Mesh phases in a ternary nonionic surfactant, oil, and water system

The binary system of hexaethylene glycol n-hexadecyl ether (C16EO6) and water (2H2O) has a complex, temperature-dependent lyotropic phase sequence, in the concentration region of 48-62 wt %. On cooling it shows the sequence lamellar phase, L(alpha), random mesh phase Mh1(0), rhombohedral mesh phase, Mh1(R(-)3m), bicontinuous cubic phase, V1(Ia(-)3d), and a two-phase hexagonal region, H1+Lbeta. On heating from the latter two-phase region the phase sequence is V1(Ia(-)3d), ,Mh1(0), and Lalpha. Polarizing optical microscopy, 2H nuclear magnetic resonance, and small-angle X-ray scattering have been used to study the stability of these phases, their sequence, and their physical parameters with the addition of the oils, 1-hexene, decane, and octadecane. The oils are located within the alkyl chain regions of the mesophase structures. Depending on whether the added oil is "penetrating" or "swelling", it may reside in the region between the C16 alkyl chains of the surfactant or at the center of the bilayer and affect phase stability. Oils affect both the volume of the alkyl chain region (at fixed surfactant water mole ratio) and the rigidity of the interfacial region. Both effects can influence the phase structures and their ranges of stability. Adding different types of oil to the mesh phases gives an opportunity to understand the factors that are important in their formation. The transition from the Mh1(R(-)3m) phase to Mh1(0) phase is triggered by the hydrocarbon region swelling to a critical volume fraction of 0.32, a surfactant rod radius of approximately 1.75 nm, and a critical water layer thickness of approximately 2.5 nm. The latter is most likely responsible for a weakening of the interlayer headgroup overlap interaction and the loss of correlation between the layers. The lamellar phase becomes the only stable phase at high oil content.     

Elongational flow induced ordering in surfactant micelles and mesophases

We have used small angle neutron scattering, SANS, to investigate the elongational flow induced ordering in surfactant micelles and mesophases. Spatially resolved SANS measurements have been used to determine the distribution of orientational ordering over the flow velocity pattern in an elongational flow cell, and comparison with the effects of shear flow are made. Two different surfactant systems have been studied, the charged wormlike mixed micelles of hexaethylene monododecyl ether, C16E6/hexadecyl trimethylammonium bromide, C16TAB (3% C16E(6)/5 mol% C16TAB), and the Lalpha lamellar phase of C16E6 (50.6 wt% C16E6 at 55 degrees C), and a substantially different response is observed. The orientational distribution of the Lalpha lamellar phase of C16E6 reflects the flow velocity pattern distribution within the cell, whereas for the wormlike mixed micelles of C16E6/C16TAB this is not the case, and this is associated with the shear thinning behavior of that system.     

Microstructure and rheological properties of liquid crystallines formed in Brij 97/water/IPM system

The phase diagram of Brij 97/water/IPM systems was determined at 25 degrees C. Rich liquid crystalline phases including Lalpha, H1, and cubic Fd3m phases were identified by means of small angle X-ray scattering (SAXS). Microstructure transitions of liquid crystals with changes in surfactant concentration and oil content are explained qualitatively by the surfactant packing parameter (vL/aSlc). Dynamic rheological results indicate that all three kinds of liquid crystals investigated show high elasticity. The lamellar, Lalpha, phases formed in Brij 97/water with two different oils, oleic acid and geraniol, were also studied in comparison with those of Brij 97/water/IPM systems. The strength of the network of lamellar phases formed in Brij 97/water/oleic acid and Brij 97/water/geraniol systems are appreciably stronger than for Brij 97/water/IPM systems, indicated by the smaller area of surfactant molecules at the interface and the higher moduli (G' and G').     

Phase behavior of 1-alkylpyridinium octane-1-sulfonates. effect of the 1-alkylpyridinium counterion size

