Development of an infrared hollow waveguide sampler for the detection of organic compounds in aqueous solutions with limited sample volumes.

In this study, an infrared (IR) hollow waveguide sampler was developed to detect organic compounds in aqueous samples with sample volumes less than 50 microL. This sampler was prepared by coating a thin hydrophobic film inside the IR hollow waveguide. After injecting a certain amount of aqueous solution, organic compounds could be absorbed into the hydrophobic film by partitions. By removing the residual water in the hollow waveguide sampler with a nitrogen purging gas, the absorbed organic compounds could be sensed using IR radiation. To investigate the applicability of this hollow waveguide sampler in the detection of small amounts of aqueous samples, an analytical working function was developed following an examination of the parameters which influence the analytical signals. Such factors as the volume of the aqueous solution, the sample concentration, the length of the hollow waveguide, and the sensitivity of this method were investigated. Excellent agreement between the analytical and theoretical predicted values was observed. Upon examining the linear relationship between the analyte signals and the concentration, the regression coefficients were generally higher than 0.998 in the examined concentration range of 1 to 100 ppm. Under the condition that the sample volume was 300 microL and based on three-times the spectra noise level, the calculated detection limits for this method were found at around 1 ppm for the examined analytes.     

Infrared reflection-absorption method for the detection of aromatic compounds in aqueous solutions with limited sample volumes.

An infrared reflection-absorption (IR/RA) method was developed to detect aromatic organic compounds in aqueous solutions where the required sample volume can be as low as 50 microL. Two aluminum plates were used to form the sampling cell for the detection of small amount of aqueous samples. One plate was used as an IR reflection substrate and a second plate, in which several holes were drilled, was placed tightly on the top of the reflection plate to form cavities for sampling. The cavities were further coated with hydrophobic film. After the hydrophobic film dried, a certain amount of aqueous sample was injected to the cavity. Analytes in the aqueous solution were attracted into the hydrophobic film through the solid phase micro-extraction principle. After residual water was removed from the cavity, organic compounds absorbed by the hydrophobic film could be sensed using IR radiation based on the reflection-absorption mode. To investigate the applicability of this type of sensing method for small-volume detection, factors such as the volume of the aqueous solution, the sample concentration, size of the cavity and the sensitivity of this method were investigated. An examination of the linear relationship between the signals and the analyte concentrations showed regression coefficients that were generally in the range of 0.992 to 0.999 for the examined analytes in the concentration range of 10 to 100 ppm. Under the condition that the sample volume was 100 microL and based on three-times the spectra noise level, the calculated detection limits for this method were found at around 1 ppm for the examined analytes.     

Reflection–absorption infrared sensing device for detection of semivolatile aromatic compounds in soils

In this article, a new IR-sensing device is described for the examination of chlorinated aromatic compounds in soils. To prepare this sensing device, a 20-mL glass vial was modified for use in the analysis of soil samples by conventional Fourier-transform infrared (FT-IR) spectroscopy. In this sampling device, an aluminium plate coated with a hydrophobic film was placed on top of the cap of the sample vial to absorb the analytes that evaporated from the soil matrix. After this absorption process was complete, the cap was placed in an FT-IR spectrometer, and the absorbed analytes were detected in the reflection–absorption (RA) mode. To accelerate the rate of evaporation of the analytes, the soil samples were heated to various temperatures. Meanwhile, other factors, such as the moisture content, sampling time, thickness of the hydrophobic film, and the volatilities and concentrations of the analytes, were also examined to optimize the analytical conditions. The results indicated that the time required to reach equilibrium conditions was short, and evaporation/absorption could be achieved within 10?min. With a water content of 10% (v/w) or less, the intensities of the analytical signals were increased greatly when compared with those of dry samples; when the water content was above 10% (v/w), these intensities decreased, partially as a result of the heating efficiency. After examining the compounds that had different vapour pressures, the analytical results indicated that this method was applicable to the examination of compounds that had vapour pressures below 1.0?Torr. Using the optimal conditions determined in this study, the detection limits for semivolatile aromatic compounds were lower than 100?ng/g, and the regression coefficients of the standard curves for compounds that had a vapour pressure lower than 1.0?Torr were larger than 0.99 in the concentration range of 1–100?µg/g.     

An infrared evanescent wave sensing system coupled with a hollow fiber membrane for detection of volatile organic compounds in aqueous solutions.

