Re-examination of the determination of ammonium as the indophenol blue complex using salicylate

The most sensitive spectrophotometric procedure for the determination of ammonium is based on the conversion of ammonium into the intense blue indophenol complex (IPC) by means of salicylate and nitroprusside. Optimization of concentration, preparation and timing of the addition of reagents, reaction temperature and protection from light increased the conversion of ammonium into IPC by about 50% compared with existing methods. The absorbance was 0.60 at a concentration of 20 nmol of ammonium per millilitre of final solution (RSD of the manual procedure=0.6%; n=10) with a detection limit of 0.4 μM in samples.     

Direct FIA-AS determination of potassium and magnesium in cement samples by use of the slurries approach

A direct procedure has been developed for the flame atomic determination of potassium and magnesium in cement samples. A 50-mg sample is dispersed in 25 ml of 0.13M nitric acid; 100 mul of this slurry is injected in a double channel FIA manifold simultaneously with 100 mul of a 10% (w/v) lanthanum solution. This procedure allows the rapid extraction of potassium and magnesium by leaching of the sample; nitric acid is not necessary if only potassium must be determined and the sample can be diluted with only distilled water. Aqueous standards are used. The manifold employed includes a well-stirred mixing chamber, which provides an adequate on-line dilution of the sample, in order to obtain emission or absorbance measurements in the dynamic range of the elements to be determined. The results obtained in the analysis of real samples agree with those found by flame atomic spectrometry after a previous alkaline fusion with lithium carbonate, and exhibit better precision. The limit of detection of the procedure is 0.007% for K(2)O and 0.01% for MgO and the precision of the entire procedure corresponds to a relative standard deviation of 1%.     

Sensitive determination of a glyoxal-DNA adduct biomarker candidate by column switching capillary liquid chromatography electrospray ionization mass spectrometry

A method based on column switching packed capillary liquid chromatography electrospray mass spectrometry has been developed for the determination of the adduct glyoxal-deoxyguanosine, a biomarker candidate for the assessment of glyoxal exposure, in DNA hydrolysate solutions. Microgram amounts of DNA were isolated and enzymatically hydrolyzed to deoxyribonucleosides, prior to ultrafiltration and subsequent dilution to a sample solution consisting of water-acetonitrile-formic acid (98 : 2 : 0.2, v/v). The sample solution was loaded onto a 1 mm I.D. x 5 mm Hypercarb (5 mum) porous graphitic carbon trap column for analyte enrichment using an injection volume of 200 mul, and was subsequently back-flushed onto a 0.30 mm I.D. x 150 mm Lichrospher diol (5 mum) analytical column. The samples were loaded with a flow rate of 40 mul min(-1) and glyoxal-deoxyguanosine was desorbed from the trap column and eluted with an isocratic mobile phase consisting of water-acetonitrile-formic acid (50 : 50 : 0.2, v/v) at a flow rate of 5 mul min(-1). Mass spectrometric determination of glyoxal-deoxyguanosine was obtained by multiple reaction monitoring of the transition [M + H](+)m/z 326 --> m/z 210. The method was evaluated over the concentration range 0.25-50 ng ml(-1) of glyoxal-deoxyguanosine in the hydrolysate of 5 mug DNA. The method was linear with a correlation coefficient of 0.9998 in this range. The within-day (n = 6) and between-day (n = 6) precisions were determined as 1.2-11% and 1.4-11% RSD, respectively, and the recovery was close to 100%. The mass limit of detection was 15 pg, corresponding to a concentration limit of detection of 75 fg mul(-1) DNA hydrolysate solution, corresponding to 48 adducts per 10(6) normal nucleosides. The method was applied for the determination of glyoxal-deoxyguanosine in DNA hydrolysate solutions of calf thymus DNA and cell cultures after reaction or incubation with glyoxal.     

Measurement of total alkali and phenol in process liquor by FIA

Flow injection analysis (FIA) has been applied to the determination of total phenol and total alkali in high concentration alkaline phenoxide liquors as it occurs in industrial process streams. The total alkali content and total phenol content in samples containing 20–50% (w/v) sodium phenoxide can be directly measured without mutual interference. The first is measured by peak width measurement based FIA with conductimetric detection utilizing an electronic circuit to permit automatic measurement from minima to minima. The total phenol is measured by the Berthelot reaction using NaOCl and ammonia to form indophenol blue, monitored at 660 nm with a light emitting diode-based detector.     