The temperature-versus-composition phase diagrams of eight different 1-alkylpyridinium octane-1-sulfonates (APOSs) in water were studied by 1H NMR, 2H NMR, pulsed gradient spin-echo NMR, small-angle X-ray diffraction, differential scanning calorimetry, surface tension and conductivity measurements, and polarizing microscopy. The number of carbons (n(c)) in the hydrocarbon chain of the pyridinium counterions was varied from n(c) = 1 to n(c) = 8 to study how the phase behavior of the APOS/2H2O systems was affected by a change in the chain length of the counterion. The sodium octane-1-sulfonate (NaOS)/water system was used as a reference. This system formed an isotropic micellar solution (L1) phase and a normal hexagonal (H(I)) phase. All APOSs were readily soluble in water and formed L1 phases. The surface tension above the critical micelle concentration for n(c) between 1 and 3 was higher than that for NaOS, and it decreased steadily for the different APOSs with increasing chain length. The area per molecule at the air/solution interfaces was rather constant at 68 A2 for n(c) between 1 and 7. For 1-octylpyridinium octane-1-sulfonate (OPOS), it was about 5 A2 smaller, which was just outside the estimated error. However, the smallest area was obtained for NaOS. At higher surfactant concentrations, liquid crystalline phases formed. Both cubic and H(I) phases were found for n(c) = 1 and 2, while for n(c) between 3 and 5 only an H(I) phase was observed. H(I) and lamellar liquid crystalline (Lalpha) phases formed for n(c) = 6 and 7. The only liquid crystalline phase found in the OPOS system was a Lalpha phase. The NaOS H(I) phase was the only liquid crystalline phase that showed a linear relation between the 2H2O NMR quadrupolar splitting (deltaW) and Xsurf/X(W), where Xsurf and X(W) are the mole fractions of surfactant and water. The OPOS lamellae were found to be much thinner than expected, indicating a defect lamellar structure. This was further supported by the behavior of the quadrupolar splitting ofdeuterated OPOS. The anomalous behaviors of the 2H2O NMR quadrupolar splitting observed in the Lalpha phases of 1-heptylpyridinium octane-1-sulfonate and OPOS were interpreted in terms of changes in the population of the water molecules residing in different sites combined with a continuous rearrangement of the lamellae surface with the possible development of holes. The appearances of the phase diagrams were discussed in terms of surfactant molecular geometry and the packing of the amphiphiles in the aggregates formed.     

2H NMR evidence for the formation of random mesh phases in nonionic surfactant-water systems

Random mesh phases share many common features with the classical lamellar phase in that they are layered phases; but crucially, they possess nonuniform interfacial curvature, since the lamellae are pierced by water-filled pores. The introduction of curvature into the lamellae has been posited as a transitional precursor for other lyotropic phases. In this paper, we show that simple 2H nuclear magnetic resonance (NMR) experiments provide strong indication for the formation of the random mesh phase and the NMR data correlate well with literature results from small-angle X-ray scattering. The thermal evolution of the recorded quadrupolar splitting (DeltanuQ) is monitored within the lamellar phase of two nonionic surfactants, C16E6 and C12E5, as the samples are cooled or heated, and a marked and reversible change in the evolution of DeltanuQ is observed. Data from heavy water and deuterium labeled surfactant show the same temperature dependence and consequently report on the same structural changes with temperature. The formation of the random mesh phase is quantified in terms of an effective order parameter that is unity in the classical lamellar phase and takes values of <1 in the random mesh phase, reaching 0.6 at lower temperatures.     

Phase polymorphism by mixing of poly(oxyethylene)-poly(dimethylsiloxane) copolymer and nonionic surfactant in water

The phase behavior of the water/poly(oxyethylene)-poly(dimethylsiloxane) copolymer (Si25C3EO51.6)/pentaoxyethylene dodecyl ether (C12EO5) ternary system has been studied. Both the silicone copolymer and the surfactant have equal volumes of hydrophilic and lipophilic parts; i.e., these are balanced amphiphiles. Although only a lamellar phase is observed in water-Si25C3EO51.6 and water-C12EO5 binary systems, a variety of liquid crystalline phases, including normal micellar cubic (I1), hexagonal (H1), bicontinuous cubic (V1), lamellar (L(alpha)), reverse bicontinuous cubic (V2), and reverse hexagonal (H2), are observed in the copolymer-rich region of the ternary phase diagram. The small C12EO5 molecules dissolve at the hydrophobic interface in the thick bilayer of the Si25C3EO51.6 L(alpha) phase occupying a large area of the total interface of the aggregates and modulate the curvature of the aggregates. Hence a variety of self-assembled structures are observed. In contrast, Si25C3EO51.6 is not dissolved in the thin bilayer of the C12EO5 lamellar phase (L'(alpha)). Hence, the C12EO5 L'(alpha) phase coexists with copolymer-rich L(alpha) and H2 phases. Consequently, small surfactant molecules are dissolved in a large silicone copolymer aggregate to induce a change in layer curvature, but a large copolymer molecule is hard to incorporate with surfactant aggregates.     

