A flow-cell optosensor for lead based on immobilized dithizone

Dithizone immobilized on XAD-4 resin has been studied as a sensor element of an optical sensor for lead using a flow-cell. Using this arrangement, lead in solution has been determined in the concentration range 1 x 10(-5)-3 x 10(-7)M with a detection limit of 1 x 10(-8)M(i.e., 2 mug/l.). The standard deviation of the method for the measurement of lead at a concentration of 1 x 10(-6)M was found to be 7%. The response of the sensor was reproducible and can be regenerated using 0.01M hydrochloric acid followed by citrate-hydroxylamine solution.     

Urea potentiometric biosensor based on urease immobilized on chitosan membranes

Potentiometric biosensors based on urease (E.C. 3.5.1.5.) immobilized on chitosan membranes coupled to all-solid-state nonactin ammonium ion selective electrodes are described. The enzyme was immobilized on the chitosan membranes by four procedures: (A) adsorption; (B) adsorption followed by reticulation with dilute aqueous glutaraldehyde solution; (C) activation with glutaraldehyde followed by contact with the enzyme solution; and (D) activation with glutaraldehyde, contact with the enzyme solution and reduction of the Schiff base with sodium borohydride. The response characteristics of the biosensors obtained with these enzymatic membranes were determined and compared. The biosensor with best response characteristics, obtained by procedure (B), showed the following characteristics of response to urea: (i) linearity in the 10(-4) to 10(-2) M range; (ii) slope of up to 56 mV per decade; (iii) response time between 30 s and 2 min; and (iv) lifetime of 2 months. This biosensor was tested in the determination of urea in blood serum samples.     

Blood compatibility of thermoplastic polyurethane membrane immobilized with water-soluble chitosan/dextran sulfate

Water-soluble chitosan (WSC)/dextran sulfate (DS) was immobilized onto the surface of thermoplastic polyurethane (TPU) membrane after ozone-induced graft polymerization of poly(acrylic acid) (PAA). The surface was characterized with contact angle measurement and X-ray photoelectron spectroscopy (XPS). The adsorption of human plasma fibrinogen (HPF) followed the Langmuir adsorption isotherm. The results showed that the surface density of peroxides generated and poly(acrylic acid) (PAA) grafted reached the maximum value at 20 min of ozone treatment. It was found that the WSC- and DS-immobilized amount increased with pH and the molecular weight of WSC. The membrane/water interfacial free energy increased with PAA-grafting and WSC/DS-immobilization, indicating the increasing wettability of TPU membrane. The adsorption of HPF on TPU-WSC/DS membranes could be effectively curtailed and exhibited unfavorable adsorption. Moreover, WSC/DS immobilization could effectively reduce platelet adhesion and prolong the blood coagulation time, thereby membrane improving blood compatibility of TPU membrane. In addition, the in vitro cytotoxicity test of PEC modification was non-cytotoxic according to much low growth inhibition of L929 fibroblasts. Furthermore, TPU-WSC/DS membranes exhibited higher cell viability than native TPU membrane.     

Optical determination of L-tyrosine based on eggshell membrane immobilized tyrosinase

An optical biosensor based on the eggshell membrane immobilized tyrosinase is described for the detection of L-tyrosine (L-Tyr). The detection scheme was based on the measurement of absorption value of color adduct resulting from the reaction of 3-methyl-2-benzothiazolinone hydrazone and dopa-quinone produced from the enzymatic oxidation of L-Tyr. The prepared biosensor demonstrated optimum activity at pH 7, optimum temperature range of 20-40 degrees C and a linear response for the L-Tyr concentration in range of 5-200 microM. It also showed good operation stability for repeated measurements (over 300 times) and storage stability after it had been kept at 4 degrees C for 3 months.     

A membrane bioreactor with immobilized proteinase

A procedure was developed for layer-by-layer immobilization of terrilytin proteolytic enzyme on track membranes and flat-membrane blocks. The hydrolysis of fibrinogen and casein was studied, and the possibility of using such a structure as an enzymatic bioreactor was demonstrated.     

