Miniaturized solid-phase extraction as a sample preparation technique for the determination of phthalates in water

Miniaturized solid-phase extraction (SPE) has been developed and successfully employed for the determination of organic species in water samples by liquid chromatography (LC). The method is based on the concept of a microscale extraction technique using a fused-silica capillary column for gas chromatography (GC), so-called in-tube solid-phase microextraction (SPME). The extraction conditions, such as the extraction time and flow-rate for the extraction and desorption process, were investigated as well as the effect of the internal structure of the extraction capillary on the efficiency. By inserting a stainless steel wire into the extraction capillary to reduce the internal volume of the capillary with the same surface area of the coating, an improved extraction and pre-concentration effects were obtained. Further pre-concentration was accomplished by the extraction device with a novel fiber-in-tube configuration. The direct coupling of the extraction method with a LC system has made it possible to determine low levels of phthalates in water samples without high consumption of organic solvents. The system developed must have potential applications for the analysis of environmental and biological samples in aqueous sample matrices.     

Arsenic determination in marine sediment using ultrasound for sample preparation.

This work deals with As determination in marine sediment using ultrasound for sample preparation. It is shown that As can be quantitatively extracted from marine sediment using 20% (v/v) HCl and sonication. The slurry is centrifuged and the analyte is determined in the supernatant by hydride generation atomic absorption spectrometry (HG AAS). A flow injection (FI) system is employed for hydride generation, with 0.5% (m/v) NaBH(4) used as reducdant and a 20% (v/v) HCl used as sample carrier. The limit of quantification is 1.6 microg g(-1) of As, which is based on 800 microl of sample solution and 0.200 g of sample mass in a volume of 50 mL. Certified and non certified marine sediment samples were analyzed; the results were in accordance with the certified or reference values. Speciation analysis by HPLC-ICP-MS showed that As(V) is the only detectable As species present in the supernatant of the centrifuged sample.     

Hemimicelle-based solid-phase extraction of estrogens from environmental water samples

Hemimicelles and admicelles of sodium dodecyl sulfate (SDS) on alumina and cetyltrimethyl ammonium bromide (CTAB) on silica were evaluated for the concentration and purification of the priority estrogens estrone (E(1)), 17beta-estradiol (E(2)) and ethynylestradiol (EE(2)) from sewage and river samples. Retention was based on analyte-sorbent hydrophobic and cation-pi interactions. Parameters affecting the SPE of estrogens on both types of sorbents were comparatively investigated. Adsolubilization was quantitative for SDS hemimicelles/admicelles and CTAB admicelles. SDS hemimicelle-coated alumina was the sorbent selected on the basis of the lower elution volume required and the higher sample flow rate allowed. Combination of estrogen adsolubilization-based SPE with liquid chromatography-diode array/fluorescence detection permitted the quantification of the target compounds with detection limits ranging from 20 to 100 ng l(-1). The relative standard deviation ranged from 3 to 8%. The approach developed was applied to the determination of estrogens in raw and treated sewage and river samples. The recovery found for estrogens in these environmental matrices was between 85 and 105%.     

Single-walled carbon nanohorn as new solid-phase extraction adsorbent for determination of 4-nitrophenol in water sample

Single-walled carbon nanohorn (SWCNH) was developed as new adsorbent for solid-phase extraction using 4-nitrophenol as representative. The unique exoteric structures and high surface area of SWCNH allow extracting a large amount of 4-nitrophenol over a short time. Highly sensitive determination of 4-nitrophenol was achieved by linear sweep voltammetry after only 120 s extraction. The calibration plot for 4-nitrophenol determination is linear in the range of 5.0 × 10⁻⁸ M-1.0 × 10⁻⁵ M under optimum conditions. The detection limit is 1.1 × 10⁻⁸ M. The proposed method was successfully employed to determine 4-nitrophenol in lake water samples, and the recoveries of the spiked 4-nitrophenol were excellent (92-106%).     

Study of applicability of various solid-phase extraction materials for sample handling in screening analysis of organic micropollutants in water.

