Investigation of Protein Binding With All Solid‐State Ion‐Selective Electrodes

A potentiometric sensor for studying charge based adsorption of proteins was created using a single‐piece polyaniline‐PVC ion‐selective electrode (ISE). Three different ISEs, two for Na⁺ and one for Cl^? ion determination, were studied. The Na⁺‐ISEs consisted of a neutral calixarene‐based ionophore and one with a charged carrier dinonylnapthalenesulfonic acid (DNNSA) whereas for the Cl^? ISE, an anion exchanger tridodecylmethylammonium chloride (TDDMA⁺Cl^?), was used. The Na⁺ ISE with DNNSA as the charged carrier was successfully able to discriminate the binding of two different proteins (bovine serum albumin and lysozyme) based on their intrinsic charge.     

Oligocarbazoles as ligands for lead-selective liquid membrane electrodes.

Oligocarbazoles have been applied as new ionophores in liquid membrane electrodes (ISEs) destined for lead(II) determination in water samples. The oligocarbazole-containing ISEs demonstrated a close-to-Nernstian potentiometric response towards Pb2+ in the activity range 10(-7)-10(-2) M. The selectivity coefficients measured by the matched potential method (MPM) confirmed their good selectivity against common interfering mono- and doubly charged cations. The oligocarbazole-containing ISEs do not respond towards protons. Their applicability has been checked by performing the recovery test while using a sample of wastewater.     

Ion-selective electrodes for determination of organic ammonium ions: Ways for selectivity control

The influence of the ISE membrane composition on the selectivity for primary, secondary, tertiary, and quaternary alkylammonium cations, as well as for cations of physiologically active amines, has been investigated. Factors studied include the effect of plasticizer (2-nitrophenyl octyl ether, o-NPOE; dibutyl phthalate, DBP; dinonyl adipate, DNA; tris(2-ethylhexyl) phosphate, TEHP) and ion exchanger (potassium tetrakis(4-chlorophenyl)borate, K(TpClPB); potassium tris(nonyloxy)benzenesulfonate, K(TNOBS)), as well as that of the lipophilic cationic additive (tetradecylammonium nitrate, (TDA)NO(3)) and neutral carrier (dibenzo-18-crown-6) presence in membrane. It has been established that plasticizer nature affects K(i,j)(pot) values both when the target and/or foreign ions have non-ionic polar groups capable of specific interaction with plasticizer, and when the only difference consists in the substitution degree of their ionic groups. K(i,j)(pot) values for quaternary alkylammonium cations over primary-tertiary ones change in the following order: TEHP>DBP approximately DNA>o-NPOE. The highest K(i,j)(pot) value change is achieved for the primary-quaternary alkylammonium cation pair, amounting to 3 and 4.7 orders for membranes containing K(TNOBS) and K(TpClPB) as ion exchangers, respectively. In its turn, the ion exchanger influence on the selectivity depends on plasticizer nature, it being maximal for o-NPOE (about 2 orders) and practically non-existent for TEHP. On the whole, as compared to K(TpClPB)-based ISEs, those based on K(TNOBS) show higher selectivity for primary-tertiary alkylammonium cations over quaternary ones. Incorporation of (TDA)NO(3) into membrane causes further improvement of selectivity for primary-tertiary alkylammonium cations in the case of K(TNOBS) only. The maximal total effect of the ion exchanger and lipophilic ionic additive is observed for ISEs with DNA-plasticized membranes and is over 3 orders. The influence of crown ether on the selectivity also depends significantly upon ion exchanger and plasticizer nature. For ISEs with o-NPOE-plasticized membranes the K(i,j)(pot) value changes can be as great as 3 (ion exchanger K(TNOBS)) and even 4.5 (ion exchanger K(TpClPB)) orders. On the contrary, for ISEs with TEHP-plasticized membranes the crown ether effect on the selectivity is unessential. The results obtained are explained by peculiarities of organic ammonium cations solvating by plasticizer and association of cations with ion exchangers.     