Square wave voltammetry assay of organophosphorus inhibition on cholinesterase in two phases of isooctane/water

A novel method for the detection of pesticides by inhibition of cholinesterase (ChE) from earthworm was developed. Two immiscible phases are employed where the organic phase isooctane contains substrate and the aqueous phase does enzyme. Water insoluble indophenol acetate was hydrolyzed by ChE at the interface of two phases to produce water soluble indophenol. The latter spontaneously penetrates into aqueous solution and gives the change of electrochemical signal. Organophosphorus compounds methyl parathion dissolved in isooctane phase could inhibit the activity of ChE at the interface of two phases and a corresponding inhibition relationship is given in the concentration range of 50 ng/ml–100 μg/ml.     

On-Line Solid Phase Extraction and Spectrophotometric Detection with Flow Technique for the Determination of Nanomolar Level Ammonium in Seawater Samples

The determination of low-level ammonium in seawaters suffers from low sensitivity and high contamination; therefore, it is desirable to develop highly sensitive methods for automatic measurements. A highly sensitive and automated flow technique system for nanomolar level ammonium measurement is described. Reagents for Berthelot reaction were automatically added into seawater samples. After a 10 min reaction at 40°C, the formed indophenol blue compound was on-line extracted onto an Hydrophilic-Lipophilic Balance (HLB) cartridge. The enriched compound was rinsed with water and ethanol solution (30%, v/v) and, in turn, eluted with an eluent containing 30% (v/v) ethanol and 5.0 mM of NaOH, and determined with a spectrophotometer at 640 nm. Parameter, including extraction conditions, reagent concentrations, pH, temperature, and reaction time, were optimized. Under the optimized conditions, the detection limit was 3.5 nM and the linear range was 0–428 nM. The relative standard deviations were 5.7% (n = 8) for 44.6 nM standard solution and less than 6.0% (n = 3–5) for samples within concentrations of about 52.4–288.7 nM; the recovery was in the range 93.6 to 108.5%. The sample throughput was 3 h^?1. The proposed method provides a simple, cheap, and automatic way to determine ammonium in seawater samples without complicated sample treatment.     

Determination of glycol in aircraft ground deicing/anti-icing fluids using flow injection with refractive index detection

A simple method for determining glycol in deicing/anti-icing fluids has been developed. The method uses a single line FIA system with detection based on Schlieren optics. The concentration range was 0-5% glycol and the limit of detection was 0.05%. Samples were preferably pumped at a flow rate of 0.7 ml/min and 100 mul of distilled water was injected (reverse FIA). Detection was accomplished with an 18 mul spectrophotometric flow cell at a wavelength of 410 nm. The conduit connecting the injector and the detector was 10 cm long and had an inner diameter of 0.5 mm. The traditional FIA approach can also be applied, i.e. injection of samples into a carrier of water, but the linear working range is narrower in comparison to the reverse FIA method. Standard addition and near infrared spectroscopy confirmed the validity of the developed method.     

Catalytic Kinetic Determination of Trace Amounts of Copper with Polarographic Detection

Abstract

This method is based on the catalytic effect of copper(II) on the redox reaction between acid chrome dark blue and ascorbic acid in acetic acid-sodium acetate buffer solution and 1,10-phenanthroline as an activator. Acid chrome dark blue exhibits a sensitive polarographic wave at -0.375V Vs. SCE and change of acid chrome dark blue concentration is traced by a polarographic detection technique. The detection limit and the linear range of copper(II) are 2.34ng/ml and 5 to 50ng/ml respectively. This new catalytic method has been applied to the determination of copper in human hair, with satisfactory results.     

Determination of l-malate in wine by flow-injection with co-immobilized malate dehydrogenase/oxaloacetate decarboxylase

A method for determination of l-malate in wine is described. Malate dehydrogenase and oxaloacetate decarboxylase were immobilized on poly (vinyl alcohol) beads and incorporated in a flow-injection system with fluorescence detection. Sample solution (50 mul) was injected into the carrier stream [4mM NAD(+) in glycine buffer (pH 10.0)]. The fluorescence based on the NADH formed could be directly related to the amount of malate. The calibration graph was linear over the range 0.4-300muM. The detection limit was 0.2muM. Sampling throughout was 25 samples/hr.     