At present, solid-phase extraction (SPE) has become an often preferred preconcentration technique in the screening for a wide range of organic micropollutants in water. A wide choice of materials available on the market makes SPE a suitable tool to cope with an increasing variability of organic compounds entering the hydrosphere. However, the interactions of various sorbent materials with compounds having different physico-chemical properties leads inevitably to large differences in preconcentration efficiency. The aim of this paper was to investigate the efficiency of preconcentration of selected organic compounds from aqueous solutions on various SPE materials. Simultaneously, the potential of newly emerging SPE procedures was compared to results of traditional liquid-liquid extraction methods. The group of 19 tested analytes was selected so as to represent different classes of organic compounds which may occur in waters. The results obtained showed that most of the tested materials were suitable for sufficient preconcentration of a substantial part of the tested analytes. However, specific differences in recovery of one or more analytes were found for almost each sorbent even in the case when the materials had similar composition. This behaviour clearly indicates the need for a thorough testing of capabilities of any SPE material intended for the use in a wide range screening method for the identification of unknown organic micropollutants in water.     

Comparison of solvent extraction and solid-phase extraction for the determination of organochlorine pesticide residues in water.

Solid-phase extraction (SPE) of organochlorine pesticide residues from environmental water samples was evaluated using octadecyl (C18)-bonded porous silica. The efficiency of SPE of these pesticide residues from reagent water samples at 1-5 micrograms dm-3 levels was compared with those obtained by solvent extraction with hexane and Freon TF (trichlorotrifluoroethane). Average recoveries exceeding 80% for these organochlorine pesticides were obtained via the SPE method using small cartridges containing 100 mg of 40 microns C18-bonded porous silica. The average recovery by solvent extraction with hexane and Freon TF exceeded 90% in both instances. It was concluded that the recoveries and precision for the SPE of organochlorine pesticides were poorer than those for the solvent extraction method. Organochlorine pesticide residue levels in environmental water samples from two major rivers flowing through predominantly rice-growing areas were monitored by gas chromatography using the solvent extraction method with hexane. Exceptionally high levels of organochlorine pesticide residues such as BHC, DDT, heptachlor, endosulfan and dieldrin were found in these water samples.     

Magnetic solid-phase extraction based on magnetic carbon nanotube for the determination of estrogens in milk

In this work, a novel method for the fabrication of magnetic carbon nanotubes based on 'aggregation wrap' was proposed. When carbon nanotubes and magnetic nanoparticles were vortically mixed in a solvent, the magnetic nanoparticles were wrapped into the carbon nanotube bundles that formed during the aggregation process, leading to the formation of magnetic carbon nanotubes. Thus, the resultant material can be separated from the solvent rapidly and conveniently by a magnet. Our investigation demonstrated that the 'aggregation wrap' mechanism for the preparation of magnetic composite is also applicable to other self-aggregated micro/nanomaterials, including graphene, graphite, C(60), etc. To testify the feasibility of the magnetic composites in sample preparation, the resultant magnetic carbon nanotubes were applied as sorbents for magnetic solid-phase extraction (MSPE) of estrogens in milk samples. Under optimized conditions, a rapid, convenient and efficient method for the determination of estrogens in milk samples was established by the combination of MSPE with high-performance liquid chromatography with fluorescence detector. The linearity range of the proposed method was 5-2000 μg/L with correlation coefficients (R) of 0.9983-0.9994. The limit of detection (LOD) for three estrogens ranged from 1.21 to 2.35 μg/L. The intra- and inter-day relative standard deviations (RSDs) were <9.3%. The reproducibility of the MSPE with different batches of magnetic carbon nanotubes was acceptable with RSD values <3.6%.     