Phase behavior of a mixture of poly(isoprene)-poly(oxyethylene) diblock copolymer and poly(oxyethylene) surfactant in water

The phase behavior of a mixture of poly(isoprene)-poly(oxyethylene) diblock copolymer (PI-PEO or C250EO70) and poly(oxyethylene) surfactant (C12EO3, C12EO5, C12EO6, C12EO7, and C12EO9) in water was investigated by phase study, small-angle X-ray scattering, and dynamic light scattering (DLS). The copolymer is not soluble in surfactant micellar cubic (I1), hexagonal (H1), and lamellar (Lalpha) liquid crystals, whereas an isotropic copolymer fluid phase coexists with these liquid crystals. Although the PI-PEO is relatively lipophilic, it increases the cloud temperatures of C12EO3-9 aqueous solutions at a relatively high PI-PEO content in the mixture. Most probably, in the copolymer-rich region, PI-PEO and C12EOn form a spherical composite micelle in which surfactant molecules are located at the interface and the PI chains form an oil pool inside. In the C12EO5/ and C12EO6/PI-PEO systems, one kind of micelles is produced in the wide range of mixing fraction, although macroscopic phase separation was observed within a few days after the sample preparation. On the other hand, small surfactant micelles coexist with copolymer giant micelles in C12EO7/ and C12EO9/PI-PEO aqueous solutions in the surfactant-rich region. The micellar shape and size are calculated using simple geometrical relations and compared with DLS data. Consequently, a large PI-PEO molecule is not soluble in surfactant bilayers (Lalpha phase), infinitely long rod micelles (H1 phase), and spherical micelles (I1 phase or hydrophilic spherical micelles) as a result of the packing constraint of the large PI chain. However, the copolymer is soluble in surfactant rod micelles (C12EO5 and C12EO6) because a rod-sphere transition of the surfactant micelles takes place and the long PI chains are incorporated inside the large spherical micelles.     

Diffusion-diffusion correlation and exchange as a signature for local order and dynamics

We demonstrate the use of new two-dimensional nuclear magnetic resonance experiments in the examination of local diffusional anisotropy under conditions of global isotropy. The methods, known as diffusion-diffusion correlation spectroscopy and diffusion exchange spectroscopy, employ successive pairs of magnetic field gradient pulses, with signal analysis using two-dimensional inverse Laplace transformation. Diffusional anisotropy is measured for water molecules in a polydomain lamellar phase lyotropic liquid crystal, 40 wt % nonionic surfactant C10E3 (C10H21O(CH2CH2O)6H) in H2O.     

Hofmeister anion effect on aqueous phase behavior of heptaethylene glycol dodecyl ether

The aqueous phase behavior of heptaethylene glycol dodecyl ether (C12E7) was investigated in the presence of sodium salts of Cl-, I-, and ClO4-. Pseudo binary T-X phase diagrams were constructed for these mixtures by means of differential scanning calorimetry. The salting-out electrolyte NaCl expanded the Lalpha region toward higher temperatures and shrank the H1 region toward lower temperatures compared with the salt-free system. On the contrary, the salting-in electrolytes NaI and NaClO4 induced shrinkage of the Lalpha region and an expansion of the H1 phase. The influence of these salts on the mesophase regions was more pronounced for the Lalpha phase than for the H1 phase, and area of the Lalpha phase region decreased in the sequence of NaCl > none > NaI > NaClO4, consist with the Hofmeister series of the anions. This salt effect on the mesophase stability in aqueous nonionic surfactant mixture would be qualitatively interpreted in terms of the salt effect on the hydration of the polyoxyethylene chain in the surfactant molecules.     

Aggregation and phase behavior of a double-chain surfactant, N-dodecyl-N-octyl-N-methylamine oxide, as a function of the protonation degree