Column-switching high-performance liquid chromatographic analysis of carbamazepine and its principal metabolite in human plasma with direct sample injection using an alkyl-diol silica (ADS) precolumn

In this paper, the on-line coupling of solid-phase extraction, based on a restricted-access support with high-performance reverse phase chromatography for the analysis of carbamazepine (CBZ) and carbamazepine-10,11-epoxide (CBZ-E) in human plasma samples is described. A precolumn packed with 25 mum C(18) alkyl-diol support is used for direct plasma injection. Using column-switching techniques, the analytes were enriched on the precolumn by a 5 mM phosphate buffer (pH 7) with 2% of methanol solution at a flow-rate of 0.8 ml min(-1), while proteins and endogenous hydrophilic substances in plasma were washed off to waste. The enriched analytes were then back-flushed onto the analytical C(18) column, separated by a mixture of 10 mM phosphate buffer (pH 7) acetonitrile (70:30 v/v) solution at a flow-rate of 1.0 ml min(-1) and detected by the ultraviolet absorbance set at 212 and 285 nm and without transfer loss. Linear calibration graphs were obtained for sample injection volumes of 50 (0.2-4.0 of mug of CBZ ml(-1) and 0.1-5.0 mug of CBZ-E ml(-1), respectively), and 20 mul (5.0-20.0 mug of CBZ ml(-1)); in either case the r-value was >0.9963. Recoveries from spiked plasma samples were quantitative for both analytes and the coefficients of variation were below 3.83%. The lowest samples concentrations that can be quantified with acceptable accuracy and precision was 0.2 mug CBZ ml(-1) and 0.1 mug CBZ-E ml(-1) when a sample volume of 50 mul was injected. Concentrations of 0.08 and 0.05 mug ml(-1) of CBZ and CBZ-E were considered the limit of detection for a signal-to-noise ratio of 3. Furthermore, the developed column-switching method was successfully applied to the determination of CBZ and CBZ-E in plasma samples of patients submitted to CBZ therapy.     

Photoacoustic spectroscopic studies on the solid phase cell with a differential type microphone using a diode laser as radiation source

The design and applications of the solid phase photoacoustic cell with a differential type microphone are described. This cell has higher sensitivity and reproducibility relative to a cell without a differential microphone. The method has been applied to the determination of phosphate ion in water samples. The detection limit for phosphate ion concentrated from 22.5 ml of sample solution on a membrane filter as molybdophosphate-n-dodecyltrimethylammonium bromide was 3.0 ng PO(3-)(4)/ml and the coefficient of variation for five measurements at 20 ng PO(3-)(4)/ml of phosphate ion was 3% using a diode laser (30 mW, 826 nm) as radiation source. The calibration graph for phosphate ion was linear over the range 5-50 ng PO(3-)(4)/ml.     

Flow injection analysis of nitrite by gas phase molecular absorption UV spectrophotometry

A flow injection method on the basis of gas phase molecular absorption is described for the determination of nitrite in the aqueous solution. 200 mul of nitrite solution is introduced into a carrier stream of distilled water. The carrier stream containing nitrite zone is reacted with a stream of hydrochloric acid (2 M). The stream is then segmented by O(2) gas. The produced gaseous products are purged into the O(2) segments, react with O(2) and are carried toward the gas-liquid separator. The gaseous phase is separated from the liquid stream by the use of home-made gas-liquid separator and then is swept into a home-made flow cell. The absorbance of gaseous phase is measured at 205 nm using a UV/VIS spectrophotometer. Under selected conditions, two linear ranges, up to 1000 mug ml(-1) and 1000-2000 mug ml(-1) of nitrite were obtained. The limit of detection was 7.5 mug ml(-1) NO(2)(-). The relative standard deviations of repeated measurements of 100 and 500 mug ml(-1) NO(2)(-) were 3.7 and 1.0%, respectively. Up to 30 samples h(-1) can be analyzed. Interferences in the proposed method were few and were readily overcome. The proposed method was successfully applied to the determination of nitrite in the spiked water samples, a number of meat products and urine.     

