Direct electrothermal atomic absorption spectrometry determination of nickel in sea water using multiple hot injection and Zeeman correction

Methods for the direct determination of Ni in sea water samples by ETAAS were developed using Zeeman effect background correction system (ZEBC) and a multi-injection technique. A mass of palladium nitrate of 2.5 mug (for an injection volume of 100 mul) was used as chemical modifier. The optimum pyrolysis and atomization temperatures were 1700 and 2100 degrees C, respectively. The characteristic mass (m(0)) and characteristic concentration (C(0)), precision and accuracy were studied for different injection volumes (20, 100 and 200 mul). For an injection volume of 100 mul (five 20 mul aliquot) of sample the accuracy analysis of different certified materials (saline and non saline water) was agreeable. The total time of the proposed procedure is 6 min. A m(0) and C(0) of 34.5 pg and 0.3 mug l(-1), respectively were obtained for this injection volume (100 mul). Finally, interferences from major and minor components of sea water was studied.     

Multielement electrothermal atomic absorption spectrometry: A study on direct and simultaneous determination of chromium and manganese in urine

A study was carried out on the direct determination of Cr and Mn in urine using simultaneous atomic absorption spectrometry (SIMAAS). The heating program conditions, the absorbance signal profiles, the influence of different chemical modifiers, and the urine sample volume delivery into the tube were optimized to perform the calibration with aqueous solutions. Among several chemical modifiers tested, the best recovery and repeatability results were obtained for 3 microg Mg(NO3)2. On using this modifier, the pyrolysis and atomization temperatures for simultaneous determination of Cr and Mn were 1,300 degrees C and 2,500 degrees C, respectively. Urine samples were diluted (1+1) with 2.0% (v/v) HNO3 + 0.05% (w/v) Triton X-100 prepared in high purity water. A 20-microL aliquot of analytical solution and 10 microL of chemical modifier solution were delivered to the graphite tube. The characteristic masses were 7.8 pg for Cr (RSD=4.0%) and 4.6 pg for Mn (RSD=2.6%). The limits of detection were 0.08 microg L(-1) (n=20, 3s) for Cr and 0.16 microg L(-1) (n=20, 3s) for Mn. Recovery studies for 1.0 or 2.5 microg L(-1) of Cr and Mn added to different urine samples showed acceptable results for Cr (100%, RSD=14%) and Mn (88%, RSD=5.6%).     

Multielement determination of cadmium and lead in urine by simultaneous electrothermal atomic absorption spectrometry with an end-capped graphite tube.

A method for the multielement determination of cadmium and lead in urine is proposed by simultaneous electrothermal atomic absorption spectrometry (SIMAAS) with an end-capped transversely heated graphite atomizer (EC-THGA). The best conditions for cadmium and lead determination were obtained in the presence of NH4H2PO4 as a chemical modifier, using 500 degrees C and 1800 degrees C as the pyrolysis and atomization temperatures, respectively. Urine samples were diluted 1 + 4 directly in autosampler cups with a mixture of 0.125% (w/v) Triton X-100 + 2.5% (v/v) HNO3 + 0.31% (w/v) NH4H2PO4. The optimized heating program was carried out in 57 s, and the instrument calibration was done with aqueous reference solutions. The use of EC-THGA increased the sensitivity of cadmium and lead by 14% and 25%, respectively. The detection limits (n = 20, 3delta) were 0.03 microg L(-1) (0.36 pg) for cadmium and 0.57 microg L(-1) (6.8 pg) for lead. The performance of EC-THGA was acceptable up to 500 heating cycles. The reliability of the entire procedure was checked with the analysis of a lyophilized urine certified reference material. The found concentrations were in agreement with the recommended values (95% confidence level).     

Direct determination of selenium in a wild fruit juice by electrothermal atomic absorption spectrometry

A matrix modifier composed of platinum and nickel is proposed for the determination of selenium in a wild fruit juice made from Lantingguo (Vuccinium uliginosam). Five matrix modifiers (copper/nickel, palladium/magnesium, platinum/magnesium, platinum/nickel and platinum/copper) for suppressing the interference effects of seven co-existing elements (potassium, phosphorus, calcium, magnesium, manganese, zinc and iron) in a wild juice were studied and a matrix modifier composed fro;m 10 mug of platinum and 200 mug of nickel was found to give the best performance. Selenium in three juices was determined by electrothermal atomic absorption spectrometry employing the proposed matrix modifier without matrix preseparation. The relative standard deviation was 14% for 0.20 mg l(-1) of selenium. The recoveries were 95-110%. A characteristic mass was 28 pg.     

