Synthesis of superparamagnetic Mn3O4 nanocrystallites by ultrasonic irradiation

Nanocrystalline Mn₃O₄ has been synthesized by ultrasonic irradiation of Mn acetate solution in water. Analysis of its X-ray diffraction data shows formation of a phase-pure compound with an average particle size of about 15 nm. DC magnetization measurements as a function of temperature and field show a reduced ferrimagnetic transition temperature as compared to those reported for the bulk , and a subsequent observation of superparamagnetic behavior at 40 K. The observed magnetic properties are suggestive of formation of a single domain magnetically ordered Mn₃O₄ nanoparticles below their ferrimagnetic transition temperature.     

Formation of twinning-superlattice regions by artificial stacking of Si layers

We report about the formation of twinning-superlattice regions in Si epitaxial layers grown by molecular beam epitaxy on Si(1 1 1)()R30°-B surfaces. Twinning-superlattice regions were formed by periodical arrangement of 180° rotation twin boundaries along [1 1 1]-direction and are only separated by a few nanometers. The preparation method consists of repeating several growth, boron-deposition and annealing cycles on boron-predeposited undoped Si substrates. It is shown that the amount of subsurface boron and the growth mode influence the formation of twin boundaries. Only the nucleation of Si on the Si(1 1 1)()R30°-surface covered by at least ML boron results in the formation of 180° rotation twins. The size of superlattice regions is restricted by surface morphology. However, the presented technology should also be suitable to prepare a new type of semiconductor heterostructure based on Si polytypes.     

Growth and optical absorption spectra of ZnO films grown by pulsed laser deposition

ZnO films on Al₂O₃ substrate were grown by using a pulsed laser deposition method. Through photoluminescence (PL) and X-ray diffraction (XRD) measurements, the optimum growth conditions for the ZnO growth were calculated. The results of the XRD measurement indicate that ZnO film was strongly oriented to the c-axis of hexagonal structure and epitaxially crystallized under constraints created by the substrate. The full-width half-maximum for a theta curve of the (0 0 0 2) peak was 0.201°. Also, from the PL measurement, the grown ZnO film was observed to be a free exciton, which indicates a high quality of epilayer. The Hall mobility and carrier density of the ZnO film at 293 K were estimated to be 299 cm²/V sec and , respectively. The absorption spectra revealed that the temperature dependence of the optical band gap on the ZnO films was − .     

Crystallization of calcium oxalate monohydrate at dipalmitoylphosphatidylcholine monolayers in the presence of chondroitin sulfate A

The growth and aggregation of calcium oxalate monohydrate (COM) crystals beneath dipalmitoylphosphatidylcholine (DPPC) monolayers in the presence of chondroitin sulfate A (C₄S) was systematically examined under different surface pressure. The results indicated that the addition of C₄S can inhibit the crystal growth and prevent the aggregation of COM crystals. Under a DPPC monolayer, well-defined three-dimensional hexagonal prisms and three-dimensional rhombus prisms with sharply angled tips were obtained. The DPPC monolayer at a surface pressure of 10 mN/m can match the Ca²⁺ distance of the face of COM better than at 20 mN/m. The addition of C₄S could cooperatively modulate the interaction strength between the monolayer (or itself) with the specific morphology determining faces such as and (0 2 0), and thus results in remarkable stabilization of the faces. The dramatic changes in morphological details were due to the strong electrostatic interactions between the Ca²⁺-rich crystal faces of COM and the polyanionic polysaccharide C₄S together with the negatively charged sites of the zwitterionic DPPC monolayers. The increase of the concentration of C₄S can further enhance the stabilization of the face.     

Diffusion of Zn in stoichiometric LiTaO3

As stoichiometric LiTaO₃ (LT) draws a considerable attention for integrated optical waveguide devices, we have investigated Zn diffusion into this material by diffusing 70- nm-thick ZnO films deposited on y-cut LT substrates at 700–900 °C under various atmospheres. It was observed that the surface quality was very sensitive to pressure, but weakly affected by other diffusion conditions such as temperature and atmosphere. While the surface degraded, being covered with some residuals after heat treatment at the atmospheric pressure, it was very smooth and clear when the pressure was lowered below about 10 Torr. Another feature of Zn-diffused stoichiometric LT is that the crystal maintains its transparency even after diffusion at a pressure as low as 0.1 Torr, thus without a post-annealing step required. The diffusion coefficient varied from D=1.1×10^-2 to 5.5×10⁻¹ μm²/h in the given temperature range, with an activation energy of .     

