Continuous‐Flow Synthesis of CdSe Quantum Dots: A Size‐Tunable and Scalable Approach

In recent years, continuous‐flow/microreactor processing for the preparation of colloidal nanocrystals has received considerable attention. The intrinsic advantages of microfluidic reactors have opened new opportunities for the size‐controlled synthesis of nanocrystals either in the laboratory or on a large scale. Herein, an experimentally simple protocol for the size‐tunable continuous‐flow synthesis of rather monodisperse CdSe quantum dots (QDs) is presented. CdSe QDs are manufactured by using cadmium oleate as cadmium source, selenium dioxide as selenium precursor, and 1‐octadecene as solvent. Exploiting selenium dioxide as selenium source and 1‐octadecene as solvent allows execution of the complete process in open air without any requirement for air‐free manipulations using a glove box or Schlenk line. Continuous‐flow processing is performed with a stainless steel coil of 1.0 mm inner diameter pumping the combined precursor solution through the reactor by applying a standard HPLC pump. The effect of different reaction parameters, such as temperature, residence time, and flow rate, on the properties of the resulting CdSe QDs was investigated. A temperature increase from 240 to 260 °C or an extension of the residence time from 2 to 20 min affords larger nanocrystals (range 3–6 nm) whereas the size distribution does not change significantly. Longer reaction times and higher temperatures result in QDs with lower quantum yields (range 11–28 %). The quality of the synthesized CdSe QDs was confirmed by UV/Vis and photoluminescence spectroscopy, small‐angle X‐ray scattering, and high‐resolution transmission electron microscopy. Finally, the potential of this protocol for large‐scale manufacturing was evaluated and by operating the continuous‐flow process for 87 min it was possible to produce 167 mg of CdSe QDs (with a mean diameter of 4 nm) with a quantum yield of 28 %.     

Green chemistry for large-scale synthesis of semiconductor quantum dots

Large-scale synthesis of semiconductor nanocrystals or quantum dots (QDs) with high concentration and high yield through simultaneously increasing the precursor concentration was introduced. This synthetic route conducted in diesel has produced gram-scale CdSe semiconductor quantum dots (In optimal scale-up synthetic condition, the one-pot yield of QDs is up to 9.6g). The reaction has been conducted in open air and at relatively low temperature at 190-230 degrees C in the absence of expensive organic phosphine ligands, aliphatic amine and octadecene, which is really green chemistry without high energy cost for high temperature reaction and unessential toxic chemicals except for Cd, which is the essential building block for QDs.     

PbSe/CdSe and PbSe/CdSe/ZnSe hierarchical nanocrystals and their photoluminescence

Multiple CdSe and ZnSe semiconductor shells were grown on PbSe semiconductor spherical cores with monolayer control. For CdSe shell coating, we found that there was little room to further increase the quantum yields of freshly-made high-quality PbSe nanocrystals that already owned very high initial values because of their good surface status; but there was great improvement for the PbSe nanocrystals with low initial quantum yields because of the poor surface status. Nonetheless, the quantum yield for the latter case could not reach the former's value. Additional ZnSe shells on PbSe/CdSe could further increase the quantum yield and protect the nanocrystals from air oxidation. The observed phenomena in the synthesis of the PbSe/CdSe and PbSe/CdSe/ZnSe core/shell structures were explained through the carrier wave function expansion and the surface polarization.     

无膦方法合成高质量CdSe纳米晶及其光学性质

以合成的十碳酸镉作为Cd前驱体, 十八烯作为单质硒溶剂, 并添加十八胺作为活性剂, 在无三丁基膦或三辛基膦参与的条件下, 以较低温度制备了具有闪锌矿结构的高质量的CdSe纳米晶. 利用吸收光谱、荧光光谱(PL)、X射线衍射(XRD)、透射电镜(TEM)对不同反应时间得到的CdSe纳米晶进行形貌和光谱性质表征. 实验结果表明, 采用该无膦法只需调控反应时间就可得到粒径均一、分散性好的CdSe纳米晶, 其荧光波长可覆盖470-630 nm的可见光区, 而荧光峰半高宽则始终保持在24-30 nm之间并具有较高的荧光量子产率(535 nm处大于60%). 最后, 对CdSe纳米晶量子产率随反应时间变化的原因进行了分析.     

