Simultaneous determination of norfloxacin and lomefloxacin in milk by first derivative synchronous fluorescence spectrometry using Al (III) as an enhancer

A novel method for the simultaneous determination of norfloxacin (NFLX) and lomefloxacin (LFLX) in milk samples was developed by using first derivative synchronous fluorimetry. The synchronous fluorescence (Δλ=160 nm) spectra and first derivative synchronous fluorescence spectra of NFLX, LFLX and their mixture were studied. The zero-crossing method was utilized to measure the first derivative value of the derivative spectrum. The zero-crossing points were located at 275.0 nm for NFLX and at 283.8 nm for LFLX, in first derivative synchronous fluorescence spectra. Therefore, 283.8 nm and 275.0 nm were selected for the determination of NFLX and LFLX. The first derivative values varied linearly with the concentrations in the range of 1.68×10(-8)-5.64×10(-6) mol L(-1) for NFLX and 1.89×10(-8)-6.19×10(-6) mol L(-1) for LFLX. The detection limits were 5.03×10(-9) mol L(-1) for NFLX and 7.58×10(-9) mol L(-1) for LFLX. The proposed method is reliable, selective and sensitive, and has been used successfully in the simultaneous determination of NFLX and LFLX in milk samples, whose results were in good agreement with those obtained by HPLC.     

二阶导数同步荧光光谱法同时直接测定厚朴酚及和厚朴酚

研究了厚朴酚与和厚朴酚及其混合溶液的二阶导数同步荧光光谱,结果两者的二阶导数同步荧光光谱得到完全分离,消除了彼此间的干扰,据此建立了一种二阶导数同步荧光光谱法同时直接测定混合物中厚朴酚与和厚朴酚的新方法.厚朴酚与和厚朴酚的线性范围分别为2.8～500.0 μg/L和4.3～560.0 μg/L;检出限分别为0.84和1.30 μg/L,回收率分别为94.65%～105.58%和95.09%～104.51%; 相对标准偏差均低于4.08%.本方法用于同时直接测定厚朴药材及其提取物中厚朴酚与和厚朴酚含量,结果令人满意.     

Multicomponent determination of the pesticide naptalam and its metabolites in river water, by applying partial least squares calibration to the derivative spectrophotometric signals

A multivariate calibration method, partial least squares (types PLS-1 and PLS-2), was applied to the simultaneous determination of naptalam (N-(1-naphthyl) phthalamic acid) and its metabolites N-(1-naphthyl) phthalimide and 1-naphthylamine in mixtures by UV-visible absorption spectrophotometry. The absorption and first-derivative absorption spectra of mixtures were used to perform the optimization of the calibration matrices by the PLS method. Two different experimental designs for the three-component mixtures are assayed and the results are discussed. The proposed method with the derivative spectra was applied to the determination of these analytes in river water at the ppb level.     

A new fractional wavelet approach for the simultaneous determination of ampicillin sodium and sulbactam sodium in a binary mixture

A new application of the fractional wavelet transform (FWT) was proposed for the simultaneous determination of ampicillin (AP) and sulbactam (SB) in a pharmaceutical combination for injection. FWT approach is a new powerful tool for removing noise and irrelevant information from the absorption spectra. Cardinal information having higher peak amplitude, eliminated noise, sharp peaks with shrinking width of spectral range was obtained by the application of FWT procedure to the original absorption spectra. In this paper, FWT approach was subjected to the data vector of the UV-signals obtained from AP and SB in the wavelength range of 211.5-313.8 nm. Derivative transform was applied to the original absorption signal together with its FWT generalization. The calibration graphs for AP and SB were obtained by measuring the FWT and usual derivative amplitudes at zero-crossing points. The method validation was carried out by using the synthetic mixture analysis. Our proposed FWT approach was compared with the usual derivative spectrophotometry and chemometric methods (CLS, PCR and PLS) and a good agreement was reported.     