The phase sequence of the N-dodecyl-N-octyl-N-methylamine oxide (C12C8MAO)/HCl/water system with increasing apparent degree of protonation, X, defined as [HCl]/[C12C8MAO], has been studied. For a 100 mM concentration of C12C8MAO the following sequence of phases has been observed: L1/L2, L1/Lalpha/L2, L1/Lalpha, Lalpha, Lalpha/L2. The single-phase Lalpha region begins at X = 0.007 and ends at X = 0.35. The upper phase boundary, X*, depends strongly on the acid that is used for the protonation of the surfactant. It is shifted for increasing hydrophilicity of the acid to higher X values. For formic acid X* = 0.95, and for HBr X* = 0.05. A weakly protonated 1% solution of the surfactant is an iridescent Lalpha phase. Both unilamellar vesicles and multilamellar vesicles are observed in cryo transmission electron microscopy and freeze fracture transmission electron microscopy images in the Lalpha phase. The phase sequence with protonation differs from that of single-chain amine oxide surfactants. The synergism between the protonated and the nonprotonated species is very weak in the range X < X*, while the transition from the Lalpha phase to the Lalpha/L2 two-phase region is considered to be due to synergism. Little or no synergism is observed regarding the surface tension, but synergism does appear in the interfacial tension between decane and the aqueous solution. The viscoelastic properties of the vesicle/Lalpha phase resemble those of densely packed hard spheres. The effects of electric charge on the elastic property of the vesicles could be understood in terms of the osmotic pressure of the solutions. The interlamellar spacing evaluated by small-angle X-ray scattering showed a minimum around X approximately 0.1, which is interpreted as a result of two opposing contributions. One contribution is the suppression of undulation of bilayer membranes by introduction of electric charges, and the other comes from the increasing total bilayer thickness due to the increasing hydrogen bond formation with increasing X.     

Rheological and rheo-SALS investigation of the multi-lamellar vesicle formation in the C12E3/D2O system

Usually in nonionic surfactant aqueous systems of the C(n)E(m) type, a lamellar phase occurs over a wide temperature and concentration range. For some C(n)E(m) surfactants, multi-lamellar vesicle (MLV) formation has been observed when the lamellar phase is subjected to shear flow. This communication reports the shear flow behavior at different shear rate values of a C(n)E(m) (where "n" is 12 and "m" is 3) aqueous system at 34 °C. The typical transient viscosity behavior of the shear-induced MLV formation in C(12)E(3)/D(2)O at 50 wt% of surfactant has been observed. The MLV formation is confirmed by time-resolved rheo-small angle light scattering (SALS) experiments. The experimental data show an intermediate structure that has been attributed to a multi-lamellar cylinders (MLCs).     

Lateral phase separation gives multiple lamellar phases in a "binary" surfactant/water system: the phase behavior of sodium alkyl benzene sulfonate/water mixtures

We have examined the structure of the lamellar phase (Lalpha) that coexists with a micellar solution (L1) for a commercial sodium alkyl benzene sulfonate (LAS) mixed with water. The surfactant is a mixture containing C10-C13 alkyl chains, having all positional isomers of the benzene sulfonate group present except the 1-isomer. Unusually for ionic surfactants, the difference in compositions between the coexisting L1 and Lalpha phases is large (L1 = approximately 20 wt % LAS; Lalpha = approximately 65 wt %). The main technique employed was X-ray diffraction, supplemented by optical microscopy and differential scanning calorimetry (DSC). At ambient temperatures, the lamellar phase gives a single diffraction pattern with the main reflection (d) at approximately 32.5 A, whatever the composition. However, above 40 degrees C, the diffraction peak becomes broader and moves to higher d values. At higher temperatures still, several distinct and different diffraction peaks are observed, differing in detail according to composition. The largest d values (approximately 42-4 A) are observed for the lowest LAS concentrations, while the largest number of separate reflections (five) occurs for samples with approximately 44-50% LAS, both at the highest temperatures. Although there are some differences in the data between heating and cooling cycles, the d values return to the original value at low temperature. There are no observable transitions in DSC, nor is there any heterogeneity in the lamellar phase observable by microscopy. The data clearly indicate that there is some lateral separation of the different LAS isomers within the bilayers, which results in the formation of local lamellar regions having different surfactant compositions. This lateral phase separation may arise from the presence of an (electrostatic) attractive interaction, which gives rise to an upper consolute loop within the lamellar phase region of a pure LAS isomer. Similar mechanisms may occur in biological membranes and could be responsible for the occurrence of membrane lipid patches.     