Photosensitization of different Candida species by low power laser light

The aim of this study was to evaluate the effects of the laser radiation (685 nm) associated with photosensitizers on viability of different species of Candida genus. Suspensions of Candida albicans, Candida dubliniensis, Candida krusei and Candida tropicalis, containing 10(6) viable cells per milliliter were obtained with the aid of a Neubauer's chamber. From each species, 10 samples of the cell suspension were irradiated with diode laser (685 nm) with 28 J/cm2 in the presence of methylene blue (0.1 mg/ml), 10 samples were only treated with methylene blue, 10 samples were irradiated with laser in the absence of the dye, 10 samples were treated with the dye and irradiated with laser light and 10 samples were exposed to neither the laser light nor to the methylene blue dye. From each sample, serial dilutions of 10(-2) and 10(-3) were obtained and aliquots of 0.1 ml of each dilution were plated in duplicate on Sabouraud dextrose agar. After incubation at 37 degrees C for 48 h, the number of colony-forming units (CFU/ml) was obtained and data were submitted to ANOVA and Tukey's test (p<0.05). Laser radiation in the presence of methylene blue reduced the number of CFU/ml in 88.6% for C. albicans, 84.8% for C. dubliniensis, 91.6% for C. krusei and 82.3% for C. tropicalis. Despite this, only laser radiation or methylene blue did not reduce significantly the number of CFU/ml of Candida samples, except for C. tropicalis. It could be concluded that the photo activation of methylene blue by the red laser radiation at 685 nm presented fungicide effect on all Candida species studied.     

Simultaneous determination of manganese and selenium in serum by electrothermal atomic absorption spectrometry

A method for determination of manganese and selenium in serum by simultaneous atomic absorption spectrometry (SIMAAS) is proposed. The samples (30 mul) were diluted (1+3) to 1.0% v/v HNO(3)+0.10% w/v Triton X-100 directly in the autosampler cups. A total of 20 mug Pd+10 mug Mg(NO(3))(2) was used as chemical modifier. The pyrolysis and atomization temperatures for the simultaneous heating program were 1200 and 2300 degrees C, respectively. The addition of an oxidant mixture (15% w/w H(2)O(2)+1.0% v/v HNO(3)) and the inclusion of a low temperature pyrolysis step (400 degrees C) attenuated the build-up of carbonaceous residues onto the integrated platform. An aliquot of 15 mul of the reference or sample solution was introduced into the graphite tube and heated at 80 degrees C; subsequently, 10 mul of oxidant mixture+10 mul of chemical modifier was introduced over that aliquot and the remaining heating program steps were executed. This strategy allowed at least 250 heating cycles for each THGA tube without analytical signal deterioration. The characteristic masses for manganese (6 pg) and selenium (46 pg) were estimated from the analytical curves. The detection limits were 6.5 pg (n=20, 3delta) for manganese and 50 pg (n=20, 3delta) for selenium. The reliability of the entire procedure was checked with the analysis of serum from Seronormtrade mark Trace Elements in Serum (Sero AS) and by addition and recovery tests (97+/-9% for manganese and 96+/-7% for selenium) using five serum samples.     

Sensitivity improvement of ammonia determination based on flow-injection indophenol spectrophotometry with manganese(II) ion as a catalyst and analysis of exhaust gas of thermal power plant.

The sensitivity improvement of a flow-injection spectrophotometric method for the determination of ammonia was examined based on an indophenol blue coloration reaction with salicylate and hypochlorite in the presence of manganese(II) as a reaction promotion catalyst. The optimal conditions for achieving higher sensitivity of ammonia determination were examined using a three-line flow system. The limit of detection corresponding to a signal-to-noise ratio (S/N) of 3 was 0.005 mg l(-1) (approximately equal to 5 ppb) of NH4+. A calibration graph was linear in the range from 5 ppb to 1,000 ppb of ammonium ion. The relative standard deviations (n = 9) for 50 ppb and 100 ppb of ammonium ion were 6.4% and 2.2%, respectively. The proposed method was applied to the determination of ammonia in the exhaust gas of a thermal power plant. Prior to the FIA determination, ammonia in the exhaust gas was absorbed into a boric acid solution; the absorption solution was then analyzed by the proposed FIA.     