紫外光谱法对维生素E油酸酯、维生素E与油酸的同时测定

建立了混合体系中维生素E、油酸和维生素E油酸酯同时测定的方法,用光纤光谱仪获取混合体系紫外-可见透射光谱.实验按均匀设计建立校正集和预测集,在255 ～315 nm波段采用偏最小二乘法建立了同时定量测定该3组分的校正模型,并用间隔区间偏最小二乘法(iPLS)通过优选建模区间改进油酸的预测模型.采用iPLS能够显著提高模型准确度,尤其对光谱弱响应的物质,最大相对误差从PLS直接建模的54.7%降至iPLS的8.98%,建立的模型可满足动力学研究的原位分析需要.     

Simultaneous spectrophotometric determination of phenanthridine, phenanthridinone and phenanthridine N-oxide using multivariate calibration methods

The multivariate calibration methods, partial least squares (PLS) and principle component regression (PCR) have been used to determine phenanthridine, phenanthridinone and phenanthridine N-oxide in spiked human plasma samples. Resolution of binary and ternary mixtures of analytes with minimum sample pre-treatment and without analyte separation has been successfully achieved analyzing the UV spectral data. The net analyte signal (NAS) concept was also used to calculate multivariate analytical figures of merit such as limit of detection, selectivity and sensitivity. The simultaneous determination of three analytes was possible by PLS and PCR processing of sample absorbance in the 210–355 nm region. Good recoveries were obtained for both synthetic mixtures and spiked human plasma samples.     

Simultaneous kinetic-spectrophotometric determination of levodopa and benserazide by bi- and three-way partial least squares calibration

A procedure for the simultaneous kinetic-spectrophotometric determination of levodopa (I) and benserazide (II), from their oxidation reaction with KIO(4) in an acidic medium, is described. Both species instantly oxidize, giving rise to compounds which present maximum values of absorbance close to 400 nm. In the presence of an excess of the oxidizing agent, the levodopa derivative evolves to form the corresponding aminochrome (lambda(m)=480 nm), while the benserazide derivative decomposes to yield colorless compounds. The appearance of new compounds, with absorption bands in the region of 500-700 nm, is additionally seen upon adding the oxidizing agent to a mixture of I and II. These compounds also evolve decomposing and forming colorless products. In spite of the complexity of the system studied, the calibration by bi-linear partial least squares (PLS) as well as by three-way partial least squares (nPLS) permit the quantification of both analytes with a precision on the order of 0.7% for levodopa and of 1.5% for benserazide. nPLS also allows for the qualitative interpretation of the phenomena which occur. The proposed method is applied to the quantification of I and II in the commercial, pharmaceutical preparation Madopar, using high performance liquid chromatography (HPLC) as the analytical reference technique.     

Resolution of mixtures of three nonsteroidal anti-inflammatory drugs by fluorescence using partial least squares multivariate calibration with previous wavelength selection by Kohonen artificial neural networks

A spectrofluorometric method for the quantitative determination of flufenamic, mefenamic and meclofenamic acids in mixtures has been developed by recording emission fluorescence spectra between 370 and 550 nm with an excitation wavelength of 352 nm. The excitation–emission spectra of these compounds are deeply overlapped which does not allow their direct determination without previous separation. The proposed method applies partial least squares (PLS) multivariate calibration to the resolution of this mixture using a set of wavelengths previously selected by Kohonen artificial neural networks (K-ANN). The linear calibration graphs used to construct the calibration matrix were selected in the ranges from 0.25 to 1.00 μg ml⁻¹ for flufenamic and meclofenamic acids, and from 1.00 to 4.00 μg ml⁻¹ for mefenamic acid. A cross-validation procedure was used to select the number of factors. The selected calibration model has been applied to the determination of these compounds in synthetic mixtures and pharmaceutical formulations.     

Synchronous fluorimetric determination of salicylic acid and diflunisal in human serum using partial least-squares calibration

The simultaneous determination of salicylic acid and diflunisal in human serum has been accomplished by synchronous fluorimetry, in combination with partial least-squares multivariate calibration. The total luminescence information of the analytes has been used to optimize the spectral data set for the calibration, by analysis of the three-dimensional excitation-emission matrices. The synchronous spectrum, maintaining a constant difference of Deltalambda = 128 nm between the emission and excitation wavelengths, has been selected as optimum to perform the determination. The method is based on the fluorescence of these compounds in chloroform containing 1% (v/v) acetic acid. Serum samples are treated with trichloroacetic acid to remove the proteins, and both analytes are extracted into chloroform-1% (v/v) acetic acid prior to the determination. For concentrations ranging from 60-240 mug ml(-1) of each drug, analytical recoveries range from 96% to 103% for salicylic acid and from 97% to 105% for diflunisal.     