Evaluation of ammonia as diluent for serum sample preparation and determination of selenium by graphite furnace atomic absorption spectrometry

A method for the determination of total selenium in serum samples by graphite furnace atomic absorption spectrometry was evaluated. The method involved direct introduction of 1:5 diluted serum samples (1% v/v NH₄OH+0.05% w/v Triton X-100^®) into transversely heated graphite tubes, and the use of 10 μg Pd+3 μg Mg(NO₃)₂ as chemical modifier. Optimization of the modifier mass and the atomization temperature was conducted by simultaneously varying such parameters and evaluating both the integrated absorbance and the peak height/peak area ratio. The latter allowed the selection of compromise conditions rendering good sensitivity and adequate analyte peak profiles. A characteristic mass of 49 pg and a detection limit (3s) of 6 μg 1⁻¹ Se, corresponding to 30 μg l⁻¹ Se in the serum sample, were obtained. The analyte addition technique was used for calibration. The accuracy was assessed by the determination of total selenium in Seronorm™ Trace Elements Serum Batch 116 (Nycomed Pharma AS). The method was applied for the determination of total selenium in ten serum samples taken from individuals with no known physical affection. The selenium concentration ranged between 79 and 147 μg l⁻¹, with a mean value of 114±22 μg l⁻¹.     

Determination of beryllium and selenium in human urine and of selenium in human serum by graphite-furnace atomic absorption spectrophotometry.

For human urine beryllium (Be), each sample (500 microl) was diluted (1+1) with Nash reagent (containing 0.2% (v/v) acetylacetone and 2.0 M ammonium acetate buffer at pH 6.0) and then a 20-microl volume of Triton X-100 (0.4%, v/v) aqueous solution was added. An aliquot (10 microl) of the diluted urine mixture was introduced into a graphite cuvette and was atomized according to a temperature program. The method detection limit (MDL, 3sigma) for Be was 0.37 microg/l in the undiluted urine sample and the calibration graph was linear up to 65.0 microg/l. Calibration graphs were prepared by the standard addition method. Accuracies of 98.6-102% were obtained when testing standard reference material (SRM 2670) freeze dried human urine samples. Precision (relative standard deviation, RSD) for urine Be was < or = 2.3% (withinrun, n = 5) and was < or = 3.0% (between-run, n = 3). For human urine and serum selenium (Se), samples (100 microl) were diluted with HNO3 (0.2%, v/v) to make a (1+1) dilution for urine analysis or a (1+4) dilution for serum analysis. An additional aliquot (10 microl) of Triton X-100 (0.1%, v/v) was added to each 200 microl of (1+1) diluted urine (or 20 microl of the Triton X-100 was added to each 500 microl of (1+4) diluted serum) sample. After the diluted sample mixture (10 microl) was introduced into a graphite cuvette, the corresponding chemical modifier (10 microl, containing Ni2+ + Pd + NH4NO3 in HNO3 (0.2%, v/v)) was added to it and the mixture was atomized. The MDL (3sigma) for Se in urine and in serum was 4.4 and 21.4 microg/l in undiluted sample, respectively, and the calibration graphs were linear up to 150 and 400 microg/l. Accuracies of urine Se were 98.9 - 99.4% by testing SRM 2670 (NIST) urine standards with RSD (between-run, n = 3) within 2.9%; and that of serum Se was 97.2% when testing a certified second-generation human serum (No. 29, #664) with RSD (between-run, n = 3) of 1.4%. The proposed method can be applied easily, directly, and accurately to the measurement of Be and Se in real samples (including six urine Se and four serum Se from patients of Blackfoot Disease in Taiwan).     

Comparison of four microwave digestion methods for the determination of selenium in fish tissue by using hydride generation atomic absorption spectrometry

Four microwave digestion methods of fish tissue for selenium determination by hydride generation atomic absorption spectrometry were compared, in which potassium hexacyanoferrate(III) was chosen as a masking agent for eliminating matrix interferences. The results showed that the methods employing HNO(3)/H(2)O(2), HNO(3)/K(2)S(2)O(8)/H(2)O(2) and HNO(3)/H(3)PO(4)/H(2)O(2) digestion media were unreliable. However, the decomposition using the digestion media of HNO(3)/H(2)SO(4)/H(2)O(2) enabled adequate digestion of fish tissue and retention of selenium in a state amenable for determination. Therefore, the digestion procedures with HNO(3)/H(2)SO(4)/H(2)O(2) media are proposed for the determination of selenium in fish tissue by hydride generation atomic absorption spectrometry. The recoveries of the spiked samples investigated ranged from 90 to 102%. The result obtained from analyzing the NIES CRM No. 6 mussel was in good agreement with the reference value (reference value: 1.5 mug/g; found: 1.45 +/- 0.05 mug/g). The limit of detection for selenium was 0.03 mug/g dry mass for a 100 mg sample. The contents of selenium in local fish species investigated ranged from 0.49 to 2.90 mug/g, and the relative standard deviation for the determination of selenium was less than 8%.     

