Critical evaluation of electrode design and matrix effects on monitoring organophosphate pesticides using composite carbon nanotube-modified electrodes

Carbon nanotubes (CNT)/Nafion-modified glassy carbon (GC) electrodes were used to immobilize the enzyme acetylcholinesterase (AChE) by crosslinking with glutaraldehyde. The CNT-modified electrodes exhibited a sensitive and stable electrocatalytic behavior towards thiocholine (TCh). Compared to ordinary GC electrodes modified with Nafion, a substantial (500-mV) decrease in the overvoltage of the TCh oxidation reaction is observed, along with a tenfold enhancement in the amperometric response. The CNT/Nafion/AChE electrode has very good stability of at least a month compared to surfaces made without crosslinking in the absence and presence of Nafion. Under optimal loadings of CNT, Nafion, AChE, and glutaraldehyde, a solution of CNT/Nafion in N,N-dimethylformamide (DMF) containing 4 mg/mL CNT and 0.01% Nafion was used to construct the electrodes in order to maximize the sensitivity of the biosensor for inhibition studies. An optimal enzyme loading of 0.137 U and crosslinking in 0.01% glutaraldehyde for 1 h was also needed to achieve this goal. The prepared electrodes had very good reproducibility to 1.0 mM acetylthiocholine (ATCh) (relative standard deviation [RSD] <5% for eight electrodes). Using paraoxon as a model pesticide, the biosensor was able to detect as low as 1.0 nM after 30 min of incubation at 30 °C. Using a log scale, the biosensor had good linearity in the concentration range 50?C800 nM, with a correlation coefficient of 0.99. The prepared biosensor was used to test real water samples spiked with paraoxon and showed good correlation with a calibration curve using phosphate buffer.     

ITO-free transparent conductive films based on carbon nanomaterials with metal grid for liquid crystal displays

Carbon nanomaterials with metal grids were used as transparent conductive electrodes for liquid crystal displays (LCDs) to develop an indium tin oxide (ITO)-free device. We prepared LCDs with CNTs and graphene electrodes; however, the working voltage of the device with the CNT electrodes was high. The device with graphene electrodes had good performance, but not as good as devices with ITO electrodes. To improve the device performance, we applied a metal grid to the carbon nanomaterial to create low sheet-resistance transparent electrodes. The device with the graphene and metal grid transparent electrodes had a threshold voltage as low as 0.23 V/µm, which is similar to that of typical LCDs with ITO electrodes. The results show that a hybrid transparent conductive film with graphene and metal grid could be an alternative to ITO for developing ITO-free LCDs.     

Electrochemical oxidation of catecholamines and catechols at carbon nanotube electrodes

The differences in the electrochemical oxidation of two commonly known catecholamines, dopamine and norepinephrine, and one catechol, dihydroxyphenylacetic acid (DOPAC), at three different types of carbon based electrodes comprising conventionally polished glassy carbon (GC), nitrogen-doped carbon nanotubes (N-CNTs), and non-doped CNTs were assessed. Raman microscopy and X-ray photoelectron spectroscopy (XPS) were employed to evaluate structural and compositional properties. Raman measurements indicate that N-CNT electrodes have ca. 2.4 times more edge plane sites over non-doped CNTs. XPS data show no evidence of oxygen functionalities at the surface of either CNT type. N-CNTs possess 4.0 at. % nitrogen as pyridinic, pyrrolic, and quaternary nitrogen functionalities that result in positively charged carbon surfaces in neutral and acidic solutions. The electrochemical behavior of the various carbon electrodes were investigated by cyclic voltammetry conducted in pH 5.8 acetate buffer. Semiintegral analysis of the voltammograms reveals a significant adsorptive character of dopamine and norepinephrine oxidation at N-CNT electrodes. Larger peak splittings, DeltaE(p), for the cyclic voltammograms of both catecholamines and a smaller DeltaE(p) for the cyclic voltammogram for DOPAC at N-CNT electrodes suggest that electrostatic interactions hinder oxidation of cationic dopamine and norepinephrine, but facilitate anionic DOPAC oxidation. These observations were supported by titrimetry of solid suspensions to determine the pH of point of zero charge (pH(pzc)) and estimate the number of basic sites for both CNT varieties. This study demonstrates that carbon purity, the presence of exposed edge plane sites, surface charge, and basicity of CNTs are important factors for influencing adsorption and enhancing the electrochemical oxidation of catecholamines and catechols.     

