Polycation-sensitive membrane electrode for determination of heparin based on controlled release of protamine

A polycation-selective polymeric membrane electrode using dinonylnaphthalene sulfonate as an ion exchanger has been developed as a protamine controlled-release system for potentiometric detection of heparin. The incorporation of tetradodecylammonium tetrakis(4-chlorophenyl)borate as a lipophilic salt in the membrane dramatically improves the sensor's selectivity towards protamine over sodium ions via influencing the activity coefficient of protamine in the membrane, and a stable potential baseline can be obtained in the presence of an electrolyte background. The electrostatic binding interaction between heparin and protamine decreases the concentration of free protamine released at the sample-membrane interface and facilitates the stripping of protamine out of the membrane surface via the ion-exchange process with sodium ions, thus decreasing the membrane potential. Under optimal conditions, the proposed polymeric membrane electrode exhibits a linear relationship between the initial slope of the potential change and the heparin concentration in the range of 0.025-1.25 U mL(-1) with an improved detection limit of 0.01 U mL(-1).     

吡啶二羧酸根敏化LaF3:Tb发光纳米粒子的制备及对DNA的测定

采用水热法合成了水溶性良好的吡啶二羧酸根(DPA)敏化LaF3∶Tb(DPA-LaF3∶Tb)纳米粒子,该粒子的发光强度大且光学性能稳定.X射线衍射分析表明,合成了单一相六方晶系的LaF3晶体;透射电子显微镜结果表明,所合成粒子分散性良好,粒径约为15 nm.测得合成粒子在水相中的发光寿命为2.95 ms.以DPA-LaF3∶Tb纳米粒子为发光探针,基于DNA对纳米粒子的发光猝灭,实现了对DNA的定量测定,该方法的线性范围为0.083～13.0μg/mL;检出限为0.02μg/mL;并研究了共存物质对DNA测定的干扰.     

磁性石墨烯纳米粒子固相萃取与气相色谱-质谱相结合测定环境水样中的三嗪类除草剂

将磁性石墨烯作为磁性固相萃取的吸附剂与气相色谱-质谱(GC-MS)相结合建立了环境水样中7种三嗪类除草剂残留的测定新方法。对影响萃取效率的一些因素如吸附剂用量、萃取时间、样品溶液的pH值、离子强度和解吸条件等进行了优化。在优化的实验条件下,7种三嗪类除草剂的富集倍数在574~968之间。测定西玛津、扑灭津、嗪草酮、西草净、氰草津的线性范围为0.01~10.0 μg/L,莠去津的线性范围为0.05~10.0 μg/L,扑灭净的线性范围为0.01~8.0 μg/L。线性相关系数为0.9968~0.9998,检出限(S/N=3)为1.0~5.0 ng/L。将本方法应用于井水、自来水和湖水等实际水样的分析,在0.5 μg/L和2.0 μg/L下的加标回收率为79.8%~118.3%,相对标准偏差为3.6%~10.5%。该法操作简单、富集倍数高,可满足水样中三嗪类除草剂残留的检测要求。     

Preparation and Application of Magnetically Recoverable Cationic Exchanger Support on Monodisperse Fe<Subscript>3</Subscript>O<Subscript>4</Subscript> Nanoparticles

A magnetically recoverable cationic exchanger has been effectively prepared through immobilized chloroacetic acid (CA) onto the Fe₃O₄ nanoparticles. The magnetic nanoparticles (MNPs) were synthesized by a coprecipitation method in an aqueous system. The MNPs were modified with sodium silicate and chloroacetic acid (CA), thus endowed these nanoparticles with strong magnetism and good dispersion. The physicochemical properties of the cationic exchange materials were characterized with Fourier transform infrared spectroscopy (FTIR), transmission electron microscopy (TEM), X-ray diffraction (XRD) and thermal gravimetric analysis (TGA). The magnetic properties of the cationic exchange materials were analyzed by a vibrating sample magnetometer (VSM). The content of ions was measured by atomic absorption spectrophotometric method. The prepared cationic exchange nanoparticles display an excellent magnetic property with a saturation magnetization value of 26.58 emu/g and the prepared exchanger possess considerable thermal stability, which indicating a great potential application in heavy metal ion wastewater treatment. In this experiment, the exchange capacity of lead ion was 3.4 mmol g^–1, And the maximum lead removal rate is up to 73.85%.     