Evaluation and application of bismuth as an internal standard for the determination of lead in wines by simultaneous electrothermal atomic absorption spectrometry

A method for the direct determination of Pb in wines by simultaneous multi-element atomic absorption spectrometry (SIMAAS) using a transversely heated graphite atomizer, Zeeman-effect background corrector and internal standardization is proposed. Bismuth was used as an internal standard and Pd(NO3)2 plus Mg(NO3)2 as chemical modifier to stabilize both the analyte and the internal standard. The implementation of two pyrolysis steps avoided any build-up of carbonaceous residues on the graphite platform. All diluted samples (1 + 1 v/v) in 0.2% v/v HNO3 and reference solutions (5.0-50 microg l(-1) Pb in 0.2% v/v HNO3) were spiked with 25 microg l(-1) Bi. For a 20 microl aliquot dispensed into the graphite tube, a good correlation (r = 0.9997) was obtained between the ratio of the analyte signal to the internal standard signal and the analyte concentration of the reference solutions. The electrothermal behaviour of Pb and Bi in red, white and rosé wines were compared. In addition, absorbance variations due to changes in experimental conditions, such as atomizer temperature, integration time, injected sample volume, radiation beam intensity, graphite tube surface, dilution and sample composition, were minimized by using Bi as internal standard. Relative standard deviations of measurements based on integrated absorbance varied from 0.1 to 3.4% and from 0.5 to 7.3% (n = 12) with and without internal standard correction, respectively. Good recoveries (91-104%) for Pb spikes were obtained. The characteristic mass was 45 pg Pb and the limit of detection based on integrated absorbance was 0.9 microg l(-1) Pb. Internal standardization increased the lifetime of the tube by 25%. Direct determinations of Pb in wines with and without internal standardization approaches were in agreement at the 95% confidence level. The repeatability and the tube lifetime were improved when using Bi as internal standard. The improvement in accuracy using an internal standard was only observed when the analytical results were affected by errors.     

Minimalism approach for determination of Cu, Fe and Zn in serum by simultaneous electrothermal atomic absorption spectrometry

Copper, iron and zinc were determined in serum by simultaneous atomic absorption spectrometry (SIMAAS). The minimalism approach was adopted throughout this analytical method, to reduce time, costs, sample, reagent, energy requirements, and residue production. Samples were 80-fold diluted with 0.01% (w/v) Triton X-100+1% (v/v) HNO₃ directly in the autosampler cups. Three strategies were implemented to match the final diluted analyte concentrations with the SIMAAS linear concentration ranges: a reduced 5 μl aliquot of analytical reference or diluted sample solution was introduced into the preheated graphite tube at 100 °C; a super-estimated pyrolysis temperature was chosen for selective zinc volatilization; and a mini argon flow of 50 ml min⁻¹ was used during the atomization step. The pyrolysis and atomization temperatures for the simultaneous heating program were 700 and 2300 °C, respectively. The characteristic masses for copper (26 pg), iron (16 pg), and zinc (2.7 pg) were estimated from the analytical graphs. The detection limits (n=20, 3σ) were 4.0, 2.2, and 0.4 μg l⁻¹ for copper, iron and zinc, respectively. The reliability of the entire procedure was checked with the analysis of Seronorm™ trace elements in serum (Sero AS). Serum samples of five volunteers were analyzed and the recovery tests for additions of 2.0, 2.0 and 1.0 mg l⁻¹ were 100±4, 99±6, and 95±5% for copper, iron and zinc, respectively.     

Determination of selenium in marine biological tissues by transverse heated electrothermal atomic absorption spectrometry with longitudinal Zeeman background correction and automated ultrasonic slurry sampling.