Amperometric glucose biosensor based on electrodeposition of platinum nanoparticles onto covalently immobilized carbon nanotube electrode

A new amperometric biosensor for glucose was developed based on adsorption of glucose oxidase (GOx) at the gold and platinum nanoparticles-modified carbon nanotube (CNT) electrode. CNTs were covalently immobilized on gold electrode via carbodiimide chemistry by forming amide linkages between carboxylic acid groups on the CNTs and amine residues of cysteamine self-assembled monolayer (SAM). The fabricated GOx/Au_nano/Pt_nano/CNT electrode was covered with a thin layer of Nafion to avoid the loss of GOx in determination and to improve the anti-interferent ability. The immobilization of CNTs on the gold electrode was characterized by quartz crystal microbalance technique. The morphologies of the CNT/gold and Pt_nano/CNT/gold electrodes have been investigated by scanning electron microscopy (SEM), and the electrochemical performance of the gold, CNT/gold, Pt_nano/gold and Pt_nano/CNT/gold electrodes has also been studied by amperometric method. In addition, effects of electrodeposition time of Pt nanoparticles, pH value, applied potential and electroactive interferents on the amperometric response of the sensor were discussed.

The enzyme electrode exhibited excellent electrocatalytic activity and rapid response for glucose in the absence of a mediator. The linear range was from 0.5 to 17.5 mM with correction coefficient of 0.996. The biosensor had good reproducibility and stability for the determination of glucose.     

Effect of the Dispersing Agent on the Electrochemical Response of Glassy Carbon Electrodes Modified with Dispersions of Carbon Nanotubes

The electrochemical response of a glassy carbon electrode modified with carbon nanotubes (CNT) dispersed in two solvents, water and DMF, and two polymers, chitosan and Nafion is reported. The films were homogeneous when the dispersing agent was water or DMF. In the case of polymers, the surfaces present areas with different density of CNTs. A more sensitive electrochemical response was obtained when CNTs are dispersed in the solvents. In the case of CNT dispersed with polymers, the nature of the polymer demonstrated to be a critical parameter not only for dispersing the nanotubes but also for the electrochemical activity of the resulting electrodes.     

Selective Determination of Quercetin Using Carbon Nanotube‐Modified Electrodes

Electrochemical detection of quercetin has been carried out on glassy carbon electrodes modified with carbon nanotubes and Nafion (GC/Nafion‐CNT). GC/Nafion‐CNT electrodes did not show passivation effect that occurs on the unmodified electrodes and displayed better stability and reproducibility. Quercetin oxidation was most favorable in acidic conditions and current gradually decreased as the solution pH increased. No oxidation was observed when two ? OH groups in a catechol moiety were fully deprotonated. These electrodes enabled selective determination of quercetin in the presence of interfering species such as ascorbic acid, uric acid, glucose, and catechol in large excess. Quantification of quercetin in a yellow onion has been made and favorably compared with reported values. Good selectivity and high sensitivity obtained by Osteryoung sSquare‐wave voltammetry can open new possibilities of direct quercetin determination in vegetables with a minimal sample treatment.     