气相色谱-质谱法测定水中痕量的四乙基铅

建立了气相色谱-质谱(GC-MS)测定水中痕量四乙基铅的分析方法。用正己烷萃取水样中的四乙基铅,萃取液浓缩后加入同位素内标萘-d8,采用GC-MS选择离子方式(SIM)进行检测,在200 mL水样中四乙基铅的检出限可达0.04 μg/L;添加回收率为92.2%～103%,准确度好;平行5次测定的相对标准差为4.4%～13.3%。结果表明: 方法简便、快速、准确、实用,可用于水中痕量四乙基铅的测定。     

Multiple detection of proteins by SERS-based immunoassay with core shell magnetic gold nanoparticles

A highly selective and sensitive surface-enhanced Raman scattering (SERS)-based immunoassay for the multiple detection of proteins has been developed. The proposed core shell magnetic gold (Au) nanoparticles allow for successful protein separation and high SERS enhancement for protein detection. To selectively detect a specific protein in a mixed protein solution, we employed the sandwich type SERS immunoassay with core shell magnetic Au nanoparticles utilizing specific antigen–antibody interactions. Based on this proposed SERS immunoassay, we can successfully detect proteins in very low concentrations (∼800 ag/mL of mouse IgG and ∼5 fg/mL of human IgG) with high reproducibility. Magnetically assisted protein separation and detection by this proposed SERS immunoassay would provide great potential for effective and sensitive multiple protein detection. This technique allows for the straightforward SERS-based bioassays for quantitative protein detections.     

A Novel Magnetism‐assisted Electrochemical Immunosensor with Sub‐Picomolar Sensitivity

A novel electrochemical immunosensor based on a magnetic glassy carbon electrode (MGCE) was developed for the quantitative determination of human immunoglobulin G (IgG). The immunosensing interface was fabricated by initially depositing silver nanoparticles on the MGCE surface and then immobilizing anti‐human IgG antibodies via the magnetic force between MGCE and Fe₃O₄ nanoparticles. The antibodies were covalently bonded to the amine‐functionalized Fe₃O₄ nanoparticles. Under optimal conditions, the magnetism‐assisted immunosensor exhibited a wide linear range from 0.1 pg/mL to 1.0 µg/mL with the detection limit of 0.05 pg/mL. Furthermore, the immunosensor displayed the advantages of good reproducibility and satisfactory stability.     

Determination of catecholamines in urine using aminophenylboronic acid functionalized magnetic nanoparticles extraction followed by high‐performance liquid chromatography and electrochemical detection

A new method was developed for the simultaneous determination of three catecholamines in urine using aminophenylboronic acid functionalized magnetic nanoparticles extraction followed by high‐performance liquid chromatography with electrochemical detection. Novel aminophenylboronic acid functionalized magnetic nanoparticles were prepared by multi‐step covalent modification, and characterized by transmission electron microscopy, Fourier‐transformed infrared spectroscopy, X‐ray diffraction, and vibrating sample magnetometry. With the help of the high affinity between the boronate and cis‐diol group, the particles were used for the highly selective separation and enrichment of three major catecholamines, norepinephrine, epinephrine, and dopamine. Effects of the pH of the feed solution, the extraction time, the composition of the buffer solution, the amount of the magnetic particles, the elution conditions, and the recycling of aminophenylboronic acid functionalized magnetic nanoparticles were explored. Under the optimized conditions, 13–17‐fold enrichment factors were obtained. The linear ranges were 0.01–2.0 μg/mL for the studied analytes. The limits of detection and quantification were in the range of 2.0–7.9 and 6.7–26.3 ng/mL, respectively. The relative recoveries were in the range of 92–108%, with intraday and interday relative standard deviations lower than 6.8%. This method was successfully applied to analysis of catecholamines in real urine.     

Determination of benzoic acid in milk by solid-phase extraction and ion chromatography with conductivity detection

A simple, fast, precise and eco-friendly method, based on ion chromatography (IC) with a suppressed conductivity detector, was proposed for the determination of benzoic acid (BA) inmilk in this paper. The chromatographic separation was accomplished by using an anion exchange column eluted with 3.2 μmol/L aqueous Na2CO3 and 1.0 mmol/L aqueous NaHCO3 at a flow-rate of 0.7 mL/min. Themethod validation experiment provided excellent results with respect to linearity (correlation coefficient up to 0.9997), limit of detection (0.1 μg/L), recovery values (ranging from 88.0% to 93.0%) and relative standard deviation (RSD) (below 2.2%, n = 7).     

