Simultaneous determination of salbutamol sulphate, bromhexine hydrochloride and etofylline in pharmaceutical formulations with the use of four rapid derivative spectrophotometric methods

Four simple, rapid, accurate, precise, reliable and economical spectrophotometric methods have been proposed for simultaneous determination of salbutamol sulphate (SS), bromhexine hydrochloride (BH) and etofylline (ET) in pure and commercial formulations without any prior separation or purification. They were first derivative zero crossing spectrophotometry (method 1), simultaneous equation method (method 2), derivative ratio spectra zero crossing method (method 3) and double divisor ratio spectra derivative method (method 4). The ranges for SS, BH and ET were found to be 1-35 μg mL⁻¹, 4-40 μg mL⁻¹ and 5-80 μg mL⁻¹. For methods 1 and 2, the values of limit of detection (LOD) were 0.2314 μg mL⁻¹, 0.4865 μg mL⁻¹ and 0.2766 μg mL⁻¹ and the values of limit of quantitation (LOQ) were 0.7712 μg mL⁻¹, 1.6217 μg mL⁻¹ and 0.9221 μg mL⁻¹ for SS, BH and ET, respectively. For method 3, LOD values were 0.3297 μg mL⁻¹, 0.2784 μg mL⁻¹ and 0.7906 μg mL⁻¹ and LOQ values were 0.9325 μg mL⁻¹, 0.9282 μg mL⁻¹ and 2.6352 μg mL⁻¹ for SS, BH and ET, respectively. For method 4, LOD values were 0.3161 μg mL⁻¹, 0.2495 μg mL⁻¹ and 0.2064 μg mL⁻¹ and LOQ values were 0.9869 μg mL⁻¹, 0.8317 μg mL⁻¹ and 0.6879 μg mL⁻¹ for SS, BH and ET. The precision values were less then 2% R.S.D. for all four methods. The common excipients and additives did not interfere in their determinations. The results obtained by the proposed methods have been statistically compared by means of Student t-test and by the variance ratio F-test.     

Improved porous silicon microarray based prostate specific antigen immunoassay by optimized surface density of the capture antibody

Enriching the surface density of immobilized capture antibodies enhances the detection signal of antibody sandwich microarrays. In this study, we improved the detection sensitivity of our previously developed P-Si (porous silicon) antibody microarray by optimizing concentrations of the capturing antibody. We investigated immunoassays using a P-Si microarray at three different capture antibody (PSA – prostate specific antigen) concentrations, analyzing the influence of the antibody density on the assay detection sensitivity. The LOD (limit of detection) for PSA was 2.5 ng mL⁻¹, 80 pg mL⁻¹, and 800 fg mL⁻¹ when arraying the PSA antibody, H117 at the concentration 15 μg mL⁻¹, 35 μg mL⁻¹, and 154 μg mL⁻¹, respectively. We further investigated PSA spiked into human female serum in the range of 800 fg mL⁻¹ to 500 ng mL⁻¹. The microarray showed a LOD of 800 fg mL⁻¹ and a dynamic range of 800 fg mL⁻¹ to 80 ng mL⁻¹ in serum spiked samples.     

Development of a validated liquid chromatographic method for the quality control of Prunellae Spica: Determination of triterpenic acids