Assembly of long carbon nanotube bridges across transparent electrodes using novel thickness-controlled dielectrophoresis

The assembly of carbon nanotubes (CNTs) across planner electrodes using dielectrophoresis (DEP) is one of the standard methods used to fabricate CNT-based devices such as sensors. The medium drag velocity caused by electrokinetic phenomena such as electrothermal and electroosmotic might drive CNTs away from the deposition area. This problem becomes critical at large-scale electrode structures due to the high attenuation of the DEP force. Herein, we simulated and experimentally validated a novel DEP setup that uses a top glass cover to minimize the medium drag velocity. The simulation results showed that the drag velocity can be reduced by 2–3 orders of magnitude compared with the basic DEP setup. The simulation also showed that the optimum channel height to result in a significant drag velocity reduction was between 100 μm and 240 μm. We experimentally report, for the first time, the assembly and alignment of CNT bridges across indium tin oxide (ITO) electrodes with spacing up to 125 μm. We also derived an equation to optimize the CNT's concentration in suspensions based on the electrode gap width and channel height. The deposition of long CNTs across ITO electrodes has potential use in transparent electronics and microfluidic systems.     

Nafion修饰玻碳电极吸附伏安法直接测定邻氨基苯酚

在 p H=2 .0的 0 .1 mol/ L H3 PO4 缓冲溶液中 ,开路搅拌富集 2 min后 ,从 0 .0 0～ +1 .0 0 V阳极扫描 ,OAP在 Nafion修饰玻碳电极上出现一灵敏的氧化峰 ,峰电位位于 0 .44 V。该峰电流与 OAP在 1× 1 0 - 7～ 2 .5× 1 0 - 5mol/ L的浓度范围内有良好的线性关系 ,检出限为 1× 1 0 - 8mol/ L。对支持电解质的种类及 p H值、Nafion的用量、富集电位及时间、以及扫描速度等进行了优化 ,提出了一种直接测定邻氨基苯酚的电化学方法。将此方法用于水样中邻氨基苯酚的测定 ,取得了满意的结果     

Solubilization of carbon nanotubes by Nafion toward the preparation of amperometric biosensors

The ability to solubilize single-wall and multiwall carbon nanotubes (CNT) in the presence of the perfluorinated polymer Nafion is described. Such use of Nafion as a solubilizing agent for CNT overcomes a major obstacle for creating CNT-based biosensing devices. Their association with Nafion does not impair the electrocatalytic properties of CNT. The resulting CNT/Nafion modified glassy-carbon electrodes exhibit a strong and stable electrocatalytic response toward hydrogen peroxide. The marked acceleration of the hydrogen peroxide redox process is very attractive for the operation of oxidase-based amperometric biosensors, as illustrated for the highly selective low-potential (-0.05 V vs Ag/AgCl) biosensing of glucose. These findings open the door for using CNT in a wide range of chemical sensors and nanoscale electronic devices.     

Application of PEDOT‐CNT Microelectrodes for Neurotransmitter Sensing

In this work, composite microelectrodes from poly(3,4‐ethylenedioxythiophene) (PEDOT) and carbon nanotubes (CNT) are characterized as electrochemical sensing material for neurotransmitters. Dopamine can be detected using square wave voltammetry at these microelectrodes. The CNTs improve the sensitivity by a factor of two. In addition, the selectivity towards dopamine in the presence of ascorbic acid and uric acid was examined. While both electrodes, PEDOT and PEDOT‐CNT are able to detect all measured concentrations of dopamine in the presence of uric acid, small concentrations of dopamine and ascorbic acid are only distinguishable at PEDOT‐CNT electrodes. Changing the pH has a strong influence on the selectivity. Moreover, it is possible to detect concentrations as low as 1 µM dopamine in complex cell culture medium. Finally, other catecholamines like serotonin, epinephrine, norepinephrine and L ‐dopa are also electrochemically detectable at PEDOT‐CNT microelectrodes.     

Carbon nanotube-based symbiotic coaxial nanocables with nanosilica and nanogold particles as labels for electrochemical immunoassay of carcinoembryonic antigen in biological fluids

