宽带光纤拉曼放大器的优化设计与分析

基于拉曼放大器的功率耦合方程 ,采用遗传算法和全局收敛的布雷登方法 ,提出一种优化设计不同形式反向抽运宽带光纤拉曼放大器的自动配置算法。该算法的特点是计算速度快 ,收敛性好 ,适应面广。通过对具有不同增益要求的分立式、单光纤分布式以及不同结构的色散管理式宽带拉曼放大器设计表明 :在 10THz的增益带宽内 ,放大器的增益平坦度均优于± 0 .6dB ,表明了该算法的可行性。通过对由标准单模光纤和色散补偿光纤构成的组合放大单元与色散管理光纤级链组成的放大单元的比较 ,表明色散管理式拉曼放大器具有潜在的应用价值。     

双向抽运光纤拉曼放大器的优化设计算法

基于双向抽运拉曼放大器的功率耦合方程 ,采用遗传算法和级链的全局收敛的Broyden方法 ,提出一种优化设计不同形式双向抽运宽带光纤拉曼放大器的自动配置算法。该算法的特点是计算速度快、收敛性好、适应面广。通过对单光纤的分布式、具有不同增益要求的分立式以及不同周期的色散管理结构的分布式双向抽运拉曼放大器的设计表明 :在 10THz的增益带宽内 ,放大器的增益平坦度均优于± 0 .6dB ,表明了该算法的可行性。此方法为采用双向抽运技术的拉曼放大器及其相应的全拉曼光纤传输系统的设计提供了一个公共平台     

A novel control method for on-off gain and gain tilt of fiber Raman amplifiers

Considering spectrum tilt due to signal-to-signal Raman scattering (SSRS) in backward distributed fiber Raman amplifiers (B-DFRA), an inverse tilted on-off gain profile is adopted to achieve flat net gain. A simple approximate linear relationship of pump power at each wavelength versus on-off gain level and tilt was derived numerically and experimentally so that a novel control method was established. Since there are only 3 pre-determinable constants required for individual pump wave, it is easy to be realized. As an example, maximum errors less than 0.2 and 0.4 dB respectively for average gain and gain tilt were achieved over C+L band in 100-km back-pumped standard single-mode fiber (SMF) experimentally.     

多波长抽运宽带光纤拉曼放大器的数值模拟与优化

采用平均功率分析算法对多波长抽运宽带光纤拉曼放大器进行了细致的数值模拟，并根据多抽运拉曼增益谱的特点和不同抽运波长对增益斜率的不同影响提出了一种新的有效的抽运优化算法，并利用这种方法对10波长抽运的光纤拉曼放大器进行了优化，获得了70nm带宽上增益谱波动低于0．5dB的结果。     

组合光纤中受激拉曼散射和四波混频研究

在抽运光和耦合条件不变的情况下,研究了熔接组合的非零色散位移单模光纤(NZDSF)和标准单模光纤(SMF)中的受激拉曼散射(SRS)和四波混频(FWM)产生和传输特征。采用532 nm脉冲激光抽运NZDSF,从20 m处开始产生以LP₀₁模传输的SRS第一级Stokes光;紧接着在30 m处产生了FWM,SRS受到FWM抑制,传输模式逐渐转化为LP₁₁模;经过80 m处熔接点后,由于熔接处双锥光纤结构使光场模式互相干涉,光波模式恢复为LP₀₁模,FWM受到抑制。该现象和机理有利于抑制密集波分复用(DWDM)系统中光学非线性失真和促进光孤子通信系统的发展。     

Noise performance analysis of bi-directionally pumped distributed fiber Raman amplifiers with consideration of fiber nonlinearity and its impact on EDFA output OSNR

Under small-signal assumption, equivalent noise figure normalized by fiber nonlinearities (NENF) of bi-directionally pumped distributed fiber Raman amplifiers (BiDFRA) is derived. Amplified spontaneous Raman scattering noise and double Rayleigh scattering noise are both included. The relation between NENF and Raman gain, forward Raman gain percentage is investigated under different polarization factor and Rayleigh scattering coefficient. It agrees well with numerical simulation results. Based on the analytical expression, the optical signal-to-nose ratio (OSNR) improvement of hybrid pre-BiDFRA/erbium-doped fiber amplifier (EDFA) compared with sole EDFA is studied. It is shown that there is an optimum Raman gain and forward Raman gain percentage to maximize the OSNR improvement. Finally, some guidelines on BiDFRA design are proposed.     

低泵浦功率的遥泵放大在超长跨距密集波分复用系统中的应用

针对长跨距密集波分复用系统中喇曼放大入纤泵浦功率过大的问题,将遥泵放大器（RP-EDFA）引入到系统中,通过对共纤RP-EDFA的噪音性能及其优化设计的研究,在理论上计算比较了RP-EDFA系统和后向喇曼放大系统在不同泵浦功率水平下的光信噪比和非线性相移,表明遥泵放大技术有效降低了入纤泵浦的功率水平,更适合长跨距应用.运用遥泵放大技术,对一个典型的长跨距系统进行系统Q值的模拟,结果表明：在 220 mW泵浦功率水平下可以实现跨距为 167 km的40×11.6 Gbit/s系统1000 km传输,Q值裕量4.4 dB.     

