中心对称双酞菁铥LB膜二次谐波产生特性

利用二次谐波产生(SHG)方法研究了中心对称分子稀土夹心双酞菁铥(TmPc₂) Langmuir-Blodgett (LB)膜二阶非线性光学特性, 测量了二次谐波强度随入射基频光入射角的关系, 并对其二阶非线性产生机制进行了讨论. 实验结果表明, TmPc₂分子LB膜具有较好的二次谐波信号, 二次谐波信号强度的最大值在基频光入射角为45°的地方, 其二阶非线性极化率χ⁽²⁾和分子超极化率β分别为1.152×10^-8和1.905×10^-30 esu. 通过测量样品二次谐波信号的偏振特性, 并与理论分析相比较, 得出其二阶非线性起源于电四极子作用机制.     

Scanning angle Raman spectroscopy measurements of thin polymer films for thickness and composition analyses

Scanning angle (SA) Raman spectroscopy was used to measure the thickness and composition of polystyrene films. A sapphire prism was optically coupled to a sapphire substrate on which 6–12% (w/v) polystyrene in toluene was spin coated. Raman spectra were collected as the incident angle of the p-polarized, 785-nm excitation laser was varied from 56 to 70°. These angles span above and below the critical angle for a sapphire/polystyrene interface. The thickness of the polystyrene film was determined using a calibration curve constructed by calculating the integrated optical energy density distribution as a function of incident angle, distance from the prism interface and polymer thickness. The calculations were used to determine the incident angle where waveguide modes are excited within the polymer film, which is the angle with the highest integrated optical energy density. The film thicknesses measured by SA Raman spectroscopy ranged from less than 400 nm to 1.8 μm. The average percent uncertainty in the SA Raman determinations for all films was 4%, and the measurements agreed with those obtained from optical interferometery within the experimental uncertainty for all but two films. For the 1270-nm and 580-nm polystyrene films, the SA Raman measurements overestimated the film thickness by 5 and 18%, respectively. The dependence of the calibration curve on excitation polarization and composition of the polymer and bulk layers was evaluated. This preliminary investigation demonstrates that scanning angle Raman spectroscopy is a versatile method applicable whenever the chemical composition and thickness of interfacial polymer layers needs to be measured.     

Second harmonic generation at the interface of copper tetra-tert-butyl phthalocyanine Langmuir-Blodgett film/metal

As one of the most primitive nonlinear optical phenomena, optical second harmonic genera-tion (SHG) has been investigated for half a century and it has become a very useful spectroscopic tool in the study of surface and interface[1—3]. It was theoretically shown that the SH signal cannot be generated in a centrosymmetric system. However, the generation of SH signal from the centro-symmetric molecules such as fullerene (C60) and CuPc has been detected[4—7]. In our recent ex-periments, an …     

Electron-beam-induced conduction in fluorinated ethylene propylene copolymer and its acrylonitrile graft copolymer

Electron-beam-induced conductivity (EBIC) studies were carried out on fluorinated ethylene propylene copolymer (FEP) and its acrylonitrile graft copolymer (FEP-g-AN). The current transport parallel to the surface under the influence of an electron beam of medium energy (6–30 keV) is reported. The gain in EBIC is calculated and its characteristic variation as a function of beam energy is studied. Minima in the gain versus energy curves have been obtained around 21 keV for FEP, 12 and 18 keV for FEP-g-AN, and 12 keV for polyacrylonitrile (PAN). This behavior is explained by assuming the existence of electron trapping bands close to the surface, at characteristic distances below the surface of the polymeric film corresponding to the range of incident electrons. Gains of the order of 5, 12, and 30 have been obtained respectively for FEP, FEP-g-AN, and PAN for the maximum energy of incident electrons used.     

Polarization dependence of Raman scattering from a thin film involving optical anisotropy theorized for molecular orientation analysis

Polarized Raman scattering from a thin film involving uniaxial optical anisotropy deposited on a dielectric substrate has analytically been theorized. The analyte film is modeled as a three-phase system (air/film/substrate) to calculate the electromagnetic fields of the incident and scattered light propagating across the system with an aid of the transfer matrix method to exactly take the optical anisotropy of the film into account. On the new theory, a methodology for molecular orientation analysis of an extended polymethylene chain in the film is proposed, which is employed for determination of the tilt angles of the chains in single- and five-monolayer Langmuir-Blodgett (LB) films of cadmium stearate deposited on a glass plate. The results agree well with those obtained by infrared spectroscopy, which confirms reliability of the present method.     