Self-catalytic branch growth of SnO2 nanowire junctions

Multiple branched SnO₂ nanowire junctions have been synthesized by thermal evaporation of SnO powder. Their nanostructures were studied by transmission electron microscopy and field emission scanning electron microcopy. It was observed that Sn nanoparticles generated from decomposition of the SnO powder acted as self-catalysts to control the SnO₂ nanojunction growth. Orthorhombic SnO₂ was found as a dominate phase in nanojunction growth instead of rutile structure. The branches and stems of nanojunctions were found to be an epitaxial growth by electron diffraction analysis and high-resolution electron microscopy observation. The growth directions of the branched SnO₂ nanojunctions were along the orthorhombic [1 1 0] and . A self-catalytic vapor–liquid–solid growth mechanism is proposed to describe the growth process of the branched SnO₂ nanowire junctions.     

Growth of single crystals of the new double perovskite Ba2HoRu1−xCuxO6 from high temperature solutions

Single crystals of Ba₂HoRu_1−xCu_xO₆ have been grown from high temperature solutions using PbO–PbF₂ as solvent in the temperature range 1150–1250 °C. Crystals with a six sided plate like morphology measuring up to 3 mm across and 0.5 mm thick and polyhedral habit measuring up to 2 and 1 mm in thick mass were obtained. Powder X-ray diffraction patterns obtained on the crystals were indexed to give a monoclinic space group P2₁/n with lattice parameters a=5.875(2), b=5.874(3), c=8.960(1) and β=89.995(2)°. The crystals with x=0 show a single anomaly at 6.5 K corresponding to an antiferromagnetic phase with . The crystals containing Cu show additional anomalies at 18 and 48 K. The SEM and EDS analysis reveals a 2116 phase.     

Anisotropic vapor phase growth of Ga2O3 crystalline nanobelts

Ga₂O₃ nanobelts were synthesized by gas reaction at high temperature in the presence of oxygen in ammonia. X-ray diffraction and chemical microanalysis revealed that the nanostructures were Ga₂O₃ with the monoclinic structure. Electron microscopy study indicated the nanobelts were single crystalline with broad (0 1 0) crystallographic planes. The nanostructures grew anisotropically with the growth direction of . Statistical analysis of the anisotropic morphology of the nanobelts and electron microscopy investigation of the nanobelt tips indicated that both vapor–solid and vapor–liquid–solid mechanisms controlled the growth process. The anisotropic nature of crystallographic morphology is explained in terms of surface energy.     

Mechanochemical–hydrothermal synthesis of hydroxyapatite from nonionic surfactant emulsion precursors

Nanocrystalline hydroxyapatite [HA, Ca₁₀(PO₄)₆(OH)₂] powders were synthesized by the mechanochemical–hydrothermal method using emulsion systems consisting of aqueous phase, petroleum ether (PE) as the oil phase and biodegradable Tomadol 23–6.5 as the nonionic surfactant. (NH₄)₂HPO₄ and Ca(NO₃)₂ or Ca(OH)₂ were used as the phosphorus and calcium sources, respectively. The calcium source and emulsion composition had significant effects on the stoichiometry, crystallinity, thermal stability, particle size and morphology of final products. Disperse HA crystals with a 160 nm length and aspect ratio of ca. 6 were formed in an emulsion system containing 10 wt% PE, 60 wt% water and 30 wt% surfactant. The HA particles had needle morphology with a specific surface area of . With this technique, HA nanopowders with specific surface areas in the range of 72– were produced.     

Heteroepitaxy of CdTe on tilting Si(2 1 1) substrates by molecular beam epitaxy

CdTe(2 1 1)B epilayers were grown on 3 in Si(2 1 1) substrates which misoriented 0–10° toward [1 1 1] by molecular beam epitaxy (MBE). The relationship of X-ray double-crystal rocking curve (XRDCRC) FWHM and deflection angle from CdTe(2 1 1) to Si(2 1 1) was studied. For 4.2–4.5 μm CdTe, the best value of FWHM 83 arcsec was achieved while deflection angle is 2.76°. A FWHM wafer mapping indicated a good crystalline uniformity of 7.4 μm CdTe on tilting Si(2 1 1), with FWHM range of 60–72 arcsec. The shear strains of these epilayers were analyzed, using reciprocal lattice points of symmetric and asymmetric reflections measured by high-resolution multi-crystal multi-reflection X-ray diffractometer (HRMCMRXD). It was found that the shear strain angle of epilayer is effectively reduced by using proper tilting Si(2 1 1) substrate. It was also proved that the lattice parameter of CdTe(2 1 1)B is affected by the shear strain and thermal strain.     

