Collection of iron(III) from homogeneous aqueous solutions on membrane filters using Chromazurol B with Triton X-100.

A membrane filtration method was examined concerning the effective collection of iron(III) from a homogeneous aqueous solution with Chromazurol B (CAB), one of the triphenylmethane dyes, as a precipitating reagent in the presence of a non-ionic surfactant, polyethylene glycol mono[4-(1,1,3,3-tetramethylbutyl)phenyl]ether (Triton X-100). A formed blue Fe(III)-CAB complex was collected as a precipitate on a membrane filter by filtration under suction from a homogeneous aqueous solution in the pH range over about 2. The original solution was prepared at a concentration ratio of CAB to Fe(III) of to 10, and that of Triton X-100 to CAB of 10 to 100. It was then adjusted to a pH value of between 1.0 and 6.5. A linear relationship (r = 0.999) was obtained between the initial concentration and the found one of Fe(III) in the range of 2.0 x 10(-5) to 4.0 x 10(-4) mol dm(-3) at a fixed concentration ratio of CAB to Fe(III) of 3 and that of Triton X-100 to CAB of 20. This membrane filtration with CAB and Triton X-100 may be utilized for the separation of Fe(III) as a background species.     

Electrokinetic characterization of polystyrene–non-ionic surfactant complexes

An experimental study on the electrophoretic mobility (μ_e) of polystyrene particles after the adsorption of non-ionic surfactants with different chain lengths is described. Two sulphate latexes with relatively low surface charge densities (3.2 and 4.8 μC cm⁻²) were used as solid substrate for the adsorption of four non-ionic surfactants, Triton X-100, Triton X-165, Triton X-305 and Triton X-405, each one with 9–10, 16, 30 and 40 molecules of ethylene oxide (EO), respectively. The electrophoretic mobility of the polystyrene–non-ionic surfactant complexes was studied versus the amount of adsorbed surfactant (Γ). The presence of non-ionic surfactant onto particles surface seems to produce a slight shifting of the slipping plane because the mobilities of the different complexes display a very small decreasing. The increase in the number of EO chains in the surfactant molecule seems to operate as a steric impediment which decreases the number of adsorbed large surfactant molecules. The electrophoretic mobilities of the latex–surfactant complexes with maximum adsorption were measured versus the pH and ionic strength of the dispersion. While the different complexes showed a similar qualitative behaviour compared with that of the bare latex against the pH, the adsorption of the surfactant reduces the typical maximum in the μ_e−log[electrolyte].     

Simultaneous cloud-point extraction of nine cations from water samples and their determination by flame atomic absorption spectrometry.

The cloud-point methodology was successfully employed for the preconcentration of heavy metal cations at trace levels from aqueous samples prior to flame atomic absorption spectrometry (FAAS). Cations were taken into a complex with 8-quinolinol in an aqueous non-ionic surfactant, Triton X-114, medium and concentrated in the surfactant rich phase by bringing the solution to the cloud-point temperature. The preconcentration of only 100 mL of the solution with 1% Triton X-114 and 10(-3) M 8-quinolinol at pH 7.0 gave a preconcentration factor higher than 100 for most cations. Under these conditions, the detection limits of the cloud-point extraction-FAAS system were 0.8 - 15 microg/L.     

Use of surfactant-mediated phase separation (cloud point extraction) with affinity ligands for the extraction of hydrophilic proteins