钒氧酞菁薄膜瞬态光电压性能的研究

本文分别用1064nm, 532nm和 355nm激发波长的YAG脉冲激光对所制备的phase Ⅱ结构钒氧酞菁膜Al\phase ⅡVOPc\ITO夹心电池进行瞬态光电压响应研究.随着3种波长激发光脉冲强度的增加, 瞬态光电压信号均增强. 激发光波长1064nm、532nm处于酞菁膜Q-带吸收区肩部, 光电压的极性与激发光入射方向无关, 均为负信号; 而激发光波长 355nm处于酞菁膜B-带, 光电压的极性与激发光入射方向有关, 从ITO极方向激发产生正电压信号, 从A1极激发产生负电压信号. 激发光波长对夹心电池的光电压产生有明显的作用, 光电压产生过程中应存在不同的机理. 这与前文^[1]对同一夹心电池稳态光电压响应研究所推断的结论一致.     

Signal stability of Nafion-coated thin mercury film electrodes for stripping voltammetry

The signal stability of the Nafion-coated thin mercury film electrode (NCTMFE) was studied by using cadmium and lead as test analytes and differential pulse anodic stripping voltammetry as detection method. In particular, the effect of the casting solvent and the curing procedure employed in the preparation of the polymer film was examined. Best results were obtained with N,N-dimethylacetamide as casting solvent and a two-step curing procedure in which the polymer was evaporated to dryness at 55 degrees and cured at 105 degrees with a hot-air gun. Mercury plating was performed ex situ. An NCTMFE prepared in this manner has a better signal stability than ex situ-plated as well as in situ-plated conventional mercury film electrodes.     

Classical theory of two-dimensional time-domain terahertz spectroscopy

A general theoretical framework of two-dimensional time-domain second-order and third-order terahertz spectroscopy has been presented. The theoretical treatment is based on a classical and phenomenological model with weak nonlinearities. Three types of nonlinearity sources, anharmonicity, nonlinear coupling, and nonlinear damping, were considered. The second-order THz spectroscopy has an exact correspondence to fifth-order off-resonance Raman spectroscopy, and it has been shown that the present treatment gives exactly the same results as of the quantum mechanical theory under the weak nonlinearity condition. General expressions for the nonlinear signal have been obtained for a single-mode system, and numerical calculations for delta-function incident terahertz pulses were shown. For the third-order signal, two-level systems were also considered for comparison. Contributions of two types of incident pulse sequences have been studied separately in the third-order signals. Profiles of the two-dimensional signals were found to depend on the origin and order of the nonlinearity and also on the pulse sequence. The results of the present study show that the two-dimensional signal features of second- and third-order nonlinear terahertz spectroscopy can clarify the nature of the system which is not accessible using linear spectroscopy.     

The determination of copper at thin film electrodes by constant current stripping potentiometry

A comparison of the determination of copper by constant current stripping potentiometry (CCSP) at mercury and gold films has been carried out. The preferred solution conditions for the mercury film study were determined to be 0.1M ammonium acetate at pH 4.5 and 0.1M HCl for the gold film study. The influence of chloride on the stripping signal was investigated and it was found that for the mercury film conditions, well-formed stripping signals could be obtained up to a chloride concentration of 0.5 M which permitted the ready determination of copper in seawater. With the gold film, high chloride concentrations affected both the film stability and the glassy carbon surface and repeatable results were difficult to obtain. The optimized CCSP methods were applied to various aqueous samples including tap water, seawater, TCLP (acetic acid) extracts as well as TCLP extracts using groundwater and ocean water. Based on the results obtained for these various matrices, it was concluded that there are several advantages favoring the mercury film. The interference from organic components in the sample matrix on the general applicability of CCSP for the determination of copper at either a mercury or gold film is discussed.     

Directly assembled CdSe quantum dots on TiO2 in aqueous solution by adjusting pH value for quantum dot sensitized solar cells

We report an improved quantum dot sensitized solar cell (QDSSC) by loading mercaptopropionic acid (MPA)-capped CdSe QDs on TiO₂ film in aqueous solution. Under suitable pH value, a power conversion efficiency of 1.19% and an incident photon to current conversion efficiency of 26% for the QDSSC were obtained at AM1.5G irradiation. The improved performance of QDSSC is attributed to the large loading and good coverage of QDs on TiO₂ film with optimal pH value.     

