Determination of arsenite,arsenate, monomethylarsonic acid and dimethylarsinic acid in cereals by hydride generation atomic fluorescence spectrometry

A fast, sensitive and simple non-chromatographic analytical method was developed for the speciation analysis of toxic arsenic species in cereal samples, namely rice and wheat semolina. An ultrasound-assisted extraction of the toxic arsenic species was performed with 1 mol L^− 1 H₃PO₄ and 0.1% (m/v) Triton XT-114. After extraction, As(III), As(V), dimethylarsinic acid (DMA) and monomethylarsonic acid (MMA) concentrations were determined by hydride generation atomic fluorescence spectrometry using a series of proportional equations corresponding to four different experimental reduction conditions. The detection limits of the method were 1.3, 0.9, 1.5 and 0.6 ng g^− 1 for As(III), As(V), DMA and MMA, respectively, expressed in terms of sample dry weight. Recoveries were always greater than 90%, and no species interconversion occurred. The speciation analysis of a rice flour reference material certified for total arsenic led to coherent results, which were also in agreement with other speciation studies made on the same certified reference material.     

Ultrasound-assisted extraction in the determination of arsenic,cadmium, copper,lead, and silver in contaminated soil samples by inductively coupled plasma atomic emission spectrometry

An extraction method was developed for the determination of toxic elements in contaminated soil samples by inductively coupled plasma atomic emission spectrometry (ICP-AES). The determination of arsenic, cadmium, lead, and silver in ultrasound-assisted extracts of SRM 2710 and SRM 2711 by ICP-AES was carried out with high accuracy and precision (RSD<3.7%). The certified concentrations of the SRMs were obtained for arsenic, cadmium, lead, and silver by using an ultrasound-assisted extraction method with a digestion solution of (1+1)-diluted aqua regia. The determination of copper in SRMs by the ultrasound-assisted extraction method and analysis by ICP-AES failed to obtain the certified concentrations at the 95% level of confidence using (+/-2 s) as confidence limits of the mean. However, the same results were observed with the use of the microwave digestion method and reflux, which is the ISO 11466 standard method. The analysis of the SRMs showed that the ultrasound-assisted extraction method is highly comparable with the other methods used for such purposes. The major advantages of the ultrasound-assisted extraction method compared to the microwave and reflux methods are the high treatment rate (50 samples simultaneously in nine minutes) and low reagent usage, the main benefit of which are the low chloride and nitrate concentrations in the extracts.     

一次消解土壤样品测定汞、砷和硒

建立了测定土壤中3种挥发性元素(汞、砷、硒)的一次消解方法,确定以程序控温石墨自动消解仪+王水-氢氟酸-硼酸络合敞开体系为最佳消解体系,采用氢化物发生-原子荧光光谱法(HG-AFS)分别测定同一消解液中汞、砷、硒的含量.采用国家标物中心有证标准物质土壤环境样品GSS-1~GSS-8进行了方法验证,结果均符合标准偏差的允许范围.此消解方法相比于现行标准方法,避免了针对各元素的分次处理,简化了消解步骤,节省了前处理时间,减少了试剂消耗,提高了实验效率,适用性广、灵敏度高、检出限低,尤其适合批量样品的微量/痕量元素分析,可作为一种大规模土壤样品中重金属污染监测和治理的快捷方法.     

Determination of thallium in sediments of the River Elbe using isotope dilution mass spectrometry with thermal ionization.

By using isotope dilution mass spectrometry with thermal ionization, TI concentrations were determined in sediments from six sampling positions of the River Elbe in the area of the former GDR (Bad Schandau, Dresden, Barby, Magdeburg, Werben/Havel and Cumlosen). For comparison, two samples from the River Rhine near Emmerich taken in 1978 and 1990 and the Community Bureau of Reference (BCR) certified reference material (CRM) 320 River Sediment were also analysed. Thallium concentrations after complete decomposition by high-pressure digestion (HNO3 + HF) and aqua regia [HCI-HNO3 (3 + 1)] ranged from 537 micrograms kg-1 in the BCR CRM 320 to 5192 micrograms kg-1 in the River Rhine sediment (1978) near Emmerich. The reproducibility of the method ranged from 0.06 to 4.7%. Only 49-94% of the total amount of TI was found after extraction with 1 mol dm-3 HNO3 and 43-86% after extraction with aqua regia. Sediments from Dresden, Barby, Werben/Havel and Cumlosen were found to have virtually identical TI concentrations as the River Rhine sediment sampled in 1990. In comparison with the extremely high Hg and As concentrations found in the River Elbe in an earlier study, the TI concentrations were not as high as expected.     