A feasible and practicable amperometric immunoassay strategy for sensitive screening of carcinoembryonic antigen (CEA) in human serum was developed using carbon nanotube (CNT)-based symbiotic coaxial nanocables as labels. To construct such a nanocable, a thin layer of silica nanoparticles was coated on the CNT surface by sonication and sol-gel methods, and then colloidal gold nanoparticles were assembled on the amino-functionalized SiO₂/CNTs, which were used for the label of horseradish peroxidase-anti-CEA conjugates (HRP-anti-CEA-Au/SiO₂/CNT). In the presence of analyte CEA, the sandwich-type immunocomplex was formed on an anti-CEA/Au/thionine/Nafion-modified glassy carbon electrode by using HRP-anti-CEA-Au/SiO₂/CNTs as detection antibodies. To embody the advantages of the protocol, the analytical properties of variously modified electrodes were compared in detail on the basis of different nanolabels. Under optimal conditions, the cathodic peak currents of the electrochemical immunosensor were proportional to the logarithm of CEA concentration over the range from 0.01 to 12 ng mL⁻¹ in pH 5.5 HAc-NaAc containing 5 mM H₂O₂. At a signal-to-noise ratio of 3, the detection limit (LOD) is 5 pg mL⁻¹ CEA. Intra- and inter-assay coefficients of variation were below 9.5%. Meanwhile, the selectivity and stability of the immunosensor were acceptable. In addition, the technique was evaluated by spiking CEA standards in pH 7.4 PBS and with 35 clinical serum specimens, receiving excellent accordance with results from commercially available electrochemiluminescent enzyme-linked immunoassay.     

Functional groups modulate the sensitivity and electron transfer kinetics of neurochemicals at carbon nanotube modified microelectrodes

The surface properties of carbon-based electrodes are critically important for the detection of biomolecules and can modulate electrostatic interactions, adsorption and electrocatalysis. Carbon nanotube (CNT) modified electrodes have previously been shown to have increased oxidative sensitivity and reduced overpotential for catecholamine neurotransmitters, but the effect of surface functionalities on these properties has not been characterized. In this study, we modified carbon-fiber microelectrodes (CFMEs) with three differently functionalized single-wall carbon nanotubes and measured their response to serotonin, dopamine, and ascorbic acid using fast-scan cyclic voltammetry. Both carboxylic acid functionalized and amide functionalized CNTs increased the oxidative current of CFMEs by approximately 2-6 fold for the cationic neurotransmitters serotonin and dopamine, but octadecylamine functionalized CNTs resulted in no significant signal change. Similarly, electron transfer was faster for both amide and carboxylic acid functionalized CNT modified electrodes but slower for octadecylamine CNT modified electrodes. Oxidation of ascorbic acid was only increased with carboxylic acid functionalized CNTs although all CNT-modified electrodes showed a trend towards increased reversibility for ascorbic acid. Carboxylic acid-CNT modified disk electrodes were then tested for detection of serotonin in the ventral nerve cord of a Drosophila melanogaster larva, and the increase in sensitivity was maintained in biological tissue. The functional groups of CNTs therefore modulate the electrochemical properties, and the increase in sensitivity from CNT modification facilitates measurements in biological samples.     

Effects of pH on electrocatalytic activity of functionalized carbon nanotubes

In this study, we modified carbon nanotubes (CNTs) by grafting with poly(ethylene glycol) (PEG) using the “grafting to” method. The PEG-grafted CNT (CNT-g-PEG) was cast on indium tin oxide (ITO) electrode to investigate the electrocatalytic activity of CNT to the redox reactions of the Fe(CN)₆^3−/4−as a probe using cyclic voltammetry and electrochemical impedance spectroscopy. The electrocatalytic activity of CNT was correlated with CNT dispersion in the cast film on ITO as a function of pH of aqueous solution from which the film was cast. The CNT dispersions in aqueous solutions of different pH and in the cast films were examined by visual observation and zeta potential, scanning electron microscopy and transmission electron microscopy, respectively. At a pH in the range of 3–11 at which ITO electrode was modified, two functionalized CNT (fCNT and CNT-g-PEG) were both found to electrocatalyze the redox reactions of the Fe(CN)₆^3−/4−probe and the PEG grafts in CNT-g-PEG could help CNT adhere to the electrode to obtain durable modified electrode. The more uniform CNT dispersions in aqueous solutions and in the cast films appeared to have greater electrocatalytic acitivity.     