固相萃取法与基质固相分散法在橙子中有机磷农药残留分析中的应用

建立了固相萃取(SPE)-反相高效液相色谱(RP-HPLC)同时测定橙子中痕量辛硫磷、二嗪农有机磷农药残留量的方法。样品经甲醇超声提取、C18固相萃取柱净化后,采用液相色谱柱分离,以乙腈-水(体积比为85∶15)为流动相等度洗脱,于254 nm下紫外检测。结果表明:在0.1～10.0 mg/L和0.4～10.0 mg/L范围内,辛硫磷、二嗪农的质量浓度与峰面积呈良好的线性关系;样品的加标平均回收率为87.3%～102.7%,相对标准偏差(RSD)为0.9%～4.9%。将该分析结果与用基质固相分散法(MSPD)处理样品所得的结果相比较,发现SPE对二嗪农的提取效果较好,而MSPD对辛硫磷的提取效果较好,但两种方法都能较好地净化样品,均能满足残留量的分析要求。     

Comparison of commercial solid-phase extraction sorbents for the sample preparation of potato glycoalkaloids

In this study five different commercial sorbents C18, SCX, CN, Certify and Oasis HLB were compared for the solid-phase extraction of potato glycoalkaloids. The recoveries were determined using alpha-solanine, alpha-chaconine and alpha-tomatine, which contained dehydrotomatine as an impurity, as standard compounds. The samples were analysed by reversed-phase liquid chromatography under gradient elution conditions using a Zorbax Rx-C18 column and acetonitrile-25 mM triethylammonium phosphate buffer (pH 3.0) as the mobile phase. The highest recovery (approximately 100%) was achieved with Oasis HLB (60 mg) cartridges. An acetic acid extract of wild Solanum brevidens leaf material was used for the testing of a clean-up procedure. The SCX proved to be the most selective and efficient for removing the undesired components from the leaf extract.     

Rapid monitoring and sensitive determination of DDT and its metabolites in water sample using solid-phase extraction followed by ion mobility spectrometry

Dichlorodiphenyl trichloroethane (DDT) as an organochlorine compound has been globally used as a pesticide for controlling soil-dwelling insects and treating diseases such as malaria and typhus. The degradation products of DDT and its metabolites have also negative effects on the environment. The present study has investigated the determination of DDT and its metabolites in water sample using ion mobility spectrometry (IMS) as a rapid and sensitive detection technique. For this purpose, DDT and its metabolites were extracted using reverse phase solid-phase extraction (SPE) from water samples. The samples were then recovered by eluting with methanol and finally, quantified using the corona discharge IMS technique. Injection and oven temperatures and the effect of dopant were optimized as experimental parameters influencing both detection and determination efficiencies. Degradation of DDT in IMS drift tube was studied and reduced mobility values of DDT and its metabolites were calculated. The developed method was validated using water sample to obtain good results for the determination of DDT at low levels (1 ng ml^?1) while spiked recoveries were obtained to be between 95.0–96.7%. The proposed method based on IMS proved to be a simple, inexpensive, rapid and sensitive procedure for the fast monitoring and determination of DDT and its main metabolites in water sample.     

Sample preparation for the chromatographic determination of ecdysteroids using solid-phase extraction methods

The ecdysteroids are hormones widely distributed in insects and crustaceans, where they are involved in the regulation of moulting. Methods of sample preparation based on solid-phase extraction of the ecdysteroids from biological samples for subsequent chromatographic analysis are reviewed. Most methods use an initial partition of the sample (or extract) between water or aqueous methanol with a non-polar solvent to remove lipids. The aqueous portion is applied to a cartridge containing C₁₈-bonded silica gel. Removal of polar impurities is then effected, followed by recovery of the ecdysteroids from the cartridge and chromatographic analysis. Results are given for the use of phenylboronic acid (PBA) bonded to silica gel as a means of obtaining a much more specific method of extraction. The PBA phase was shown to have a high affinity for ecdysteroids containing a 20,22-cis-diol but not for compounds possessing only a 2,3-cis-diol.     