Rapid simultaneous analysis of 1-naphthol and 2-naphthol in water samples by derivative variable-offset synchronous fluorescence spectroscopy

Derivative variable-offset synchronous fluorescence spectroscopy is developed to improve the spectral resolution and the selectivity of fluorescence measurements. 1-naphthol and 2-naphthol are employed to evaluate the proposed coupled technique and the various spectral comparisons are conducted. Second derivative variable-offset synchronous scanning permits the rapid simultaneous identification and quantitative determination of 1-naphthol and 2-naphthol in a mixture from a single spectrum. 6.7-2000 ng/ml 1-naphthol and 3.6-500 ng/ml 2-naphthol can be quantified with 1-naphthol and 2-naphthol ratios of 40: 1-1: 10. The determination of 1-naphthol and 2-naphthol in various spiked water samples gave a mean recovery of 100.7% with a relative standard deviation of 2.8% for 1-naphthol and mean recovery of 99.7% with a relative standard deviation (RSD of 2.6% for 2-naphthol, respectively.     

Genetic‐Algorithm‐Based Wavelength Selection in Multicomponent Spectrophotometric Determination by PLS: Application on Ascorbic Acid and Uric Acid Mixture

Genetic algorithm (GA) is a suitable method for selecting wavelengths for partial least squares (PLS) calibration of mixtures with almost identical spectra without loss of prediction capacity using the spectrophotometric method. In this study, the concentration model is based on absorption spectra in the range of 200‐320 nm for 25 different mixtures of ascorbic acid (AA) and uric acid (UA). The calibration curve was linear over the concentration range of 1‐15 and 2‐16 μg mL^?1 for ascorbic acid and uric acid, respectively. The root mean square deviation (RMSD) for ascorbic acid and uric acid with GA and without GA were 0.3071 and 0.3006, 0.3971 and 0.7063, respectively. The proposed method was successfully applied to the simultaneous determination of both analytes in human serum and urine samples.     

Simultaneous determination of codeine and pyridoxine in pharmaceutical preparations by first-derivative spectrofluorimetry

A method for the simultaneous determination of codeine and pyridoxine was developed, based on the measurement of their native fluorescence signals, by using first-derivative spectrofluorimetry to resolve the mixture. Codeine was measured at lambda(em) = 309 nm, and pyridoxine was measured at lambda(em) = 450 nm. Instrumental parameters were optimized, and the emission spectra were recorded between 275 and 475 nm, at lambda(ex) = 255 nm and excitation and emission slit widths of 2.5 and 10 nm, respectively. Systematic studies on the influence of species usually present along with the analytes (such as caffeine, ascorbic acid, paracetamol, and thiamine) were also performed. The calibration graphs were linear over the ranges of 0.5-7.0 and 0.1-1.0 microg/mL for codeine and pyridoxine, respectively, and the relative standard deviations (n = 10) were about 3%. The method was successfully applied to the determination of codeine and pyridoxine in solutions of synthetic mixtures and in synthetic and semisynthetic pharmaceutical formulations.     

Simultaneous quantification of promazine hydrochloride and its sulfoxide in pharmaceutical preparations.

The use of derivative UV-spectrophotometry is proposed for the simultaneous quantification of promazine hydrochloride in the presence of sulfoxide, and vice versa. For this purpose, mathematical parameters were established for generating derivative spectra of analytes. The determination of promazine was made using the first-order derivative (deltalambda = 10 nm, second polynomial degree) at 268 nm. The quantification of sulfoxide was achieved by applying third-derivative spectra (deltalambda = 14 nm, sixth polynomial degree) based on measurements of the amplitude at 342 - 344 nm. An elaborated method was successfully used to determine analytes in commercial promazine pharmaceuticals. The obtained results agreed well with those obtained by the HPLC method.     