Complexation of polyvinyl alcohol with iodine Analytical precision and mechanism

Polyvinyl alcohol (PVA), boric acid and tri-iodide form a characteristic blue complex. For a number of PVA samples, prescribed conditions were used to examine the precision of the formation and spectrophotometry of the complex. The precision of calibration curves was 1-2 % over the range 0-4 mg of PVA per 50 ml of final solution, over which Beer's law holds. Greater deviations can be caused by faulty preparation and aging of individual PVA solutions. The absorbance is independent of the content of residual acetate groups in the PVA for the range 0-15 %. The limit of detection is about 0.01 mg of PVA in 25 ml of sample. A pink colour in the system is due to association of iodine with acetate groups in the PVA. A blue or green colour is due to helical envelopment of iodine molecules by PVA chains stiffened by scattered cyclic groups. The mechanisms of these effects are discussed.     

Vapour phase Fourier transform infrared spectrometric determination of thiourea

A novel and precise procedure for the determination of thiourea based on vapour-generation Fourier transform infrared spectrometry is described. A 4 ml volume of 1.4% m/v iodine solution was injected into a glass vessel containing 5 ml of thiourea and 0.2 ml of 1 M sodium hydrogencarbonate solution. The CO2 evolved under these conditions was swept by a stream of nitrogen to an infrared gas cell. At 200 s after injection of the iodine solution, the vapour phase FTIR spectra were continously recorded, as a function of time, between 2500 and 2200 cm(-1), which includes the CO2 absorption band at 2350 cm(-1). From the absorbance data in the 2399-2284 cm(-1) range, integrated absorbance measurements were obtained providing transient recordings which correspond to the absorbance of CO2 in the selected wavenumber range. The method provided a limit of detection of 10 ppm of thiourea, a throughput of 14 samples h(-1) and an RSD of 1.1% for three independent analyses of a 500 ppm thiourea solution. Results obtained for a series of real samples compared well with those obtained using potentiometric titration as a reference method.     

Enzymatic Determination of Ammonia in Lake Water Using a Semi-Automatic Analyser

Abstract

An enzymatic method was developed for the determination of ammonia concentrations in lake water. Lake water samples containing ammonia were mixed with a glutamate dehydrogenase (GIDH), reduced nicotinamide adenine dinucleotide phosphate (NADPH) and 2-oxoglutarate. The decrease in the absorbance intensity caused by the disappearance of NADPH by this reaction was measured at 340 nm. There was a linear relationship (r = 0.9997) between peak height and ammonia concentration over the range 0–29 μM. The detection limit was 0.29 μM for a sample volume of 250 μl. Interference of amino acids and urea at concentrations of 50 mg l^?1 was negligible. Good agreement was found between the enzymatic method and indophenol blue colorimetry.     

Determination of trace chromium(VI) and molybdenum(VI) in natural and bottled mineral waters using long pathlength absorbance spectroscopy (LPAS)

A flow-through solid phase spectrophotometric (SPS) sensing device is proposed for the determination of minoxidil. The analyte is concentrated on Sephadex SP-C25 ion-exchanger packed in a flow cell and it is monitored by UV-Vis spectrophotometry at 282 nm, without derivatization reaction. When a HCl (10(-2) mol l(-1))/NaCl (5x10 (-2) mol l (-1)) solution is used as carrier/desorbing solution, the sensor responds linearly in the measuring range of 0.2-7, 0.1-4 and 0.05-2 mug ml(-1) with detection limits of 60, 33 and 6 ng ml(-1) for 600, 1000 and 2000 mul of sample, respectively. The relative standard deviations (%) for these volumes are 0.38, 1.06 and 2.63, respectively. The method was satisfactorily applied to the determination of minoxidil in pharmaceutical preparations and the results were compared with those obtained by high performance liquid chromatography (HPLC).     

Detection of nitrobenzene and related aromatics by reduction and indophenol formation

The detection of nitrobenzene is based on its partial reduction with zinc in slightly acidic medium to yield phenylhydroxylamine, acid-catalyzed rearrangement to form a mixture of 2- and 4-aminophenol, and formation of indophenol blue by 4-aminophenol on oxidative coupling with an alkaline phenol solution. The limit of detection is 0.1 μg ml^?1 nitrobenzene in the test solution. A positive test is also given by 2- and 3-nitrotoluene but various other aromatics containing nitro groups do not interfere. The method was tested on wastewaters.