A simple and rapid reversed-phase HPLC-UV method was developed for the determination of triterpenic acids in the crude extract of Prunellae Spica. Five triterpenic acids were extracted and isolated from P. Spica as marker compounds for use in the quality control of herbal medicines. Various solvent extraction techniques were evaluated, and the greatest efficiency was observed with sonication in 100% ethanol. Elemental compositions of the five marker compounds were determined by high-resolution mass spectroscopy. The dynamic range of the HPLC-UV method depended on the specific analyte, and acceptable quantitation was obtained between 10 and 250 μg mL⁻¹ for oleanolic acid, between 10 and 300 μg mL⁻¹ for ursolic acid, between 3 and 75 μg mL⁻¹ for 2α,3α,24-trihydroxyolean-12en-28oic acid, between 5 and 100 μg mL⁻¹ for euscaphic acid, and between 5 and 100 μg mL⁻¹ for 2α,3α-dihydroxyurs-12en-28oic acid. The method was deemed satisfactory by inter- and intra-day validation and exhibited both high accuracy and precision (relative standard deviation <9.4%). Overall limits of quantitation and detection were approximately 0.5-2.5 μg mL⁻¹ at a signal-to-noise ratio (S/N) of 3 and were about 3.0-10.0 μg mL⁻¹ at a S/N of 10. In addition, principal component analysis (PCA) was performed on the analytical data of 15 different P. Spica samples in order to classify samples collected from different regions.     

Chromogenic platform based on recombinant Drosophila melanogaster acetylcholinesterase for visible unidirectional assay of organophosphate and carbamate insecticide residues

In this study we propose a chromogenic platform for rapid analysis of organophosphate (OP) and carbamate (CM) insecticide residues, based on recombinant Drosophila melanogaster acetylcholinesterase (R-DmAChE) as enzyme and indoxyl acetate as substrate. The visible chromogenic strip had the advantages identical to those of commonly used lateral flow assays (LFAs) with utmost simplicity in sample loading and result observation. After optimization, depending on the color intensity (CI) values, the well-established assay has the capabilities of both qualitative measurement via naked eyes and quantitative analysis by colorimetric reader with the desirable IC₅₀ values against the tested six insecticides (0.06 μg mL⁻¹ of carbofuran, 0.28 μg mL⁻¹ of methomyl, 0.03 μg mL⁻¹ of dichlorvos, 31.6 μg mL⁻¹ of methamidophos, 2.0 μg mL⁻¹ of monocrotophos, 6.3 μg mL⁻¹ of omethoate). Acceptable matrix effects and satisfactory detection performance were confirmed by in-parallel LC–MS/MS analysis in different vegetable varieties at various spiked levels of 10⁻³ to 10¹ μg g⁻¹. Overall, the testified suitability and applicability of this novel platform meet the requirements for practical use in food safety management and environmental monitoring, especially in the developing world.     

A sensitive sensor for anthraquinone anticancer drugs and hsDNA based on CdTe/CdS quantum dots fluorescence reversible control

Based on CdTe/CdS quantum dots (CdTe/CdS QDs) fluorescence (FL) reversible control, a new and sensitive FL sensor for determination of anthraquinone (AQ) anticancer drugs (adriamycin and daunorubicin) and herring sperm DNA (hsDNA) was developed. Under the experimental conditions, FL of CdTe/CdS QDs can be effectively quenched by AQ anticancer drugs due to the binding of AQ anticancer drugs on the surface of CdTe/CdS QDs and photoinduced electron transfer (PET) process from CdTe/CdS QDs to AQ anticancer drugs. Addition of hsDNA afterwards brought the restoration of CdTe/CdS QDs FL intensity, as AQ anticancer drugs peeled off from the surface of CdTe/CdS QDs and embedded into hsDNA double helix structure. The liner ranges and the detection limits of FL quenching methods for two AQ anticancer drugs were 0.33-9 μg mL⁻¹ and 0.09 μg mL⁻¹ for ADM and 0.15-9 μg mL⁻¹ and 0.04 μg mL⁻¹ for DNR, respectively. The restored FL intensity was proportional to concentration of hsDNA in the range of 1.38-28 μg mL⁻¹and the detection limit for hsDNA was 0.41 μg mL⁻¹. It was applied to the determination of AQ anticancer drugs in human serum and urine samples with satisfactory results. The reaction mechanism of CdTe/CdS QDs FL reversible control was studied.     

