不同主体双发光层白色有机电致发光器件的性能研究

制备了结构为ITO/NPB/CBP:TBPe:rubrene/BAlq:Ir(piq)₂(acac)/BAlq/Alq₃/Mg:Ag的白色磷光有机电致发光器件.利用两种不同的主体材料,即用双载流子传输型主体材料CBP掺杂荧光染料TBPe及rubrene作为蓝光和橙黄光发光层;用电子传输型主体材料BAlq掺杂磷光染料Ir(piq)₂(acac)作为红色发光层.以上双发光层夹于空穴传输层NPB与具有电子传输性的阻挡层BALq之间.讨论了如何控制 关键词： 有机电致发光 磷光染料 掺杂 白光     

以蓝色发光材料DPVBi为基质的白色发光器件

白色有机发光器件是实现彩色平板显示的重要方案之一。利用蓝色发光材料DPVBi[4，4′—(2，2—苯乙烯基)—1，1′—联苯]掺杂红光染料DCJTB[4—氰甲烯基—2—叔丁基—6—(1，1，7，7—四甲基久洛尼定基—9—烯炔基—4H—吡喃)]作发光层制备了白色发光器件。研究了DPVBi掺杂不同浓度IDCJTB薄膜的光致发光性质，根据光致发光结果，制备了以DPVBi掺杂不同浓度DCJTB作发光层的电致发光器件，其结构为ITO／GuPc／NPB／DPVBi：DCJTB／Alq3／LiF／Al。当DCJTB质量分数为0．0008时，器件实现了白色发光(色度x=0．25，y=0．32)，电致发光和光致发光的掺杂比例基本相符，表明器件的白色发光主要是由基质DPVBi向掺杂剂DCJTB的能量传递产生的。研究还发现：白色器件随电压升高，光谱中蓝色成分相对于红色成分的比例略有增加，文章对此现象进行了分析。该白光器件在14V时达到最高亮度7822cd／cm^2，在20mA／cm^2电流密度下的亮度为-489cd／cm^2，最大流明效率为1．75lm／W。     

一种多层白色磷光有机电致发光器件的制备及性能研究

制备了一种结构为ITO/NPB/NPB:Ir(piq)₂(acac)/CBP:TBPe/BAlq:rubrene/BAlq/Alq₃/Mg:Ag的白色磷光有机电致发光器件.其中空穴传输型主体NPB掺杂磷光染料Ir(piq)₂(acac)作为红色发光层,双载流子传输型主体4,4′-N,N′-dicarbazole-biphenyl (CBP)掺杂TBPe作为蓝色发光层,电子传输型主体材料BAlq掺杂rubrene作为绿色发光层.以上发光层夹于 关键词： 电致发光 磷光染料 异质结 白光     

利用复合色彩转换膜实现白色有机电致发光

利用蓝色有机发光二极管激发荧光色彩转换膜的方法,制备了一种新型的白色有机电致发光器件.蓝色有机发光二极管的发光层采用在4,4′-Bis(carbazol-9-yl)biphenyl(CBP)主体中掺杂高效蓝色荧光染料N-(4-((E)-2-(6-((E)-4-(diphenylamino)styryl)naphthalen-2-yl)vinyl)phenyl)-N-phenylbenzenamine (N-BDAVBi)来制备.有机/无机复合色彩转换膜是将有机荧光颜料VQ-D25和无机荧光粉钇铝石榴石(YAG)按一定的重量比均匀分散到-[CH3CH2COOCH3]n- (PMMA)中经涂敷、固化而成.通过与单纯有机或无机色彩转换膜的比较及调整复合转换膜本身的厚度和荧光颜料的掺杂比例来优化白光器件的发光光谱,获得了色稳定性较高的白色有机电致发光器件.当驱动电压由6 V升至14 V时,器件的色坐标仅在(0.354,0.304)和(0.357,0.312)之间变化,其最高电流效率约为5.8 cd/A(4.35 mA/cm2),最高亮度为16 800 cd/m2(14 V).     

利用复合色彩转换膜实现白色有机电致发光

利用蓝色有机发光二极管激发荧光色彩转换膜的方法,制备了一种新型的白色有机电致发光器件.蓝色有机发光二极管的发光层采用在4,4′-Bis(carbazol-9-yl)biphenyl(CBP)主体中掺杂高效蓝色荧光染料N-(4-((E)-2-(6-((E)-4-(diphenylamino)styryl)naphthalen-2-yl)vinyl)phenyl)-N-phenylbenzenamine(N-BDAVBi)来制备.有机/无机复合色彩转换膜是将有机荧光颜料VQ-D25和无机荧光粉钇铝石榴石(YAG)按一定的重量比均匀分散到-[CH3CH2COOCH3]n-(PMMA)中经涂敷、固化而成.通过与单纯有机或无机色彩转换膜的比较及调整复合转换膜本身的厚度和荧光颜料的掺杂比例来优化白光器件的发光光谱,获得了色稳定性较高的白色有机电致发光器件.当驱动电压由6V升至14V时,器件的色坐标仅在(0.354,0.304)和(0.357,0.312)之间变化,其最高电流效率约为5.8cd/A(4.35mA/cm2),最高亮度为16800cd/m2(14V).     