双道氢化物发生-原子荧光光谱法同时测定核电用钢中痕量砷和锑

建立了双道氢化物发生-原子荧光光谱法同时测定核电用钢中痕量砷和锑的新方法。用王水溶解样品,以2.0 g/L L-半胱氨酸溶液作为预还原剂,在低酸度条件下实现对砷、锑的预还原。用20 g/L硼氢化钾溶液作为还原剂,氢化物发生反应在0.5 mol/L乙酸介质中进行。砷、锑的质量浓度在40μg/L范围与相应的荧光强度呈线性关系,方法的检出限(3s/k)分别为0.032μg/L和0.022μg/L。应用此方法同时测定了核电用钢及不锈钢标准样品中的砷锑含量,并与电感耦合等离子体原子发射光谱法的分析结果作了对比,测定值与标准样品的标准值相符,结果的相对标准偏差(n=8)均小于5.0%。     

A set of four soil reference materials with certified values of total element contents and their extractable fractions

A set of certified reference materials of four natural soils denoted as CRM 7001-4 was prepared. They consist of light sandy soils with normal and elevated, silty clay loam with normal, and loam with elevated element levels. Certified and/or information values were established for the total contents of the elements As, Ba, Be, Cd, Co, Cr, Cu, Hg, Mn, Ni, Pb, V, Zn, and their fractions, extractable with aqua regia, and boiling and cold 2 mol L^–1 nitric acid, from results of a 28 laboratory intercomparison using various methods of atomic absorption spectrometry, optical emission spectrometry, mass spectrometry, electrochemical methods, spectrophotometry, instrumental neutron activation analysis, and X-ray fluorescence.     

Arsenic speciation based on ion exchange high-performance liquid chromatography hyphenated with hydride generation atomic fluorescence and on-line UV photo oxidation

An on-line method capable of the separation of arsenic species was developed for the speciation of arsenite As(III), arsenate As(V), monomethylarsenic (MMA) and dimethylarsenic acid (DMA) in biological samples. The method is based on the combination of high-performance liquid chromatograph (HPLC) for separation, UV photo oxidation for sample digestion and hydride generation atomic fluorescence spectrometry (HGAFS) for sensitive detection. The best separation results were obtained with an anion-exchange AS11 column protected by an AG11 guard column, and gradient elution with NaH₂PO₄ and water as mobile phase. The on-line UV photo oxidation with 1.5% K₂S₂O₈ in 0.2 mol L^–1 NaOH in an 8 m PTFE coil for 40 s ensures the digestion of organoarsenic compounds. Detection limits for the four species were in the range of 0.11–0.15 ng (20 μL injected). Procedures were validated by analysis of the certified reference materials GBW09103 freeze-dried human urine and the results were in good agreement with the certified values of total arsenic concentration. The method has been successfully applied to speciation studies of blood arsenic species with no need of sample pretreatment. Speciation of arsenic in blood samples collected from two patients after the ingestion of realgar-containing drug reveals slight increase of arsenite and DMA, resulting from the digestion of realgar.     

Determination of molybdenum in steels by flow-injection spectrophometry

A flow-injection procedure is proposed for the determination of molybdenum in steels based on the thiocyanate method. Effects of iron(III), acidity, reagent concentration and interfering species were investigated by using flow-injection systems with the merging zones approach which reduced drastically the number of standard solutions to be prepared. Full details of system design are given. The procedure can be applied to several types of steel samples of industrial relevance. After dissolution of the steels in aqua regia, molybdenum can be determined in the range 0.10–4.00% (w/w) at a rate of up to 270 samples per hour with relative standard deviations less than 2%. The results agree with those obtained by atomic absorption spectrometry with the standard addition method and by plasma atomic emission spectrometry, and with certified values of standard reference samples.     

