 1995 / Revised: 7 February 1996 / Accepted: 10 February 1996     

Friedel-Crafts alkylation of a cage enone: synthesis of aralkyl substituted tetracyclo[5.3.1.0.0]undeca-9,11-diones and the formation of fascinating novel cage compounds with pyrrole and thiophene using Montmorillonite K-10

The intrinsic catalytic properties of Montmorillonite K-10 clay have been utilized for Friedel-Crafts alkylation of the polycyclic caged enone 1 using different carbo and heterocyclic aromatic systems leading to novel compounds. Carbon-carbon bond formation between the aromatic compounds and the cage system has led to three different types of products.     

A Metal‐Bridged Tricyclic Aromatic System: Synthesis of Osmium Polycyclic Aromatic Complexes

Aromaticity is one of the most important concepts in organic chemistry. A variety of metalla‐aromatic compounds have been recently prepared and in most of those examples, the metal participates only in a monocyclic ring. In contrast, metal‐bridged bicyclic aromatic molecules, in which a metal is shared between two aromatic rings, have been less developed. Herein, we report the first metal‐bridged tricyclic aromatic system, in which the metal center is shared by three aromatic five‐membered rings. These metalla‐aromatics are formed by reaction between osmapentalyne and arene nucleophiles. Experimental results and theoretical calculations reveal that the three five‐membered rings around the osmium center are aromatic. In addition, the broad absorption bands in the UV/Vis absorption spectra of these novel aromatic systems cover almost the entire visible region. This straightforward synthetic strategy may be extended to the synthesis of other metal‐bridged polycyclic aromatics.     

Methodology for Bioassay-Directed Fractionation Studies of Air Particulate Material and Other Complex Environmental Matrices

Abstract

A normal phase HPLC methodology using a semi-preparative polyaminocyano column in conjunction with a selection of short-term genotoxicity assays has been developed for bioassay-directed fractionation studies of complex environmental mixtures. To illustrate the effectiveness of this methodology, an organic extract prepared from respirable air particulate samples collected in Hamilton, Canada was separated into a non-polar aromatic fraction and a polar aromatic fraction using a combination of alumina and Sephadex LH20 chromatography. These fractions were evaluated for their genotoxic potential using the Salmonella/microsome (Ames) assay with six different strains of Salmonella.

The non-polar aromatic fraction was analyzed by normal phase HPLC and the eluent was collected in one-minute subfractions; these subtractions were bioassayed in three different Salmonella strains (YG1021 -S9, YG1024 -S9 and YG1029 +S9) to afford three different mutation profiles of this sample. Some subfractions which exhibited high mutagenic responses were subjected to further chemical analyses using GC/MS in order to identify those compounds responsible for the genotoxic responses. The nitroarene compounds 2-nitrofluoranthene, 1-nitropyrene and 2-nitropyrene and higher molecular weight polycyclic aromatic hydrocarbons such as benzo[a]pyrene and indeno[l,2,3-cd]pyrene were identified and quantified in some of the biologically active subfractions. The normal phase gradient conditions afforded very reproducible retention times for a series of polycyclic aromatic standards with a broad range of compound polarities. In addition, polycyclic aromatic hydrocarbons (PAH) were observed to elute from the normal phase HPLC column in a series of peaks; successive peaks contained PAH of increasing molecular weight while any individual peak was shown to contain PAH of the same molecular weight.     

Elution of organic solutes from different polarity sorbents using subcritical water

The intermolecular interactions between organic solutes and sorbent matrices under subcritical water conditions have been investigated at a pressure of 50 bar and temperatures ranging from 50 to 250°C. Both polar and nonpolar organics (chlorophenols, amines, n-alkanes, and polycyclic aromatic hydrocarbons) and five different sorbent matrices (glass beads, alumina, Florisil, silica-bonded C₁₈, and polymeric XAD-4 resins) were used. From the same matrix, the polar solutes always eluted at lower temperatures, while the moderately polar and nonpolar solutes only eluted at higher temperatures. Similar to matrix effects previously observed using supercritical carbon dioxide, the sorbent type greatly influenced the elution efficiency under subcritical water conditions. Lower temperatures are sufficient to elute a particular solute from glass beads, alumina, and Florisil, but higher temperatures (less polar water) are needed to elute the same solute from silica-bonded C₁₈. The highest temperatures were required to elute aromatic organics from XAD-4. These matrix effects demonstrate that, while low temperature water can break inert or dipole interactions between solutes and glass beads, alumina, and Florisil, higher temperature water is required to interrupt the van der Waals attractions between solutes and silica-bonded C₁₈, and even higher temperatures needed to overcome the π-electron interactions between aromatic solutes and XAD-4.     