Protein adsorption and platelet adhesion of polysulfone membrane immobilized with chitosan and heparin conjugate

Polysulfone (PSF) membranes were treated with ozone to introduce peroxides, and then grafted with either acrylic acid or chitosan, followed by the immobilization of heparin. The effect of spacer arm on blood compatibility was investigated using three chitosans of different molecular weight [1170 (water soluble), 160 000, and 400 000] and similar degrees of deacetylation (75%). The hydrophilicity was evaluated by measuring the contact angle of water. Blood compatibility was evaluated using the activated partial thromboplastin time (APTT) as well as the adhesion of platelets. The protein affinity was determined by the absorption of human serum albumin (HSA) and human plasma fibrinogen (HPF). The results show that by the coupling of chitosan, the amount of heparin immobilized can be increased by four times. Water contact angle (from 78 ° to 41 °) decreased with the increase of the amount of heparin immobilized, showing increased wettability. The heparinized PSF membrane showed longer APTT and decreasing platelet adhesion, compared to that of unmodified PSF membrane. The adsorption of HSA and HPF were reduced to 17 and 6%, respectively. This suggests that longer spacer binding to heparin can increase the opportunity of anti‐coagulation on contacting blood. These results demonstrated that the hydrophilicity and blood compatibility of PSF membrane could be improved by chitosan and heparin conjugate. Copyright © 2003 John Wiley & Sons, Ltd.     

A silver optical sensor based on 5(p-dimethylaminobenzylidene)rhodanine immobilized on a triacetylcellulose membrane

An optical sensor has been proposed for the determination of silver by spectrophotometry. The sensor was prepared by immobilizing 5(p-dimethylaminobenzylidene)rhodanine on a transparent triacetylcellulose membrane. The effect of different variables on the response of the sensor was studied and the optimum conditions were established. The sensor responded linearly in the range 1.8–55.6 μM of silver with a limit of detection of 0.8 μM and a response time range of 8–10 min depending on the concentration of the silver ions. The presented optode is reversible and stable if stored in water for more than one month without reagent leaching. The relative standard deviation for seven replicated measurement of 4.6 and 37 μM silver was 3.15 and 2.76%, respectively. The sensor was successfully applied to the determination of silver in a silver sulphadiazine cream, an ore sample, and a radiology film. The text was submitted by the authors in English.     

Preparation of chitosan nanoparticles as carrier for immobilized enzyme

This work investigated the preparation of chitosan nanoparticles used as carriers for immobilized enzyme. The morphologic characterization of chitosan nanoparticles was evaluated by scanning electron microscope. The various preparation methods of chitosan nanoparticles were discussed and chosen. The effect of factors such as molecular weight of chitosan, chitosan concentration, TPP concentration, and solution pH on the size of chitosan nanoparticles was studied. Based on these results, response surface methodology was emploved. The results showed that solution pH, TPP concentration, and chitosan concentration significantly affected the size of chitosan nanoparticles. The adequacy of the predictive model equation for predicting the magnitude orders of the size of chitosan nanoparticles was verified effectively by the validation data. Immobilization conditions were investigated as well. The minimum particles size was about 42±5 nm under the optimized conditions. The optimal conditions of immobilization were as follow: one milligram of neutral proteinase was immobilized on chitosan nanoparticles for about 15 min at 40°C. Under the optimized conditions, the enzyme activity yield was 84.3%.     

Bioluminescent assays with immobilized firefly luciferase based on flow injection analysis

A flow-injection manifold incorporating immobilized firefly luciferase is described. The detector design and reaction conditions are discussed and results are presented for the determination of adenosine-5′-triphosphate over the range 1 × 10^?12?1 × 10^?5 M. Modifications for creatine phoshokinase (10–400 U l^?1) and creatine phosphate (10^?t–10^?1 M), both determined indirectly via ATP, are also described.     

Electrochemical immunosensor for carcinoembryonic antigen based on antigen immobilization in gold nanoparticles modified chitosan membrane.

A disposable electrochemical immunosensor for carcinoembryonic antigen (CEA) was proposed based on the antigen immobilized in a colloidal gold nanoparticles modified chitosan membrane on the surface of an indium-tin oxide (ITO) electrode. The different membranes were characterized by scanning electron microscope and electrochemical methods. Based on a competitive immunoassay format, the immobilized antigen of the immunosensor was incubated with a horseradish peroxidase (HRP) labeled antibody and sample CEA antigen, and the formed immunoconjugate in the immunosensor was detected by an o-phenylenediamine-H(2)O(2)-HRP electrochemical system. Under the optimal experimental conditions, the electrocatalytic current decreased linearly with the competitive mechanism. CEA could be determined in the linear range from 2.0 to 20 ng/ml with a detection limit of 1.0 ng/ml. The prepared CEA immunosensor is not only economic due to the low-cost ITO electrode obtained from industrial mass production, but is also capable with good stability and reproducibility for batch fabrication.     