Carbonaceous nanomaterials immobilised mixed matrix membrane microextraction for the determination of polycyclic aromatic hydrocarbons in sewage pond water samples

In this study, the potential for carbonaceous nanomaterials to be used as adsorbents for the mixed matrix membrane (MMM) microextraction and preconcentration of organic pollutants was demonstrated. For this method, multiwall carbon nanotubes (MWCNT) and single layer graphene (SLG) nanoparticles were individually incorporated through dispersion in a cellulose triacetate (CTA) polymer matrix to form a MWCNT-MMM and SLG-MMM, respectively. The prepared membranes were evaluated for the extraction of selected polycyclic aromatic hydrocarbons (PAHs) present in sewage pond water samples. The extraction was performed by dipping a small piece of membrane (7 mm × 7 mm) in a stirred 7.5 mL sample solution to initiate the analyte adsorption. This step was followed by an analyte desorption into 60 μL of methanol prior to high performance liquid chromatography (HPLC) analysis. When the optimum SLG-MMM microextraction technique was applied to spiked sewage pond water samples, the detection limit of the method for the PAHs were in the range of 0.02–0.09 ng/mL, with relative standard deviations of between 1.4% and 7.8%. Enrichment factors of 54–100 were achieved with relative recoveries of 99%–101%. A comparison was also made between the proposed approach and standard solid phase extraction using polymeric bonded octadecyl (C₁₈) cartridges.     

固相萃取-超高效液相色谱-串联质谱法测定人指甲中的三氯生和三氯卡班

建立了人指甲中三氯生和三氯卡班的固相萃取结合超高效液相色谱-串联质谱(UPLC-MS/MS)检测方法。指甲样品经氢氧化钠消化,C18柱富集净化后,通过Waters ACQUITY^TM UPLC HSS T3色谱柱(100 mm×2.1 mm, 1.8 μm) 分离,以甲醇和水为流动相进行梯度洗脱,采用三重四极杆串联质谱仪负离子模式进行检测,同位素内标法定量。三氯生和三氯卡班分别在0.5~500.0 μg/kg和0.1~100.0 μg/kg范围内线性关系良好,相关系数(r²)均为0.999,方法定量限分别为2.0 μg/kg和0.2 μg/kg。3个水平的平均加标回收率为95.9%~110.2%,相对标准偏差为0.6%~9.7%(n=6)。本方法具有良好的灵敏度、回收率和重复性,适合指甲中痕量目标污染物的测定。利用该方法分析了60份实际样品,目标物的检出率为100%,三氯生和三氯卡班的含量范围分别为     

Superparamagnetic Composites Based on Ionic Resin Beads/CaCO3/Magnetite

The preparation of superparamagnetic composites obtained by CaCO₃ mineralization from supersaturate aqueous solutions is presented. The preparation was conducted in the presence of oleic acid stabilized magnetite nanoparticles as a water‐based magnetic fluid and insoluble templates as gel‐like cross‐linked polymeric beads. The presence of the magnetic particles in the composites provides a facile way for external manipulation using a permanent magnet, thus allowing the separation and extraction of magnetically modified materials. Two ion exchangers based on divinylbenzene/ethyl acrylate/acrylonitrile cross‐linked copolymer—a cation ion exchanger (CIE) and an amphoteric ion exchanger (AIE)—were used, as well as different addition orders of magnetite and CaCO₃ crystals growth precursors. The morphology of the composites was investigated by SEM, the polymorphs content by X‐ray diffraction, and the thermal stability by thermogravimetric analysis. Polymer, CaCO₃, and magnetite in the composite particles were shown to be present by energy dispersive X‐ray (EDX), XPS, and TEM. The sorption capacity for Cu^II ions was tested, as compared to samples prepared without magnetite.     