Review of analytical methods for the determination of estrogens and progestogens in waste waters

Steroid sex hormones and related synthetic compounds, e.g. those used in contraceptive pills, have been shown to be present in the aquatic environment, mainly as a result of inefficient removal in waste-water-treatment plants (WWTP). The concentrations of the compounds, although very low (low ng L(-1)), are sufficient to induce estrogenic responses and alter the normal reproduction and development of wildlife organisms. The compounds have been determined, by a variety of analytical procedures, in the influents and effluents of WWTP, within research programs conducted in different countries to evaluate the efficiency of the waste-water-treatment processes currently in use. Determination of natural and synthetic estrogens and progestogens in waste water is, however, a difficult analytical task, because the very low detection limits required and the complexity of the waste-water matrix necessitate the execution of a considerable number of steps. Thus, in general, complicated, time-consuming extraction and purification processes, usually based on the application of solid-liquid extraction, are performed before final determination by immunoassay, high-performance liquid chromatography, or, most often, gas chromatography coupled with mass spectrometry. This paper reviews the analytical methods so far described for the analysis of these important environmental pollutants in waste water and discusses the key procedural steps, from sampling to analysis, and the techniques most commonly used in the determination.     

Use of packed-fiber solid-phase extraction for sample clean-up and preconcentration of vitamin B_(12) before determination

A rapid and simple preconcentration step applying packed-fiber solid-phase extraction columns has been investigated to vitamin B_(12).The extraction performance of the new method was investigated preliminarily on vitamin functional drink.The analysis used a reversed-phase C_(18) column,with a photo-diode array detector at 220 nm.The samples were preconcentrated with packed-fiber solid-phase extraction columns.Good linearity was observed in vitamin functional drink.The repeatability of extraction performa...     

An overview of sample preparation and extraction of synthetic pyrethroids from water,sediment and soil

The latest developments in sample preparation and extraction of synthetic pyrethroids from environmental matrices viz., water, sediment and soil were reviewed. Though the synthetic pyrethroids were launched in 1970s, to the best of authors’ knowledge there was no review on this subject until date. The present status and recent advances made during the last 10 years in sample preparation including conservation and extraction techniques used in determination of synthetic pyrethroids in water, sediment and soil were discussed. Pre- and post-extraction treatments, sample stability during extraction and its influence upon the whole process of analytical determination were covered. Relative merits and demerits including the green aspects of extraction were evaluated. The current trends and future prospects were also addressed.     

On-line coupling of solid-phase extraction to high-performance liquid chromatography for determination of estrogens in environment

A method based on on-line solid-phase extraction (SPE) coupling to high-performance liquid chromatography (HPLC) for the determination of estrogens has been developed. This method can continuously perform extraction of estrone, estradiol, estriol and diethylstilbestrol from aqueous samples without any other pretreatment, which can then be analyzed by HPLC with a UV detector at 230 nm. A pre-concentration column was adapted with methanol/water for chromatographic separation and two kinds of sorbents were involved, which are octadecyl-bonded silica and cigarette filter. The condition of pH of samples, sample loading flow rate and desorption time were all optimized, and the performances of both two sorbents were satisfactory. The on-line SPE system requires very low maintenance and just involved a switching-valve-filter system and a flow-inject pump, and the operation of the whole SPE-HPLC instrumentation is quite simple. The detection limits for pre-concentrating 50 mL of standard solution using cigarette filter as sorbent ranged from 0.98 to 78.1 ng L⁻¹. The enhancement factors were in the range of 197-326. The recoveries of estrogens spiked in real water samples ranged from 85 to 112%. The precisions for nine replicate measurements of a standard mixture (5.0 μg L⁻¹) were in the range of 1.0-3.4%.     