低热固相法制备纳米MnO2/CNT超电容复合电极的循环稳定性

为了改善纳米MnO2超级电容器电极的充放电循环稳定性,以Mn(OAc)2·4H2O、NH4HCO3和碳纳米管(CNT)为原料,采用低热固相反应得到前驱体,再经焙烧和酸处理,制备了一系列CNT含量不同的纳米MnO2/CNT复合电极材料,并用X射线衍射(XRD)、透射电镜(TEM)和Brunauer-Emmett-Teller(BET)比表面积测定方法对其进行了表征.XRD分析结果表明,复合材料中的MnO2为纳米γ-MnO2.研究了复合电极在1 mol·L-1 LiOH电解质中的电化学性能,并与不含CNT的纯纳米MnO2电极进行了比较.结果表明,含CNTs为10%(w,质最分数,下同)和20%的MnO2/CNT复合电极的循环稳定性远优于纯纳米MnO2电极的循环稳定性,其中含10%CNTs的MnO2/CNT复合电极不仪具有良好的循环稳定性,而且在1000 mA·g-1高倍率充放电条件下仍具有200 F·g-1的高比电容.     

Electroreduction of α-glucose on CNT/graphite electrode modified by Zn and Zn–Fe alloy

Electroreduction of -glucose to form sorbitol on Zn/CNTs and Zn alloy/CNTs electrodes has been investigated in this paper. Carbon nanotubes (CNTs) used in this paper are grown directly on graphite disks by chemical vapor deposition. Zn and Zn alloy are electrodeposited on the activated CNTs/graphite electrode by pulse galvanostatic method. The micrographs of Zn/CNTs and Zn alloy/CNTs electrodes are characterized by scanning electron microscopy. The results show that the current efficiency of -glucose reduction on CNTs electrodes is much better than that on flat Zn electrodes. The order of the current efficiency on different electrodes is as follows: Zn/CNT (0.58) Zn–Fe/CNT (0.57)>Zn–Ni/CNT (0.43) Zn/graphite (0.42)>Zn (0.40). It indicates that CNTs have good potential application in electrosynthesis. Additionally, effects of some operating parameters, such as pH, temperature and -glucose concentration, on the current efficiency of -glucose reduction are also discussed.     

Electrochemical oxidation behavior of methotrexate at DNA/SWCNT/Nafion composite film-modified glassy carbon electrode

Glassy carbon electrode modified with DNA-functionalized single-walled carbon nanotube (DNA/SWCNT) and Nafion composite film was developed for the detection of methotrexate. The characteristics of the modified electrode were examined by transmission electron microscopy and cyclic voltammetry. Compared with a bare glassy carbon electrode and Nafion- and SWCNT/Nafion-modified electrodes, the DNA/SWCNT/Nafion-modified one exhibited the more superior ability of detecting methotrexate, including the higher sensitivity and the lower overpotentials, due to the synergetic DNA-functionalized SWCNT and Nafion. Also, the dependence of the current on pH, nature of buffer, instrumental parameters, accumulation time, and potential was investigated to optimize the experimental conditions in the determination of methotrexate. Under the selected conditions, the modified electrode in pH?=?2.78 Britton–Robinson buffer solutions showed a linear voltammetric response to methotrexate within the concentration range of 2.0?×?10^?8–1.5?×?10^?6?mol?L^?1, with the detection limit of 8.0?×?10^?9?mol?L^?1. The method was also applied to detect methotrexate in medicinal tablets and spiked human blood serum samples.     