Properties of ZnO films grown on (0 0 0 1) sapphire substrate using H2O and N2O as O precursors by atmospheric pressure MOCVD

In this paper, we compare the properties of ZnO thin films (0 0 0 1) sapphire substrate using diethylzinc (DEZn) as the Zn precursor and deionized water (H₂O) and nitrous oxide (N₂O) as the O precursors, respectively in the main ZnO layer growth by atmospheric pressure metal–organic chemical vapor deposition (AP-MOCVD) technique. Surface morphology studied by atomic force microscopy (AFM) showed that the N₂O-grown ZnO film had a hexagonal columnar structure with about 8 μm grain diameter and the relatively rougher surface compared to that of H₂O-grown ZnO film. The full-widths at half-maximum (FWHMs) of the (0 0 0 2) and () ω-rocking curves of the N₂O-grown ZnO film by double-crystal X-ray diffractometry (DCXRD) measurement were 260 and 350 arcsec, respectively, indicating the smaller mosaicity and lower dislocation density of the film compared to H₂O-grown ZnO film. Compared to H₂O-grown ZnO film, the free exciton A (FX_A) and its three phonon replicas could be clearly observed, the donor-bound exciton A⁰X (I₁₀):3.353 eV dominated the 10 K photoluminescence (PL) spectrum of N₂O-grown ZnO film and the hydrogen-related donor-bound exciton D⁰X (I₄):3.363 eV was disappeared. The electron mobility (80 cm²/V s) of N₂O-grown ZnO film has been significantly improved by room temperature Hall measurement compared to that of H₂O-grown ZnO film.     

Nucleation of AlN on SiC substrates by seeded sublimation growth

The nucleation of aluminum nitride (AlN) on silicon carbide (SiC) seed by sublimation growth was investigated. Silicon-face, 8 off-axis 4H-SiC (0 0 0 1) and on-axis 6H-SiC (0 0 0 1) were employed as seeds. Initial growth for 15 min and extended growth for 2 h suggested that 1850 °C was the optimum temperature of AlN crystal growth: on an 8 off-axis substrate, AlN grew laterally forming a continuous layer with regular “step” features; on the on-axis substrate, AlN grew vertically as well as laterally, generating an epilayer with hexagonal sub-grains of different sizes. The layer's c-lattice constant was larger than pure AlN, which was caused by the compression of the AlN film and impurities (Si, C) incorporation. Polarity sensitive and defect selective etchings were performed to examine the surface polarity and dislocation density. All the samples had an Al-polar surface and no N-polar inversion domains were observed. Threading dislocations were present regardless of the substrate misorientation. Basal plane dislocations (BPDs) were revealed only on the AlN films on the 8 off-axis substrates. The total dislocation density was in the order of when the film was 20– thick.     

Densities of Li2O–B2O3 melts

The densities have been systematically measured in xLi₂O–(1−x)B₂O₃ melts of different compositions with Li₂O content varying from x=0 to 0.68 from their respective melting points up to about 1450 K with a modified Archimedean method. The density decreased with increasing temperature for all the melts measured in this work. When x<0.15, the plot of temperature versus density could be well fitted by a quadratic polynomial function, and when x0.15, density decreased linearly with increasing temperature. At a fixed temperature, the density of the melts increased rapidly with Li₂O content, went through a maximum at about x=0.333 (Li₂O–2B₂O₃), and then decreased slowly as Li₂O content was further increased. In addition, the volume expansion coefficient (β) was calculated based on the densities measured in this work, and it was found that a maximum value appeared in the dependence of β on the molar ratio of Li₂O at about x=0.333.     

ZnO hexagonal prisms grown onto p-Si (1 1 1) substrate from poly (vinylpyrrolidone) assisted electrochemical assembly

Nonionic polymer poly (vinylpyrrolidone) (PVP) was firstly mixed into oxygenated zinc chloride electrolyte to modulate the crystal growth and morphology of ZnO from electrodeposition. Arrays of ZnO hexagonal prisms with well-defined (0 0 0 1) end facets and side facets were grown perpendicularly onto p-type Si substrates using the simple and economic route. It was observed that the concentration of PVP played an important role in the final morphology and size of ZnO crystals. The optical studies indicated that the addition of PVT not only influenced crystal growth habit but also improved the optical properties of ZnO.     