Optimal Configuration of Multiple Pump Powers and Wavelengths for Balanced Pre- and Post-pumped Raman Fiber Amplifiers

A novel configuration algorithm for bi-directionally pumped Raman amplifier is developed by adopting simulated annealing algorithm. Automatic design of optical fiber Raman amplifier using 10 laser diode pumps with different wavelengths and powers is demonstrated for 64 channels DWDM systems. The resulted gain ripple is less than 2.6 dB in amplification bandwidth of more than 50 nm for a transmission span of more than 300 km. The algorithm can be practically applied to desired signal channel number and gain profile.     

Optimal Configuration of Multiple Pump Powers and Wavelengths for Balanced Pre- and Post-pumped Raman Fiber Amplifiers

A novel configuration algorithm for bi-directionally pumped Raman amplifier is developed by adopting simulated annealing algorithm. Automatic design of optical fiber Raman amplifier using 10 laser diode pumps with different wavelengths and powers is demonstrated for 64 channels DWDM systems. The resulted gain ripple is less than 2.6 dB in amplification bandwidth of more than 50 nm for a transmission span of more than 300 km. The algorithm can be practically applied to desired signal channel number and gain profile.     

抽运方式对混合拉曼光纤放大器性能的影响

通过实验比较了前向抽运拉曼光纤放大器与掺铒光纤放大器组成的混合放大器、后向抽运拉曼光纤放大器与掺铒光纤放大器组成的混合放大器的性能。实验采用75km标准单模光纤作为增益介质。采用20信道(符合ITU-T建议的波分复用信号)，波长为1537．377～1560．605nm，作为混合放大器的测试信号。20信道总功率-2．86dBm，每一信道用2．5Gb／s、码长2^7-1的非归零码通过电吸收调制器(EA)进行外调制。实验结果表明，前向抽运方式混合放大器的性能优于后向抽运方式的混合放大器，其中噪声系数的改善值为2．28～6．55dB。采用前向抽运时，各信道的增益同后向抽运相比，增加值均大于5dB。但不论采取那种抽运方式，采用混合放大的形式，各信道的光信噪比均大于26．9dB。     

Amplification effect on SBS and Rayleigh scattering in the backward pumped distributed fiber Raman amplifier

The amplification effect on stimulated Brillouin scattering （SBS） and Rayleigh scattering in the backward pumped G652 fiber Raman amplifier （FRA） is studied. The pump source is a 1427.2-nm fiber Raman laser whose power is tunable between 0 - 1200 mW, and the signal source is a tunable narrow spectral bandwidth （〈 10 MHz） external cavity laser （ECL）. The Rayleigh scattering lines are amplified by the FRA and Stokes SBS lines are amplified by the FRA and the fiber Brillouin amplifier. The total gain of SBS lines is the production of the gain of Raman amplifier and that of Brillouin amplifier. In experiment, the SBS gain is about 42 dB and the saturation gain of 25-km G652 backward FRA is about 25 dB, so the gain of fiber Brillouin amplifier is about 17 dB.     

Amplification effect on stimulated Brillouin scattering in the S-band forward G652 fiber Raman amplifier

The amplification effects on forward and backward stimulated Brillouin scattering (SBS) lines in the forward pumped S-band distributed G652 fiber Raman amplifier (FRA) have been studied. There is a pump threshold power of Stokes backward stimulated Brillouin scattering (B-SBS) line in the forward pumped G652 FRA, it is about 1 mW. The Stokes B-SBS lines are amplified by FRA and fiber Brillouin Brillouin gain. In experimental work, the saturation gain of the first order Stokes backward SBS line is about 58 dB and the saturation gain of 25-km G652 forward FRA is about 25 dB, so the gain of FBA is about 33 dB. The forward stimulated Brillouin scattering (F-SBS) is generated and amplified in S-band G652 FRA. The stimulated threshold powers of the forward first order Stokes SBS (SB1-), second order Stokes SBS (SB2-), and third order SBS (SB3-) in the forward pumped FRA are 2.3, 1.6, and 1.6 mW,respectively. In experimental work, the saturation gains of SB1-, SB2-, and SB3- are about 38, 62, and 60 dB, respectively. The saturation Raman gain of 25-km G652 forward FRA is about 8.8 dB, so the Brillouin gains of SB1-, SB2-, and SB3- are about 29.2, 53.2, and 51.2 dB, respectively. The forward and backward cascaded SBS lines have been observed.     