Separation of polar and non-polar analytes using dimethyl sulfoxide-modified subcritical water

Separations using methanol–water or acetonitrile–water mixtures at different temperatures have been well investigated in reversed-phase liquid chromatography. However, reversed-phase separation with dimethyl sulfoxide (DMSO)–water mixtures is much less studied. In this work, separations of polyhydroxybenzenes, phenol derivatives, benzene, toluene, ethylbenzene, and xylenes (BTEX), and polycyclic aromatic hydrocarbons (PAHs) with DMSO-modified subcritical water were performed at several temperatures to evaluate the effect of temperature on the elution strength of DMSO–water mixtures. The column efficiency obtained by using DMSO-modified subcritical water was also studied. Finally, the resolution of ethylbenzene and p-xylene was investigated.     

Review of Sublimation Thermodynamics of Polycyclic Aromatic Compounds and Heterocycles

This review details sublimation vapor pressure and thermodynamic data on 85 polycyclic aromatic compounds and heterocycles from the early 1900s through 2012. These data were collected using a variety of vapor pressure measurement techniques, from effusion to gas saturation to inclined‐piston manometry. A brief overview of each measurement technique is given; these methods yield reproducible sublimation vapor pressure data for low volatility organic compounds such as polycyclic aromatic compounds and heterocycles. Several conclusions can be drawn from this literature survey, specifically that there remains a dearth of data on the sublimation thermodynamics (and fusion thermodynamics) of heteroatomic high molecular weight aromatic compounds, inhibiting a holistic understanding of the effect of specific heteroatoms and substituent position on the thermodynamics of these compounds. However, we can clearly see from the data that there are a variety of potential intermolecular interactions at work that generally tend to increase the enthalpy of sublimation and decrease the vapor pressure of a substituted polycyclic aromatic compound/polycyclic heterocycles versus its parent compound.     

Triflic acid promoted synthesis of polycyclic aromatic compounds

The triflic acid (CF₃SO₃H) promoted cyclizations of 2-styrylbiaryls are found to be useful for the synthesis of polycyclic aromatic compounds, including functionalized derivatives of polycyclic aromatic compounds and heterocyclic systems. The reaction involves cationic cyclization followed by an elimination of benzene from the intermediate product.     

Determination of oxygen and nitrogen derivatives of polycyclic aromatic hydrocarbons in fractions of asphalt mixtures using liquid chromatography coupled to mass spectrometry with atmospheric pressure chemical ionization

Liquid chromatography coupled to mass spectrometry with atmospheric pressure chemical ionization was used for the determination of polycyclic aromatic hydrocarbon derivatives, the oxygenated polycyclic aromatic hydrocarbons and nitrated polycyclic aromatic hydrocarbons, formed in asphalt fractions. Two different methods have been developed for the determination of five oxygenated and seven nitrated polycyclic aromatic hydrocarbons that are characterized by having two or more condensed aromatic rings and present mutagenic and carcinogenic properties. The parameters of the atmospheric pressure chemical ionization interface were optimized to obtain the highest possible sensitivity for all compounds. The detection limits of the methods ranged from 0.1 to 57.3 μg/L for nitrated and from 0.1 to 6.6 μg/L for oxygenated derivatives. The limits of quantification were in the range of 4.6–191 μg/L for nitrated and 0.3–8.9 μg/L for oxygenated derivatives. The methods were validated against a diesel particulate extract standard reference material (National Institute of Standards and Technology SRM 1975), and the obtained concentrations (two nitrated derivatives) agreed with the certified values. The methods were applied in the analysis of asphalt samples after their fractionation into asphaltenes and maltenes, according to American Society for Testing and Material D4124, where the maltenic fraction was further separated into its basic, acidic, and neutral parts following the method of Green. Only two nitrated derivatives were found in the asphalt sample, quinoline and 2‐nitrofluorene, with concentrations of 9.26 and 2146 mg/kg, respectively, whereas no oxygenated derivatives were detected.     