Simultaneous determination of two anti-inflammatory drugs in serum using isopotential fluorimetry

The simultaneous determination of 6-methoxy-2-naphthylacetic acid (6MNA) and diflunisal in serum samples using the combination of matrix isopotential synchronous fluorescence (MISF) and first derivative technique is proposed. 6MNA and diflunisal exhibit overlapped spectra and serum produces background fluorescence that precludes the direct determination of these anti-inflammatory drugs by conventional fluorimetry. This method provides good analytical results for determination of compounds in samples with unknown background fluorescence. The method was applied for the simultaneous determination of 6MNA and diflunisal in serum samples at concentrations between 20-200 and 100-1000 ng mL⁻¹, respectively, by means of absolute values of first derivative of synchronous scan at 247.9/364.0 and 262.6/392.4 nm for 6MNA and diflunisal, respectively. In order to obtain maximum sensitivity and adequate selectivity, factors affecting fluorescence intensity were studied. As a result, the analyses were performed in water at a pH of 7.2, adjusted by using sodium dihydrogen phosphate/hydrogen phosphate (0.1 M) as a buffer solution. Serum samples were diluted 200 times. Analytical parameters of the proposed method were calculated according to the error propagation theory. The limit of detection calculated according to Clayton was 15.8 and 63.0 ng mL⁻¹ for 6MNA and diflunisal, respectively. The sensitivity, repeatability and reproducibility achieved with the proposed method were adequate for the determination of these anti-inflammatory agents in serum samples.     

Simultaneous spectrophotometric determination of mercury and palladium with Thio-Michler's Ketone using partial least squares regression and orthogonal signal correction

A simple, novel and sensitive spectrophotometric method was described for simultaneous determination of mercury and palladium. The method is based on the complex formation of mercury and palladium with Thio-Michler's Ketone (TMK) at pH 3.5. All factors affecting on the sensitivity were optimized and the linear dynamic range for determination of mercury and palladium found. The simultaneous determination of mercury and palladium mixtures by using spectrophotometric method is a difficult problem, due to spectral interferences. By multivariate calibration methods such as partial least squares (PLS), it is possible to obtain a model adjusted to the concentration values of the mixtures used in the calibration range. Orthogonal signal correction (OSC) is a preprocessing technique used for removing the information unrelated to the target variables based on constrained principal component analysis. OSC is a suitable preprocessing method for PLS calibration of mixtures without loss of prediction capacity using spectrophotometric method. In this study, the calibration model is based on absorption spectra in the 360-660 nm range for 25 different mixtures of mercury and palladium. Calibration matrices were containing 0.025-1.60 and 0.05-0.50 microg mL(-1) of mercury and palladium, respectively. The RMSEP for mercury and palladium with OSC and without OSC were 0.013, 0.006 and 0.048, 0.030, respectively. This procedure allows the simultaneous determination of mercury and palladium in synthetic and real matrix samples good reliability of the determination.     

Partial least squares-near infrared determination of pesticides in commercial formulations

A solvent free, fast and environmentally friendly near infrared-based methodology (NIR) was developed for pesticide determination in commercially available formulations. This methodology was based on the direct measurement of the diffuse reflectance spectra of solid samples and a multivariate calibration model (partial least squares, PLS) to determine the active principle concentration in commercial formulations. The PLS calibration set was built on using the spiked samples by mixing different amounts of pesticide standards and powdered samples. Buprofezin, Diuron and Daminozide were used as test analytes. Concentration of Buprofezin in the samples was calculated employing a 4-factors PLS calibration using the spectral information in the range between 2231–2430 and 1657–1784 nm. For Diuron determination a 1-factor PLS calibration model using the spectral range 1110–2497 nm, after a linear removed correction. Daminozide determination was carried out employing a 4-factors PLS model using the spectral information in the ranges 1644–1772 and 2014–2607 nm without baseline correction. The root mean square errors of prediction (RMSEP) found were 1.1, 1.7 and 0.7% (w/w) for Buprofezin, Diuron and Daminozide determination, respectively. The developed PLS-NIR procedure allows the determination of 120 samples/h, does not require any sample pre-treatment and avoids waste generation.     