A fast, sensitive, and reliable method for determination of selenium in marine biological tissues by electrothermal atomic absorption spectrometry with slurry sampling was developed. Slurries were prepared from fresh and frozen seafood samples that were previously homogenized, dried, and ground; particle sizes <100 microm were taken for analysis. A 3% (v/v) HNO3 solution containing 0.01% (v/v) Triton X-100 was used as slurry diluent. Slurries were mixed on an automated ultrasonic slurry sampler at 20% amplitude for 30 s just before an aliquot was injected into the furnace. The method was successfully validated against the following certified reference materials: NRCC CRM DORM-2 (Dogfish muscle); NRCC CRM TORT-2 (Lobster hepatopancreas); NRCC CRM DOLT-2 (Dogfish liver); and BCR CRM 278 (Mussel tissue), and was subsequently applied to determination of Se in 10 marine biological samples. The influences of the drying procedure (oven-, microwave-, and freeze-drying), matrix modifier amount, mass of solid material in cup, and pipetting sequence are discussed. The limit of determination of Se was 0.16 microg/g and the repeatability, estimated as between-batch precision, was in the range of 4-8%. Se contents in the samples ranged from 0.6 to 2.8 microg/g. The proposed method should be useful for fast assessment of the daily dietary intake of Se.     

Microwave digestion of fish tissue for selenium determination by differential pulse polarography

In KIO(3)NH(3)NH(4)Cl medium, the selenium complex Se(O)SO(2-)(3), resulted from the reaction of selenite and sulphite in acid solution, gave a catalytic wave, which was applied to the determination of selenium in fish by differential pulse polarography. The sample was decomposed using the HNO(3)/H(2)SO(4)/H(2)O(2) digestion mixture in a closed PTFE digestion vessel with microwave heating. The detection limit was 0.06 mug/dm(3). The calibration curve was linear up to 8 mug/dm(3). Selenate present was reduced with hot hydrochloric acid to selenite. The recoveries of the selenite and selenate in two spiked samples investigated ranged from 91 to 104%. The NIES CRM No. 6 mussel was analyzed and the results obtained agreed well with the reference value (reference value: 1.5 mug/g; found: 1.43 +/- 0.05 mug/g). The results obtained by differential pulse polarography were in good agreement with those found by hydride generation atomic absorption spectrometry.     

Effectiveness of palladium as a chemical modifier for direct silver and manganese determination in cocaine and heroin by electrothermal atomic absorption spectrometry

Methods for the direct determination of silver and manganese in cocaine and heroin by electrothermal atomic absorption spectrometry using palladium as chemical modifier have been developed. Cocaine samples, 0.5 g, were dissolved in 2 ml of 35.0% (m/v), HNO(3) diluting to 10 ml with ultrapure water. A comparative study of palladium, magnesium nitrate, palladium-magnesium nitrate and nitric acid used as chemical modifiers was carried out, and it was found that palladium alone is adequate to stabilize silver and manganese at charring temperatures of 1000 and 1300 degrees C respectively. A study was made on the insertion of a cooling step before the atomization step, and this approach was not advantageous. Limits of detection of 2.3 and 6.9 microg kg(-1) were obtained for silver and manganese respectively. The analytical recovery oscillated between 95.9 and 103.6% for silver and between 99.7 and 103.0% for manganese. Finally, a study of some interferences and a study of the precision and analytical recovery of the amount of sample were also carried out.     

Determination of selenium in ores, concentrates and related materials by graphite-furnace atomic-absorption spectrometry after separation by extraction of the 4-nitro-o-phenylenediamine complex

A method for determining approximately 0.01 mug/g or more of selenium in ores, concentrates, rocks, soils, sediments and related materials is described. After sample decomposition selenium is reduced to selenium(IV) by heating in 4M hydrochloric acid and separated from the matrix elements by toluene extraction of its 5-nitropiazselenol complex from approximately 4.2M hydrochloric acid. After the extract has been washed with 2% nitric acid to remove residual iron, copper and chloride, the selenium in the extract is oxidized to selenium(VI) with 20% bromine solution in cyclohexane and stripped into water. This solution is evaporated to dryness in the presence of nickel, and selenium is ultimately determined in a 2% v/v nitric acid medium by graphite-furnace atomic-absorption spectrometry at 196.0 nm with the nickel functioning as matrix modifier. Common ions, including large amounts of iron, copper and lead, do not interfere. More than 1 mg of vanadium(V) and 0.25 mg each of platinum(IV), palladium(II), and gold(III) causes high results for selenium, and more than 1 mg of tungsten(VI) and 2 mg of molybdenum(VI) causes low results. Interference from chromium(VI) is eliminated by reducing it to chromium(III) with hydroxylamine hydrochloride before the formation of the selenium complex.     