beta-Cyclodextrin as a stationary phase for the group separation of polycyclic aromatic compounds in normal-phase liquid chromatography

The separation of highly alkylated polycyclic aromatic compounds according to the size of their aromatic system is investigated using the polycyclic aromatic sulfur heterocycles in vacuum gas oil. A large number of reference compounds containing several parent ring systems and different alkylation patterns were first investigated to characterize the retention of polycyclic aromatic compounds likely to occur in high-boiling petroleum samples. A beta-cyclodextrin phase, Merck ChiraDex, was found to be more suitable than chemically bonded aminopropanosilane and tetrachlorophthalimide in normal-phase HPLC with respect to a combination of selectivity towards the number of aromatic double bonds and degree of influence of the alkyl groups of the aromatic compounds. Finally the preseparated polycyclic aromatic sulfur heterocycles from a vacuum gas oil were fractionated according to the number of condensed aromatic rings on the ChiraDex phase and were characterized by Fourier transform ion cyclotron resonance mass spectrometry.     

Argentation chromatography for the separation of polycyclic aromatic compounds according to ring number

Crude oils are the most complex mixtures known and every speciation method relies on a simplification of their complexity. Argentation chromatography is shown to be superior to traditional liquid chromatographic ways of separating aromatic compounds based on the number of aromatic carbon atoms. A silver(I) mercaptopropano silica gel allows an efficient group separation of polycyclic aromatic compounds to be achieved. The usefulness of this phase is demonstrated for SRM 1582 Wilmington crude oil and a diesel fuel. Furthermore, the phase can also be used for semi-preparative purposes to collect fractions for further analysis with high resolution mass spectrometry. Orbitrap mass spectra are obtained here for the polycyclic aromatic sulfur heterocycles and it is demonstrated that they can contain one to five naphtheno rings.     

Hydroxyundecanethiol-Modified Steel Fibers for the Selective Solid-Phase Microextraction of Polycyclic Aromatic Hydrocarbons from River and Wastewater

A novel organic–inorganic composite-coated fiber was developed for selective solid-phase microextraction (SPME) by direct electrodeposition of zinc oxide microparticles on a pretreated stainless steel wire followed by self-assembly of hydroxyundecanethiol with zinc–sulfur bonds. The performance of the hydroxyundecyl-modified zinc oxide-coated steel fiber was then assessed for SPME of polar aromatic compounds coupled to high-performance liquid chromatography with ultraviolet detection. Excellent extraction and selectivity were obtained for polycyclic aromatic hydrocarbons. The extraction and desorption times, temperature, stirring rate, and ionic strength were optimized. The limits of detection were from 0.034 to 0.132?µg?L^?1. The relative standard deviations were from 3.4 to 4.9% for a single fiber and from 5.1 to 6.4% for multiple fibers. The recovery of polycyclic aromatic hydrocarbons in environmental water fortified at 5.0 and 50?µg?L^?1 was from 83.1 to 103% with relative standard deviations below 8.4%. This fiber was shown to withstand at least 200 extraction and desorption cycles. The method was used for the preconcentration and determination of polycyclic aromatic hydrocarbons in environmental water.     

Effect of the chain length on the thermal and analytical properties of laterally biforked nematogens

Three laterally substituted liquid crystals were synthesized in order to investigate the effect of a lateral biforked chain on the thermal and analytical properties. The mesogenic molecules have the same core containing four aromatic rings connected by two ester and one diazo linkages, they differ by the length of one chain within the lateral biforked substituent. The phase transition temperatures were obtained by polarized light microscopy and differential scanning calorimetry (DSC). The clearing temperature and the nematic range decrease with increasing length of the lateral biforked chain. The stationary phases derived from these nematogens provide excellent resolution of various classes of compounds, including aromatic hydrocarbons (AH), substituted benzenes, polycyclic aromatic hydrocarbons (PAH), phenols and volatile organic compounds (VOC) present in the essential oils. The selectivities of the stationary phases were found to decrease according to the length of the side chain.