Highly Stable CdSe/CdS/ZnS Fluorophores in Acidic Environment: Acile Preparation and Modification of Core/shell/shell Nanocrystals

We described a facile method for preparing CdSe/CdS/ZnS core/shell/shell nanocrystals from air-stable single source precursors.The single source precursors of cadmium ethylxanthate and zinc ethylxanthate were used to form CdS and ZnS shell layers in octadecene.An efficient modification of CdSe/CdS/ZnS nanocrystals was subsequently performed to obtain hydrophilic nanocrystal fluorophores with good stability in a pH range of 1.6-10.     

Synthesis of nanocrystals via microreaction with temperature gradient: towards separation of nucleation and growth

By utilizing the symmetrical temperature distribution in a tube furnace chamber, a capillary microreactor was designed with the microchannel passing two well-controlled, stable temperatures in steep temperature gradients. The two-temperature microreator, first developed and implemented by this research team, provides an opportunity to separate the nucleation and growth of semiconductor nanocrystals, leading to better control of nucleation and growth kinetics. For the synthesis of CdSe nanocrystals as a model system, we demonstrated the improved size uniformity achieved by the two-temperature approach, confirming the success of the use of high temperature to burst nucleation and low temperature to promote growth.     

Effects of viscosity on droplet formation and mixing in microfluidic channels

This paper characterizes the conditions required to form nanoliter-sized droplets (plugs) of viscous aqueous reagents in flows of immiscible carrier fluid within microfluidic channels. For both non-viscous (viscosity of 2.0 mPa s) and viscous (viscosity of 18 mPa s) aqueous solutions, plugs formed reliably in a flow of water-immiscible carrier fluid for Capillary number less than 0.01, although plugs were able to form at higher Capillary numbers at lower ratios of the aqueous phase flow rate to the flow rate of the carrier fluid (in all the experiments performed, the Reynolds number was less than 1). The paper also shows that combining viscous and non-viscous reagents can enhance mixing in droplets moving through straight microchannels by providing a nearly ideal initial distribution of reagents within each droplet. The study should facilitate the use of this droplet-based microfluidic platform for investigation of protein crystallization, kinetics, and assays.     

Formation of droplets and bubbles in a microfluidic T-junction-scaling and mechanism of break-up

This article describes the process of formation of droplets and bubbles in microfluidic T-junction geometries. At low capillary numbers break-up is not dominated by shear stresses: experimental results support the assertion that the dominant contribution to the dynamics of break-up arises from the pressure drop across the emerging droplet or bubble. This pressure drop results from the high resistance to flow of the continuous (carrier) fluid in the thin films that separate the droplet from the walls of the microchannel when the droplet fills almost the entire cross-section of the channel. A simple scaling relation, based on this assertion, predicts the size of droplets and bubbles produced in the T-junctions over a range of rates of flow of the two immiscible phases, the viscosity of the continuous phase, the interfacial tension, and the geometrical dimensions of the device.     

Thiol-stabilized CdSe and CdTe nanocrystals in the size quantization regime: Synthesis,optical and structural properties

We report on the recently developed method for the synthesis, optical, and structural properties of CdSe and CdTe nanocrystals. They were formed in aqueous solutions at moderate temperatures by a wet chemical route in the presence of thiol molecules as effective stabilizing agents. The size-selective precipitation technique was applied for the post-preparative nanoparticle fractionation into a series of CdSe and CdTe nanocrystals with extremely narrow size distributions exhibiting mean cluster sizes in the range of 2 to 4 nm. The nature of stabilizing agent (mercaptoalcohols and mercaptoacids) had an important influence on the particle size and determines largely the photoluminescence properties. The nanocrystals were characterized by means of UV-vis absorption and photoluminescence spectroscopy, X-ray diffraction, and high resolution transmission electron microscopy (HRTEM).     