Slurry sampling graphite furnace atomic absorption spectrometry: determination of trace metals in mineral coal

A procedure for lead, cadmium and copper determination in coal samples based on slurry sampling using an atomic absorption spectrometer equipped with a transversely heated graphite tube atomizer is proposed. The slurries were prepared by weighing the samples directly into autosampler cups (5-30 mg) and adding a 1.5 ml aliquot of a diluent mixture of 5% v/v HNO(3), 0.05% Triton X-100 and 10% ethanol. The slurry was homogenized by manual stirring before measurement. Slurry homogenization using ultrasonic agitation was also investigated for comparison. The effect of particle size and the use of different diluent compositions on the slurry preparation were investigated. The temperature programmes were optimized on the basis of pyrolysis and atomization curves. Absorbance characteristics with and without the addition of a palladium-magnesium modifier were compared. The use of 0.05% m/v Pd and 0.03% m/v Mg was found satisfactory for stabilizing Cd and Pb. The calibration was performed with aqueous standards. In addition, a conventional acid digestion procedure was applied to verify the efficiency of the slurry sampling. Better recoveries of the analytes were obtained when the particle size was reduced to <37 mum. Several certified coal reference materials (BCR Nos. 40, 180, and 181) were analyzed, and good agreement was obtained between the results from the proposed slurry sampling method and the certificate values.     

Comparison of chemical modifiers for selenium determination in soil aqua regia extracts by ZETAAS

The effect of various chemical modifiers 0.5 g l⁻¹ Pd, 1% (w/v) Ni, 0.5 g l⁻¹ Pd + 1% (w/v) Ni and 1.0 g l⁻¹ Pd on the measurement of selenium in soil aqua regia extracts, by ZETAAS, is described. Two Certified Reference Materials (CRMs) RTC-CRM 023-050 and RTC-CRM 025-050 were used for this study. Pyrolysis and atomization curves were obtained for each chemical modifier and their optimal values were assessed. By using standard addition as calibration method, accurate results were obtained for all the chemical modifiers studied. The precision was similar for both CRMs, with a maximum value of 7.5% R.S.D. The limits of detection and quantification for selenium in the soil extracts (n = 10) were 3.0 and 6.0 μg l⁻¹, respectively. The characteristic mass of selenium is assessed as 10 pg. The use of aqua regia as extractant gave quantitative results for selenium in the CRMs assayed.     

Determination of traces of chromium in cocaine and heroin by flameless atomic absorption spectrometry

A method for the determination of total chromium in cocaine and heroin by flameless atomic absorption spectrometry is presented. Cocaine samples were dissolved in 2 ml of HNO(3) 35.0% (v/v) and diluted to 10 ml with ultrapure water; heroin samples were dissolved in ultrapure water, adding 0.4 ml of HNO(3) 35.0% (v/v) to dissolve inert species, and also diluted to 10 ml. Mg(NO(3))(2) and HNO(3), as chemical modifiers, were compared in terms of sensitivity, precision and accuracy, a lower detection limit being obtained for the use of Mg(NO(3))(2), 5.77 mug kg(-1) (7.23 mukg(-1) for HNO(3)). Within-batch precision was found to be 6.19% and 1.48% for drug solution spiked with 0 and 10 mug l(-1) of Cr(3+), respectively, when using Mg(NO(3))(2), and 7.45 and 1.19% for the same respective concentration levels when using HNO(3). Similar results on analytical recovery were obtained for both Mg(NO(3))(2) and HNO(3). Mg(NO(3))(2) was selected as the more adequate of the two chemical modifiers. A study of the introduction of a cooling-down step of 50 degrees C was carried out and compared in terms of sensitivity to the programme without a cooling-down step, but no advantage was observed. Studies on the variation in precision and analytical recovery with the amount of sample, and interferent effects of different species on chromium determination were developed. Finally, chromium concentrations obtained in cocaine samples varied between 0.02 and 0.14 mg kg(-1), the levels in the heroin samples being in the 0.05-0.59 mg kg(-1) range.     