Separation and determination of benzene, toluene, ethylbenzene and o-xylene compounds in water using directly suspended droplet microextraction coupled with gas chromatography-flame ionization detector

The directly suspended droplet microextraction (DSDME) technique coupled with the capillary gas chromatography-flame ionization detector (GC-FID) was used to determine BTEX compounds in aqueous samples. The effective parameters such as organic solvent, extraction time, microdroplet volume, salt effect and stirring speed were optimized. The performance of the proposed technique was evaluated for the determination of BTEX compounds in natural water samples. Under the optimal conditions the enrichment factors ranged from 142.68 to 312.13, linear range; 0.01-20 μg mL⁻¹, limits of detection; 0.8-7 ng mL⁻¹ for most analytes. Relative standard deviations for 0.2 μg mL⁻¹ of BTEX in water were in the range 1.81-2.47% (n = 5). The relative recoveries of BTEX from surface water at spiking level of 0.2 μg mL⁻¹ were in the range of 89.87-98.62%.     

Cobalt phthalocyanine as a novel molecular recognition reagent for batch and flow injection potentiometric and spectrophotometric determination of anionic surfactants

Cobalt(II) phthalocyanine [Co(II)Pc] is used as both an ionophore and chromogen for batch and flow injection potentiometric and spectrophotometric determination of anionic surfactants (SDS), respectively. The potentiometric technique involves preparation of a polymeric membrane sensor by dispersing [Co(II)Pc] in a plasticized PVC membrane. Under batch mode of operation, the sensor displays a near-Nernstian slope of −56.5 mV decade⁻¹, wide response linear range of 7.8 × 10⁻⁴ to 8.0 × 10⁻⁷ mol L⁻¹, lower detection limit of 2.5 × 10⁻⁷ mol L⁻¹ and exhibits high selectivity for anionic surfactants in the presence of many common ions. Under hydrodynamic mode of operation (FIA), the slope of the calibration plot, limit of detection, and working linear range are −51.1 mV decade⁻¹, 5.6 × 10⁻⁷ and 1.0 × 10⁻³ to 1.0 × 10⁻⁶ mol L⁻¹, respectively. The spectrophotometric method is based on the use of [Co(II)Pc] solution in dimethylsulfoxide (DMSO) as a chromogenic reagent. The maximum absorption of the reagent at 658 nm linearly decreases with the increase of anionic surfactant over the concentration range 2-30 μg mL⁻¹. The lower limit of detection is 1 μg mL⁻¹ and high concentrations of many interfering ions are tolerated. Flow injection spectrophotometric measurements are carried out by injection of the surfactant test solution in a stream of the reagent in DMSO. The sample throughput, working range and lower detection limit are 25-30 samples h⁻¹, 4-60 and 2 μg mL⁻¹, respectively. The potentiometric and spectrophotometric techniques are applied to the batch and flow injection measurements of anionic surfactants in some commercial detergent products. The results agree fairly well with data obtained using the standard methylene blue spectrophotometric method.     

A rapid, acetonitrile-free, HPLC method for determination of melamine in infant formula

A simple, precise, accurate and validated, acetonitrile-free, reverse phase high performance liquid chromatography (HPLC) method is developed for the determination of melamine in dry and liquid infant formula. The separation is performed on a Kromasil C18 column (150 mm × 3.2 mm I.D., 5 μm particle size) at room temperature. The mobile phase (0.1% TFA/methanol 90:10) is pumped at a flow rate of 0.3 mL min⁻¹ with detection at 240 nm. Melamine elutes at 3.7 min. A linear response (r > 0.999) is observed for samples ranging from 1.0 to 80 μg mL⁻¹. The method provides recoveries of 97.2-101.2% in the concentration range of 5-40 μg mL⁻¹, intra- and inter-day variation in <1.0% R.S.D. The limit of detection (LOD) and limit of quantification (LOQ) values are 0.1 μg mL⁻¹ and 0.2 μg mL⁻¹, respectively.     