A novel multicommuted fluorimetric optosensor for determination of resveratrol in beer

Resveratrol (3,5,4′-trihydroxystilbene) is a phytoalexin that plays a central role in the human diet because of its antioxidant, anticarcinogenic and antimutagenic properties. This paper shows the development of a multicommuted optosensing device for the determination of resveratrol in beer. The method is based on the measurement of the fluorescence (277/382 nm, λ_ex/λ_em) of the photoproduct on-line generated by UV-irradiation of resveratrol. The fluorescent photoproduct is monitored once it is retained on a solid support (Sephadex QAE A-25) in the detection area, which improves both sensitivity and selectivity. The sample was delipidated with toluene and cyclohexane and resveratrol was extracted by solid-phase extraction (SPE) on C₁₈ cartridges, using methanol as eluent. This pre-treatment allowed recovering about an 82% resveratrol and removing its 3-O-β-d-glycoside (piceid) and other interfering substances present in beer. The method provides a detection limit (DL) of 1.0 ng mL⁻¹ and a linear dynamic range (LDR) of 3.3-100 ng mL⁻¹. It was satisfactorily applied to the determination of resveratrol in top- and bottom-fermented beers by standard addition calibration. Resveratrol concentrations in the analysed samples varied from 4.1 to 14.1 ng mL⁻¹. This is the first proposed spectroscopic method for determination of resveratrol in beer.     

A novel flow-through fluorescence optosensor for the determination of thiabendazole

This paper presents the development of a new flow-injection system combined with solid-surface fluorescence detection for the determination of the widely used fungicide thiabendazole. Nylon powder was probed as a novel solid support for building the optosensor. The method is based on the on-line immobilization of thiabendazole onto nylon in a continuous flow system, followed by the measurement of its native fluorescence. Aqueous samples are directly injected in a water carrier, resulting in a very simple and economical method. The analytical figures of merit obtained using 1500 μL of sample and 75% methanol (v/v) as eluting solution were: linear calibration range from 8 to 120 ng mL⁻¹ (the lowest value corresponds to the quantitation limit), relative standard deviation, 0.9% (n = 5) at a level of 64 ng mL⁻¹, limit of detection calculated according to 1995 IUPAC recommendations is to 2.8 ng mL⁻¹, and sampling rate of 14 samples h⁻¹. The potential interference from other agrochemicals, metal ions and common anions, and the viability of determining thiabendazole in real water samples were also evaluated.     

Ammonium ion sensor based on immobilized nitrifying bacteria and a cation-exchange membrane

The ammonium ion sensor is based on nitrifying bacteria isolated from activated sludge. The sensor comprises a cation-exchange membrane, an alkaline solution layer (pH 10), a gas-permeable membrane, an immobilized microbial membrane, and an oxygen electrode. This novel combination provides accurate amperometric determinations of ammonium ions in aqueous solutions within 7 min in the range 10^-4– 4.5 × 10^-2 M. Volatile amines or other ions do not interfere. The relative error is within 4% and the sensor can be used continually for more than 10 days.     

Frequency response of the glucose sensor based on immobilized glucose oxidase membrane

Frequency response of the glucose sensor based on the immobilized glucose oxidase membrane was investigated experimentally by giving the sinusoidal change of glucose concentration to the glucose sensor and observing its output signal. Observed values of gains and phase lags of the frequency response of the glucose sensor followed the frequency response model of the first-order with dead time; The time constant and also the dead time were estimated and found to decrease as the amount of enzyme immobilized in the membrane increased and the thickness of the membrane decreased.

     

Sulphoxine immobilized onto chitosan microspheres by spray drying: application for metal ions preconcentration by flow injection analysis

A new chelating resin based on chitosan biopolymer modified with 5-sulphonic acid 8-hydroxyquinoline using the spray drying technique for immobilization is proposed. The chelating resin was characterized by thermogravimetric analysis (TGA) and X-ray diffraction (XRD) and surface area by nitrogen sorption. The efficiency of the chelating resin was evaluated by the preconcentration of metal ions Cu(II) and Cd(II) present in aqueous samples in trace amounts. The metal ions were previously enriched in a minicolumn and the concentrations of the analytes were determined on-line by flame atomic absorption spectrometry (FAAS). The maximum retention for Cu(II) occurred in the pH range 8-10, and for Cd(II) at pH 7. The optimum flow rate for sorption was found to be 7.2 ml min⁻¹ for the preconcentration of the metal ions. The analytes gave relative standard deviations (R.S.D.) of 0.7 and 0.6% for solutions containing 20 μg l⁻¹ of Cu(II) and 15 μg l⁻¹ of Cd (II), respectively (n=7). The enrichment factors for Cu(II) and Cd (II) were 19.1 and 13.9, respectively, and the limits of detection (LOD) were 0.2 μg l⁻¹ for Cd(II) and 0.3 μg l⁻¹ for Cu(II), using a preconcentration time of 90 s (n=11). The accuracy of the proposed method was evaluated by the metal ion recovery technique, in the analysis of potable water and water from a lake, with recoveries being between 97.2 and 107.3%.     