Direct determination of boron in a cobalt-based alloy by graphite furnace-atomic absorption spectrometry

A matrix modifier composed of nickel and zirconium, and a graphite tube treated with zirconium solution were proposed for the determination of boron in cobalt-based alloys by graphite furnace-atomic absorption spectrometry. The effects of this matrix modifier and the treated graphite tube were studied, and the combination of 60 mug of nickel and 20 mug of zirconium as matrix modifier, and a graphite tube soaked with 10 g 1(-1) of zirconium solution were found to give the highest analytical sensitivity. The interference effects of major components (cobalt) and eight minor components (chromium, nickel, tungsten, iron, tantalum, molybdenum, titanium, aluminium and manganese) were studied. Boron in four cobalt-based alloys was determined by graphite furnace-atomic absorption spectrometry employing the proposed matrix modifier and the treated graphite tube, without the preseparation of matrix. The relative standard deviation was 3.3% for 0.048% of boron. A characteristic mass was 500 pg.     

Copper determination in biological materials by ETAAS using W-Rh permanent modifier

A tungsten-rhodium treatment on the integrated platform of a transversely heated graphite atomiser was used as a permanent chemical modifier for the determination of copper in biological materials by using digested samples as well as slurry sampling in electrothermal atomic absorption spectrometry. The W-Rh permanent modifier was as efficient as Pd+Mg(NO(3))(2) conventional modifier for obtaining good Cu thermal stabilisation in the digested and slurry samples. The permanent W-Rh modifier remained stable by approximately 300 and 250 firings when 20 mul of digested sample and 20 mul of slurry were delivered into the atomiser, respectively. In addition, the permanent modifier increased the tube lifetime up to 1370 and 744 analytical measurements in the digested and slurry samples, respectively. Also, when the W-Rh permanent modifier was employed, there was less variation of the slope of the analytical curves during the total atomiser lifetime, resulting in a decreased need of re-calibration during routine analysis, increasing the sample throughput, and consequently diminishing the variable analytical costs. Detection limits obtained with W-Rh permanent modifier were 0.64 and 0.33 mug g(-1) Cu for digested (dilution factor 100 ml g(-1)) and 1.0% m/v slurries of biological materials, respectively. Results for the determination of copper in the samples were in agreement with those obtained with decomposed sample solutions by using Pd+Mg(NO(3)), since no statistical differences were found after applying the paired t-test at the 95% level.     

Electrothermal atomic absorption spectrometric determination of cadmium and lead with stabilized phosphate deposited on permanently modified platforms

Some drawbacks of the phosphate modifier such as reagent blank contribution and background absorption in electrothermal atomic absorption spectrometric determination of cadmium and lead are substantially alleviated by application of small amounts of phosphate, approximately 0.2 mumol (25 mug of NH(4)H(2)PO(4) or (NH(4))(2)HPO(4)), on the integrated platform of transversely heated graphite atomizer pre-treated with 2.7 mumol of Zr (250 mug) or W (500 mug) and 0.1 mumol of Ir (20 mug). Pyrolysis temperatures for Cd and Pb are up to 900 and 1100 degrees C for aqueous solutions and within 400-600 degrees C (Cd) and 750-850 degrees C (Pb) for biological fluids (urine, blood) and tissues (hair, liver, muscle) solubilized with tetraethylammonium hydroxide. The thermally stabilized phosphate on Zr-Ir or W-Ir treated platforms serves as a permanent modifier in analyses of environmental waters by multiple hot injections of large sample aliquots. Applications to water and biological certified reference materials are tabulated and show good agreement with certified values. Characteristic masses are 0.7-1.0 pg for Cd and 26-31 pg for Pb.     

Chemical modifiers for direct determination of cobalt in coal combustion residues by ultrasonic slurry-sampling-ETAAS

Five modifiers were tested for the direct determination of cobalt in coal fly ash and slag by ultrasonic slurry-sampling electrothermal atomic absorption spectrometry (USS-ETAAS).The furnace temperature programs and the appropriate amount for each modifier were optimized to get the highest signal and the best separation between the atomic and background signals. Nitric acid (0.5% v/v) was the most adequate chemical modifier for cobalt determination, selecting 1,450 degrees C and 2,100 degrees C as pyrolysis and atomization temperatures, respectively. This modifier also acts as liquid medium for the slurry simplifying the procedure. The remaining modifiers enhanced the background signal, totally overlapped with cobalt peak. The method optimized gave a limit of detection of 0.36 microg g(-1), a characteristic mass of 13 +/- 1 pg and an overall-method precision which is highly satisfactory (<7%, RSD). The method was validated by analyzing two certified coal fly ash materials, and satisfactory recoveries were obtained (83-90%) and no statistical differences were observed between the experimental and the certified cobalt concentrations. Additionally, certified sediment, soil and urban particulate matter were assayed; again good results were obtained. The developed methodology was used to determine cobalt in several coal combustion residues from five Spanish power plants.