The feasibility of utilizing a zwitterionic surfactant, 3-(nonyldimethylammonio)propylsulfate, or nonionic surfactant, Triton X-114, mediated phase separation in conjunction with affinity ligands was studied for hydrophilic protein extractions. Below (or above) its critical temperature (so-called cloud point), aqueous solutions of zwitterionic (or nonionic) surfactants separate into two immiscible phases, a surfactant-rich phase and an aqueous phase. Avidin was successfully extracted into the zwitterionic surfactant-rich phase when a small amount of the affinity ligand, N- biotinoyl)dipalmitoyl- l -alpha- phosphatidyl ethanolamine, was added to the system. It was not possible to extract hexokinase into the surfactant-rich phase of the nonionic surfactant, Triton X-114, even if a considerable amount of octyl-beta-d-glucoside was added to the solution as an affinity ligand. In contrast, the use of the zwitterionic surfactant and octyl-beta-d-glucoside as an affinity ligand proved to be effective for the extraction of hexokinase. The hexokinase extraction efficiency was found to depend upon the solution pH and the concentration of the affinity ligand in the system. The results clearly indicate that hydrophilic proteins can be successfully extracted with surfactant mediated phase separations (cloud point extractions) via use of the zwitterionic surfactant, 3-(nonyldimethylammonio)propylsulfate, and appropriate affinity ligands. Some advantages of zwitterionic surfactants in such extractive processes relative to that of nonionic surfactants are delineated.     

Removal of detergent and solvent from solvent-detergent-treated immunoglobulins.

The solvent-detergent (S/D) method was applied for inactivation of lipid-enveloped viruses during the production of immunoglobulins. Amberlite XAD-7 resin was used for removal of solvent (tri-n-butyl phosphate, TnBP) and detergent (Triton X-100) after the performed S/D inactivation procedure. The S/D reagents from the immunoglobulin preparation were adsorbed on Amberlite XAD-7, while immunoglobulins passed through the column and retained their biological activity. Using the method developed here, the final immunoglobulin preparation contains less than 1 ppm of Triton X-100 and less than 2 ppm TnBP.     

Salting-out surfactant extraction of porphyrins and metalloporphyrin from aqueous non-ionic surfactant solutions

A number of cloud point temperature-depressing electrolytes have been investigated for the separation of a non-ionic surfactant (Triton X-100) from aqueous solutions and the corresponding extraction of the organic solutes into the smaller volume surfactant-rich phase using the salting-out method. High extraction efficiencies and preconcentration factors were obtained at room temperature for the extraction of several hydrophilic and hydrophobic metal-free porphyrins (uroporphyrin, coproporphyrin, protoporphyrin and hematoporphyrin) and one metalloporphyrin (iron-protoporphyrin) that were dissolved in the aqueous non-ionic surfactant solutions. Possible mechanisms responsible for the efficient extraction of these important biological molecules into the surfactant-rich layer are discussed.     

Parameters Involved in the Sol-Gel Transition of Titania in Reverse Micelles

Titania nanoparticles and gels are synthesized in reverse micelles with either an ionic (AOT) or a non-ionic (Triton X-100) surfactant in alkanes with low water contents. Acids were in some cases dissolved in the aqueous phase. Whereas the size of the sol nanoparticles is independent of the micellar composition, the kinetics of the sol-gel transition are not. The gelation time is shorter for the non-ionic surfactant and becomes longer as the acid content in the water increases, and for smaller anions of equal charge.     

Gamma-radiolysis of Triton X-100 aqueous solution

The decomposition of the non-ionic surfactant Triton X-100 in gamma-irradiated deaerated aqueous solution is mainly attributed to the attack of OH radicals and H atoms. The mechanisms of these reactions were investigated in detail, including the influence of pH and dose rate. The RCHOH radicals formed by OH attack on alcohol molecules can decompose the surfactant in aqueous solution.     

Non-ionic surfactant catalyzed synthesis of Betti base in water

We have developed an efficient non-ionic surfactant (Triton X-100) catalyzed multicomponent synthesis of Betti base from secondary amine, aromatic aldehydes, and β-naphthol using Mannich-type reaction in water. Lewis and Brønsted acid catalysts, ionic and non-ionic surfactant have been screened for the reaction. Non-ionic surfactant (Triton X-100) gave the best results and the reaction proceeds through the imine formation, which is stabilized by colloidal dispersion and undergoes nucleophilic addition to afford the corresponding N,N-dialkylated Betti base in excellent yields.     