We have developed an on-line sensing method for the detection of volatile organic compounds (VOCs) in contaminated aqueous solutions by combining a microporous hollow fiber membrane with an infrared (IR) sensing system. Polypropylene microporous hollow fibers were used to separate the VOCs from the aqueous solution into the hollow fibers, which were purged countercurrently for detection by the IR sensing systems. An evanescent-wave-type IR sensing system was used to detect the VOCs that were purged from the hollow fibers. The sensing element was coated with polyisobutylene (PIB) to concentrate the VOCs for their detection. To study the performance of this system, we examined a number of factors, such as the purging flow rate, the sample flow rate, and the volatilities of the VOCs. The results indicate that an increase in the purging flow rate reduces the analytical signal significantly, especially for purging flow rates >2 mL/min. The pumping flow rate for the aqueous sample also influenced the analytical signals, but far less sensitively. The volatilities of the examined compounds also affected the analytical signals: the higher the volatility of the compound, the lower the intensity of the analytical signals and the shorter the time required to reach the equilibrium signal. From an examination of the dynamic range of this proposed method, a regression coefficient >0.994 was obtained for concentrations below 250 mg/L, even under non-equilibrium conditions. The response time of the system was studied in an effort to examine the suitability of using this sensing method for automatic detection. The results indicate that new equilibrium conditions were established within 3 min for highly volatile compounds, which suggests that on-line monitoring of the levels of VOCs can be performed in the field.     

Membrane-introduced infrared spectroscopic chemical sensing method for the detection of volatile organic compounds in aqueous solutions

A novel membrane-introduced infrared (IR) chemical sensing method has been developed for the detection of volatile organic compounds (VOCs) in aqueous solutions. In this method, a porous Teflon membrane was used to eliminate the problems associated with conventional IR spectroscopic sensing methods. The porous Teflon membrane was sealed below an IR spectroscopic sensing element pre-coated with a hydrophobic film and a two-channel flow cell configuration was established. In this configuration, the aqueous sample was allowed to pass through the lower channel and the VOCs that penetrated through the membrane to the upper channel were detected by the IR sensor. In this manner, the performance of the sampling at the headspace was improved while the problems caused by the presence of water were eliminated. Meanwhile, using a purging channel allowed the sensing element to be regenerated rapidly and enabled automation of the detection process. The parameters that influenced the analytical signals were studied, such as the sampling flow rate, the pH and ionic strength of the sample solutions, the effect of the volatilities of the VOCs, and the regeneration efficiency of the sensing element. The results indicated that the analytical signals were insensitive to the sampling flow rate and to the pH and ionic strength of the sample solutions. The results obtained from the detection of seven different volatile compounds indicated that this method is highly suitable for the detection of organic compounds that have vapor pressures >1 Torr and that it is potentially usable for organic compounds that have vapor pressures between 20 mTorr and 1 Torr. The regression analysis of the standard curves indicated that a regression coefficient (R(2)) > 0.99 was obtainable in the concentration range from 1 to 100 microg mL(-1). The detection limits for the tested compounds were around a few hundred ng mL(-1).     

Development of a solid-phase microextraction/reflection-absorption infrared spectroscopic method for the detection of chlorinated aromatic amines in aqueous solutions.

In this paper, the reflection-absorption infrared (IR) spectroscopic method combined with the principle of solid-phase micro-extraction (SPME) is proposed to detect chlorinated aromatic amines in aqueous solutions. This proposed method provides simplicity in both the optical system and equipment setup. Compared to the SPME/attenuated total reflection-IR method, this method reduces the cost for internal-reflection elements and optical systems. Meanwhile, it has no SPME/transmission IR method problems, which require high polymer film preparation techniques to obtain a standing film that has no physical/chemical property changes when immersed in an aqueous solution. The typical linear coefficients obtained using this method for chloroanilines in aqueous solutions are around 0.995 and the detection can be lower than 100 ppb. The thickness of the hydrophobic film is relatively important in the SPME/ATR-IR method, but the uncertainty caused by the film thickness can be partially eliminated in the proposed method. This is because the IR signals are proportional to the film thickness and can be corrected using hydrophobic film signals. The low detection limits have also indicated that this proposed method can compete with the currently existing IR methods, but allowing much simpler detection.     