Amperometry of Heparin Polyion Using a Rotating Disk Electrode Coated with a Plasticized PVC Membrane

Electrochemical method of detection of heparin polyion was developed based on voltammetry of heparin on a rotating glassy carbon (GC) electrode coated with a plasticized PVC membrane. The membrane was deposited on the GC disk by spin‐coating technique using a mixture of solutions of PVC in tetrahydrofuran, and 1,1′‐dimethylferrocene (DMFc) and hexadecyltrimethylammonium tetrakis(4‐chlorophenyl)borate (HTMATPBCl) in o‐nitrophenyl octyl ether. UV/vis reflection spectrometry was used to evaluate the membrane thickness, which exhibits a linear correlation with the membrane resistance measured by impedance spectroscopy. It is shown that this electrode can be used for amperometric or coulometric detection of heparin in aqueous samples of medically relevant concentrations (1–10 U mL^?1), with a detection limit of 1.4 U mL^?1. Evidence is provided indicating that the current determining step is the reversible adsorption of the ion‐pair of heparin polyion with HTMA⁺ cation at the membrane/aqueous electrolyte interface, which is driven by oxidation of DMFc at the GC/membrane interface.     

RP-HPLC-UV validation method for levofloxacin hemihydrate estimation in the nano polymeric ocular preparation

The specific and accurate reversed-phase HPLC-UV method has been validated to determine levofloxacin hemihydrate (LEVH) level. The separation was conducted at C 18 analytical column by administering mobile phase acetonitrile, methanol, and phosphate buffer (pH 3) with the ratio of 17:3:80. The flow rate of the mobile phase was 1 mL/min with a UV detector at 295 nm wavelength. Analytical methods validation evaluated includes specificity, linearity, accuracy, precision, LOD, LOQ, and robustness. The implementation of the analytical method was employed to determine LEVH level in ocular polymeric nanoparticles preparations. The test was specific for LEVH with the retention time of 7.66 min. Linearity was obtained from the concentration range of 4.8 µg/mL to 29.04 µg/mL. All method validation criteria are within the acceptable range. The developed method can be applied for LEVH polymeric nano-formulation analysis.     

膜萃取-气相色谱/微分离子迁移谱检测水中的1,4-二恶烷

利用膜萃取-气相色谱/微分离子迁移谱（ME-GC/DMS）对水中的1,4-二恶烷污染物进行了检测。考察了射频电压、采样流速、膜渗透时间、Trap预富集时间等参数对检测二恶烷的影响规律。结果显示：在优化条件下,二恶烷的定量线性范围为2.0~20.0 μg/L,检出限为0.67 μg/L。实验证明,二恶烷与5种氯代烃的混合物在ME-GC/DMS的二维分离谱图中得到特异性响应,增加了识别的准确性。该研究为发展现场实时监测地下水中污染物的方法提供了重要参考。     

Magnetic solid‐phase extraction or dispersive liquid–liquid microextraction for pyrethroid determination in environmental samples

The determination of 15 pyrethroids in soil and water samples was carried out by gas chromatography with mass spectrometry. Compounds were extracted from the soil samples (4 g) using solid–liquid extraction and then salting‐out assisted liquid–liquid extraction. The acetonitrile phase obtained (0.8 mL) was used as a dispersant solvent, to which 75 μL of chloroform was added as an extractant solvent, submitting the mixture to dispersive liquid–liquid microextraction. For the analysis of water samples (40 mL), magnetic solid‐phase extraction was performed using nanocomposites of magnetic nanoparticles and multiwalled carbon nanotubes as sorbent material (10 mg). The mixture was shaken for 45 min at room temperature before separation with a magnet and desorption with 3 mL of acetone using ultrasounds for 5 min. The solvent was evaporated and reconstituted with 100 μL acetonitrile before injection. Matrix‐matched calibration is recommended for quantification of soil samples, while water samples can be quantified by standards calibration. The limits of detection were in the range of 0.03–0.5 ng/g (soil) and 0.09–0.24 ng/mL (water), depending on the analyte. The analyzed environmental samples did not contain the studied pyrethroids, at least above the corresponding limits of detection.     

超高效液相色谱-串联质谱法同时测定中成药和保健品中9种抗抑郁药物

建立了同时测定中成药和保健品中9种抗抑郁药物的超高效液相色谱-串联质谱（UPLC-MS/MS）分析方法。以甲醇为提取溶剂,超声提取,离心后取上清液,使用Waters ACQUITY UPLC BEH C₁₈色谱柱（100 mm×2.1 mm,1.7 μm）进行分离,以乙腈和0.1%（v/v）甲酸水为流动相对目标物进行梯度洗脱。在电喷雾正离子模式下,采用多反应监测（MRM）模式进行定性和定量分析。结果表明,9种抗抑郁药物在0.04~20 μg/L范围内线性关系良好,线性相关系数（R²）均大于0.998;目标物的检出限为0.0068~0.034 μg/L;在0.5、1、5 μg/L 3个添加水平下的平均回收率为77.7%~100.8%,相对标准偏差为0.9%~9.1%。本方法准确、简便、快速,可用于中成药和保健品中抗抑郁药物的检测。     

