Tertiary amine-functionalized polymers by atom transfer radical polymerization

The quantitative synthesis of tertiary amine-functionalized polymers by atom transfer radical polymerization is reported. Tertiary amine-functionalized polystyrene was prepared with the adduct of 1-(bromoethyl)benzene with 1-(4-dimethyl-aminophenyl)-1-phenylethylene as an initiator in the atom transfer radical polymerization of styrene in the presence of a copper (I) bromide/2,2′-bipyridyl catalyst system. The polymerization proceeded via a controlled free-radical polymerization process to afford quantitative yields of the corresponding tertiary amine-functionalized polystyrene with predictable number-average molecular weights (1600–4400), narrow molecular weight distributions (1.09–1.31), and an initiator efficiency of 0.95. The polymerization process was monitored by gas chromatographic analysis. The tertiary amine-functionalized polymers were characterized by thin-layer chromatography, size exclusion chromatography, potentiometry, and spectroscopy. All experimental evidence was consistent with quantitative functionalization via the 1,1-diphenylethylene derivative. Polymerization kinetic measurements showed that the polymerization reaction followed first-order-rate kinetics with respect to monomer consumption and that the number-average molecular weight increased linearly with monomer conversion. © 2001 John Wiley & Sons, Inc. J Polym Sci A Part A: Polym Chem 39: 2058–2067, 2001     

Aqueous electrochemically-triggered atom transfer radical polymerization

Simplified electrochemical atom transfer radical polymerization (seATRP) using Cu^II–N-propyl pyridineimine complexes (Cu^II(NPPI)₂) is reported for the first time. In aqueous solution, using oligo(ethylene glycol) methyl ether methacrylate (OEGMA), standard electrolysis conditions yield POEGMA with good control over molecular weight distribution (Đ_m < 1.35). Interestingly, the polymerizations are not under complete electrochemical control, as monomer conversion continues when electrolysis is halted. Alternatively, it is shown that the extent and rate of polymerization depends upon an initial period of electrolysis. Thus, it is proposed that seATRP using Cu^II(NPPI)₂ follows an electrochemically-triggered, rather than electrochemically mediated, ATRP mechanism, which distinguishes them from other Cu^IIL complexes that have been previously reported in the literature.

Simplified electrochemical atom transfer radical polymerization (seATRP) using Cu^II-pyridineimine complexes is reported and follows a previously unreported electrochemically triggered mechanism.     

原子转移自由基聚合研究进展

原子转移自由基聚合(Atom transfer radical polymerization,ATRP)是一种发展较快的可控/活性聚合技术,现已广泛应用于聚合物分子结构设计及众多功能高分子材料的合成.本文在综述了ATRP的反应机理的基础上,介绍了引发剂、催化剂、配体、单体等对ATRP的影响,同时综述了降低(或去除)金属盐含量的绿色、高效ATRP聚合体系,如引发剂持续再生活化ATRP,电子转移生成(再生)活化剂ATRP,铁催化体系,光催化体系等.近年来发展的无金属光诱导的有机催化ATRP聚合体系也做了综述.     

Functional virus-based polymer-protein nanoparticles by atom transfer radical polymerization

Viruses and virus-like particles (VLPs) are useful tools in biomedical research. Their defined structural attributes make them attractive platforms for engineered interactions over large molecular surface areas. In this report, we describe the use of VLPs as multivalent macroinitiators for atom transfer radical polymerization. The introduction of chemically reactive monomers during polymerization provides a robust platform for post-synthetic modification via the copper-catalyzed azide-alkyne cycloaddition reaction. These results provide the basis to construct nanoparticle delivery vehicles and imaging agents using protein-polymer conjugates.     

Dehalogenation of polymers prepared by atom transfer radical polymerization

Polymers prepared by atom transfer radical polymerization (ATRP) have well‐defined end groups, predetermined by the initiator used. A typical initiator is an alkyl halide from which the halogen is transferred to one chain end. To remove the halogen end group, dehalogenation with trialkyltin hydride has been used. Procedures for the removal of the polymer halogen end groups are described, one of them being a one‐pot reaction where the dehalogenation of the polymer chain ends occurs immediately after polymerization.     