A lead (II) selective PVC membrane potentiometric sensor based on a tetraazamacrocyclic ligand

A polymeric membrane based Pb(II) selective potentiometric sensor was developed by using 1,3,7,9-tetraaza-2,8-dithia-4,10-dimethyl-6,12-diphenylcyclododeca-4,6,10,12-tetraene (TDDDCT) as an electroactive material along with anion excluder sodium tetraphenylborate (NaTPB) and plasticizer dioctylphthalate (DOP). The best performance in terms of slope, concentration range and response time was exhibited by the membrane having TDDDCT:PVC:DOP:NaTPB in the ratio 3:32:62:3 (w/w%). Potentiometric results show that the developed sensor works well in the concentration range 5.0 × 10^?7–1.0 × 10^?1 M with a near Nernstian slope of 29.5 (±0.5) mV decade^?1. The detection limit is down to 2.5 × 10^?7 M. The working pH range of this sensor is 2.8–7.0 and it works well in partially nonaqueous medium up to 25 % (v/v) methanol and ethanol. It exhibits a fast response time of 10 s. Selectivity coefficient values of various interfering ions were determined by the fixed interference method (FIM). The sensor reveals good selectivity for Pb(II) ions over other metal ions investigated. The developed sensor is used in the determination of lead in ‘Eveready battery waste’ and as an indicator electrode in the potentiometric titration of Pb(II) against EDTA.     

A novel flow-through fluorescence optosensor for the sensitive determination of tetracycline

A flow-through fluorescence optosensor with Sephadex G-50 microbeads as solid support is developed for the sensitive determination of tetracycline (TC). The fluorescent TC derivative encapsulated in CTAB micelle structures is retained onto the surface of the microbeads packed into a fluorescent flow cell in a flow system, followed by measurement of the native fluorescence of the TC derivative on the bead surface. The retained TC derivative is easily stripped off with DI water from the bead surface by breaking-down the micelle structure. This offers a convenient and effective way for the regeneration of the used solid support with DI water as a carrier. Under the optimal conditions, a linear calibration graph is obtained within a range of 3-500 μg L⁻¹, along with a detection limit of 1.0 μg L⁻¹. The present solid surface fluorescence optosensor provides a 22-fold improvement on the detection sensitivity for TC in comparison with that derived by fluorescence detection in aqueous medium. The feasibility of this flow-through fluorescence optosensor is evaluated by analyzing TC in a commercial drug tablet and surface water samples.     

A novel composite chitosan membrane for the separation of alcohol-water mixtures

A novel alcohol dehydration membrane with a three layer structure has been prepared. The top layer is a thin dense film of chitosan (CS), and the support layer is made of microporous polyacrylonitrile (PAN). Between the dense and microporous layer, there is an intermolecular cross-linking layer. This novel composite membrane has a high separation factor of more than 8000 and a good permeation rate of 0.26 kg/m² h for the pervaporation of 90 wt% ethanol aqueous solution at 60°C, 0.8 kg/m² h flux for a n-PrOH/water system and around 1 kg/m² h flux for an i-PrOH/water system using 80 wt% alcohol concentration at 60°C. The separation factor for both cases is more than 10⁵. The separation performance varies with feed composition, operating temperature and conditions of membrane preparation. The results show that the separation factor and flux of this membrane increase with raising the operating temperature. At the same time, the crosslinking layer improves durability of the composite membrane, and the pervaporation performance can be adjusted by changing the structure of the cross-linking layer. The cross section of the composite membrane has been examined by SEM.     

Fluorescence detection of trace PCB101 based on PITC immobilized on porous AAO membrane

A sensitive and selective fluorescent membrane for rapid detection of trace 2,2',4,5,5'-pentachlorinated biphenyl (PCB101) has been achieved by immobilizing the fluorophore phenyl isothiocyanate (PITC) onto porous anodic aluminium oxide (AAO) membrane (denoted as PITC@AAO). The fluorescence of the PITC@AAO membrane is obviously enhanced after titrating the analyte PCB101 into the membrane, being ascribed to the halogen-bonding interaction between the fluorophore PITC and the analyte PCB101. The fluorescence intensity increases with the PCB101 concentration in the low range below 1 ppm, and there exists an approximate linear relationship between the relative fluorescence intensity and the PCB101 concentration in the low range of 1-6 ppb. Moreover, the PITC@AAO membrane shows good selectivity; for example, it is insensitive to common structural analogs (polychlorinated aromatics). The mechanisms of the fluorescence enhancement and the better sensitivity and selectivity of the PITC@AAO membrane to PCB101 than that of PITC/n-hexane solution are also discussed. This work demonstrates that trace (in ppb range) PCBs can be detected by simple fluorescence measurement.