Studies on dodecyl betainate in combination with its degradation products or with phosphatidyl choline-phase behavior and hemolytic activity

Surface active betaine esters contain a hydrolysable bond and give naturally occurring products (fatty alcohol and the amino acid betaine) on degradation. They are therefore interesting candidates for use as cationic surfactants in pharmaceutical applications. In this work the phase behavior of two systems of relevance for the utilization of dodecyl betainate as a pharmaceutical excipient is studied, namely dodecyl betainate/dodecanol/betaine hydrochloride/D2O and dodecyl betainate/phosphatidyl choline (PC)/ethanol/D2O. The techniques used for phase characterisation were 2H NMR measured on the solvent, small angle X-ray spectroscopy and optical microscopy. Dilute dodecyl betainate/PC dispersions were characterized using laser diffraction. It is shown that introduction of relatively small amounts of the hydrolysis products of dodecyl betainate, i.e., dodecanol and betaine (used in the form of betaine hydrochloride), has a strong effect on the phase behavior of the binary dodecyl betainate/D2O system. The degradation products change the average curvature of the surfactant film so that, instead of a hexagonal phase at concentrations above the micellar phase, a probably defective, lamellar phase seems to form. The dodecyl betainate/PC/ethanol/D2O system shows a large region of a highly swelling lamellar phase. Dispersions of dodecyl betainate/PC/ethanol in water can be prepared with low energy input; i.e., the preconcentrate can be regarded as a self-dispersing solution. Introduction of dodecyl betainate and its degradation products does not impair the ability of PC to form vesicles. Experiments for evaluating the toxicity of surface active betaine esters to erythrocytes were also performed. There are indications that the hemolytic activity of dodecyl betainate is lower than that of the stable surfactant tetradecyltrimethylammonium chloride, which has similar critical micelle concentration. A combination of dodecyl betainate and PC gives very low hemolytic activity.     

表面活性剂体系中电荷诱导的层状相向囊泡相的转化

向一种非离子表面活性剂LA070(英文名AlcoholC12-C16Poly(1-6)Ethoxylate)复配体系LA070/C8H17OH/H2O形成的层状相中加入离子型表面活性剂使其电荷化,在电荷诱导下,双分子层的曲率发生变化,闭合形成具有黏弹性的囊泡相.离子型表面活性剂的加入量增大到一定程度时,由于反离子的屏蔽作用,囊泡结构被破坏,溶液的黏弹性消失,澄清的溶液逐渐变混浊,然后分为两相.     

Barotropic phase transition between the lamellar liquid crystal phase and the inverted hexagonal phase of dioleoylphosphatidylethanolamine

The phase transition between the lamellar liquid crystal (Lalpha) phase and the inverted hexagonal (H(II)) phase of dioleoylphosphatidylethanolamine (DOPE) in aqueous NaCl solutions was observed by means of differential scanning calorimetry (DSC) under ambient pressure and light-transmittance technique under high pressure. The pressure dependence of the transition temperature (dT/dp) and the thermodynamic quantities for the Lalpha/H(II) transition were compared with those of another phase transition found in the DOPE bilayer membrane, which is the transition from the lamellar crystal (Lc) phase to the Lalpha phase. The dT/dp value of the Lalpha/H(II) transition was about 3.5 times as large as that of the Lc/Lalpha transition while the thermodynamic quantities were significantly smaller than those of the latter to the contrary. Comparing the enthalpy and volume behavior of the Lalpha/H(II) transition with that of the Lc/Lalpha transition, we concluded that the Lalpha/H(II) transition can be regarded as the volume-controlled transition for the reconstruction of molecular packing.     

Use of the ternary phase diagram of a mixed cationic/glucopyranoside surfactant system to predict mesostructured silica synthesis

Mixed surfactant systems have the potential to impart controlled combinations of functionality and pore structure to mesoporous metal oxides. Here, we combine a functional glucopyranoside surfactant with a cationic surfactant that readily forms liquid crystalline mesophases. The phase diagram for the ternary system CTAB/H(2)O/n-octyl-beta-D-glucopyranoside (C(8)G(1)) at 50 degrees C is measured using polarized optical microscopy. At this temperature, the binary C(8)G(1)/H(2)O system forms disordered micellar solutions up to 72 wt% C(8)G(1), and there is no hexagonal phase. With the addition of CTAB, we identify a large area of hexagonal phase, as well as cubic, lamellar and solid surfactant phases. The ternary phase diagram is used to predict the synthesis of thick mesoporous silica films via a direct liquid crystal templating technique. By changing the relative concentration of mixed surfactants as well as inorganic precursor species, surfactant/silica mesostructured thick films can be synthesized with variable glucopyranoside content, and with 2D hexagonal, cubic and lamellar structures. The domains over which different mesophases are prepared correspond well with those of the ternary phase diagram if the hydrophilic inorganic species is assumed to act as an equivalent volume of water.     