Graft copolymers of polyethylene by atom transfer radical polymerization

Poly(ethylene‐g‐styrene) and poly(ethylene‐g‐methyl methacrylate) graft copolymers were prepared by atom transfer radical polymerization (ATRP). Commercially available poly(ethylene‐co‐glycidyl methacrylate) was converted into ATRP macroinitiators by reaction with chloroacetic acid and 2‐bromoisobutyric acid, respectively, and the pendant‐functionalized polyolefins were used to initiate the ATRP of styrene and methyl methacrylate. In both cases, incorporation of the vinyl monomer into the graft copolymer increased with extent of the reaction. The controlled growth of the side chains was proved in the case of poly(ethylene‐g‐styrene) by the linear increase of molecular weight with conversion and low polydispersity (M_w /M_n < 1.4) of the cleaved polystyrene grafts. Both macroinitiators and graft copolymers were characterized by ¹H NMR and differential scanning calorimetry. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 2440–2448, 2000     

Structure-reactivity correlation in atom transfer radical polymerization

Kinetics of atom transfer radical polymerization (ATRP) with the special emphasis on dynamics of activation and deactivation is discussed. Various mechanistic features of ATRP related to electron transfer processes are presented. Elementary reactions of ATRP process are analyzed.     

Graft polymerization of polysilsesquioxane containing chloromethylphenyl groups by atom transfer radical polymerization

Polysilsesquioxane with phenyl and chloromethylphenyl groups (PCPSQ) was prepared readily from phenyltrimethoxysilane and [2‐(chloromethylphenyl)ethyl]trimethoxysilane under acidic conditions. Polymerization with chloromethylphenyl groups on PCPSQ with methyl methacrylate (MMA) was conducted in the presence of a catalytic amount of copper(I) bromide and (−)‐sparteine. Atom transfer radical polymerization yielded a graft polymer (PCPSQ‐g‐MMA) efficiently, and no gelation was observed. The process was also applied to the preparation of graft block copolymers on PCPSQ with several methacrylate monomers. An advantage of the graft hybrid polymers was shown in improved thermal behavior. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 4212–4221, 2004     

Electron transfer reactions relevant to atom transfer radical polymerization

The continuous development of more active and stable catalysts in atom transfer radical polymerization (ATRP) has increasingly required a thorough knowledge of concurrent electron transfer reactions that can affect catalyst performance. Special attention is provided in this short review to such processes, including disproportionation, most pronounced in Cu-mediated ATRP, the reduction of radicals to carbanions or oxidation to carbocations, and radical coordination to the metal catalyst resulting in the interplay of controlled radical polymerization mechanisms.     

Controlled polymerization of (meth)acrylamides by atom transfer radical polymerization

Controlled polymerization of (meth)acrylamides was achieved by ATRP using the initiating system methyl 2‐chloropropionate/CuCl/tris(2‐dimethylaminoethyl)amine. Linear increase of molecular weights with conversion and low polydispersity (M_w/M_n < 1.2) were obtained in toluene, at room temperature, when N,N‐dimethylacrylamide was used as a monomer. However, the polymerization reached limited conversion, which could be enhanced by increasing the catalyst/initiator ratio. The limited conversion is not due to the loss of the active chains, but rather to the loss of activity of the catalytic system.     

Synthesis of diblock copolymers by combining stable free radical polymerization and atom transfer radical polymerization

A stable nitroxyl radical functionalized with an initiating group for atom transfer radical polymerization (ATRP), 4‐(2‐bromo‐2‐methylpropionyloxy)‐2,2,6,6‐tetramethyl‐1‐piperidinyloxy (Br‐TEMPO), was synthesized by the reaction of 4‐hydroxyl‐2,2,6,6‐tetramethyl‐1‐piperidinyloxy with 2‐bromo‐2‐methylpropionyl bromide. Stable free radical polymerization of styrene was then carried out using a conventional thermal initiator, dibenzoyl peroxide, along with Br‐TEMPO. The obtained polystyrene had an active bromine atom for ATRP at the ω‐end of the chain and was used as the macroinitiator for ATRP of methyl acrylate and ethyl acrylate to prepare block copolymers. The molecular weights of the resulting block copolymers at different monomer conversions shifted to higher molecular weights and increased with monomer conversion. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2468–2475, 2006     