Estimation of non-ionic, surface-active substances in aqueous solutions by means of the Controlled Growth Mercury Electrode

In this paper, a quick and simple tensammetric method of estimation of non-ionic surfactants (NS) in aqueous solutions is proposed. The method makes use of the variation in the differential capacity of double layer in relation to the time of accumulation (C(d)-t(acc)) of non-ionic surfactants at the hanging mercury drop electrode, generated by a single, very quick opening of the valve. Under such conditions, the capacity current measured at the potential of maximum adsorption diminishes with accumulation time of non-ionic surfactants. The proposed method, which was verified for model surfactant (Triton X-100), may also be applied in the determination of other NS. Modifications in construction of the CGME electrode and its improved metrological parameters played an important role in the presented procedure. In addition, other measurements were performed using standard electrochemical techniques, whereby current-time and differential capacity-potential curves were recorded. Satisfactory results were obtained in the determination of Triton X-100 in the range from 0.05 to 20 mg L(-1) (R.S.D.=6%, recovery=94-103%, r=0.999, DL=0.15 mg L(-1)). Applicability of the method was presented using the water samples from Bia?ka and Dunajec rivers, from which NS were removed by addition of fumed silica.     

Screening of urinary coproporphyrin using cloud point extraction and chemiluminescence detection

A simple screening test was developed for the sensitive and selective measurement of urinary coproporphyrin. In this screening test, efficient and selective extraction/pre-concentration of coproporphyrin from the aqueous medium(urine) into a much smaller volume phase containing a common non-ionic surfactant (Triton X-100) and ethyl acetate was accomplished by the addition of a relatively large amount of a cloud point depressing electrolyte (K(3)PO(4)) into the sample solution to effect cloud point separation. Sensitive and selective detection of coproporphyrin in the mixed Triton X-100 and ethyl acetate phase was performed via chemical excitation using the peroxyoxalate chemiluminescence reaction. The effects of surfactant and cations (from the cloud point depressing electrolyte) on the chemiluminescence intensity of coproporphyrin were briefly investigated. Furthermore, the spectrum of urinary coproporphyrin obtained using the present chemiluminescence method was briefly compared with that obtained from fluorescence method.     

Interactions of Triton X-100 with sphingomyelin and phosphatidylcholine monolayers: influence of the cholesterol content

The presence of microdomains, called lipid rafts, in biological membranes is usually explained by lateral segregation between specific lipids and proteins. These rafts present similarities with the membrane domains isolated by their non-ionic detergent-resistance at 4 degrees C. They are enriched in sphingomyelin and cholesterol as compared with the outer leaflet of eukaryotic cell membranes. To understand the role played by the lipids enriched in rafts in their resistance to solubilization by detergents, the interactions between these lipids and the non-ionic detergent Triton X-100 were studied by using different lipid monolayers at the air-water interface. The influence of Triton X-100 on the Langmuir isotherms (i.e. surface pressure/area isotherms) of monolayers containing sphingomyelin and cholesterol at different mole ratios was analyzed and the results were compared with the influence of Triton X-100 on monolayers containing a phosphatidylcholine bearing a saturated and an unsaturated fatty acid (i.e. palmitoyloleylphosphatidylcholine) and cholesterol. This phosphatidylcholine was chosen since the phosphatidylcholines present in rafts isolated from bovine kidney could contain about 50% of saturated fatty acids. Triton X-100 induces an increase in the condensing effect observed as compared with ideal mixture of phospholipid/cholesterol. Triton X-100-induced changes in the morphology of the monolayers were visualized by Brewster angle microscopy, which confirmed the differences of behavior observed by analyzing the isotherms.     