Solution-based II-VI core/shell nanowire heterostructures

We demonstrate the solution-phase synthesis of CdS/CdSe, CdSe/CdS, and CdSe/ZnTe core/shell nanowires (NWs). On the basis of bulk band offsets, type-I and type-II heterostructures are made, contributing to the further development of low-dimensional heteroassemblies using solution-phase chemistry. Core/shell wires are prepared by slowly introducing shell precursors into a solution of premade core NWs dispersed in a noncoordinating solvent at moderate temperatures (215-250 degrees C). Resulting heterostructures are characterized through low- and high-resolution transmission electron microscopy, selected area electron diffraction, and energy dispersive X-ray analysis. From these experiments, initial shell growth appears to occur through either Stranski-Krastanov or Volmer-Weber island growth. However, beyond a critical shell thickness, nucleation of randomly oriented nanocrystals results in a polycrystalline coat. In cases where overcoating has been achieved, corresponding elemental analyses show spatially varying compositions along the NW radial direction in agreement with expected element ratios. Electronic interactions between the core and shell were subsequently probed through optical studies involving UV-vis extinction spectroscopy, photoluminescence experiments, and transient differential absorption spectroscopy. In particular, transient differential absorption studies reveal unexpected shell-induced changes in core NW Auger kinetics at high carrier densities. Previously seen three-carrier Auger kinetics in CdS (bimolecular in CdSe) NWs were suppressed by the presence of a CdSe (CdS) shell. These observations suggest the ability to influence NW optical/electrical properties by coating them with a surrounding shell, a method which could be important for future NW optical studies as well as for NW-based applications.     

Colloidal CdSe nanocrystals synthesized in noncoordinating solvents with the addition of a secondary ligand: exceptional growth kinetics

The addition of a secondary ligand, trioctylphosphine oxide, in the synthesis of cadmium selenide nanocrystals performed in a system with oleic acid as the primary ligand and octadecene as the noncoordinating solvent gives rise to the improvement of nanocrystal size distribution. This phenomenon, which is more significant in the nucleation process than in the growth process, demonstrates that the existence of trioctylphosphine oxide allows for superior nucleation control and permits the facile and reproducible production of extremely small CdSe nanocrystals with narrow size distribution. A systematic study of the nanocrystal formation processes shows that the well-established colloidal nanocrystal growth mechanism, in which nucleation is followed by focusing of size distribution and ended with defocusing of size distribution, cannot be applied to our reactions. Instead, we observed an exceptional type of growth mechanism in which, after nucleation, clear defocusing instead of focusing follows; then slight focusing occurs.     

The Effect of CdSe and InP Quantum Dots on the Interaction of ZnO with NO<Subscript>2</Subscript> under Visible Light Irradiation

Nanocomposites based on nanocrystalline ZnO and CdSe and InP nanocrystals (quantum dots) have been synthesized by chemical precipitation and high-temperature colloidal synthesis. The microstructure parameters of the oxide matrix and the size of the CdSe and InP nanocrystals have been determined. A correlation was established between the spectral dependence of the photoconductivity of nanocomposites and the optical absorption spectra of quantum dots. The influence of CdSe and InP quantum dots on the interaction of ZnO with NO₂ under visible light irradiation has been studied. It has been shown that the synthesized nanocomposites can be used to detect NO₂ under illumination with green light without additional thermal heating.     

Nucleation and growth of CdSe nanocrystals in a binary ligand system

The competing effects of two ligands, oleic acid (OA) and bis-(2,2,4-trimethylpentyl) phosphinic acid (TMPPA), on the nucleation rate and growth of CdSe nanocrystals in octadecene are reported. It is found that TMPPA acts as a high boiling point "nonsolvent" or "nucleating agent". Addition of TMPPA leads to higher initial particle yields and smaller particle diameters. Conversely, oleic acid inhibits nucleation and results in a drastic increase in "early time ripening" (ETR), a phenomenon that causes a rapid reduction in the number of particles within the first minutes of reaction. By controlling the number of nuclei formed with TMPPA and tuning the rate of ETR with oleic acid, high yields of particles can be obtained with sizes between 3 and 7 nm. Furthermore, in the absence of OA, the preparation of very small nanocrystals with diameters approximately 2 nm is facilitated.     