On-line continuous flow ultrasonic extraction coupled with high performance liquid chromatographic separation for determination of the flavonoids from root of Scutellaria baicalensis Georgi

An on-line method, based on coupling dynamic ultrasonic extraction (DUE), continuously sampling the suspension of sample and solvent, high performance liquid chromatographic separation with diode array detection, has been developed for the determination of the flavonoids, including baicalin, baicalein and wogonin, from the root of Scutellaria baicalensis Georgi. Variables influencing the DUE were evaluated by orthogonal test. The extraction yields of baicalin, baicalein and wogonin in the roots of S. baicalensis Georgi obtained from five different cultivated areas are 73.8–131.5 μg mg⁻¹ (RSD ≤ 6.24%), 6.8–15.9 μg mg⁻¹ (RSD ≤ 5.36%) and 4.4–14.3 μg mg⁻¹ (RSD ≤ 5.30%), respectively. The limits of detection for baicalin, baicalein and wogonin are 0.30, 0.37 and 0.41 μg mL⁻¹, respectively. Linearity is from 0.55 to 109 μg mL⁻¹ for baicalin, from 0.51 to 105 μg mL⁻¹ for baicalein and from 0.53 to 102 μg mL⁻¹ for wogonin. Compared with off-line continuous flow-DUE, the proposed method would be more convenient for the determination of the analytes and the rapid optimization of the extraction process. The extraction yields of flavonoids obtained by the proposed method are comparable with those obtained by dynamic microwave assisted extraction, static ultrasonic extraction and reflux extraction. The result indicated that the proposed method is suitable to determine the active components in Chinese herbal medicine.     

High extraction efficiency for polar aromatic compounds in natural water samples using multiwalled carbon nanotubes/Nafion solid-phase microextraction coating

A novel solid-phase microextraction (SPME) fiber coated with multiwalled carbon nanotubes (MWCNTs)/Nafion was developed and applied for the extraction of polar aromatic compounds (PACs) in natural water samples. The characteristics and the application of this fiber were investigated. Electron microscope photographs indicated that the MWCNTs/Nafion coating with average thickness of 12.5 μm was homogeneous and porous. The MWCNTs/Nafion coated fiber exhibited higher extraction efficiency towards polar aromatic compounds compared to an 85 μm commercial PA fiber. SPME experimental conditions, such as fiber coating, extraction time, stirring rate, desorption temperature and desorption time, were optimized in order to improve the extraction efficiency. The calibration curves were linear from 0.01 to 10 μg mL⁻¹ for five PACs studied except p-nitroaniline (from 0.005 to 10 μg mL⁻¹) and m-cresol (from 0.001 to 10 μg mL⁻¹), and detection limits were within the range of 0.03–0.57 ng mL⁻¹. Single fiber and fiber-to-fiber reproducibility were less than 7.5 (n = 7) and 10.0% (n = 5), respectively. The recovery of the PACs spiked in natural water samples at 1 μg mL⁻¹ ranged from 83.3 to 106.0%.     

Facile, sensitive and selective fluorescence turn-on detection of HSA/BSA in aqueous solution utilizing 2,4-dihydroxyl-3-iodo salicylaldehyde azine

A novel fluorescence turn-on detection method of human serum albumin (HSA) and bovine serum albumin (BSA) in aqueous solution is investigated using 2,4-dihydroxyl-3-iodo salicylaldehyde azine (DISA). Upon the addition of DISA to HSA/BSA solution, a fluorescence turn-on effect at 529 nm can be observed with a large stokes shift of ∼129 nm based on hydrophobic binding-mode between protein and dye. Under the optimal condition, the linear ranges of fluorescence intensity for HSA and BSA are 0.1-30 μg mL⁻¹ with the relative correlation coefficient of R² = 0.991 (n = 10) and 0.3-50 μg mL⁻¹ with R² = 0.997 (n = 10); and the detection limits for HSA and BSA based on IUPAC (C_DL = 3S_b/m) are 20 ng mL⁻¹ and 50 ng mL⁻¹, respectively.     