The influence of the plasticizer nature on the selectivity of ion-selective electrodes to physiologically active amine cations: Regularities and abnormalities

The influence of the nature of plasticizer in the membrane of an ion-selective electrode (ISE) on its selectivity to cations of more than 20 physiologically active amines (PAA) is studied. It is found that an increase in the basicity of the plasticizer leads to a sharp increase in the membrane selectivity to PAA cations with lower degrees of the substitution of the salt-forming nitrogen atom, and also to PAA cations with nonionic polar groups capable of forming hydrogen bonds with Lewis bases. PAA cations forming intermolecular hydrogen bonds are an exception. The effect of the nature of the ion exchanger on the selectivity to PAA cations is strongest when plasticizers with low basicity are used; the selectivity of membranes with plasticizers of high basicity does not depend on the nature of the ion exchanger. For ISEs based on the neutral carrier dibenzo-18-crown-6 (DB-18-C-6), the best selectivity to primary amine cations in comparison to secondary and tertiary ones is achieved using plasticizers with low basicity.     

Synthesis, characterization, and complexation of tetraarylborates with aromatic cations and their use in chemical sensors

Five aromatic borate anions, namely tetrakis(4-phenoxyphenyl)borate (1), tetrakis(biphenyl)borate (2), tetrakis(2-naphthyl)borate (3), tetrakis(4-phenylphenol)borate (4), and tetrakis(4-phenoxy)borate (5), have been prepared and tested as ion-recognition sites in chemical sensors for certain aromatic cations and metal ions. To gain further insight into the complexation of the cations, some complexes have been prepared and structurally characterized. The complexation behavior of 1 and 2 towards N-methylpyridinium (6), 1-ethyl-4-(methoxycarbonyl)pyridinium (7), tropylium (8), imidazolium (9), and 1-methylimidazolium (10) cations has been studied, and the stability constants of the complexes of 1 with cations 6 and 8 have been measured to compare them with the values for the previously studied complexes of tetraphenylborate. The structures of the borate anions and their complexes have been characterized by NMR and mass spectrometric methods. X-ray crystal structures have been determined for potassium tetrakis(4-phenoxyphenyl)borate (K(+)1), N-methylpyridinium tetrakis(4-phenoxyphenyl)borate (61), 1-ethyl-4-(methoxycarbonyl)pyridinium tetrakis(4-phenoxyphenyl)borate (71), tropylium tetrakis(4-phenoxyphenyl)borate (81), and imidazolium tetrakis(biphenyl)borate (92). The results show that borate derivatives are potential candidates for a completely new family of charged carriers for use in cation-selective electrodes.     

New polyacrylate-based lead(II) ion-selective electrodes

A novel polyacrylate-based matrix for potentiometric ion-selective electrodes has been developed. Isododecyl acrylate, acrylonitrile and hexanedioldiacrylate co-monomers along with the thermo-initiator 2,2-dimethoxy-2-phenylacetophenone were used as polymeric matrix components. A lead(II)-selective electrode (Pb-ISE) was constructed using the above matrix. The electrode showed comparable analytical performance in the micromolar range to Pb-ISEs with conventional poly(vinyl chloride)-based membranes containing neutral ionophore and with solid-state membranes containing a mixture of lead sulphide and silver sulphide. Electrochemical impedance spectroscopy studies revealed much lower ion mobility in the polyacrylate membrane than in plasticized poly(vinyl chloride) membranes. This result additionally indicates the possibility of obtaining a lower detection limit for ISEs using the new acrylate matrix.     

Poly(Vinyl Chloride) Containing Dibenzo-18-crown-6 as an Ion-Selective Membrane for Hyamine 1622

Abstract

A poly(vinyl chloride) membrane ion-selective electrode for the Hyamine 1622 cation is proposed. The active substance of the electrode was the neutral carrier dibenzo-18-crown-6 and di-iso-octylphthalate was used as plasticizer. The electrode had a Nernstian behaviour between 6.0 × 10^?6 and 1.6 × 10^?3 mol/dm³, a pH working range of 2 – 12 and high selectivity towards inorganic cations. Among the organic cations tested, only those having surfactant properties did interface. The electrode was suitable for determining the critical micelle concentration and as end-point detector in the potentiometric titration of the cationic surfactants.     