Controllable Conversion of CdNCN Nanoparticles into Various Chalcogenide Nanostructures for Photo-driven Applications

Semiconductor nanocrystals of tunable shell/core configurations have great potential in photo-driven applications such as photoluminescence and photocatalysis, but few strategies realize a controllable synthesis with respect to both the size of the core and the shell with high crystallinity. Here, a new synthetic method based on cadmium cyanamide (CdNCN) nanoparticle anion exchange reactions was developed to access solid or hollow CdSe nanocrystals with tunable size and CdNCN@CdS heterostructures with modulated shell/core thickness. The gradual shift and narrow width of photoluminescence features demonstrate the high crystallinity and monodispersity of the resulting CdSe nanocrystals. In the CdNCN@CdS heterostructures, synergistic effects of the photocarrier separation is observed between the CdS shell and CdNCN core, which leads to great improvement in photocatalysis with optimized shell/core ratio.     

Water-soluble CdSe and CdSe/CdS nanocrystals: a greener synthetic route

We report a new green synthetic route of CdSe and core-shell CdSe/CdS nanoparticles (NPs) in aqueous solutions. This route is performed under water-bath temperature, using Se powder as a selenium source to prepare CdSe NPs, and H(2)S generated by the reaction of Na(2)SH(2)SO(4) as a sulfur source to synthesize core-shell CdSe/CdS NPs at 25-35 degrees C. The synthesis time of every step is only 20 min. After illumination with ambient natural light, photoluminescence (PL) intensities of CdSe NPs enhanced up to 100 times. The core-shell CdSe/CdS NPs have stronger photoactive luminescence with quantum yields over 20%. The obtained CdSe NPs exhibit a favorable narrow PL band (FWHM: 50-37 nm) with increasing molar ratio of Cd/Se from 4:1 to 10:1 at pH 9.1 in the crude solution, whereas PL band of corresponding CdSe/CdS NPs is slightly narrower. The emission maxima of nanocrystals can be tuned in a wider range from 492 to 592 nm in water by changing synthesis temperature of CdSe core than those reported previously. The resulting new route is of particular interest as it uses readily-available reagents and simple equipment to synthesize high-quality water-soluble CdSe and CdSe/CdS nanocrystals.     

Single-source precursor route for overcoating CdS and ZnS shells around CdSe core nanocrystals

We reported a facile route for overcoating CdS and ZnS shells around colloidal CdSe core nanocrystals. To synthesize such double shelled core/shell nanocrystals, first, CdSe core nanocrystals were prepared in a much “greener” and cheap route, which did not involve the use of hazardous and expensive trioctylphosphine. Then, a low-cost and labor-saving route was adopted for the CdS and ZnS shell growth with the use of thermal decomposition of commercial available air stable single-source precursors cadmium diethyldithio-carbamate and zinc diethyldithiocarbamate in a non-coordinating solvent at intermediate temperatures. Powder X-ray diffraction patterns and transmission electron microscopy images confirm the epitaxial growth of the shell in the core/shell nanocrystals. The photoluminescence quantum yield of the resulting CdSe/CdS/ZnS core/shell nanocrystals can be as high as 90% in organic media and up to 60% after phase transfer into aqueous media. By varying the size of CdSe cores, the emission wavelength of the obtained core/shell nanostructures can span from 554 to 636 nm.     

A numerical study on the coalescence of emulsion droplets in a constricted capillary tube

Using a new computational model, we have studied the dynamics and coalescence of a pair of two-dimensional droplets in pressure-driven flow through a constricted capillary tube, which is a prototype problem for the analysis of the interaction of emulsion droplets in porous media. We present simulations that quantify the effects of various system parameters on the droplet stability. These include the capillary number, the interfacial tension, the suspended-to-suspending-phase viscosity ratio, the valence and concentration of added electrolytes, the droplet-to-pore-size ratio, the pore-body-to-throat-size ratio, and the type of pore geometry. Our simulations show that the capillary number Ca plays an important role in determining whether the drops coalesce. At low Ca, drops deform only slightly and coalescence occurs at the entrance of the pore throat, whereas significant deformation enables the drops move through the pore without coalescence at high Ca. Coalescence is favored at intermediate values of the viscosity ratio. The destabilizing effect of added electrolytes is found to be insignificant for 10-mum drops, but significant for micron-size drops. Among the geometric-related parameters, the drop-to-pore-size ratio is the most significant.     

