A novel super-FEC code based on concatenated code for high-speed long-haul optical communication systems

The structures of the novel super forward error correction (Super-FEC) code type based on the concatenated code for high-speed long-haul optical communication systems are studied in this paper. The Reed-Solomon (RS) (255, 239) + Bose-Chaudhuri-Hocguenghem (BCH) (1023, 963) concatenated code is presented after the characteristics of the concatenated code and the two Super-FEC code type presented in ITU-T G.975.1 have theoretically been analyzed, the simulation result shows that this novel code type, compared with the RS (255, 239) + convolutional-self-orthogonal-code (CSOC) (k₀/n₀ = 6/7, J = 8) code in ITU-T G.975.1, has a lower redundancy and better error-correction capabilities, and its net coding gain (NCG) at the third iteration is 0.57 dB more than that of RS (255, 239) + CSOC (k₀/n₀ = 6/7, J = 8) code in ITU-T G.975.1 at the third iteration for the bit error rate (BER) of 10⁻¹². Therefore, the novel code type can better be used in long-haul, larger capacity and higher bit-rate optical communication systems. Furthermore, the design and implementation of the novel concatenated code type are also discussed.     

Non-steady-state photo-EMF in nanostructured GaN and polypyrrole within porous matrices

We report an experimental investigation of the non-steady-state photoelectromotive force in nanostructured GaN within porous glass and polypyrrole within chrysotile asbestos. The samples are illuminated by an oscillating interference pattern created by two coherent light beams and the alternating current is detected as a response of the material. Dependences of the signal amplitude versus temporal and spatial frequencies, light intensity, and temperature are studied for two wavelengths λ=442 and 532 nm. The conductivity of the GaN composite is measured: σ=(1.1–1.6)×10⁻¹⁰ Ω⁻¹ cm⁻¹ (λ=442 nm, I ₀=0.045–0.19 W/cm², T=293 K) and σ=(3.5–4.6)×10⁻¹⁰ Ω⁻¹ cm⁻¹ (λ=532 nm, I ₀=2.3 W/cm², T=249–388 K). The diffusion length of photocarriers in polypyrrole nanowires is also estimated: L _D=0.18 μm.     

Performance enhancement of the power penalty in DWDM FSO communication using DPPM and OOK modulation

This paper presents the design and performance enhancement of the power penalty (PP) in a dense wavelength division multiplexing based on free space optical communication (FSOC) link using digital pulse position modulation (DPPM) and on–off keying (OOK) modulation. Such a system has a high performance, low cost, robust and power efficient, reliable, excessive flexibility, and higher data rate for access networks. The system performance is evaluated for an 8-channel wavelength-division-multiplexing for hybrid fiber FSOC system at 2.5 Gbps on widely accepted modulation schemes under various atmospheric turbulence (AT) regimes conditions. The performance of system is introduced in terms of PP, bit-error rate (BER), transmission distance and the average received optical power. The numerical results shows that the improvement of the PP using DPPM modulation of 0.2–3.0 dB for weak turbulence (WT) regimes for BER of 10^?6 and above 20, 25 dB for strong turbulence (ST) regimes are reported for BER of 10^?6 and 10^?9, as respectively (depending on the AT level). Further, we develop of improvement the PP caused by multiple-access interference about 6.686 dB which is predicted for target BER of 10^?9 in WT and 1 dB at target BER of 10^?6 in ST when the 8 user are active on the system of optical network units. Additionally, the optical power budget and margin losses of a system are calculated with different link length. The proposed approach of DPPM merges superiority with higher enhancement of PP about 0.8 dB for BER equal 10^?9 at FSO link length l_fso?=?2000 m compared to OOK at 1 dB for WT. An improvement of 2 dB is observed using the DPPM scheme over an OOK due to capability of detect pulses under background noise conditions with increased receiver sensitivity.     

Electrical transport study of potato starch-based electrolyte system

A biopolymer electrolyte system having conductivity ∼1.3 × 10⁻⁴ S cm⁻¹ has been prepared using potato starch, NaI, glutaraldehyde and poly(ethylene glycol) (PEG; molecular weight = 300). High ionic transference numbers (∼0.99) of the material confirmed its electrolytic behaviour. Conductivity and dielectric behaviour as a function of frequency has been studied. Conductivity follows ‘universal power law’ (σ = σ ₀ + Aω ⁿ ) with exponent ‘n’ varying from 0.94 to 1.18. Cross-linking and plasticization increases long pathways motion of charge carriers, comparable to sample dimension. Humidity-independent behaviour (up to 80% relative humidity), of impedance and water intake by the system, indicates the system’s potentiality as a promising candidate for humidity immune device fabrication. The addition of PEG has a twofold effect on the material’s conductivity. It not only increases conductivity but also improves the material’s immunity towards humid atmosphere.     