Lipophilic ionic additive for controlling the selectivity of ion-selective electrodes reversible to cations of nitrogen-containing organic bases

The effect of a lipophilic ionic additive, a tetradecylammonium salt of a liquid ion exchanger, on the selectivity of ion-selective electrodes (ISEs) for cations of nitrogen-containing organic bases was studied. Additive-containing ISEs exhibited a higher selectivity for cations of primary to tertiary amines as compared to that for quaternary ammonium cations. A maximum change in selectivity (up to more than two orders of magnitude) due to the introduction of tetradecylammonium was observed for membranes containing dinonyladipate as a plasticizer and tris(nonyloxy)benzene sulfonic acid as an ion exchanger. In this case, the introduction of lipophilic ionic additive may lead to the reversal of the selectivity series. The effect of the lipophilic ionic additive on the selectivity of ISEs with membranes plasticized with o-nitrophenyl octyl ether decreased approximately by an order of magnitude. The selectivity of ISEs with the membranes containing tetrakis(4-chlorophenyl) borate as a cation exchanger was virtually independent of the presence of lipophilic ionic additives. The results obtained were explained by the peculiarities of ion-pair formation in the membrane.     

邻菲咯啉冠醚衍生物为载体的伯胺药物电极及机理研究

合成了邻菲咯啉-18-冠-6等四种含邻菲咯啉结构的冠醚化合物, 并用作载体制备伯胺电极, 以苄胺为模型化合物, 研究了电极特性, 并制备了测试美西律药物的选择性电极。研究了实验条件对电极性能的影响。用正交多项式回归法优化电极的膜组成。苄胺电极的线性范围1.0×10^-5~0.1mol/L, 斜率55.6mV/pc, 检测下限2.0×10^-6mol/L。美西律电极的线性范围6.0×10^-6~0.1mol/L, 检测下限8.0×10^-7mol, 斜率58.0mV/pc。同时研究了冠醚推动伯胺穿透大块液膜的传输行为。     

Polymeric membrane electrodes with improved fluoride selectivity and lifetime based on Zr(IV)- and Al(III)-tetraphenylporphyrin derivatives

Novel aluminum(III)- and zirconium(IV)-tetraphenylporhyrin (TPP) derivatives are examined as fluoride-selective ionophores for preparing polymer membrane-based ion-selective electrodes (ISEs). The influence of t-butyl- or dichloro-phenyl ring substituents as well as the nature of the metal ion center (Al(III) versus Zr(IV)) on the anion complexation constants of TPP derivative ionophores are reported. The anion binding stability constants of the ionophores are characterized by the so-called “sandwich membrane” method. All of the metalloporphyrins examined form their strongest anion complexes with fluoride. The influence of plasticizer as well as the type of lipophilic ionic site additive and their amounts in the sensing membrane are discussed. It is shown that membrane electrodes formulated with the metalloporphyrin derivatives and appropriate anionic or cationic additives exhibit enhanced potentiometric response toward fluoride over all other anions tested. Since selectivity toward fluoride is enhanced in the presence of both anionic and cationic additives, the metalloporphyrins can function as either charged or neutral carriers within the organic membrane phase. In contrast to previously reported fluoride-selective polymeric membrane electrodes based on metalloporphyrins, nernstian or near-nernstian (−51.2 to −60.1 mV decade⁻¹) as well as rapid (t < 80 s) and fully reversible potentiometric fluoride responses are observed. Moreover, use of aluminum(III)-t-butyltetraphenylporphyrin as the ionophore provides fluoride sensors with prolonged (7 months) functional lifetime.     

Glass and polymeric membrane electrodes for the measurement of pH in milk and cheese

While there is a considerable interest in the food industry in determining various analytes using ion-selective electrodes (ISEs), only few reports describe their use for direct measurements in food. In this study, the suitability of glass electrodes and ionophore-based solvent polymeric ISEs for the determination of pH in Process cheese, Cheddar cheese and milk was investigated. The liquid junction potential between a 3 M KCl bridge electrolyte and diluted as well as undiluted Process cheese was found to be negligible. Reference electrodes with ceramic plug and sleeve-type junctions performed well, although precautions needed to be taken to prevent plugging at the junctions. While the protein rennet casein posed no problems in pH measurements, the extraction of neutral lipophilic compounds or hydrophobic peptides into solvent polymeric membranes was evident, resulting in some loss of selectivity for monovalent cations upon exposure to cheese. However, it was found that ISEs based on tridodecylamine (R₃N) as ionophore and o-nitrophenyl octyl ether (oNPOE) as plasticizer can be used to accurately measure the pH of milk and, after desensitization of the electrodes in a cheese emulsion, of diluted Process cheese. Since pH measurements with a glass electrode showed that emulsions of cheese moderately diluted to a cheese content of 70% have the same pH as undiluted cheeses, it is possible to determine the pH in cheese with ionophore-based ISEs. R₃N membranes also performed well in undiluted milk.     