Control of photoluminescence properties of CdSe nanocrystals in growth

The photoluminescence (PL) quantum yield (QY) of CdSe nanocrystals during their growth under a given set of initial conditions increases monotonically to a certain maximum value and then decreases gradually. Such a maximum is denoted as a PL "bright point", which does not always overlap with the minimum point of the PL peak width for the same reaction. The experimental results suggest that the existence of the PL bright point is a general phenomenon during the growth of semiconductor nanocrystals and likely is a signature of an optimal surface structure/reconstruction of the nanocrystals grown under a given set of initial conditions. The position of the bright point, the highest PL QY, the types of the bright points (sharp or flat), the sharpness of the PL peak, etc., were all strongly dependent on the initial Cd:Se ratio of the precursors in the solution. A large excess of the selenium precursor, with 5-10 times more selenium precursor than the amount of the cadmium precursor, was found necessary to achieve a high PL QY value and a narrow emission profile. The existence of the PL bright point and the sensitive temporal variation of the PL QY during the growth of semiconductor nanocrystals can explain the unpredictable nature and poor reproducibility of the PL properties of the as-prepared semiconductor nanocrystals observed previously. Furthermore, the knowledge gained in this study enabled us to reproducibly synthesize highly luminescent CdSe nanocrystals through a relatively simple and safe synthetic scheme. In a traditionally weak emission window for CdSe nanocrystals, the orange-red optical window, the PL QY of the as-prepared CdSe nanocrystals reached as high as 85% at room temperature, and the full width at half-maximum of the corresponding PL peak was as narrow as 23 nm, about 65-80 meV depending on the emitting position. The PL properties of the as-prepared CdSe nanocrystals are stable upon aging for at least several months. These as-prepared nanocrystals represent a series of best emitters that are highly efficient, highly pure in emission color, stable, and continuously tunable by simply varying the size of the nanocrystals.     

A new route to zinc-blende CdSe nanocrystals: mechanism and synthesis

We report the possible mechanism of forming of CdSe nanocrystals in the high boiling point solvents with long alkane chains and a novel Non-TOP-Based route to zinc-blende CdSe nanocrystals. A new mechanism shows that there exits a redox reaction in the long alkane chain solvents: Se is reduced to H2Se gas; at the same time, the long alkane chains are oxidated to alkene chains; then, the Cd complex reacts with H2Se to form CdSe nanocrystals. Possible chemical reaction equations involved in the process of forming the CdSe nanocrystals have been discussed. The alkene chain and H2Se were detected respectively by a series of experiments to support the new mechanism. Under the guidance of this mechanism, we have developed a much cheaper and greener Non-TOP-Based route for the synthesis of a size series of high-quality zinc-blende (cubic) CdSe nanocrystals. Low-cost, green, and environmentally friendlier reagents are used, without use of expensive solvents such as trioctylphosphine (TOP) or tributylphosphine (TBP). The new route enables us to achieve high-quality CdSe nanocrystals with sharp ultraviolet and visible (UV-vis) absorption peaks, controllable size (2.0-5.0 nm), bright photoluminescence (PL), narrow PL full width of half-maximum (fwhm) (29-48 nm), and high PL quantum yield (up to 60%) without any size sorting.     

Effect of confinement on droplet breakup in sheared emulsions

The breakup of Newtonian droplets in a Newtonian matrix during shear flow is investigated in a counterrotating parallel plate device. For bulk conditions, the critical capillary number for breakup is known to be only determined by the viscosity ratio. Here, we show that the critical capillary number is also affected by the degree of confinement: for low viscosity ratios, confinement suppresses breakup, whereas for high viscosity ratios, confinement promotes breakup. This way, above a critical value for the degree of confinement, even droplets with a viscosity ratio larger than 4, which are unbreakable by shear in a bulk situation, can be broken in a simple shear flow field.