Optimisation of an integrated optical evanescent wave absorbance sensor for the determination of chlorinated hydrocarbons in water

The suitability of an integrated optical chemical sensor for the determination of highly volatile chlorinated hydrocarbons in aqueous solutions has been proven. The analytes are detected by NIR absorption spectrometry in the evanescent field of an integrated optical strip waveguide generated in a BGG31 (Schott, Germany) glass substrate, which is coated with a hydrophobic polymer superstrate as sensing layer. It has been shown that the sensitivity increases when the refractive index of the superstrate is increased from 1.333 up to 1.46. Different UV-cured polysiloxanes with low cross sensitivity to water have been prepared. Due to the good light transmission properties of the IO-sensors prepared by this method, quantitative measurements have been performed with the model system trichloroethene (TCE) in water. A detection limit of 22 ppm has been found and the sensor response times (t(90)-value) are between five and fourteen minutes for a coating thickness of around 30 microm. The sensor response is totally reversible. The analyte desorbes in air within 2 min. The enrichment of trichloroethene in the polysiloxane coating can be described by film diffusion through the aqueous boundary layer as rate determining step.     

Combination of a Mid-infrared Hollow Waveguide Gas Sensor with a Supported Capillary Membrane Sampler for the Detection of Organic Compounds in Water

A Fourier transform infrared (FT-IR) spectroscopy based gas sensor for continuous analysis of liquid phase samples has been developed, coupling a short hollow waveguide (HWG) gas cell with a supported capillary membrane sampler (SCMS) probe. Passing an inert carrier gas through the thin-walled tubular silicon membrane enables the permeation of volatile organic compounds (VOCs) present in aqueous solution and facilitates their continuous and quantitative detection in the infrared hollow fiber by multiple internal reflection spectroscopy. The sensitivity of the sensor system has been determined at the ppb (μg/L) concentration level and the response time ranges from few minutes to 30 min, depending on the analyte and the permeation properties of the sampling membrane.

The experimental set-up consists of Bruker Vector 22 FT-IR spectrometer with an externally aligned 50 cm long silica HWG coupled to the SCMS, which is immersed into a glass flask filled with analyte solution and kept under constant stirring.

Aqueous solutions of benzene, toluene, xylene isomers and chloroform were qualitatively and quantitatively analyzed confirming the feasibility of this sensor approach for environmental analysis.     

Solid-phase microextraction under controlled agitation conditions for rapid on-site sampling of organic pollutants in water

An electric drill coupled with a solid-phase microextraction (SPME) polydimethylsiloxane (PDMS) fiber or a PDMS thin film was used for rapid sampling of polycyclic aromatic hydrocarbons (PAHs) in aqueous samples. Laboratory experiments demonstrated that the sampling rates of SPME fiber and thin film can be predicted theoretically. Compared with the SPME fiber, the PDMS thin film active sampler exhibited a higher sampling rate and much better sensitivity due to its higher surface-to-volume ratio and its larger extraction phase volume. The amount of the analytes extracted by the thin film was around 100 times higher than those obtained by fiber, for both 5 min rapid sampling and equilibrium extraction. A new thin film active sampler was then developed for rapid on-site water sampling. The sampling kit included a portable electric drill, a copper mesh pocket, a piece of thin film, and a liner. Laboratory experiments indicated that the sampling remained in the linear uptake phase with this sampler to 8 min for the PAHs. Field test illustrated that this novel sampler was excellent for rapid on-site water sampling due to its short sampling period, high sampling efficiency and durability The thin film sampling kit facilitates on-site sampling, sample preparation, storage and transport. This new sampler is more user-friendly and easier to commercialize than previous samplers.     

Optimisation of an integrated optical evanescent wave absorbance sensor for the determination of chlorinated hydrocarbons in water

The suitability of an integrated optical chemical sensor for the determination of highly volatile chlorinated hydrocarbons in aqueous solutions has been proven. The analytes are detected by NIR absorption spectrometry in the evanescent field of an integrated optical strip waveguide generated in a BGG31 (Schott, Germany) glass substrate, which is coated with a hydrophobic polymer superstrate as sensing layer. It has been shown that the sensitivity increases when the refractive index of the superstrate is increased from 1.333 up to 1.46. Different UV-cured polysiloxanes with low cross sensitivity to water have been prepared. Due to the good light transmission properties of the IO-sensors prepared by this method, quantitative measurements have been performed with the model system trichloroethene (TCE) in water. A detection limit of 22 ppm has been found and the sensor response times (t₉₀-value) are between five and fourteen minutes for a coating thickness of around 30 m. The sensor response is totally reversible. The analyte desorbes in air within 2 min. The enrichment of trichloroethene in the polysiloxane coating can be described by film diffusion through the aqueous boundary layer as rate determining step.     