Micellar effects on absorption spectra and protolytic equilibria of phenyl-pyridyl-ketones

The absorption spectra of the three isomeric phenyl-pyridyl-ketones were studied in anionic (SLS), cationic (CTAB) and non-ionic (Triton X-100) micellar solutions. The spectral changes of the n, π* transition in micelles compared to net water provided information on the location of the ketone molecules in the micelle and the partitioning of ketones between micelles and water. The apparent pK^a values of the three pyridyl ketones were determined in anionic, cationic and non-ionic micelles and compared to those in aqueous solution. The results indicate that the ketones reside within the interfacial head group region of the micelle. This location affects the protolytic equilibria: a decrease in nitrogen basicity in Triton X-100 (ΔK^a∼−0.6) and CTAB (ΔpK^a−0.5) and an increase in SLS (ΔpK^a+1.5) are attributed to a reduced polarity at the micelle surface and to an electrostatic surface potential.     

Determination of beryllium and selenium in human urine and of selenium in human serum by graphite-furnace atomic absorption spectrophotometry.

For human urine beryllium (Be), each sample (500 microl) was diluted (1+1) with Nash reagent (containing 0.2% (v/v) acetylacetone and 2.0 M ammonium acetate buffer at pH 6.0) and then a 20-microl volume of Triton X-100 (0.4%, v/v) aqueous solution was added. An aliquot (10 microl) of the diluted urine mixture was introduced into a graphite cuvette and was atomized according to a temperature program. The method detection limit (MDL, 3sigma) for Be was 0.37 microg/l in the undiluted urine sample and the calibration graph was linear up to 65.0 microg/l. Calibration graphs were prepared by the standard addition method. Accuracies of 98.6-102% were obtained when testing standard reference material (SRM 2670) freeze dried human urine samples. Precision (relative standard deviation, RSD) for urine Be was < or = 2.3% (withinrun, n = 5) and was < or = 3.0% (between-run, n = 3). For human urine and serum selenium (Se), samples (100 microl) were diluted with HNO3 (0.2%, v/v) to make a (1+1) dilution for urine analysis or a (1+4) dilution for serum analysis. An additional aliquot (10 microl) of Triton X-100 (0.1%, v/v) was added to each 200 microl of (1+1) diluted urine (or 20 microl of the Triton X-100 was added to each 500 microl of (1+4) diluted serum) sample. After the diluted sample mixture (10 microl) was introduced into a graphite cuvette, the corresponding chemical modifier (10 microl, containing Ni2+ + Pd + NH4NO3 in HNO3 (0.2%, v/v)) was added to it and the mixture was atomized. The MDL (3sigma) for Se in urine and in serum was 4.4 and 21.4 microg/l in undiluted sample, respectively, and the calibration graphs were linear up to 150 and 400 microg/l. Accuracies of urine Se were 98.9 - 99.4% by testing SRM 2670 (NIST) urine standards with RSD (between-run, n = 3) within 2.9%; and that of serum Se was 97.2% when testing a certified second-generation human serum (No. 29, #664) with RSD (between-run, n = 3) of 1.4%. The proposed method can be applied easily, directly, and accurately to the measurement of Be and Se in real samples (including six urine Se and four serum Se from patients of Blackfoot Disease in Taiwan).     

A new method for the determination of the critical micelle concentration of Triton X-100 in the absence and presence of beta-cyclodextrin by resonance Rayleigh scattering technology

A new method for the determination of the critical micelle concentration (CMC) of Triton X-100 in aqueous solution and beta-cyclodextrin solution by resonance Rayleigh scattering (RRS) has been developed. The method is based on the measurement of the RRS intensity of different concentration of Triton X-100 in aqueous solution and beta-cyclodextrin solution (6.0 x 10(-4) mol l(-1)). When the RRS intensities were plotted against the concentration of Triton X-100, an inflection point appeared at the Triton X-100 concentration of 5.0 x 10(-4) mol l(-1) in aqueous solution and 1.1 x 10(-3) mol l(-1) in beta-cyclodextrin solution, respectively. These values of concentration corresponded to the CMC of Triton X-100 in aqueous solution and beta-cyclodextrin solution, which also agreed closely with the results reported by surface tension and UV-Vis absorption spectrophotometry. Therefore, the present RRS method is very convenient, rapid and accurate and can be used as a new technology for the determination of CMC values of surfactants without any probe. The relationship between the RRS intensity and the concentration, aggregate state and the aggregate molecular size of Triton X-100 has been primarily discussed.     