Efficient and selective separation of metronidazole from human serum by using molecularly imprinted magnetic nanoparticles

Magnetic molecularly imprinted nanoparticles were prepared through surface‐initiated reversible addition fragmentation chain transfer polymerization by using metronidazole as a template. The molecularly imprinted magnetic nanoparticles were characterized by attenuated total reflection Fourier transform infrared spectroscopy, X‐ray photoelectron spectroscopy, transmission electron microscopy, X‐ray diffraction, and vibrating sample magnetometry. The adsorption characteristics were also investigated and the kinetics of the adsorption of metronidazole on the imprinted nanoparticles were described by the second‐order kinetic model with the short equilibrium adsorption time (30 min). The adsorption isotherm was well matched with the Langmuir isotherm in which the maximum adsorption capacity was calculated to be 40.1 mg/g. Furthermore, the imprinted magnetic nanoparticles showed good selectivity as well as reusability even after six adsorption–desorption cycles. The imprinted magnetic nanoparticles were used as a sorbent for the selective separation of metronidazole from human serum. The recoveries of metronidazole from human serum changed between 97.5 and 99.8% and showed similar sensitivity as an enzyme‐linked immunoassay method. Therefore, the molecularly imprinted magnetic nanoparticles might have potential application for the selective and reliable separation of metronidazole from biological fluids in clinical applications.     

Controlled assembly of superparamagnetic iron oxide nanoparticles on electrospun PU nanofibrous membrane: A novel heat-generating substrate for magnetic hyperthermia application

A facile method of fabricating novel heat-generating membranes composed of electrospun polyurethane (PU) nanofibers decorated with superparamagnetic iron oxide nanoparticles (NPs) is reported. Electrospinning was used to produce polymeric nanofibrous matrix, whereas polyol immersion technique allowed in situ assembly of well-dispersed Fe₃O₄ NPs on the nanofibrous membranes without any surfactant, and without sensitizing and stabilizing reagent. The assembly phenomena can be explained by the hydrogen-bonding interactions between the amide groups in the PU matrix and the hydroxyl groups capped on the surface of the Fe₃O₄ NPs. The prepared nanocomposite fibers showed acceptable magnetization value of 33.12 emu/g, after measuring the magnetic hysteresis loops using SQUID. Moreover, the inductive heating property of electrospun magnetic nanofibrous membranes under an alternating current (AC) magnetic field was investigated. We observed a progressive increase in the heating rate with the increase in the amount of magnetic Fe₃O₄ NPs in/on the membranes. The present electrospun magnetic nanofibrous membrane may be a potential candidate as a novel heat-generating substrate for localized hyperthermia cancer therapy.     

In situ synthesis of polysaccharide nanoparticles via polyion complex of carboxymethyl cellulose and chitosan

Biocompatible polymer-magnetite hybrid nanoparticles were prepared by means of in situ synthesis of magnetite within polysaccharide hydrogel nanoparticles. Hydrogel nanoparticles were first fabricated by blending high-molecular-weight carboxymethyl cellulose as an anionic polymer, and low-molecular-weight chitosan as a cationic polymer to form polyion complexes (CC particles). These polyion complexes were then chemically crosslinked using genipin, a bio-based cross-linker, to form stable nanoparticles having a semi-IPN structure (CCG particles). Magnetite was lastly synthesized within CCG particles by the coprecipitation method to obtain polymer-magnetite hybrid nanoparticles (CCGM particles). The formations of CC, CCG and CCGM particles were mainly observed by transmittance, absorbance of genipin and TEM, respectively, and their hydrodynamic diameters and zeta-potentials were analyzed. It was confirmed that the hydrodynamic diameters and the zeta-potentials of these particles were significantly influenced by pH of the suspension, which was attributed to the charges of polymers. The diameters of CCGM particles were smaller than 200 nm at any pH conditions, suggesting the possibility to apply them as drug delivery carriers. CCGM particles exhibited the responsiveness to a magnetic field in addition to their high dispersion stability, indicating their potential to be utilized as a biomaterial for hyperthermia.