微波辅助提取-液相色谱-氢化物发生-原子荧光光谱法分析沉积物中砷的形态

采用微波辅助提取-液相色谱-氢化物发生-原子荧光光谱法(LC-HG-AFS)联用技术分析了太湖沉积物中砷的形态[亚砷酸(As(III))、二甲基砷酸钠(DMA)、一甲基砷酸二钠(MMA)和砷酸As(V)]。测得沉积物中以无机砷为主,且以As(V)居多。选定以1mol/L的磷酸和0.1mol/L抗坏血酸为提取液,在微波辅助萃取(功率为60W,时间12min)下,萃取率达79.84%～91.57%,回收率在94.78%～107.6%之间。4种砷的形态在0～160μg/L之间时线性良好,检测限为0.6～2.3μg/L,相对标准偏差RSD为1.62%～2.20%。方法具有简便、快速、灵敏的特点。     

微波王水消解不赶酸原子荧光光谱法测定土壤中的砷

采用微波消解土壤样品不赶酸的情况下利用原子荧光光谱法测定土壤中的砷.结果表明:微波王水消解土壤样品不赶酸情况下,砷的测定值均在国家标准物质ESS-1的推荐值范围内.砷的线性范围分别为0.0～50.0μg/L,相关系数为r=0.9995.按称取0.2 g样品,定容至50 mL,求出砷检出限为0.5 mg/kg.砷回收率为93.4%～100.9%之间,相对标准偏差(n=4)为0.39～4.56%.结果表明:微波王水消解不赶酸原子荧光光谱法测定土壤中的砷,灵敏度高,操作简便快速,结果准确可靠.     

Arsenic speciation based on ion exchange high-performance liquid chromatography hyphenated with hydride generation atomic fluorescence and on-line UV photo oxidation

An on-line method capable of the separation of arsenic species was developed for the speciation of arsenite As(III), arsenate As(V), monomethylarsenic (MMA) and dimethylarsenic acid (DMA) in biological samples. The method is based on the combination of high-performance liquid chromatograph (HPLC) for separation, UV photo oxidation for sample digestion and hydride generation atomic fluorescence spectrometry (HGAFS) for sensitive detection. The best separation results were obtained with an anion-exchange AS11 column protected by an AG11 guard column, and gradient elution with NaH2PO4 and water as mobile phase. The on-line UV photo oxidation with 1.5% K2S2O8 in 0.2 mol L(-1) NaOH in an 8 m PTFE coil for 40 s ensures the digestion of organoarsenic compounds. Detection limits for the four species were in the range of 0.11-0.15 ng (20 microL injected). Procedures were validated by analysis of the certified reference materials GBW09103 freeze-dried human urine and the results were in good agreement with the certified values of total arsenic concentration. The method has been successfully applied to speciation studies of blood arsenic species with no need of sample pretreatment. Speciation of arsenic in blood samples collected from two patients after the ingestion of realgar-containing drug reveals slight increase of arsenite and DMA, resulting from the digestion of realgar.     

New Approaches to the Extraction of Arsenic Species from Soils

Arsenic extraction in natural and spiked soil samples was studied using two main types of extractants. The extractants were phosphoric acid used alone and with the addition of reducing agents (ascorbic acid and hydroxylammonium hydrochloride). The stability of arsenite (As(III)), arsenate (As(V)), monomethylarsonic acid (MMA) and dimethylarsinic acid (DMA) in the extracts over time and under different storing conditions was assessed by means of LC-HG-AFS. A protocol was devised to extract arsenic species from soils. The protocol assures the stability of the original sample species in the extract proposed by using an extraction solution of phosphoric acid with ascorbic acid and by purging the extracts after microwave extraction. The total As, Mn and Fe content in aqua regia and in phosphoric extracts was also measured by ICP-AES in order to perform the mass balance.     

原子荧光法测定土壤中砷的消解方法研究

分别用王水消解法和硫酸-硝酸-高氯酸混合酸消解法处理样品,用原子荧光光度计法测定了砷的含量,比较了两种消解方法砷的测定值和标准值.结果表明,采用混合酸消解法砷的测定值低于标准值,而采用王水消解法可以准确测定土壤中砷含量,实验操作简单方便,结果准确、可靠.     