Growth,spectroscopic and laser properties of Yb<Superscript>3<Emphasis Type="Bold">+</Emphasis></Superscript>-doped GdAl<Subscript>3</Subscript>(BO<Subscript>3</Subscript>)<Subscript>4</Subscript> crystal: a candidate for infrared laser crystal

Yb³⁺:GdAl₃(BO₃)₄ (hereafter Yb³⁺:GAB) crystals with large sizes and good optical quality have been grown by the top-seed solution growth (TSSG) method. The polarized absorption and emission spectra have been investigated at room temperature. For the σ-polarization, the intensities of both absorption and emission spectra are stronger than those for the π-polarization, the σ-absorption cross section of Yb³⁺ in GAB being 3.43×10^-20 cm² at 977 nm, and the σ-emission cross section being 0.98×10^-20 cm² at 1045 nm. The fluorescence lifetime of the ² F _5/2→² F _7/2 transition was measured to be 800 μs in the 5% doped sample used for our laser experiments, 993 μs in a 10% doped sample and 569 μs in a 0.5% doped sample. The laser parameters were estimated as: β_min=0.022, I_sat=10.4 kW/cm² and I_min=0.23 kW/cm². About 0.4 W laseroutput at the wavelength of 1043 nm was achieved when the Yb³⁺:GAB crystal was pumped by a 974 nm laser diode, with 27.4% slope efficiency. PACS 42.55.-f; 42.70.Hj; 78.20.-e; 81.10.Dn     

Electrical relaxation in proton conductor composites based on (NH4)H2PO4/TiO2

We report on electrical relaxation measurements of (1 − x)NH₄H₂PO₄-xTiO₂ (x = 0.1) composites by admittance spectroscopy, in the 40-Hz–5-MHz frequency range and at temperatures between 303 and 563 K. Simultaneous thermal and electrical measurements on the composites identify a stable crystalline phase between 373 and 463 K. The real part of the conductivity, σ’, shows a power-law frequency dependence below 523 K, which is well described by Jonscher’s expression , where σ ₀ is the dc conductivity, ω _p /2π = f _p is a characteristic relaxation frequency, and n is a fractional exponent between 0 and 1. Both σ ₀ and f _p are thermally activated with nearly the same activation energy in the II region, indicating that the dispersive conductivity originates from the migration of protons. However, activation energies decrease from 0.55 to 0.35 eV and n increases toward 1.0, as the concentration of TiO₂ nanoparticles increases, thus, enhancing cooperative correlation among moving ions. The highest dc conductivity is obtained for the composite x = 0.05 concentration, with values above room temperature about three orders of magnitude higher than that of crystalline NH₄H₂PO₄ (ADP), reaching values on the order of 0.1 (Ω cm)^− 1 above 543 K.     

PEO electrolytes containing dioctyl phthalate (DOP) for dye-sensitized nanocrystalline TiO2 solar cells

In this paper, we aim to prepare polymer electrolytes consisting of NaI and I₂ dissolved in poly(ethylene oxide) (PEO) and dioctyl phthalate (DOP) as an additive and apply the electrolytes to dye-sensitized solar cells (DSSC). Upon the incorporation of salt, the phthalic-stretching C=O bands of DOP in Fourier transform infrared spectra shifted to a lower wave number (Δf = 93 cm⁻¹), confirming the unusual strong complex formation between sodium ions and phthalic oxygen. Coordinative interactions and structural changes of PEO/NaI/I₂/DOP electrolytes have also been characterized by wide angle X-ray scattering, presenting an almost amorphous structure of the polymer electrolytes. The ionic conductivity of the polymer electrolytes reached ∼10^–4 S/cm at room temperature at the mole ratio of [EO]:[Na]:[DOP] = 10:1:0.5, as determined by the four-probe method. DSSC using the polymer electrolytes and conductive indium tin oxide glasses exhibited 2.9% of overall energy conversion efficiency (=P _max/P _in × 100) at one sun condition (100 mW/cm²). The good interfacial contact between the electrolytes and the dye-attached nanocrystalline TiO₂ layers were verified by field-emission scanning electron microscopy.     