Study of the properties and structure of nanosize membranes for acousto-optic devices

Polyimide films on BK7 glass, which are used to produce matrices for infrared detectors, have been synthesized. When these systems are investigated by monochromatic zero ellipsometry, the least difference between parameters of the incident light polarization, which are determined from suppression angles of polarizer and analyzer and calculated within a certain model, is obtained via introducing air between mounting glass and the film. Validity of the solution was verified by holding the film in water vapor; then, solution of the inverse problem of ellipsometry indicated the appearance of liquid water between the film and mounting glass. Data of the electron microscopy study were used to suggest a water penetration mechanism and develop a physical model of the system polyimide film/mounting glass.     

Microstructure and surface roughness of graphite‐like carbon films deposited on silicon substrate by molecular dynamic simulation

Molecular dynamics simulations are performed on the atomic origin of the growth process of graphite‐like carbon film on silicon substrate. The microstructure, mass density, and internal stress of as‐deposited films are investigated systematically. A strong energy dependence of microstructure and stress is revealed by varying the impact energy of the incident atoms (in the range 1–120 eV). As the impact energy is increased, the film internal stress converts from tensile stress to compressive stress, which is in agreement with the experimental results, and the bonding of C‐Si in the film is also increased for more substrate atoms are sputtered into the grown film. At the incident energy 40 eV, a densification of the deposited material is observed and the properties such as density, sp³ fraction, and compressive stress all reach their maximums. In addition, the effect of impact energy on the surface roughness is also studied. The surface morphology of the film exhibits different characteristics with different incident energy. When the energy is low (<40 eV), the surface roughness is reduced with the increasing of incident energy, and it reaches the minimum at 50 eV. Copyright © 2012 John Wiley & Sons, Ltd.     

Electrochemical Surface Plasmon Resonance Spectroscopy at Bilayered Silver/Gold Films

Bilayered silver/gold films (gold deposited on top of the silver film) were used as substrates for electrochemical surface plasmon resonance spectroscopy (EC-SPR). EC-SPR responses of electrochemical deposition/stripping of copper and redox-induced conformation changes of cytochrome c immobilized onto self-assembled monolayers preformed at these substrates were measured. Influence of the Ag layer thickness and the double-layer capacitance on the EC-SPR behavior was investigated. The results demonstrated that the bilayered Ag/Au metal films produce a sharper SPR dip profile than pure Au films and retain the high chemical stability of Au films. Contrary to the result by the Fresnel calculation that predicts a greater fraction of Ag in the bilayered film should result in a greater signal-to-noise ratio, the EC-SPR sensitivity is dependent on both the Ag/Au thickness ratio and the chemical modification of the surface. Factors affecting the overall SPR sensitivity at the bilayered films, such as the film morphology, potential-induced excess surface charges, and the adsorbate layer were investigated. Forming a compact adsorbate layer at the bilayered film diminishes the effect of potential-induce excess surface charges on the SPR signal and improves the overall EC-SPR sensitivity. For the case of redox-induced conformation changes of cytochrome c, the SPR signal obtained at the bilayered silver/gold film is 2.7 times as high as that at a pure gold film.     

基于自组装纳米金单层膜的全内反射SERS研究

采用静电自组装技术分别在玻璃基片和30 nm厚的金膜表面固定一层金纳米粒子(GNP)制得两种表面增强拉曼散射(SERS)基底,然后通过棱镜全内反射(TIR)激励和背向收集模式分别测试了两种基底上吸附的染料单分子层SERS光谱.实验结果表明两种SERS基底的拉曼增强效果均高度依赖于入射激光的偏振状态,对于玻璃/纳米金SERS基底,s光全内反射导致的拉曼增强因子是线偏振光(p)光的2-5倍,说明该基底上的"热点"位于纳米金单层膜内相邻粒子之间;对于玻璃/金膜/纳米金SERS基底,只有采用p光在特定的全内反射角下才能激发SERS信号,而且测得的SERS信号比玻璃/纳米金基底增强了近30倍.究其原因是p光在金膜表面共振激发的传播表面等离子体与纳米金局域表面等离子体耦合,进而导致显著场增强.实验结果指出在背向收集模式下,由p光激发的SERS信号是非偏振光,包含强度几乎相等的s和p成分.利用玻璃/金膜/纳米金基底还实现了拉曼光定向发射和收集,测得的SERS信号是p光.     