Three-way models and detection capability of a gas chromatography-mass spectrometry method for the determination of clenbuterol in several biological matrices: the 2002/657/EC European Decision

Clenbuterol has been extracted by mixed solid-phase extraction from two biological matrices (bovine hair and urine) and detected by GC/MS (selected ion monitoring (SIM) and full-SCAN modes). The analytical signal has been modelled with univariate and three-way models, namely DTLD, PARAFAC, PARAFAC2, Tucker3 and trilinear PLS. Since clenbuterol is a banned substance a comparative study of the capability of detection (CCβ, X₀=0) has been performed as a function of the sample (hair, 74 μg kg⁻¹ and urine, 0.36 μg l⁻¹), the mode in which the signals are monitored (SCAN, 283 μg kg⁻¹ and SIM, 74 μg kg⁻¹) and the statistical model (univariate, 283 μg kg⁻¹ and trilinear PLS, 20.91 μg kg⁻¹). The capability of detection has been calculated as stated in ISO 11843 and Decision 2002/657/EC setting in all cases the probabilities of false positive and of false negative at 0.05.The identification of the mass spectra must be done to confirm the presence of clenbuterol and has been carried out through PARAFAC. The correlation coefficient between the spectra estimated by PARAFAC and the library spectra is 0.96 (hair, SCAN mode) and 1.00 (hair and urine, SIM mode).The Decision 2002/657/EC advocates the use of independent mass fragments to identify banned compounds. These recommendations together with the effect of the number of ions registered on the capability of detection have lead us to select five uncorrelated fragments (86, 243, 262, 264 and 277) from the data set of 210 ions by hierarchical clustering of variables.     

Fluorescence enhancement of CdTe/CdS quantum dots by coupling of glyphosate and its application for sensitive detection of copper ion

A novel fluorescent probe for Cu²⁺ determination based on the fluorescence quenching of glyphosate (Glyp)-functionalized quantum dots (QDs) was firstly reported. Glyp had been used to modify the surface of QDs to form Glyp-functionalized QDs following the capping of thioglycolic acid on the core–shell CdTe/CdS QDs. Under the optimal conditions, the response was linearly proportional to the concentration of Cu²⁺ between 2.4 × 10⁻² μg mL⁻¹ and 28 μg mL⁻¹, with a detection limit of 1.3 × 10⁻³ μg mL⁻¹ (3δ). The Glyp-functionalized QDs fluorescent probe offers good sensitivity and selectivity for detecting Cu²⁺. The fluorescent probe was successfully used for the determination of Cu²⁺ in environmental samples. The mechanism of reaction was also discussed.     

Study on the resonance Rayleigh scattering spectra of the interactions of palladium (II)-cephalosporins chelates with 4,5-dibromofluorescein and their analytical applications

In pH 2.8-3.8 BR buffer medium, the third generation cephalosporin antibiotics (TGCs) such as ceftazidime (CZD), ceftriaxone (CTRX), cefoperazone (CPZ), and cefotaxime (CFTM) react with palladium(II) (Pd(II)) to form 1:2 yellowish-brown cationic chelates, which further react with 4, 5-dibromofluorescein (DBF) to form 1:3 brown ion-association complexes. As a result, not only the spectra of absorption and fluorescence are changed, but also the resonance Rayleigh scattering (RRS) is enhanced greatly and the new RRS spectra are observed. The four TGCs products have similar spectral characteristics and their maximum RRS wavelengths are all located at 291 nm. The quantitative determination ranges and the detection limits of the four TGCs are 0.0065-1.0 μg mL⁻¹ and 2.0 ng mL⁻¹ for CZD, 0.0070-1.1 μg mL⁻¹ and 2.2 ng mL⁻¹ for CTRX, 0.0090-1.6 μg mL⁻¹ and 2.7 ng mL⁻¹ for CPZ, and 0.014-2.2 μg mL⁻¹ and 4.2 ng mL⁻¹ for CFTM, respectively. The optimum conditions of the reactions and the effects of foreign substances are investigated, and the composition of ion-association complexes is discussed also. Based on the ion-association reaction, a highly sensitive, simple and rapid method has been proposed to the determination of TGCs.     