Triacylglycerol microemulsions stabilized by alkyl ethoxylate surfactants--a basic study. Phase behavior, interfacial tension and microstructure

As triacylglycerols are the main components of natural fats and oils their solubilization in the form of emulsions or microemulsions was of great interest within the last years. However, systematic studies of their properties along the classical lines of complex fluids science are still missing. In the present paper we focus on the phase behavior, the interfacial tension and the microstructure of systems of type H(2)O/NaCl-triacylglycerol-alkylpolyglycolether (C(i)E(j)). The interfacial tension between water and oil sigma(ab) is high in a microemulsion system containing triolein. Thus, one needs high surfactant mass fractions to formulate a single-phase microemulsion. We show that this is not only true for triolein, but also for saturated long-chained triacylglycerols. The determination of the amphiphilicity factor f(a) and the calculation of the bending rigidities of the amphiphilic film confirm that despite the fact that high surfactant mass fractions and high temperatures are needed to solubilize triolein in a system of type H(2)O/NaCl-triacylglycerol-alkylpolyglycolether (C(i)E(j)), this is still a microemulsion in the narrower sense.     

Ellipsometry studies of nonionic surfactant adsorption at the oil--water interface

In the presented study we have developed and implemented a methodology for ellipsometry measurements at liquid interfaces that makes it possible to determine the amount adsorbed without assumptions of refractive index or thickness of the adsorbed layer. It was demonstrated that this is possible by combined measurements from different aqueous phases, H(2)O and D(2)O, which were shown to have sufficiently different refractive indices. The methodology was tested by studying adsorption of two types of nonionic poly(ethylene glycol) alkyl ether surfactants, C(n)H(2)(n)(+1)(OC(2)H(4))(m)OH or C(n)E(m) at the decane--aqueous interface, where C(12)E(5) was adsorbed from the oil phase and C(18)E(50) from the aqueous phase. The observed plateau values of the adsorbed amounts were 1.38 and 0.93 mg/m(2) for C(12)E(5) and C(18)E(50), respectively, which is in agreement with the corresponding values of 1.49 and 1.15 mg/m(2) obtained from applying the Gibbs equation to interfacial tension data for the same systems. We will briefly discuss the adsorption behavior in relation to the molecular structure of the surfactant and the phase behavior of the oil--surfactant--aqueous systems in relation to our experimental results.     

Self-assembly of mixed anionic and nonionic surfactants in aqueous solution

We present the phase diagram and the microstructure of the binary surfactant mixture of AOT and C(12)E(4) in D(2)O as characterized by surface tension and small angle neutron scattering. The micellar region is considerably extended in composition and concentration compared to that observed for the pure surfactant systems, and two types of aggregates are formed. Spherical micelles are present for AOT-rich composition, whereas cylindrical micelles with a mean length between 80 and 300 ? are present in the nonionic-rich region. The size of the micelles depends on both concentration and molar ratio of the surfactant mixtures. At higher concentration, a swollen lamellar phase is formed, where electrostatic repulsions dominate over the Helfrich interaction in the mixed bilayers. At intermediate concentrations, a mixed micellar/lamellar phase exists.     

Formation of Cubic-Phase Microemulsions with Anionic and Cationic Surfactants at Equal Amounts of Oil and Water

The formation and microstructure of cubic phases were investigated in anionic and cationic surfactant-containing systems at 25 degrees C. In the system sodium dodecyl sulfate(SDS)-dodecyltrimethylammonium bromide(DTAB)-water, mixing of two surfactants shows the phase transition hexagonal phase (H(1))-->surfactant precipitate, accompanied by an obvious decrease in the cross-sectional area per surfactant in the rod micelles of the hexagonal liquid crystal. In the mixed systems brine(A)-dodecane(B)-SDS(C)-DTAB(D)-hexanol(E), the isotropic discontinuous cubic phase is formed from the H(1) phase at a low cationic surfactant weight fraction, Y=D/(C+D), and from the lamellar phase at high Y upon dilution with equal amounts of oil and brine, respectively. The minimum surfactant concentration to form the cubic phase decreases with increases both in cationic surfactant weight fraction Y from 0 to 0.30 and in hexanol weight fraction, W(1)=E/(C+D+E), accordingly. The maximum solubilization for oil of the cubic phase reaches 43 wt% at 14 wt% of mixed surfactants and alcohol. Copyright 2000 Academic Press.