The synthesis and membrane transport characteristics of macrocyclic polyether ligands composed of 1,10-phenanthroline as carriers for primary amine species

Four macrocyclic polyether derivatives of o-phenanthroline were synthesized and used as neutral carriers for preparing poly(vinyl chloride) (PVC) membrane electrodes to sense primary amine species. The potentiometric response characteristics of the electrodes prepared were investigated. The electrode sensitive to benzyl amine as model analyte showed a linear response range of 8.0 x 10(-6)-0.1 mol/l with a detection limit of 8.9 x 10(-7) mol/l and a slope of 56.5 mV/decade. The linear potentiometric response of the mexiletine-sensitive electrode was 4.7 x 10(-6)-0.1 mol/l, and the detection limit was 5.0 x 10(-7)1 mol/l with a slope of 59.0 mV/decade. The transfer behavior of amines and ammonium ions through an organic phase was investigated by means of the bulk liquid membrane transport experiment. The effects of pH, counter anions and other factors on the transfer of the amine and ammonium species were studied. The mass transfer rates of the test species facilitated by macrocyclic polyether derivatives of o-phenanthroline were determined and the following sequence was found: benzyl amine > ethyl amine > tetramethyl ammonium > triethyl amine > diethyl amine > K(+) > ammonium > Na(+) > Ca(2+) > Mg(2+). This was exactly the potentiometric selectivity sequence of the membrane electrodes prepared by using these carriers. The mechanism of transfer of benzyl amine through a membrane phase induced by the carriers has been elucidated on the basis of experimental observations.     

Potentiometric response of poly(3-octylthiophene), poly(3-methylthiophene) and polythiophene in aqueous solutions

The potentiometric response of some polythiophenes in aqueous solutions has been investigated. Polythiophene (PT), poly(2,2'-bithiophene) (PBT), poly(3-methylthiophene) (PMT), poly(3-octylthiophene) (POT) and poly(4,4'-dioctyl2,2'-bithiophene) (POTd) were electrochemically deposited on platinum in 0.1M LiBF(4)-propylene carbonate solution containing the corresponding monomer or dimer. Polymer electrodes were also prepared by solution casting of chemically synthesized poly(3-octylthiophene) (POTc) dissolved in chloroform. After film deposition (electrochemical or chemical) the polymer coated electrodes were used as indicator electrodes in potentiometric measurements. The open-circuit potential of the polymer electrodes was measured in aqueous solutions containing inorganic salts (10(-1)-10(-4)M). Interestingly, all the polythiophenes studied were found to give a cationic response to monovalent cations such as H(+), Li(+), Na(+), K(+) and NH(+)(4) (Cl(-) salts). The slope, calculated from the linear part of the response curve, was found to depend on the polythiophene used but always remained lower than that predicted for a Nernstian response. The polythiophenes also showed some sensitivity to divalent cations such as Mg(2+) and Ca(2+) (Cl(-)-salts). POT was used as the polymer to study the influence of the polymerization conditions on the potentiometric response. By investigating different polymers from the polythiophene family it was possible to evaluate how the starting material (monomer or dimer) and the presence of alkyl side-chains influence the potentiometric response of the polymer membranes.     

新型杯芳烃为载体的铅离子选择电极

报道了5,11,17,23-四（1,1-二甲基乙基）-25,27-二羟基-26,28-二[（2-丙酰胺）乙氧基]杯[4]芳烃1的合成及以此化合物为载体研制了PVC膜铅离子选择电极。研究了不同极性的膜增塑剂和亲脂性阴离子位点对铅离子选择电极响应性能的影响,测定了铅离子选择电极的性能。铅离子选择电极对铅离子表现出优良的能斯特响应和高选择性,能在pH4.0-6.5的范围内使用,该电极可作为电位滴定的指示电极。     

Sulfonated poly(ether ether ketone) as an alternative charged material to poly(vinyl chloride) in the design of ion-selective electrodes