Extraction and speciation of arsenic in plants grown on arsenic contaminated soils

A sequential arsenic extraction method was developed that yielded extraction efficiencies (EE) that were approximately double those using current methods for terrestrial plants. The method was applied to plants from two arsenic contaminated sites and showed potential for risk assessment studies. In the method, plants were extracted first by 1:1 water-methanol followed by 0.1 M hydrochloric (HCl) acid. Total arsenic in plant and soil samples collected from contaminated sites was mineralized by acid digestion and detected by inductively coupled plasma-atomic emission spectrometry (ICP-AES) and hydride generation-atomic absorption spectrometry (HG-AAS). Arsenic speciation was done by high performance liquid chromatography coupled with HG-AAS (HPLC-HGAAS) and by HPLC coupled with ICP-mass spectrometry (HPLC-ICP-MS). Spike recovery experiments with arsenite (As(III)), arsenate (As(V)), methylarsonic acid (MA) and dimethylarsinic acid (DMA) showed stability of the species in the extraction processes. Speciation analysis by X-ray absorption near edge spectroscopy (XANES) demonstrated that no transformation of As(III) and As(V) occurred due to sample handling. Dilute HCl was efficient in extracting arsenic from plants; however, extraction and determination of organic species were difficult in this medium. Sequential extraction with 1:1 water-methanol followed by 0.1 M-HCl was most useful in extracting and speciating both organic and inorganic arsenic from plants. Trace amounts of MA and DMA in plants could be detected by HPLC-HGAAS aided by the process of separation and preconcentration of the sequential extraction method. Both organic and inorganic arsenic compounds could be detected simultaneously in synthetic gastric fluid extracts (GFE) but EEs by this method were lower than those of the sequential method. The developed sequential method was shown to be reliable and applicable to various terrestrial plants for arsenic extraction and speciation.     

Ion chromatography–inductively coupled plasma mass spectrometry determination of arsenic species in marine samples

Arsenic speciation analysis in marine samples was performed using ion chromatography (IC) with inductively coupled plasma mass spectrometry (ICP‐MS) detection. The separation of eight arsenic species, viz. arsenite, monomethyl arsonic acid, dimethylarsinic acid, arsenate, arsenobetaine, tetramethylarsine oxide, arsenocholine and tetramethylarsonium ion was achieved on a Dionex AS4A (weaker anion exchange column) by using a nitric acid pH gradient eluent (pH 3.3 to 1.3). The entire separation was accomplished in 12 min. The detection limits for the eight arsenic species by IC–ICP‐MS were in the range 0.03–1.6 µ g l^?1, based on 3σ of the blank response (n = 6). The repeatability and day‐to‐day reproducibility were calculated to be less than 10% (residual standard deviation) for all eight species. The method was validated by analyzing a certified reference material (DORM‐2, dogfish muscle) and then successfully applied to several marine samples, e.g. oyster, fish muscle, shrimp and marine algae. The low power microwave digestion was employed for the extraction of arsenic from seafood products. Copyright © 2004 John Wiley & Sons, Ltd.     

Sequential extraction for the speciation of some heavy metals in soils

The five step sequential extraction for speciation of copper and nickel originally designed for sediments has been applied to soil samples. The extractant solutions were: 1 mol/l ammonium acetate, 1 mol/l hydroxylammonium chloride in 25% acetic acid (1∶1), 0.1 mol/l hydrochlorid acid, 0.5 mol/l sodium hydroxide and 8 mol/l nitric acid. The residue was decomposed by HF and HNO₃. Using this procedure the metal fraction bound to the organic matter can be distinguished. The concentrations of analytes were determined in the soil extracts by FAAS and ETAAS. Accuracy was assessed by comparing the sum of the contents of copper and nickel in soil extracts with the total certified values of CRMs of soils. The overall recovery values for nickel was 84–105% and for copper 105–114%.     

Separation and Detection of Arsenic and Selenium Species in Environmental Samples by HPLC-ICP-MS

A method is presented for arsenic speciation analysis of an oyster sample using ion chromatography coupled with an inductively coupled plasma mass spectrometry (ICP-MS) instrument. A strong anion exchange resin was employed with a step gradient elution of 0.1 mM/0.1 M K 2 SO 4 at pH 10.2. Arsenobetaine and dimethylarsinic acid were determined following extraction based on trypsin enzymolysis with 95-100% extraction efficiency. Limits of detection in the range 0.1-0.3 mg kg m 1 of arsenic were obtained for organic arsenic species. No inorganic arsenic was detected. Validation was performed using TORT-2 as a certified reference material. Although high performance liquid chromatography (HPLC) coupled to ICP-MS is an effective method for speciation analysis it is not always necessary to obtain such a detailed picture. A simple liquid chromatographic separation technique based upon mini-column technology is presented. It was developed to obtain a fast, efficient and reliable separation of inorganic from organic, i.e. assumed toxic from non-toxic, arsenic and selenium species suitable for use as an initial screening method for environmental analysis. Two types of strong anion exchange resin were tested. Excellent separation was obtained for both min-column resins and analysis times were within 7 min. Limits of detection obtained for inorganic arsenic, organic arsenic, selenomethionine, Se IV and Se VI were 1.6, 1.8, 66, 32 and 22 µg kg m 1 , respectively.     