Synthesis of a well-defined glycopolymer by atom transfer radical polymerization

Controlled free radical polymerization of sugar-carrying methacrylate, 3-O-methacryloyl-1,2 : 5,6-di-O-isopropylidene-d-glucofuranose (MAIpGlc) was achieved by the atom transfer radical polymerization (ATRP) technique with an alkyl halide/copper-complex system in veratrole at 80°C. The time–conversion first-order plot was linear and the number-average molecular weight increased in direct proportion to the ratio of the monomer conversion to the initial initiator concentration, providing PMAIpGlc with a low polydispersity. The sequential addition of the two monomers styrene (S) and MAIpGlc afforded a block copolymer of the type PS-b-PMAIpGlc. The acidolysis of the homo- and block copolymers gave well-defined glucose-carrying water-soluble polymers PMAGlc and PS-b-PMAGlc, respectively. The amphiphilic PS-b-PMAGlc block copolymer exhibited a microdomain surface morphology with spherical PS domains in a PMAGlc matrix. © 1998 John Wiley & Sons, Inc. J. Polym. Sci. A Polym. Chem. 36: 2473–2481, 1998     

New (Co)polymers by atom transfer radical polymerization

The fundamentals of atom transfer radical polymerization (ATRP) are presented. This includes the mechanistic considerations including structure of active and dormant species and structural features of the catalyst and reaction conditions as well as the nature of initiation and propagation steps. Extension of homogeneous polymerization to heterogeneous systems including emulsion polymerization is presented. Synthesis of (co)polymers with predefined molecular weights and low polydispersites as well as with controlled compositions, functionalities and architectures is reviewed.     

Synthesis of star-shaped metallo-polymeric chromophores by atom transfer radical polymerization

The synthesis of bromoester-functionalized dialkylaminostyryl-2,2′-bipyridyl ligands and of the corresponding tris[dialkylaminostyryl-2,2′-bipyridine] metal(II) complexes are reported (M = Fe, Ru, Zn). These complexes are used as multifunctional metallo-initiators for the atom transfer radical polymerization (ATRP) of methyl methacrylate. The resulting new star-shaped polymers combine the optical (UV–visible and luminescence) properties of the monomers with good processability, which allow to build high optical quality thin films by the spin-coating technique. To cite this article: L. Viau et al., C. R. Chimie 8 (2005).     

New antibacterial cationic surfactants prepared by atom transfer radical polymerization

Efficient antibacterial surfactants have been prepared by the quaternization of the amino groups of poly(ethylene‐co‐butylene)‐b‐poly[2‐(dimethylamino)ethylmethacrylate] (PEB‐b‐PDMAEMA) diblock copolymers by octyl bromide. The diblock copolymers have been synthesized by ATRP of 2‐(dimethylamino)ethylmethacrylate (DMAEMA) initiated by an activated bromide‐end‐capped poly(ethylene‐co‐butylene). In the presence of CuBr, 1,4,7,10,10‐hexamethyl‐triethylenetetramine (HMTETA), and toluene at 50 °C, the initiation is slow in comparison with propagation. This situation has been improved by the substitution of CuCl for CuBr, all the other conditions being the same. Finally, the addition of an excess of CuCl₂ (deactivator) to the CuCl/HMTETA catalyst is very beneficial in making the agreement between the theoretical and experimental number‐average molecular weights excellent. The antibacterial activity of PEB‐b‐PDMAEMA quaternized by octyl bromide has been assessed against bacteria and is comparable to the activity of a commonly used disinfectant, that is, benzalkonium chloride. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 1214‐1224, 2006     

Synthesis of random polyampholyte brushes by atom transfer radical polymerization