Optical Flow-Through Sensor for the Determination of Norfloxacin Based on Emission of KMnO<Subscript>4</Subscript>–Na<Subscript>2</Subscript>SO<Subscript>3</Subscript>–Tb<Superscript>3+</Superscript> System

A simple and selective method to determine norfloxacin using an optical flow-through sensor has been developed. The present sensor was prepared by packing anionic ion exchange resin in a glass tube, followed by introducing KMnO₄ solution to the glass tube for immobilization on resin. The optical sensor is based on the emission intensity from the Tb(III) solution sensitized by norfloxacin. The excitation of norfloxacin occurred by the chemiluminescence from the reaction of KMnO₄ and Na₂SO₄ solutions. The effects of pH, concentration of Tb(III) ion, KMnO₄ and Na₂SO₄ solutions and flow rate of the norfloxacin solution on the chemiluminescence intensity were studied to find the optimum experimental conditions. The emission intensity increased linearly with increasing norfloxacin concentration from 1.0 × 10⁻³ to 1.0 × 10⁻⁸ M and the detection limit (3σ) was 8.7 × 10⁻⁹. The applicability of the present method was demonstrated by determination of norfloxacin in various pharmaceutical preparations and serum sample.     

K*0 and φ meson production in proton–nucleus interactions at ?s=41.6\textGeV\sqrt{s}=41.6\text{GeV}

The inclusive production cross sections of the strange vector mesons K^*0, K̄^*0, and φ have been measured in interactions of 920 GeV protons with C, Ti, and W targets with the HERA-B detector at the HERA storage ring. Differential cross sections as a function of rapidity and transverse momentum have been measured in the central rapidity region and for transverse momenta up to p_T = 3.5 GeV/c. The atomic number dependence is parametrised as σ_pA=σ_pN*A^α, where σ_pN is the proton–nucleon cross section. Within the phase space accessible, α(K^*0)=0.86±0.03, α(K̄^*0)=0.87±0.03, and α(φ)=0.96±0.02. The total proton–nucleon cross sections, determined by extrapolating the differential measurements to full phase space, are σ_pN→K*0=(5.06±0.54) mb, σ_pN→K̄*0=(4.02±0.45) mb, and σ_pN→φ=(1.17±0.11) mb. For all resonances the Cronin effect is observed; compared to the measurements of Cronin et al. for K^± mesons, the measured values of α for φ mesons coincide with those of K⁺ mesons for all transverse momenta, while the enhancement for K^*0/K̄^*0 mesons is smaller.     

Electrical transport properties of CuWO4

The temperature dependence of the electrical conductivity, thermoelectric power and dielectric constant of the antiferromagnetic CuWO₄ have been studied in the temperature range 300–1000 K. The conductivity results can be summarised by the equations σ_I=6.31 × 10⁻³ exp (−0.29 eV/kT) ohm⁻¹ cm⁻¹ in the temperature range 300–600 K and σ_II=3.16 × 10⁵ exp (−1.48 eV/kT) ohm⁻¹ cm⁻¹ between 600 K and 1000 K. The thermoelectric power can be expressed byθ=[− 1.25 (10³/T) + 3.9] mV/K. Initially dielectric constant increases slowly but for high temperatures its increase is fast.     

Observational constraint on generalized Chaplygin gas model

We investigate observational constraints on the generalized Chaplygin gas (GCG) model as the unification of dark matter and dark energy from the latest observational data: the Union SNe Ia data, the observational Hubble data, the SDSS baryon acoustic peak and the five-year WMAP shift parameter. The result is obtained that the best-fit values of the GCG model parameters with their confidence level are A _s=0.73_−0.06^+0.06 (1σ) _−0.09^+0.09 (2σ), α=−0.09_−0.12^+0.15 (1σ) _−0.19^+0.26 (2σ). Furthermore, in this model, we can see that the evolution of equation of state (EOS) for dark energy is similar to quiessence, and its current best-fit value is w _0de=−0.96 with the 1σ confidence level −0.91≥w _0de≥−1.00.     