Miniaturized ternary deep eutectic solvent-based matrix solid-phase dispersion: A green sample preparation method for the determination of chlorophenols in river sediment

New ternary deep eutectic solvents were prepared and applied as efficient green dispersing solvents in miniaturized matrix solid-phase dispersion to extract chlorophenols from river sediments for the first time. High-performance liquid chromatography coupled with a photodiode array detector was used to analyze the target analytes. The significant factors affecting the extraction were optimized as follows: dispersant (100 mg), sample (100 mg), ternary eutectic solvents (150 μl), grinding for 1 min, 450 μl of acetonitrile as the elution solvent, and vortex mixing for 20 s. Under the optimal conditions, the method exhibited excellent linearity (correlation coefficient > 0.9980), low limits of detection between 1.039–2.478 μg/g, and extraction recoveries between 93.9% and 99.2%. Furthermore, the method demonstrated excellent precision in the intra- and inter-day analysis with a relative standard deviation below 6%. When compared to conventional extraction techniques, the miniaturized matrix solid-phase dispersion considerably reduced samples and solvent usag, offering important environmental benefits. The green profile of the method was assessed using the complementary green analytical procedure index tool confirming its eco-friendship. The technique was finally employed to evaluate sediment samples from three distinct locations along the Zuibaiji River, indicating its applicability for monitoring environmental samples.     

Simultaneous sample preparation for high-performance liquid chromatographic determination of Vitamin A and β-carotene in emulsified nutritional supplements after solid-phase extraction

Determination of small amounts of the fat-soluble species Vitamin A (VA) (2.5 μg/g) and β-carotene (9 μg/g) from emulsified nutritional supplements containing 50 kinds of co-existing compounds and a fat content between 2000 and 8000 times higher was performed by solid-phase extraction (SPE) and high-performance liquid chromatography (HPLC) with fluorescence detection set at ex. 350 nm and em. 480 nm, and visible detection at 450 nm using an Inertsil ODS 80A (5 μm) analytical column. Mobile phases of methanol-ethanol (50:50) and acetonitrile-ethanol (70:30) were used for the both vitamins. A Bond Elut C₁₈ cartridge was chosen for SPE after comparison with eight other types of SPE cartridge. Retention time of VA and β-carotene was 7 and 8 min, respectively, giving a limit of detection of ca. 0.1 ng per injection at a signal-to-noise ratio 3:1. Recoveries of VA and β-carotene were over 90% by the standard addition method. Relative standard deviation of VA and β-carotene were ca. 2.9 (n=5) and 2.3% (n=5), respectively.     

Alkaline extraction in combination with microwave-assisted extraction followed by solid-phase extraction treatment for polycyclic aromatic hydrocarbons in a sediment sample

Microwave-assisted extraction using 1 M KOH/methanol (alkaline-MAE) in combination with solid-phase extraction treatment was developed and applied to polycyclic aromatic hydrocarbons (PAHs) in a sediment sample. Although various conditions were examined (100 or 150 °C for 10 or 30 min), comparable concentrations of PAHs to those obtained by conventional extraction with 1 M KOH/methanol at 70 °C for 4 h were obtained, even at 100 °C for 10 min. The concentrations obtained by using MeOH at 150 °C for 30 min without KOH were lower (by 1.3-37%) than those obtained by alkaline-MAE at 150 °C for 30 min. Since the developed technique can introduce higher concentration of benzo[ghi]perylene relative to those using pressurized liquid extraction (toluene, 150 °C, 15 MPa, 10 min, two cycles), the developed alkaline-MAE is a effective technique.     

Estimation of measurement uncertainty for the determination of nonylphenol in water using solid-phase extraction and solid-phase microextraction procedures

We describe an estimation of measurement uncertainty calculated by the “bottom-up” approach for the determination of the oestrogenic compound nonylphenol in treated water samples by solid-phase extraction (SPE) and solid-phase microextraction (SPME) procedures and GC/MS detection. The results were compared and the different contributions to the uncertainty were evaluated. A study of the linear range was established and validation was performed for both methods using statistical analysis of several indicative parameters. In terms of validation data, precision (R.S.D. values <20%) and trueness (relative error <11%) were obtained for both methods under day-to-day conditions. The results of the estimation of measurement uncertainty obtained for both methods for concentrations higher than 1 μg/l have demonstrated that the time-consuming SPE method has a lower relative uncertainty (32%) than the SPME method (42.8%). The chromatographic uncertainty value was the main factor in the SPME method whereas the recovery factor (used to calculate the concentration) was the main contribution to uncertainty in the SPE method.