Screening and determination of melamine residues in tissue and body fluid samples

Melamine is a chemical product that was sporadically mixed into animal feeds to boost protein content. Excessive melamine in animal feed can induce renal failure and even death in animals. The residue of melamine in edible animal products also threatens human health. Currently, there is no real-time and high throughput method to detect residual melamine in animal tissues. Successful development of such methods is very important for fast and on-site screening of melamine residue in animal tissues to eliminate the potential threat to human health. Here we demonstrate the detection of residual melamine from swine and chicken tissues and body fluids using indirect competitive enzyme-linked immunosorbent assay (ELISA) method. A detection sensitivity of 0.5 μg mL⁻¹ and a limit of detection of 0.05 μg mL⁻¹ were achieved with this method. A gas chromatography-mass spectrometry (GC-MS) method was also developed to act as a confirmatory and quantitative procedure for the ELISA results. The limits of quantitation (LOQ) of were 0.01 μg g⁻¹ and 0.005 μg mL⁻¹ for tissues and body fluids, respectively. The two methods showed good agreement (r² > 0.992). The method developed was performed on samples of tissues from chickens fed with melamine-spiked feed.     

A reversed-phase high performance liquid chromatography coupled with resonance Rayleigh scattering detection for the determination of four tetracycline antibiotics

A new reversed-phase high performance liquid chromatography with resonance Rayleigh scattering detection (HPLC-RRS) was developed for simultaneous separation and determination of four tetracycline antibiotics (TCs). A good chromatographic separation among the compounds was achieved using a Synergi Fusion-RP column (150 mm × 4.6 mm; 4 μm) and a mobile phase consisting of methanol-acetonitrile-oxalic acid (5 mM) at the flow rate of 0.8 mL min⁻¹. Column temperature was 30 °C. The RRS signal was detected at λ_ex = λ_em = 370 nm. The recoveries of sample added standard ranged from 95.3% to 103.5%, and the relative standard deviation was below 2.79%. A detection limit of 2.12-5.12 μg mL⁻¹ was reached and a linear range was found between peak height and concentration in the range of 10.36-518.0 μg mL⁻¹ for oxytetracycline (OTC), 12.11-605.5 μg mL⁻¹ for tetracycline (TC), 11.79-589.5 μg mL⁻¹ for chlortetracycline (CTC) and 10.32-516.0 μg mL⁻¹ for doxycycline (DC). The linear regression coefficients were all above 0.999. The method has been applied successfully to the determination of OTC, TC, CTC, DC in pharmaceutical formulations and in honey. The method was simple, rapid and showed a better linear relation and high repeatability.     

Determination of beta-lactam antibiotics in milk using micro-flow chemiluminescence system with on-line solid phase extraction

In this paper, a chemiluminescence (CL) micro-flow system combined with on-line solid phase extraction (SPE) is presented for determination of β-lactam antibiotics (penicillin, cefradine, cefadroxil, cefalexin) in milk. It is based on the enhancement effect of β-lactam antibiotics on the luminol-K₃Fe(CN)₆ CL system. The micro-flow system was fabricated from two polymethyl methacrylate (PMMA) plates (50 mm × 40 mm × 5 mm) with the microchannels of 200 μm wide and 150 μm deep. C₁₈-modified silica gel was packed into the microchannel (length: 10 mm; width: 1 mm; depth: 500 μm) to serve as SPE device. Extraction and preconcentration of the analytes were carried out using on-line SPE micro-flow system and the selectivity of CL detection was improved. The detection limits were 0.5 μg mL⁻¹ of penicillin, 0.04 μg mL⁻¹ of cefradine, 0.08 μg mL⁻¹ of cefadroxil and 0.1 μg mL⁻¹ of cefalexin. The proposed method was also applied to analyze the β-lactam antibiotics in milk. Experimental results were in good agreement with those obtained by high performance liquid chromatography (HPLC) method with UV detection.     