双向抽运拉曼光纤放大器性能的研究

对双向抽运拉曼光纤放大器(RFA)的噪声特性、增益饱和及抽运功率转换效率进行了详细研究。结果表明,双向抽运拉曼光纤放大器的噪声特性介于前向抽运与后向抽运之间,但主要取决于前向抽运方式所导致的噪声特性;双向抽运方式的饱和功率低于单向抽运方式的饱和功率,同前向抽运与后向抽运提供的增益比例有关;双向抽运方式的抽运功率转换效率同信号光功率及前、后向抽运提供的增益有关,当信号光功率较低时,增加前向抽运的比例可取得较高的抽运功率转换效率,而信号光功率较高时,增加后向抽运的比例可取得较高的抽运功率转换效率。研究一种配置(情况3)的双向抽运拉曼光纤放大器,可以完全补偿100km传输线路的损耗(包括无源器件的损耗),最低光信噪比为30．21dB。     

Large-scale interferometric fiber sensor arrays with multiple optical amplifiers

We report what we believe to be the first laboratory prototype of a fiber sensor array using multiple low-gain (5dB) remotely pumped amplifiers in a 10-rung ladder structure. Incorporating amplifiers improves the system noise figure to less than 20dB, compared with 32dB in an optimized passive array of the same size. Scalability to more than 300sensors per fiber pair while a high dynamic range (1microrad/ sensitivity) is maintained is demonstrated.     

General and effective dynamic gain spectrum control of broadband raman amplifiers with multi-wavelength pumping

An effective feedback algorithm is proposed to dynamically control the gain spectra of multi-wavelength pumped broadband Raman amplifiers. Based on Raman coupling power equations, a simple saturation factor is introduced to achieve the adjusting matrix. By using this method, efficient pump adjustment can be carried out to accomplish wide-range dynamic gain spectrum control (larger than 22 dB dynamic range) as well as automatic gain clamping even for 90 nm bandwidth, highly-saturated RAs. Moreover, this algorithm can be well applied to different fiber types as well as pumping schemes. Some useful guidelines are also demonstrated.     

Remotely Pumped Hybrid Amplifiers for Extended Bidirectional Passive Optical Networks

In this contribution, we optimize design parameters of hybrid optical amplifiers utilizing distributed Raman amplification in transmission fiber and gain of discrete, remotely pumped erbium-doped fiber amplifier (EDFA) for wideband, bidirectional operation in metropolitan area networks (MAN). The design is based on an application of a numerical model, which takes into account pump-to-pump and signal-to-signal interactions and generation of amplified spontaneous emission in the Raman amplifier and solves the standard rate-propagation equations in an erbium-doped fiber (EDF). We predict 12 dB gain across 72 nm of optical bandwidth with gain ripple better than 10%. The recently proposed serial topology of EDFA is considered; this enables the wideband, bidirectional operation of a hybrid amplifier with only two pump laser diodes emitting in the 1430 and 1480 nm bands.     

Stimulated Raman scattering for variable gain amplification of small optically carried microwave signals

Stimulated Raman amplification of optically carried microwave signals in optical fibers is experimentally investigated. In the backward configuration which is shown to be less noisy than the forward one, net amplification factors larger than 20 dB are demonstrated in the low signal regime with better relative intensity noise (RIN) values than using erbium-doped-fiber amplifiers. Due to the RIN flatness with respect to the gain of the stimulated Raman amplifier high quality variable gain amplification of optically carried microwave signals could be implemented using optimized Raman amplifiers.     

Multi-wavelength fiber source based on double-pass superfluorescent fiber source and a reflection Mach-Zehnder filter

A spectrum-sliced multi-wavelength fiber source (SS-MWFS) based on double-pass superfluorescent fiber source (SFS) with a reflection Mach-Zehnder filter (RMZF) as the reflected comb filter is demonstrated.With backward pumped configuration, MWFS with 50 wavelength channels of extinction ratio (ER) of 16.7 dB is obtained over the almost total C-band gain region. Total output power of the MWFS is 16.2 mW which shows that a power of about 0.3 mW of per channel is achieved. The SS-MWFS with forward pumped configuration is also discussed for comparing. The backward pumped configuration can provide a larger output power while only a little smaller ER than that of the forward pumped configuration.     

增益平坦拉曼放大器优化算法研究

在分析受激拉曼散射耦合方程的基础上，介绍了一种反向设计多波长抽运光纤拉曼放大器的方法，并使用一种改进遗传算法和新型打靶法，讨论了体现特定的高增益和宽带平坦的适应度函数，对抽运波长和功率进行了优化，得到高增益，宽带平坦的增益谱，其开关增益可达15dB，增益带宽达80nm，增益波动小于1dB，这种放大器结构比现有的宽带光纤放大器在增益平坦上有一定的进步。     

Small-core As-Se fiber for Raman amplification

We have demonstrated Raman small-core As-Se fiber. More than 20-dB of gain was observed in a 1.1-m length of fiber pumped by a nanosecond pulse of approximately 10.8-W peak power at 1.50 microm. The peak of the Raman gain occurred at a shift of approximately 240 cm(-1). The Raman gain coefficient is estimated to be approximately 2.3 x 10(-11) m/W, which is more than 300 times greater than that of silica. The large Raman gain coefficient coupled with the large IR transparency window of these fibers shows promise for development of As-Se Raman fiber lasers and amplifiers in the near-, mid-, and long-IR spectral regions.