To date, poly(vinyl chloride) (PVC) is the most used polymer in the design of ion selective electrode (ISE) membranes. This paper is focused on the use of sulfonated poly(ether ether ketone) (SPEEK) as an alternative material to PVC for the design of ISEs. SPEEK of the desired degree of sulfonation is synthesized from poly(ether ether ketone) (PEEK). An NH₄⁺-ISE has been chosen as a model electrode to study the efficiency of SPEEK as polymer matrix of the membrane. The material was evaluated in ionophore free ion exchanger membranes as well as in ion-selective electrodes membranes containing nonactine as ionophore. Analytical performance parameters of the prepared electrodes were evaluated. The electrodes show a slope between 50 and 60 mV dec⁻¹ depending on both the calibration medium and the membrane composition. A linear range of response between 10⁻⁴ and 1.0 M and a lifetime of 1-2 months were obtained. The interferences of cations such us Ca²⁺, Na⁺, Li⁺ and K⁺ over the prepared ISEs are studied as well. Although the plasticizer in the SPEEK based membrane matrix is not necessary, its presence improves the sensibility. This makes SPEEK a good potential choice over alternative membrane matrices reported in the literature and a promising platform for the establishment of membrane components.     

Ion recognition: application of symmetric and asymmetric schiff bases and their complexes for the fabrication of cationic and anionic membrane sensors to determine ions in real samples

Schiff base compounds refer to the branch of supra-molecules and can be used as sensing material in the construction of potentiometric ion selective electrodes (ISEs). This relatively modern field has been subject to extensive research in the period of 1999-2007 when more than 100 ISEs employing Schiff bases were constructed. The quantitative high-throughput detection of 29 cations and 7 anions has been demonstrated in various scientific branches, such as biomedicine, pharmacy, biochemistry, pharmacology, environmental chemistry, food technology, and agriculture. This review discusses Schiff base compounds and their applications in the design and development of ion selective sensors and microsensors.     

A new sulfate-selective electrode and its use in analysis

The improvement of the steric accessibility of exchange centers of higher quaternary ammonium salts (QAS) by replacing several long-chain alkyl substituents at the nitrogen atom with methyl groups enhanced the selectivity of ion-selective electrodes (ISEs) based on the specified ion exchangers for the SO ₄ ^2? ion up to six orders of magnitude in the presence of singly charged anions. This can be qualitatively explained by the specific features of ion pair formation between quaternary ammonium cations and singly and doubly charged anions. The effect of the steric accessibility of the QAS exchange center on the selectivity of ISEs is partially retained in the presence of a neutral anion carrier, hexyl p-trifluoroacetylbenzoate (HTFAB), which is used for enhancing the selectivity for the sulfate ion in the presence of singly charged anions. A sulfate-selective electrode with a reasonable selectivity for practical purposes was proposed. It is based on the HTFAB-higher QAS ion pair bearing three methyl substituents at the nitrogen atom. The ISE was used in the analysis of natural water.     

Alkylation of benzyl chloride by gaseous carbenium ions

The alkylation of benzyl chloride has been studied in the gas phase using radiolytically formed carbenium ions as the charged reagents. The intramolecular selectivity of the electrophilic attack, deduced from the composition of the neutral products, is characterized by the comparable reactivity of the aromatic ring and of the halogen atom of the substrate toward the gaseous cations. As to ring alkylation, the reactivity of the ortho positions of benzyl chloride is considerably lower than those of chlorobenzene. The results are compared with pertinent mass-spectrometric data, and discussed in connection with existing models of gas phase aromatic substitution by charged electrophiles.     

Ionic liquid based on a quaternary phosphonium cation as a plasticizer and an electrode-active component of ion-selective electrode membranes

The dodecylethyldiphenylphosphonium bis(trifluoromethylsulfonyl)imide ionic liquid (IL) can behave as both a plasticizer and an electrode-active component in the membranes of ion-selective electrodes (ISEs). A stable potentiometric response to cationic surfactants is observed. The slope of the electrode function is close to the Nernstian value for cetylpyridinium (CP) bromide and cetyltrimethylammonium (CTMA) bromide; the detection limits are (5.0 ± 1.0) × 10^?6 and (1.3 ± 0.3) × 10^?5 mol/l, respectively. The membrane potential does not depend on pH in the range from 3 to 11. The possibility of determining the critical micelle concentration (CMC) with the ISEs is demonstrated.