基于自组装纳米金单层膜的全内反射SERS研究

采用静电自组装技术分别在玻璃基片和30 nm厚的金膜表面固定一层金纳米粒子（GNP）制得两种表面增强拉曼散射（SERS）基底,然后通过棱镜全内反射（TIR）激励和背向收集模式分别测试了两种基底上吸附的染料单分子层SERS光谱. 实验结果表明两种SERS基底的拉曼增强效果均高度依赖于入射激光的偏振状态,对于玻璃/纳米金SERS基底,s 光全内反射导致的拉曼增强因子是线偏振光（p）光的2-5 倍,说明该基底上的“热点”位于纳米金单层膜内相邻粒子之间;对于玻璃/金膜/纳米金SERS基底,只有采用p光在特定的全内反射角下才能激发SERS信号,而且测得的SERS信号比玻璃/纳米金基底增强了近30 倍. 究其原因是p 光在金膜表面共振激发的传播表面等离子体与纳米金局域表面等离子体耦合,进而导致显著场增强. 实验结果指出在背向收集模式下,由p 光激发的SERS信号是非偏振光,包含强度几乎相等的s 和p 成分. 利用玻璃/金膜/纳米金基底还实现了拉曼光定向发射和收集,测得的SERS信号是p光.     

Optical phase grating diffraction in a quasistatic electric field biased nematic liquid crystal film

Abstract

It is known that an optical phase grating can be obtained when two mutually coherent laser beams overlap in a nematic liquid crystal. This is mainly due to director reorientation which contributes to a large optical non-linearity. It has been suggested by Herman and Serinko that a phase grating could be obtained in nematic liquid crystals if a D.C. field is used to bias it near the critical orientational Freedericksz transition. A homeotropic MBBA film biased by an electric field at 1 kHz has been studied. Two weak Ar⁺ laser beams were incident normally to the film with a small intersection angle (?0·4?). Using the picture of a director reorientation mechanism and a degenerate four wave mixing scheme, we have obtained the dependence of the diffraction beam intensity on that of the incident beam and the strength of the biased electric field. The theoretical prediction and experimental results both show that the phase grating diffraction can be dramatically enhanced by the coupling of the electric field to the optical field in the Freedericksz transition region. This is due to the critical behaviour of the sample at that transition. The prominently improved signal-to-noise ratio is discussed.     

Electrodeposited polythiophene films provide reproducible samples for laser desorption ion trap mass spectrometry studies

Electrodeposited polythiophene films can provide consistent laser desorption signal levels for over 20,000 laser shots on one position of a probe tip in an ion trap. A similar lack of signal decay was observed for multiple positions on the same film. The consistency and longevity of the ion signal resulting from laser desorption of a polythiophene film are much greater than those typically obtained from simple solution residue samples. Uniform, electrodeposited polythiophene films can provide a great reduction in the uncertainty of ion production that has previously been associated with ion trapping studies utilizing laser desorption.     

电沉积法制备金属纳米线阵列膜的偏光特性

Metal nanowire array films were prepared by electrodepositing Cu, Ag, Ni, Co and Cu-Ag on porous anodic alumina film. Optical transmittance of both the porous anodic alumina film and metal nanowire array film was measured in the wavelength range of 400---2600 nm under an obliquely incident light. The experimental results show that metal nanowire array films exhibit a prominent polarization function. It was found that optical polarization properties can be improved by choosing suitable kinds of electrodepositing metal, controlling the shape and length of nanowire, and changing the incident angle.     

Measurement of anisotropic refractive indices of free-standing polymer film

A new technique has been developed to measure the optical refractive indices in the parallel and perpendicular directions to the film surfaces and applied to measure the refractive indices of free-standing polymer films. The refractive indices were obtained by measuring the reflectivity as a function of the incident angle. The angle dependence of the reflectivity which results from the interference of the light beam reflected from the front and rear interfaces of the film was analysed by means of the Fresnel equation. This technique can be used to measure the refractive indices in three major axes, i.e. one out-of plane axis and two in-plane axes of the sample. This technique gives values for the refractive indices and the thickness simultaneously with an accuracy comparable to that measured by optical wave-guide technique. The validity of the technique has been tested with polymer films of known refractive indices such as poly(methyl methacrylate) and polyimide (PMDA-ODA).     

银纳米枝的合成及表面增强拉曼效应

利用硝酸银与铜之间发生置换反应原理, 在铜箔上得到了有序的银纳米枝结构, 用十二烷基磺酸钠(SDS)为表面活性剂, 通过调控前驱体硝酸银的浓度, 可在铜箔上得到不同密度的银纳米枝. 表面拉曼增强实验结果表明, 当分别以对巯基苯胺(4-ATP)、腺嘌呤和罗丹明G6为探针分子时, 有序的银纳米枝结构比无序的银纳米粒子具有更好的拉曼增强活性; 且随银纳米枝密度的增加, 表面拉曼增强活性有所提高. 该有序的银纳米枝结构是较好的表面增强拉曼(SERS)活性基底, 在有机分子和生物分子的SERS检测方面将具有一定的应用前景.