Determination of trace alpha-fetoprotein variant by affinity adsorption solid substrate-room temperature phosphorimetry and its application to the forecast of human diseases

In the presence of ion perturber LiAc, 4-generation polyamidoamine dendrimers (4G-D) could emit strong and stable room temperature phosphorescence (RTP) signal at on nitrocellulose membrane (NCM), and Triton X-100 could sharply enhance the RTP signal of 4G-D. Triton X-100-4G-D was used to label concanavalin agglutinin (Con A) to get the labeling product Triton X-100-4G-D-Con A. Quantitative specific affinity adsorption (AA) reaction between Triton X-100-4G-D-Con A and α-fetoprotein variant (AFP-V) could be carried out on the surface of NCM, whose product Triton X-100-4G-D-Con A-AFP-V could emit strong and stable RTP and its ΔI_p was proportional to the content of AFP-V. According to the facts above, a new affinity adsorption solid substrate-room temperature phosphorimetry (AA-SS-RTP) for the determination of trace AFP-V by Con A labeled with Triton X-100-4G-D was established. Detection limits of this method were 0.23 fg spot⁻¹ (direct method, corresponding concentration: 5.8 × 10⁻¹³ g mL⁻¹) and 0.13 fg spot⁻¹ (sandwich method, corresponding concentration: 3.2 × 10⁻¹³ g mL⁻¹). It has been successfully applied to determine the content of AFP-V in human serum and forecast human diseases, for its high sensitivity, long RTP lifetime, good repeatability, high accuracy and little background perturbation with at the long wavelength area. Meanwhile, the mechanism for the determination of trace AFP-V using AA-SS-RTP was also discussed.     

三磺化酞菁在微乳液、胶束、醇-水体系中的二聚现象研究

本文采用分光光度法研究了三磺化酞菁(S3Pc)在微乳液(Triton X-100-壬烷-正戊醇-水)、胶束(Triton X-100)、醇(甲、乙、丙醇)-水体系中的二聚现象。计算了S3Pc的二聚常数Kd。结果表明, S3Pc的Kd随着微乳液、胶束中表面活性剂的浓度的增加而减小; 随着醇-水溶液的羟基摩尔浓度(Mo-h)的增加而增加。     

Uranium micelle-mediated extraction in acetate medium: factorial design optimization

A micelle-mediated extraction (CPE) procedure has been developed to remove trace amounts of uranium from wastewater using a non-ionic surfactant (Triton (X-100)) and lipophilic chelating extracting agent (D2EHPA) in acetate medium. The methodology used is based on the formation of metal complexes soluble in a micellar phase of a non-ionic surfactant. The uranyl ions complexes are then extracted into the surfactant-rich phase at a ambient temperature. The effects of different operating parameters such as the concentrations of Triton (X-100), D2EHPA and metal ions, temperature, sodium acetate rate and pH on the cloud point extraction of uranyl ions were studied in details and a set of optimum conditions were obtained. The results showed, without contribution of energy (ambient temperature), that up to 1000?ppm of uranyl ions can quantitatively be removed (>97?%) in a single CPE extraction using optimum conditions.     

浊点萃取-分光光度法测定自来水及酒类样品中的痕量铁

利用非离子表面活性剂TritonX-100在温度高于其浊点时形成相分离行为,建立了浊点萃取-分光光度法测定痕量铁的新方法,探讨优化了以KSCN为显色剂,TritonX-100浊点萃取富集痕量铁的实验条件.研究发现:加入正辛醇可使TritonX-100的浊点降低约30℃,有利于萃取实验的进行;同时,加入的正辛醇与TritonX-100对痕量铁起到了协同萃取作用.在优化了的实验条件下,进行了痕量铁的分析,检出限为0.02mg·L-1,加标回收率为97.4%～101.6%,应用于自来水及酒类样品中痕量铁的测定,结果满意.