A novel microchip based on indium tin oxide coated glass for contactless conductivity detection

A microfluidic chip manufactured from glass substrate and indium tin oxide (ITO) coated glass use for contactless conductivity detection was developed. The detecting electrodes were fabricated by screen-printing and chemical etching methods using an ITO-coated glass wafer. Then, the glass substrate containing separation channels was bonded with the bare side of the processed ITO-coated glass, thus producing an electrophoresis chip integrated with contactless conductivity detector. The prepared microchip displayed considerable stability and reproducibility. Sensitive response was obtained at optimal conditions (including the gap between electrodes, excitation frequency, and excitation voltage). The feasibility of this microfluidic device was examined by detection of inorganic ions, and further demonstrated by the quantification of aminopyrine and caffeine in a compound pharmaceutical. The two ingredients can be completely separated within 1 min. The detection limits were 8 μg mL⁻¹ and 3 μg mL⁻¹, respectively; with the correlation coefficient of 0.996-0.998 in the linear range from 10 μg mL⁻¹ to 800 μg mL⁻¹. The results have showed that the present method is sensitive, reliable and fast.     

Electropolymerized multiwalled carbon nanotubes/polypyrrole fiber for solid-phase microextraction and its applications in the determination of pyrethroids

A novel solid-phase microextraction (SPME) fiber coated with multiwalled carbon nanotubes/polypyrrole (MWCNTs/Ppy) was prepared with an electrochemical method and used for the extraction of pyrethroids in natural water samples. The results showed that the MWCNTs/Ppy coated fiber had high organic stability, and remarkable acid and alkali resistance. In addition, the MWCNTs/Ppy coated fiber was more effective and superior to commercial PDMS and PDMS/DVD fibers in extracting pyrethroids in natural water samples. Under optimized conditions, the calibration curves were found to be linear from 0.001 to 10 μg mL⁻¹ for five of the six pyrethroids studied, the exception being fenvalerate (which was from 0.005 to 10 μg mL⁻¹), and detection limits were within the range 0.12-0.43 ng mL⁻¹. The recoveries of the pyrethroids spiked in water samples at 10 ng mL⁻¹ ranged from 83 to 112%.     

Determination of non-ionic and anionic surfactants in environmental water matrices

Solid-phase extraction (SPE) combined with liquid chromatography electrospray mass spectrometry (LC-(ESI)MS) was used to determine 16 non-ionic and anionic surfactants in different environmental water samples at ng L⁻¹ levels. The proposed method is sensitive and simple and has good linear range and detection limits (less than 50 ng L⁻¹) for most compound classes.The effect of ion suppression was studied in aqueous matrices from several treatment plants—including urban and industrial wastewater treatment plants (WWTPs), drinking-water treatment plants (DWTPs) and seawater desalination plants (SWDPs)—and it was considered when quantifying our samples. In addition, conventional treatments and tertiary treatments that use advanced membrane technologies, such as ultrafiltration (UF) and reverse osmosis (RO) were evaluated in order to determine their efficiency in eliminating these compounds.The concentrations of non-ionic surfactants in the raw waters studied ranged from 0.2 to 100 μg L⁻¹. In effluents, the concentrations ranged from 0.1 to 5 μg L⁻¹, which reflects consistent elimination. Anionic surfactants were present in all waters studied at higher levels. Levels up to 3900 μg L⁻¹ of linear alkylbenzene sulfonates (LASs) and 32,000 μg L⁻¹ of alkyl ethoxysulfates (AESs) were detected in urban WWTP influents, while levels up to 25 μg L⁻¹ of LASs and 114 μg L⁻¹ of AESs were found in drinking-water and desalination treatment plants.The results indicate that conventional processes alone are not sufficient to completely remove the studied surfactants from waste streams. Tertiary treatments that use advanced membrane technologies such as UF and RO can further reduce the amount of target compounds in the effluent water.