We report the synthesis of random polyampholyte brushes containing 2‐(dimethylamino)ethyl methacrylate (DMAEMA) and methacrylic acid (MAA). The preparation of polyampholyte brushes is performed by the “grafting from” strategy using surface‐initiated atom transfer radical polymerization (ATRP). The first step consists in the formation of the self‐assembled monolayer of the ATRP initiator. Secondly, the chains are grown from the surface by controlled/“living” radical polymerization. The random copolymer brushes and the corresponding homopolymers brushes containing 2‐(dimethylamino)ethyl methacrylate and tert‐butyl methacrylate (^tBuMA) are prepared. The last step is the deprotection of the ^tBuMA form to the MAA segment by in situ hydrolysis reaction. The annealed DMAEMA group can also be converted to the quenched form by in situ quaternization reaction. This results in the formation of “annealed” and “semiannealed” polyampholyte brushes. The “annealed” polyampholyte corresponds to the random copolymer that contains only annealed units, weak acid and weak base. The “semiannealed” polyampholyte consists of the mixture of annealed (weak acid) and quenched (quaternized segment) units. Polyampholyte brushes with various grafting densities are synthesized and carefully characterized using surface techniques such as ellipsometry and FTIR‐ATR. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 4305–4319, 2008     

Synthesis of semifluorinated block copolymers by atom transfer radical polymerization

Two sets of styrene‐based semifluorinated block copolymers, one with a perfluoroether pendant group and another with a perfluoroalkyl group, were synthesized by atom transfer radical polymerization. Microphase separation of the block copolymers was established by small‐angle X‐ray scattering and differential scanning calorimetry (DSC). DSC measurements also showed that the perfluoroether‐based polymer had a low glass‐transition temperature (?44 °C). Contact‐angle measurements indicated that the semifluorinated block copolymers had low surface energies (ca. 13 mJ/m²). These materials hold promise as low‐surface‐energy additives or surfactants for supercritical CO₂ applications. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 853–861, 2004     

Bulk atom transfer radical polymerization of allyl methacrylate

A detailed investigation of the polymerization of allyl methacrylate, a typical unsymmetrical divinyl compound containing two types of vinyl groups, methacryloyl and allyl, with quite different reactivities, was performed with atom transfer radical polymerization (ATRP). Homopolymerizations were carried out in bulk, with ethyl‐2‐bromoisobutyrate as the initiator and with copper halide (CuX, where X is Cl or Br) with N,N,N′,N″,N″‐pentamethyldiethylenetriamine as the catalyst system. Kinetic studies demonstrated that during the early stages of the polymerization, the ATRP process proceeded in a living manner with a low and constant radical concentration. However, as the reaction continued, the increased diffusion resistance restricted the mobility of the catalyst system and interrupted the equilibrium between the growing radicals and dormant species. The obtained poly(allyl methacrylate)s (PAMAs) were characterized with Fourier transform infrared, ¹H NMR, and size exclusion chromatography techniques. The dependence of both the gel point conversion and molecular characteristics of the PAMA prepolymers on different experimental parameters, such as the initiator concentration, polymerization temperature, and type of halide used as the catalyst, was analyzed. These real gel points were compared with the ones calculated according to Gordon's equation under the tentative assumption of equal reactivity for the two types of vinyl groups. Moreover, the microstructure of the prepolymers was the same as that exhibited by those homopolymers prepared by conventional free‐radical polymerization; the fraction of syndiotactic arrangements increased as the reaction temperature was lowered. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 2395–2406, 2005     

Living atom transfer radical polymerization of 4-acetoxystyrene

Living atom transfer radical polymerization (ATRP) of 4-acetoxystyrene ( 1 ), a protected 4-vinylphenol, leading to poly(4-acetoxystyrene) with well-defined molecular weight and narrow molecular weight distribution was carried out in bulk with α,α′-dibromoxylene( 2 )/CuBr/2,2-bipyridine(bpy) as initiating system. A linear M̄_n versus monomer conversion plot was found in good accordance with the theoretical line, indicating 100% initiating efficiency. The polymerization is first order in respect to monomer up to about 70% monomer conversion. Deviations from linearity at higher conversion in the first order plot are due to physical effects, i.e., to the increase of the viscosity of the reaction medium. The resulting 1-bromo-1-phenylethyl-telechelic poly(4-acetoxystyrene) ( 3 ) is a precursor of the hydrophilic poly(4-vinylphenol) and a potential new macroinitiator.