Characterization of cyclodextrin modified infrared chemical sensors. Part II. Selective and quantitative determination of aromatic acids

In this paper, the selectivity and sensitivity of cyclodextrin (CD) modified infrared (IR) chemical sensor in detection of aromatic acids in aqueous solutions were reported. To eliminate the interference from water, the technique of attenuated total reflection was employed. By surface treated with CD molecules on the internal reflection elements, the sensors were selective in sensing of aromatic acids compared to aromatic compounds with other functional groups. To facilitate the use of this method for the quantitative analyses of aromatic acids in aqueous solutions, analytical functions were also developed in this work and a linear relationship between analytical responses and concentrations of analytes can be obtained. To optimize the analytical conditions, the factors that influence the IR spectroscopic signals were examined. These factors included response time, CD loadings of the sensors, pH effect on response, regeneration efficiency and stability of sensors. Under the optimal conditions, the detection limits for aromatic acids at a detection time of 2 min can be <100 μg/L. Meanwhile, the dynamic linear range for detection was only ca. two orders of magnitude if direct IR signals were used. Using the analytical function developed in this work, the linearity can be extended up to a concentration of 100 mg/L.     

A novel sol-gel-based amino-functionalized fiber for headspace solid-phase microextraction of phenol and chlorophenols from environmental samples

A novel amino-functionalized polymer was synthesized using 3-(trimethoxysilyl) propyl amine (TMSPA) as precursor and hydroxy-terminated polydimethylsiloxane (OH-PDMS) by sol–gel technology and coated on fused-silica fiber. The synthesis was designed in a way to impart polar moiety into the coating network. The scanning electron microscopy (SEM) images of this new coating showed the homogeneity and the porous surface structure of the film. The efficiency of new coating was investigated for headspace solid-phase microextraction (SPME) of some environmentally important chlorophenols from aqueous samples followed by gas chromatography–mass spectrometry (GC–MS) analysis. Effect of different parameters influencing the extraction efficiency such as extraction temperature, extraction time, ionic strength and pH was investigated and optimized. In order to improve the separation efficiency of phenolic compounds on chromatography column all the analytes were derivatized prior to extraction using acetic anhydride at alkaline condition. The detection limits of the method under optimized conditions were in the range of 0.02–0.05 ng mL⁻¹. The relative standard deviations (R.S.D.) (n = 6) at a concentration level of 0.5 ng mL⁻¹ were obtained between 6.8 and 10%. The calibration curves of chlorophenols showed linearity in the range of 0.5–200 ng mL⁻¹. The proposed method was successfully applied to the extraction from spiked tap water samples and relative recoveries were higher than 90% for all the analytes.     

Development and application of microporous hollow fiber protected liquid-phase microextraction via gaseous diffusion to the determination of phenols in water

A new organic solvent-free microextraction technique termed liquid-gas-liquid microextraction (LGLME) was developed. In this technique, a small amount (6 microl) of aqueous acceptor solution (0.5M NaOH) is introduced into the channel of a 2.65 cm polypropylene hollow fiber. The hollow fiber is then immersed in an aqueous sample donor solution. The aqueous acceptor phase in the channel of the hollow fiber is separated from the sample solution by the hydrophobic microporous hollow fiber wall with air inside its pores. The analytes (phenols) passed through the microporous hollow fiber membrane by gas diffusion and were then trapped by the basic acceptor solution. After extraction, the acceptor solution was withdrawn into a microsyringe and injected into a capillary electrophoresis sample vial for subsequent analysis. Limits of detection of between 0.5 and 10 microg/l for eight phenols could be achieved. The relative standard deviations (n=6) of this technique between 2.7 and 7.6%. The technique also provides good enrichment factors for all the eight analytes.     