Optical absorption behavior of Tl<Superscript>+</Superscript> DOPED Rb(Br<Subscript>1–<Emphasis Type="Italic">x</Emphasis></Subscript>I<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>) system

The optical absorption behavior of Tl⁺ doped Rb(Br_1–x I _x ) mixed crystals (with x = 0.00, 0.05, and 0.10) grown under vacuum by slow cooling from the melt has been studied. Absorption spectra of the mixed crystals recorded at room temperature showed that the characteristic A-absorption band of Tl⁺ ions in the Rb(Br_1–x I _x ) system (0.1 mol. %) with x = 0.00 (i.e., RbBr:Tl⁺) broadened with the iodine content towards the low energy side. Changes in the absorption spectra of the mixed crystals are due to creation of some complex centers involving Tl⁺, Br^–, and I^- ions with energy levels inside the band gap while forming the mixed crystal. The absorption spectra of gamma-irradiated mixed crystals showed the F-band, which shifted towards the low energy side due to the existence of iodine ions in the mixed crystals.     

Steady State and Time-Resolved Fluorescence Studies of a Hemagglutinin from Moringa oleifera

The saccharide binding and conformational characterization of a hemagglutinin, a low molecular weight protein from the seeds of Moringa oleifera was studied using steady state and time resolved fluorescence. The lectin binds sugars LacNAc (K _a = 1380 M⁻¹) and fructose (K _a = 975 M⁻¹), as determined by the fluorescence spectroscopy. It has a single tryptophan per monomer which is exposed on the surface and is in a strong electropositive environment as revealed by quenching with iodide. Quenching of the fluorescence by acrylamide involved both static (K _s = 0.216 M⁻¹) and collisional (K _sv = 8.19 M⁻¹) components. The native protein showed two different lifetimes, τ ₁ (1.6 ns) and τ ₂ (4.36 ns) which decrease and get converted into a single one, (2.21 ns) after quenching with 0.15 M acrylamide. The bimolecular quenching constant, k _q was 7.55 × 10¹¹ M⁻¹ s⁻¹. ANS binding studies showed that the native protein has exposed hydrophobic patches which get further exposed at extreme acidic or alkaline pH. However, they get buried in the interior of the protein in presence of 1 M GdnHCl or urea.     

Field theoretic calculation of energy cascade rates in non-helical magnetohydrodynamic turbulence

Energy cascade rates and Kolmogorov’s constant for non-helical steady magnetohydrodynamic turbulence have been calculated by solving the flux equations to the first order in perturbation. For zero cross helicity and space dimensiond = 3, magnetic energy cascades from large length-scales to small length-scales (forward cascade). In addition, there are energy fluxes from large-scale magnetic field to small-scale velocity field, large-scale velocity field to small-scale magnetic field, and large-scale velocity field to large-scale magnetic field. Kolmogorov’s constant for magnetohydrodynamics is approximately equal to that for fluid turbulence (≈ 1.6) for Alfvén ratio 05 ≤r _A ≤ ∞. For higher space-dimensions, the energy fluxes are qualitatively similar, and Kolmogorov’s constant varies asd ^1/3. For the normalized cross helicity σ_c →1, the cascade rates are proportional to (1 − σ_c)/(1 + σ_c , and the Kolmogorov’s constants vary significantly with σ_cc.     

Plasma-filled rippled wall rectangular backward wave oscillator driven by sheet electron beam

Performance of the backward wave oscillator (BWO) is greatly enhanced with the introduction of plasma. Linear theory of the dispersion relation and the growth rate have been derived and analysed numerically for plasma-filled rippled wall rectangular waveguide driven by sheet electron beam. To see the effect of plasma on the TM₀₁ cold wave structure mode and on the generated frequency, the parameters used are: relativistic factor γ = 1.5 (i.e. v/c = 0.741), average waveguide height y ₀ = 1.445 cm, axial corrugation period z ₀ = 1.67 cm, and corrugation amplitude ε = 0.225 cm. The plasma density is varied from zero to 2 ×10¹² cm^− 3. The presence of plasma tends to raise the TM₀₁ mode cut-off frequency (14 GHz at 2 ×10¹² cm^− 3 plasma density) relative to the vacuum cut-off frequency (5 GHz) which also causes a decrease in the group velocity everywhere, resulting in a flattening of the dispersion relation. With the introduction of plasma, an enhancement in absolute instability was observed.     