Determination of phenylephrine hydrochloride and chlorpheniramine maleate in binary mixture using chemometric-assisted spectrophotometric and high-performance liquid chromatographic-UV methods

Four methods have been developed for the simultaneous determination of phenylephrine hydrochloride and chlorpheniramine maleate without previous separation. In the first method both drugs are determined using first derivative UV spectrophotometry, with zero-crossing measurement. The second method depends on first derivative of the ratios spectra. The third method describes the use of multivariate spectrophotometric calibration for the simultaneous determination of the analyzed binary mixture where the resolution is accomplished by using partial least squares (PLS) regression analysis. In the fourth method (HPLC), a reversed-phase column and a mobile phase of methanol:water:acetonitrile (80:12:8 v/v/v/) at 0.9 ml/min flow rate have been used to separate both drugs with a UV detection at 270 nm. All the proposed methods are extensively validated. They have the advantage to be economic and time saving. All the described methods can be readily utilized for analysis of pharmaceutical formulations. The results obtained using the proposed methods are statistically analyzed and compared with some reported methods.     

Direct determination of closely overlapping drug mixtures of diflunisal and salicylic acid in serum by means of derivative matrix isopotential synchronous fluorescence spectrometry

A direct method for the simultaneous fluorimetric determination of two anti-inflammatory drugs in serum is proposed. The combination of matrix isopotential synchronous fluorescence (MISF) and first derivative technique provides good analytical results and permits the simultaneous determination of diflunisal and salicylic acid in human serum. MISF spectra are obtained by calculating the isopotential trajectory in the three-dimensional fluorescence spectrum for a serum solution. In the spectral contour, the trajectory is taken to be the portion of the line that passes by the fluorescence maxima of both compounds ensuring a sensitivity level similar to that of a direct determination in absence of background fluorescence. Analysis was carried out in water using a pH of 7.2 provides by 0.1 M sodium dihydrogen phosphate buffer. Serum samples are diluted 100 times and provide linear calibration plots at diflunisal and salicylic acid concentrations up to 800 ng mL⁻¹. The goodness of the analytical signal was checked by using variance analysis. Signals recorded throughout the calibration range were subjected to three calibrations per each analyte, both in the absence and in the presence of variable amounts of the other analyte. Differences between individual calibrations and slopes were compared with those within individual calibrations. Based on the results, diflunisal and salicylic acid can be accurately quantified in the presence of each other. The limit of detection calculated according to Clayton who uses error propagation throughout the calibration curve and a non-centralized security factor was 36.8 and 37.3 ng mL⁻¹ for diflunisal and salicylic acid, respectively.     

Partial least-squares with residual bilinearization for the spectrofluorimetric determination of pesticides. A solution of the problems of inner-filter effects and matrix interferents

This paper demonstrates for the first time the power of a chemometric second-order algorithm for predicting, in a simple way and using spectrofluorimetric data, the concentration of analytes in the presence of both the inner-filter effect and unsuspected species. The simultaneous determination of the systemic fungicides carbendazim and thiabendazole was achieved and employed for the discussion of the scopes of the applied second-order chemometric tools: parallel factor analysis (PARAFAC) and partial least-squares with residual bilinearization (PLS/RBL). The chemometric study was performed using fluorescence excitation-emission matrices obtained after the extraction of the analytes over a C18-membrane surface. The ability of PLS/RBL to recognize and overcome the significant changes produced by thiabendazole in both the excitation and emission spectra of carbendazim is demonstrated. The high performance of the selected PLS/RBL method was established with the determination of both pesticides in artificial and real samples.     

Determination of chlorprothixene and amitryptyline hydrochlorides by UV-derivative spectrophotometry and UV-solid-phase spectrophotometry

Two methods for spectrophotometric determination of chlorprothixene and amitryptyline hydrochlorides were proposed. One of them is based on spectral analysis of their derivative spectra. The measurement of the value at 316.0 nm of first derivative was used for construction of calibration graph for chlorprothixene. The Beer law was obeyed in the concentration range 0.5-50.0 microg ml(-1). The amplitude of the second derivative at 261.4 nm was used for determination of amitryptyline in the range 0.5-75.0 microg ml(-1). The second proposed method is utilized the use of solid sorbent for simultaneous preconcentration and assay of studied compounds. For this purpose the filtration gel Sephadex G100 was applied. The elaborated solid-phase spectrophotometric method was used for determination of chlorprothixene at 268.0 nm in the range 2.5-75.0 microg ml(-1) and amitryptyline at 238.0 nm in the concentration range 10.0-75.0 microg ml(-1).