Micelle-mediated extraction for concentrating hydrophobic organic compounds

An extraction method based on polymer-induced phase separation of aqueous micellar solutions of octyl-beta-D-thioglucoside (OTG) was assessed for concentrating hydrophobic analytes. Various hydrophobic compounds such as polycyclicaromatic hydrocarbons, alkylbenzenes, alkylphenols, chlorobenzenes, chlorophenols, phthalic esters, pesticides, and steroid hormones could be efficiently concentrated into a small volume of surfactant-rich phase, while hydrophilic matrix components remained in the bulk aqueous phase. The surfactant-rich phase containing concentrated OTG could be directly introduced into the hygro-organic mobile phase of high-performance liquid chromatography with ultra-violet photometric detection. The application of this method greatly enhanced the signal intensity in the chromatogram while reducing the interference of matrix components.     

Microwave assisted headspace controlled-temperature single drop microextraction for liquid chromatographic determination of chlorophenols in aqueous samples

We report on an efficient one-step sample preconcentration technique by coupling microwave heating and cloud vapor zone (CVZ)-based headspace controlled-temperature single drop microextraction (HS-CT-SDME), and its application to headspace extraction of chlorophenols in aqueous solutions. Microwave irradiation is utilized to accelerate evaporation of analytes into the headspace sampling zone for the direct extraction of aqueous chlorophenols. A microdrop of extractant is suspended at the bottom of a bell-mouthed micropipette tip connected to a microsyringe needle. An external cooling system was adopted to control the formation of the CVZ around the SDME tip in the headspace sampling area. In the CVZ procedure, the warm headspace vapor is quickly cooled near the SDME tip, thus forming a dense cloud of analyte-water vapor; thereby enhancing the partition of the analytes into the SDME solvent. The chlorophenols are then determined by LC-UV detection. Under the optimized experimental conditions, the analytical signal is linearly related to the concentration of the chlorophenols range of 2.5–250?ng?mL^?1. The detection limits vary from 0.3 to 0.7?ng?mL^?1, and the precision (expressed as the relative standard deviation) from 3.7 to 13.3?%. The method was validated with real water samples, and the spiked recovery ranged between 92 and 103.1?% for river water, and between 85.1?% and 98.6?% for lake water. Compared to other methods, microwave assisted HS-CT-SDME is simple, rapid, sensitive, inexpensive and eco-friendly, and requires less sample and organic extractant.

Parts per quadrillion level ultra-trace determination of polar and nonpolar compounds via solvent-free capillary microextraction on surface-bonded sol-gel polytetrahydrofuran coating and gas chromatography-flame ionization detection

Sol-gel polytetrahydrofuran (poly-THF) coating was developed for high-sensitivity sample preconcentration by capillary microextraction (CME). Parts per quadrillion (ppq) level detection limits were achieved for both polar and nonpolar analytes through sample preconcentration on sol-gel poly-THF coated microextraction capillaries followed by gas chromatography (GC) analysis of the extracted compounds using a flame ionization detector (FID). The sol-gel coating was in situ created on the inner walls of a fused silica capillary using a sol solution containing poly-THF as an organic component, methyltrimethoxysilane (MTMOS) as a sol-gel precursor, trifluoroacetic acid (TFA, 5% water) as a sol-gel catalyst, and hexamethyldisilazane (HMDS) as a deactivating reagent. The sol solution was introduced into a hydrothermally-treated fused silica capillary and the sol-gel reactions were allowed to take place inside the capillary for 60 min. A wall-bonded coating was formed due to the condensation of silanol groups residing on the capillary inner surface with those on the sol-gel network fragments evolving in close vicinity of the capillary walls. Poly-THF is a medium polarity polymer, and was found to be effective in carrying out simultaneous extraction of both polar and nonpolar analytes. Efficient extraction of a wide range of trace analytes from aqueous samples was accomplished using sol-gel poly-THF coated fused silica capillaries for further analysis by GC. The test analytes included polycyclic aromatic hydrocarbons (PAHs), aldehydes, ketones, chlorophenols, and alcohols. To our knowledge, this is the first report on the use of a poly-THF based sol-gel material in analytical microextraction. Sol-gel poly-THF coated CME capillaries showed excellent solvent and thermal stability (>320 degrees C).     