Determination of arsenic species in marine samples by HPLC-ICP-MS.

Arsenic speciation analysis in marine samples was performed using high performance liquid chromatography (HPLC) with ICP-MS detection. The separation of eight arsenic species viz. arsenite (As(III)), monomethylarsonic acid (MMA), dimethylarsinic acid (DMA), arsenate (As(V)), arsenobetaine, trimethylarsine oxide (TMAO), arsenocholine and tetramethylarsonium ion (TeMAs) was achieved on a Shiseido Capcell Pak C18 column by using an isocratic eluent (pH 3.0), in which condition As(III) and MMA were co-eluted. The entire separation was accomplished in 15 min. The detection limits for 8 arsenic species by HPLC/ICP-MS were in the range of 0.02 - 0.10 microg L(-1) based on 3sigma of blank response (n=9). The precision was calculated to be 3.1-7.3% (RSD) for all eight species. The method then successfully applied to several marine samples e.g., oyster, scallop, fish, and shrimps. For the extraction of arsenic species from seafood products, the low power microwave digestion was employed. The extraction efficiency was in the range of 52.9 - 112.3%. Total arsenic concentrations were analyzed by using the microwave acid digestion. The total arsenics in the certified reference materials (DORM-2 and TORT-2) were analyzed and agreed with the certified values. The concentrations of arsenics in marine samples were in the range 6.6 - 35.1 microg g(-1).     

Validation of a method for arsenic speciation in food by ion chromatography-inductively coupled plasma/mass spectrometry after ultrasonic-assisted enzymatic extraction

A fully validated and rapid quantitative method is presented for determination of inorganic arsenic [arsenite, As(III) and arsenate, As(V)] and organic arsenic species (methylarsonic acid, dimethylarsinic acid, and arsenobetaine) by ion chromatography paired with inductively coupled plasma/MS after ultrasonic-assisted enzymatic extraction (UAEE) in rice- and seafood-based raw materials and finished products. This method gives toxicological meaning to arsenic analysis, since the sum of the toxic chemical forms As(III) and As(V) can be determined. In contrast to classical water-methanol extraction, UAEE enables drastic acceleration of sample extraction (5 min instead of several hours), while total arsenic extraction efficiency is improved without species conversion. Validation was performed to evaluate the method for selectivity, linearity, LOD/LOQ (0.007-0.020 mg/kg), trueness, precision (HorRat values, 0.2-0.6), recovery (93-122%), and uncertainty. The method was also satisfactorily tested using two proficiency tests. Performance characteristics are reported for four certified reference materials, standard reference material (SRM) 1568a (rice flour), Institute for Reference Materials and Measurements 804 (rice flour), SRM 2976 (mussel tissue), certified reference material-627 (tuna fish), and several commercial food samples populating five AOAC triangle food sectors. The results indicated that this speciation method is cost-efficient, time-saving, and accurate, as well as fit-for-purpose, according to International Organization for Standardization/International Electrotechnical Commission 17025:2005 standard, and could be used for routine analysis.     

Optimization of the extraction for the determination of arsenic species in plant materials by high-performance liquid chromatography coupled with hydride generation atomic fluorescence spectrometry

A study has been conducted for the separation and the determination of arsenic species in plants using high-performance liquid chromatography–hydride generation atomic fluorescence spectrometry with emphasis on sample extraction procedures. Various extraction solvents have been applied to extract arsenic species from plants in order to investigate the uptake, transfer and accumulation processes of arsenic. The method was optimized with respect to the selection of extraction solvent, extraction time and the number of extraction steps. The analytical procedure has been validated by analyzing standard reference material GBW 82301 (peach leaves) and successfully used for the arsenic speciation in plants grown on contaminated soil near an arsenic mine. Inorganic arsenic, especially arsenate (As(V)) appears to be the major component in plants and organic arsenic species of monomethylarsenic acid and dimethylarsenic acid were detected at low concentrations.