Some aspects on thermodynamic properties, phase diagram and alloy formation in the ternary system BAs–GaAs—Part I: Analysis of BAs thermodynamic properties

Owing to the lack of available thermodynamic data based on experimental measurements of heat capacity, decomposition reaction or vapour pressure measurements, the problem of BAs stability is considered. We propose a new set of thermodynamic data for enthalpy of formation, entropy and Gibbs free energy of Bas compound. By using thermodynamic database, our approach is based on the semi-empirical trends and analogy in the variation of those quantities for several binary series in different III–V systems like arsenides, nitrides and phosphides. Thus, the values for BAs were derived by extrapolation from Al to boron-based compounds (BAs, BP and, BN). For pure BAs(s), we predict a low enthalpy of formation in the standard state of at 300 K and a Gibbs free energy of indicating a lower stability of this compound than GaAs. Those values are contradictory discussed with trends in the cohesive energy of several III–V systems. A cohesive energy of 900 kJ/mol (9.4 eV) is proposed in agreement with Philips's rule.     

Controlled growth and kinetics of porous hydroxyapatite spheres by a template-directed method

Porous hydroxyapatite (HA) spheres with high purity of phase and well-controlled pore size were grown by a template-directed method. We studied for the initial concentration of Ca–P how to control the chemical component of the products, and for the concentration of template how to control the aperture and the morphology of porous HA spheres. The experimental results indicated that the lower concentration of Ca–P was prone to pure HA phase and the aperture decreased gradually with the increase of the concentration of template. Correspondingly, the crystallization thermodynamics and template-directed growth kinetics were discussed in details. The solubility isotherms of HA and dicalcium phosphate (DCPD) were calculated based on classical crystallization theories of thermodynamics. The results suggested that there was a critical concentration of in the case of Ca:P=5:3 and thus DCPD could be avoided only when in this given reaction system. Kinetic analysis of HA crystal growth revealed that the template depressed the interfacial potential energy E, then enhanced the roughness on the surface of crystal nucleus and directed HA crystal to selectively grow along the [0 0 0 1] direction, and consequently governed the aperture of porous HA spheres. The experimental results were in agreement with the theoretical analysis.     

Study on optimal growth conditions of a-plane GaN grown on r-plane sapphire by metal-organic chemical vapor deposition

Non-polar a-plane GaN thin films were grown on r-plane sapphire substrates by metal-organic chemical vapor deposition. In order to obtain a-plane GaN films with better crystal quality and surface morphology, detailed comparisons between different growth conditions were investigated. The results showed that high-temperature and low-pressure conditions facilitating two-dimensional growth could lead to a fully coalesced a-plane GaN layer with a very smooth surface. The best mean roughness of the surface morphology was 10.5 Å. Various thickness values of AlN nucleation layers and the V/III ratios for growth of the a-plane GaN bulk were also studied to determine the best condition for obtaining a smooth surface morphology of the a-plane GaN layer.     

Boron segregation control in silicon crystal ingots grown in Czochralski process

Boron-doped silicon single crystals of 207 mm diameter with various growing conditions are grown from a large amount of the melt in the cusp-magnetic Czochralski method, and the effects of growing parameters on dopant concentrations in the crystals are experimentally investigated. Equilibrium distribution coefficient of boron calculated by BPS model is 0.716. With the crystal rotation (ω) of 13 rpm and the crucible rotation of , the effective distribution coefficient (k_e) is 0.751 in zero magnetic strength and increases up to 0.78 in the magnetic strength of 640 G. For , there is no significant influence of ω on k_e. With , k_e is almost unity. The experimental results are compared with theory.     

Self-organized nanocomb of ZnO fabricated by Au-catalyzed vapor-phase transport

Based on a vapor-phase transport process, self-organized nanocomb structures of ZnO were fabricated on Au-coated Si substrate by employing a mixture of ZnO and graphite powders as source materials. The morphology of the product showed a ribbon-like stem and nanorod array aligned evenly along one side of the nanoribbon. It was found that the nanoribbon grew mainly along direction and the self-assembled branching nanorods grew epitaxially along [0 0 0 1] orientation from the (0 0 0 2) plane of the stem. The growth process was analyzed in detail.     

Porous crystal structures obtained from directionally solidified eutectic precursors

Interconnecting cage-like porous structures of several halide compounds were prepared by the selective leaching of one eutectic phase method. The binary eutectic precursors were prepared by directional solidification using the Bridgman crystal growth technique. Porous NaMgF₃ (40% pore volume), CaF₂ (57% pore volume) and BaF₂ (43% pore volume) crystals were obtained after water leaching the NaF component of the directionally solidified NaF/NaMgF₃, NaF/CaF₂ and NaF/BaF₂ eutectics with the appropriate entangled microstructure. The growth conditions for eutectic-coupled growth and the morphology of the eutectics have been determined. In the coupled growth regime, the size of the eutectic phases “λ” is fairly uniform and varies with the eutectic growth rate “v” as λ²v=constant, which allows us to control the pore size within the 0.5–10 μm range. The simplicity and versatility of the eutectic growth also allows us to fabricate highly aligned porous structures at relatively high production rates.