Precise Quadrupole Moment of the Doubly Closed Shell Plus One Proton Nucleus 41Sc

In order to precisely determine the |eqQ(⁴¹Sc)/h| of ⁴¹Sc(I ^π=7/2⁻, T _1/2=0.596 s) implanted in a TiO₂ single crystal the electric field gradient tensor and anisotropic chemical shift were determined by detecting the Fourier Transformed Pulse-NMR of ⁴⁵Sc(I ^π=7/2⁻, stable) in the crystal at a high field of 7.0 T and 9.4 T. Combining the new |eqQ(⁴¹Sc)/h| value with the Q(⁴⁵Sc)=−(23.6±0.2) fm², also renewed by using the known atomic hyperfine interaction constants and Sternheimer polarization effect, the |Q(⁴¹Sc;I ^π=7/2⁻,T _1/2=0.596 s)|=(15.6±0.3) fm² has been precisely determined. The value is compared with the theoretical Q(⁴¹Sc) given by a shell model code. This revised version was published online in September 2006 with corrections to the Cover Date.     

Solid Substrate–Room Temperature Phosphorimetry for the Determination of Trace Terbutaline Sulfate Based on Its Inhibition Oxidation of Rhodamine 6G by Sodium Periodate

When 1.00 mol l⁻¹ I⁻ is used as ion perturber, rhodamine 6G (Rh 6G) can emit strong and stable room temperature phosphorescence (RTP) on filter paper substrate in KHC₈H₄O₄–HCl buffer solution (pH = 3.50), heated at 70 °C for 10 min. NaIO₄ can oxidize Rh 6G, which makes the RTP signal quench. Terbutaline sulfate (TBS) can inhibit NaIO₄ from oxidizing Rh 6G, which makes the RTP signal of Rh 6G enhance sharply. The content of TBS is linear correlation to ΔIp of the system. Based on the facts above, a new inhibition solid substrate-room temperature phosphorimetry (SS-RTP) for the determination of trace TBS has been established. The linear range of this method is 0.0104–2.08 pg spot⁻¹ (corresponding concentration: 0.026–5.2 ng ml⁻¹, with a sample volume of 0.4 μl) with a detection limit (L.D.) of 2.6 fg spot⁻¹ (corresponding concentration: 6.5 × 10⁻¹² g ml⁻¹), and the regression equation of working curve is ΔIp = 2.040 + 54.54 m_TBS (pg spot⁻¹), n = 6, correlation coefficient is 0.9994. For the samples containing 0.0104 pg spot⁻¹ and 2.08 pg spot⁻¹ TBS, the relative standard deviation (RSD) are 3.8% and 2.3% (n = 8), respectively, indicating good precision. This method has been applied to determination of trace TBS in the practical samples with satisfactory results. The reaction mechanism of NaIO₄ oxidizing Rh 6G to inhibit SS-RTP for the determination of trace TBS is also discussed.     

Superconductivity and magnetic ordering in YBa2(Cu1−x Fe x )3O7

Transverse-and zero-field μSR measurements have been made for YBa₂(Cu_1−x Fe _x )₃O₇ withx=0.04, 0.08 and 0.12. The temperature range studied was from approximately 7.5 K to 100 K. The onset of magnetic ordering commences at about 7.5 K forx=0.04, 10 K forx=0.08 and 20 K forx=0.12. The Gaussian depolarization parameter, σ ofG _x (t) = exp(−σ² t ²/2), is depressed by a factor of about 0.6 forx=0.04, but for thex=0.08 sample σ is depressed by a factor of 10 and increasing suppression is seen as the temperature is lowered below 45 K. This decrease in σ is interpreted in terms of decreasing electronic mean free paths.     

Luminescence of CaGa<Subscript>2</Subscript>Se<Subscript>4</Subscript>:Eu crystals

We have studied photoluminescence and thermoluminescence (PL and TL) in CaGa₂Se₄:Eu crystals in the temperature range 77–400 K. We have established that broadband photoluminescence with maximum at 571 nm is due to intracenter transitions 4f⁶ 5d–4f⁷ (⁸S_7/2) of the Eu²⁺ ions. From the temperature dependence of the intensity (log I–10³/T), we determined the activation energy (E _a = 0.04 eV) for thermal quenching of photoluminescence. From the thermoluminescence spectra, we determined the trap depths: 0.31, 0.44, 0.53, 0.59 eV. The lifetime of the excited state 4f6 5d of the Eu²⁺ ions in the CaGa₂Se₄ crystal found from the luminescence decay kinetics is 3.8 μsec. Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 76, No. 1, pp. 112–116, January–February, 2009.