基于连续性掺杂的高效全荧光白色有机电致发光器件的研究

利用荧光材料PT-01, PT-86, PT-05作为黄色荧光客体, 蓝色荧光客体以及荧光母体制备了一种基于连续性掺杂结构的全荧光白光有机电致发光器件. 其发光层为主体/客体薄层/主体/客体薄层···交替蒸镀的重复单元. 通过优化发光层中主体的厚度并检测发光层中单线态激子的分布, 将黄、蓝两种客体染料生长在发光层中适当的位置, 得到了高效且光谱稳定的全荧光白光器件. 其最大电流效率为11.2 cd/A, 亮度在159–20590 cd/m²范围内色坐标仅有(±0.004,±0.005)的改变. 基于这种连续性掺杂结构制备的器件, 其性能不但可以达到传统主-客体共掺结构所制备的器件的性能,而且具有较高的可重复性, 更适合产业化大批量生产. 关键词： 白色有机电致发光器件 连续性掺杂 能量转移 可重复性     

三元铱配合物磷光体系的白光有机电致发光器件光谱特性研究

将黄光磷光材料bis[2-(4-tertbutylphenyl)benzothiazolato-N,C2’]iridium (acetylacetonate) [(t-bt)₂Ir(acac)]超薄层作为黄光发光层,两个蓝光磷光染料iridium(Ⅲ) bis(4’,6’-difluorophenylpyridinato)tetrakis(1-pyrazolyl)borate (FIr6)和bis[(4,6-difluorophenyl)-pyridinato-N,C2’](picolinate) iridium (Ⅲ) (FIrpic)掺杂层作为蓝光发光层,制备了三元发光层的白光有机电致发光器件。该器件具有三元磷光染料分子协同发光特性,并且利用合适厚度的隔层,将三线态激子束缚在各自激子复合区域内,获得了稳定电致发光光谱,CIE色坐标为(0.29±0.01, 0.34±0.01),处于理想的白光区域。通过器件电学特性的测试,验证了磷光染料在三元发光层器件中电致发光作用的机理,同时结果表明,三元发光层器件由于稳定的激子复合区域而有效减弱了器件效率滚降现象。     

基于红色荧光染料3-(dicyanomethylene)-5, 5-dimethyl-1-(4-dimethylamino-styryl) cyclohexene的高性能白色有机电致发光器件

研究了基于红色荧光染料3-（dicyanomethylene）-5, 5-dimethyl-1-（4-dimethylamino-styryl） cyclohexene（DCDDC）的白色有机电致发光器件的性能,分别制备了基于DCDDC超薄层和DCDDC掺杂主体材料的两种器件结构: 1）indium-tin oxide（ITO）/N, N′-diphenyl-N, N′-bis（1-naphthyl-pheny1）-1, 1′-biphenyl-4, 关键词： 有机电致发光器件 白色发光 红色荧光染料 掺杂     

TBPe作蓝光材料的双层白色有机电致发光器件的性能

选用一种新型高效的蓝光有机小分子荧光染料TBPe,首次制备了以PVK:TBPe为蓝光发光层和Alq₃:rubrene为橙红光发光层的双层白光有机电致发光器件,器件结构为ITO/PVK:TBPe/Alq₃:rubrene/Mg:Ag。通过适当调节各有机层的掺杂比例和厚度,得到了发光性能比较理想的白光器件。器件在7V左右启亮,而且随着外加电压的变化,色坐标基本保持不变,在外加驱动电压为16V时,器件的亮度为738cd/m²,外量子效率为0.2%。我们还尝试选用本身可以发绿白光,而且兼具电子传输特性的母体材料Zn(BTZ)₂替代Alq₃,器件的最大亮度提高到1300cd/m²,色坐标为(0.32,0.36),更加接近白色等能点,器件其他光电性能也得到了显著地提高。     

基于双极传输母体的高效有机磷光发光器件

将红、绿、蓝3种不同颜色的染料分别掺杂到相同的母体材料2,7-二（二苯基磷酰）-9-（4-二苯基胺）苯基-9-苯基芴（POAPF）中,制得了可发3种颜色光的高效率有机电致发光器件。进一步将两种互为补偿色的发光材料以合适的掺杂浓度掺到POAPF中,制得了高效率白光器件。该白光器件采用了单发光层结构,器件电致发光光谱稳定性好,随驱动电压变化较小。4种不同颜色的发光器件的最大功率效率分别为16.50,43.72,29.78,32.83 lm/W。     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.     

A stereo matching algorithm using multi-peak candidate matches and geometric constraints

Gray cross correlation matching technique is adopted to extract candidate matches with gray cross correla- tion coefficients less than some certain range of maximal correlation coefficient called multi-peak candidate matches. Multi-peak candidates are extracted corresponding to three closest feature points at first. The corresponding multi-peak candidate matches are used to construct the model polygon. Correspondence is determined based on the local geometric relations between the three feature points and the multi-peak candidates. The disparity test and the global consistency checkout are applied to eliminate the remaining ambiguous matches that are not removed by the local geometric relational test. Experimental results show that the proposed algorithm is feasible and accurate.