Morphology,rheological and crystallization behavior in non-covalently functionalized carbon nanotube reinforced poly(butylene succinate) nanocomposites with low percolation threshold

Multi-walled carbon nanotubes (CNTs) were non-covalently functionalized by surface wrapping of poly(sodium 4-styrenesulfonate) (PSS) with the aid of ultrasound. The functionalized CNTs were incorporated into poly(butylene succinate) (PBS) through solution coagulation to fabricate CNTs filled PBS nanocomposites. The morphologies of the PBS/CNT nanocomposites were studied by scanning electron microscope (SEM) and transmission electron microscope (TEM), and the effect of loading of functionalized CNT on the rheological behavior, electrical conductivity and mechanical properties of the nanocomposites was investigated systemically. SEM observation indicates that functionalized CNTs dispersed in PBS matrix without obvious aggregation and showed good interfacial adhesion with the PBS phase. TEM observation reveals that a CNT network was formed when the loading of CNTs increased from 0.1 to 0.3 wt%. Rheological investigation indicates the formation of a CNT network with a percolation threshold of only 0.3 wt%. Significant improvement in electrical conductivity occurred at CNT loading of 0.3 wt%, with the value of electrical conductivity increasing by six orders of magnitude compared to neat PBS. Differential scanning calorimetry indicates that the melt crystallization temperature of PBS was improved by ∼14 °C with addition of only 0.05 wt% functionalized CNTs. Tensile tests indicate that both the yield strength and Young's modulus of PBS were apparently reinforced by incorporation of functionalized CNTs, while the elongation at break was reduced gradually.     

An experimental investigation on the conductive behavior of carbon nanotube-reinforced natural polymer nanocomposites

It is well known that carbon nanotubes (CNTs) have excellent electrical properties and can be used as the nanofiller in natural polymers to produce conductive CNT/polymer nanocomposites. In this study, the conductive behavior of CNT-reinforced natural polymer nanocomposites was investigated. The effect of CNT concentration on the conductivity of CNT/natural polymer nanocomposites was also investigated. The natural polymers used were plasticized starch (PS) and chitosan (CS). FTIR spectroscopy was used to examine the interactions between PS, CS, and CNTs. TEM analysis on both nanocomposites were made to study the dispersion states of CNTs in both polymers. The results showed that the surface resistivities of both CNT/PS and CNT/CS nanocomposites decreased steeply with increasing CNT concentration. Particularly, the CNT/CS nanocomposites showed a better conductivity than the CNT/PS composites at the same CNT concentration. The TEM result showed that CNT/CS nanocomposites had better dispersibility and formation of fully connected, three-dimensional network structures between the CNTs than the CNT/PS nanocomposites, which results in the superior conductive property of CNT/CS nanocomposites compared to the CNT/PS nanocomposites.     

自支撑CNTs/SMF-Ni电极上电催化氧气氧化茴香醚合成茴香醛

以具有三维开放网络结构的薄层大面积烧结8 μm金属纤维(SMF-Ni, SMF-SS(316L不锈钢))为基底, 通过乙烯催化化学气相沉积在金属纤维表面生长碳纳米管(CNTs)的方法, 制备了整体式CNTs/SMF-Ni (CNTs: 50% (w))和CNTs/SMF-SS (CNTs: 40% (w))复合材料. 研究表明, 以CNTs/SMF-Ni 为阴极材料、SMF-SS为阳极材料, 具有很高的直接电催化氧气氧化对甲氧基甲苯(茴香醚)合成对甲氧基苯甲醛(茴香醛) 的活性, 反应物转化率和产物选择性分别达95.4%和96.5%, 电流效率可超过80%.     

Comparative study of the electrochemical behavior and analytical applications of (bio)sensing platforms based on the use of multi-walled carbon nanotubes dispersed in different polymers

This review present a critical comparison of the electrochemical behavior and analytical performance of glassy carbon electrodes (GCE) modified with carbon nanotubes (CNTs) dispersed in different polymers: polyethylenimine (PEI), PEI functionalized with dopamine (PEI-Do), polyhistidine (Polyhis), polylysine (Polylys), glucose oxidase (GOx) and double stranded calf-thymus DNA (dsDNA). The comparison is focused on the analysis of the influence of the sonication time, solvent, polymer/CNT ratio, and nature of the polymer on the efficiency of the dispersions and on the electrochemical behavior of the resulting modified electrodes. The results allow to conclude that an adequate selection of the polymers makes possible not only an efficient dispersion of CNTs but also, and even more important, the building of successful analytical platforms for the detection of different bioanalytes like NADH, glucose, DNA and dopamine.