Development of the Headspace SPME/ATR‐IR Method for Detection of Chlorinated Aromatic Compounds in Soils

In this paper, a new method based on attenuated total reflection infrared (ATR‐IR) spectroscopy was developed to detect chlorinated aromatic compounds in soil. To eliminate the problems associated in inspection of soil samples by the ATR‐IR method, chlorinated compounds were evaporated from soil matrices and detected in the headspace. The sensing device was constructed by an internal reflection element (IRE) coated with a hydrophobic film to attract and concentrate chlorinated compounds evaporated to the headspace. Factors that influence the analytical signals were studied such as the moisture content, volatilities of analytes, and effect of heating temperature. Results indicated that the addition of thermal energy to the soil sample resulted in an increase of IR signal. However, the IRE was also warmed up and caused a slight decrease of the IR signals after a long detection time. The studies of the influence of moisture indicated that a small amount of water present in soils could tremendously increase the intensity of detected IR signals. The further increase of moisture contents resulted in a decrease of the analytical signals, and the optimal signal was found when soil samples contained 5% (v/w) water. Results in analyses of compounds with different volatilities indicated that even with vapor pressure lower than 0.017 Torrs, quality IR spectra could still be obtained. Using the optimal conditions found in this work, the results in determination of five compounds in soil samples indicated that the linear regression coefficients (R‐square) were higher than 0.992 with detection limits around a few hundreds of ppb.     

A gravity driven micro flow injection wetting film extraction system on a polycarbonate chip

A micro flow injection wetting film liquid-liquid extraction system has been developed for trace analyte concentration and on-chip detection. A hydrophobic channel fabricated on a polycarbonate chip was used to support the wetting film, and hydrostatic pressure generated by the difference in liquid levels was employed to drive the fluids. Sequential injection of segments of aqueous sample solution and organic solvent was conducted by switching the sample- or solvent-containing vials to an on-chip sampling probe, and detection was performed by a co-focused, laser induced fluorescence detector. Using butyl rhodamine B as a model analyte and butanol as the solvent for both film-coating and elution, various experimental conditions such as hydrostatic pressure, coating time, channel length, sampling volume, and sample acidity were investigated. Under optimized conditions, a 24-fold enrichment factor was obtained with the consumption of about 3 μL sample solution, and a detection limit (3σ) of 6.0 × 10⁻⁹ M butyl rhodamine B was achieved at the sampling rate of 19 h⁻¹. Eleven consecutive runs of a 1.0 × 10⁻⁵ M butyl rhodamine B solution produced a relative standard deviation of 1.5% for the detected fluorescence signals.     

A novel approach to automation of dynamic hollow fiber liquid-phase microextraction

An automated dynamic two-phase hollow fiber microextraction apparatus combined with high-performance liquid chromatography was developed for extraction and determination of chlorophenoxy acid (CPA) herbicides from environmental samples. The extraction device, called TT-extractor, consists of a polypropylene hollow fiber mounted inside a stainless steel tube by means of two tee-connectors in flow system. An organic solvent, which fills the lumen and the pores of the hydrophobic fiber, is pumped through the fiber repeatedly and the sample is pumped along the outer side of the fiber. The factors affecting the dynamic hollow fiber liquid-phase microextraction (DHF-LPME) of target analytes were investigated and the optimal extraction conditions were established. To test the applicability of the designed instrument, CPAs were extracted from environmental aqueous samples. The limits of detection (LODs) as low as 0.5 μg/L, linear dynamic range in the range of 1-100 μg/L and the relative standard deviations of <7% were obtained. The developed method can provide perconcentration factors as large as 230. A hollow fiber membrane can be used at least 20 times with neither loss in the efficiency nor carryover of the analytes between runs. The system is cheap and convenient and requires minimal manual handling.     

Direct determination of chlorophenols in landfill leachates by solid-phase micro-extraction-gas chromatography-mass spectrometry

Landfill leachates represent a serious environmental concern with regard to trace priority pollutants introduced into the aquatic environment. From the analytical point of view, they constitute complex matrices because of their high organic matter content and competition with the trace analytes in the extraction procedure. Although the use of SPME to extract chlorophenols in leachates has already been described in several publications, the limited number of chlorophenols restricts this analysis field of application. This paper presents a new analytical methodology to determine 13 chlorophenols and phenol by SPME-GC-MS in landfill leachates. The overall analysis was performed in 90 min and the detection limits range from 0.005 microg/l (pentachlorophenol) to 2.5 microg/l (phenol). Reproducibility, expressed by the coefficient of variation of repeated extractions at different concentration levels of the analytes, was on average inferior to 10%. Recovery, evaluated by standard addition to leachates, was 86.2% on average. Pentachlorophenol, 2,3,4,5-tetrachlorophenol and 2,3,4,6-tetrachlorophenol were the sole analytes detected at nanogram level in the landfill leachates analysed.