魔方状微纳结构BaTiO3的制备及其压电催化性能

在简单溶剂热条件下,通过控制钡、钛物质的量之比制备了魔方状微纳结构BaTiO₃粉体,并以5 mg·L^-1罗丹明B (RhB)溶液为降解对象测试其压电催化性能。采用扫描电子显微镜、X射线衍射、傅里叶变换红外光谱对所制备粉体的物化性质进行详细表征,并测试其压电、光催化活性及循环稳定性。结果表明,钡、钛物质的量之比为1∶1时,合成的粉体为由立方体组装而成的魔方状四方相结构的BaTiO₃。在40 kHz、360 W的超声条件下,180 min内的降解率达90%,5次循环后的降解率为79.7%,变化率为11.4%,优于其光催化性能,具备优异的压电催化活性及循环稳定性。     

低温合成四方相BaTiO3及其压电催化性能

基于淀粉糊化机制低温合成了四方相BaTiO₃粉体。采用扫描电子显微镜、透射电子显微镜、X射线衍射、傅里叶变换红外光谱、紫外可见吸收光谱、X射线光电子能谱对合成粉体的形貌、物相进行表征;在超声条件下,以系列典型染料为降解对象测试BaTiO₃压电催化性能。结果显示,煅烧温度为600℃时即可获得四方相BaTiO₃粉体,且随着温度的提升,结晶度逐渐增加;当煅烧温度为700℃时,合成的BaTiO₃粉体尺寸分布均匀,分散度良好,呈现类立方体状;在超声驱动下,BaTiO₃降解罗丹明B、刚果红、甲基橙染料时均展现出良好的效果,反应速率常数分别为1.090×10^-2、1.113×10^-2、1.084×10^-2 min^-1,并以降解刚果红为对象揭示其压电催化的机理,即空穴和超氧自由基是降解过程中的主要反应物质。     

熔盐法包覆BaTiO3及其电性能

通过熔盐法,将MgTiO3薄膜均匀地包覆在钛酸钡颗粒表面,。形成芯壳结构,包覆机理是在MgCl2的熔盐状态（800度）下,Mg^2 取代BaTiO3中的Ba2 离子,表面生成MgTiO3薄膜,薄膜厚度约20nm,采用TEM,XRD验证了MgTiO3的包覆,包覆粉末经烧成瓷后,具有良好的高频性能,在1MHz-800MHz的频率范围内,介电常数恒定为130。     

BaTiO3和SrTiO3薄膜生长初期化学分子反应机理

本文采用B3LYP密度泛函方法,研究了BaO、SrO与TiO2形成BaTiO3、SrTiO3及TiO2二聚形成Ti2O4的微观反应机理,获得了相应的中间体、过渡态及反应活化能。采用自然键轨道NBO方法分析了反应过程中各中间体和过渡态的成键情况、轨道间的相互作用以及原子的电荷。计算结果表明,形成BaTiO3、SrTiO3和Ti2O4反应活化能分别为16.3、17.3和9.6 kJ/mol,TiO2形成二聚体活化能相对较小,从理论上解释了实验过程中观测到TiO2二聚体;但SrO、BaO和TiO2形成BaTiO3、SrTiO3的反应过程中,形成最初的稳定中间体时分别放热484.7和534.7 kJ/mol,且活化能较低,轨道间相互作用较强,静电引力作用显著,有利于SrTiO3和Ba-TiO3薄膜生长初期以TiO2为中心,结合BaO和SrO成核生长,从而有利于单元胞的进一步形成。     

表面改性纳米BaTiO3杂化聚酰亚胺薄膜的合成及其热性能

以3,3’,4,4’-联苯四酸二酐和4,4’-二氨基二苯醚为原料,通过原位聚合和流延成膜法制备了不同纳米BaTiO3含量的聚酰亚胺(PI)/BaTiO3杂化膜。采用不同的硅烷偶联剂对纳米BaTiO3进行表面改性,发现γ-巯丙基三乙氧基硅烷(KH590)的改性效果较好。大部分杂化膜在质量损失5%的温度都较纯膜有不同程度的升高,最多升高了18℃,说明PI/BaTiO3杂化膜较纯膜具有更好的耐热性能,且热分解温度均高于520℃。     

B-Co3O4/C复合纳米材料的制备及其电催化析氧性能

本文以雪莲果为碳源,采用热解法制备碳材料(C),以硝酸钴、四硼酸钠和碳材料为原料,通过热解法合成硼掺杂四氧化三钴/碳(B-Co₃O₄/C)复合纳米材料。运用XRD、FTIR、SEM、XPS等手段对其结构、形貌和组成进行表征。利用线性扫描(LSV)和Tafel曲线等电化学测试方法研究了B-Co₃O₄/C复合纳米材料的电催化析氧反应(OER)性能。结果表明,该材料具有较好的电催化OER活性。在1.0mol/L的KOH电解液和10mA·cm^-2的电流密度下,B-Co₃O₄/C复合纳米材料的过电位为293mV,Tafel斜率为45.0mV·dec^-1。在10mA·cm^-2电流密度下连续测试10h, B-Co₃O₄/C的电位变化不大,通过法拉第效率测试该催化剂的产氧效率为94%,说明硼原子的掺入改变了B-Co₃O₄...     

多孔微纳结构富锂正极材料0.6Li2MnO3·0.4LiNi0.5Mn0.5O2的制备及其电化学性能

采用碳酸盐共沉淀与燃烧法相结合的方法制备得到了多孔微纳球形结构的富锂正极材料0.6Li₂MnO₃·0.4LiNi_0.5Mn_0.5O₂。借助X射线衍射（XRD）分析、X射线光电子能谱（XPS）、扫描电镜（SEM）、透射电镜（TEM）、N₂吸附-脱附和恒电流充放电测试研究了其晶体结构、微观形貌和电化学性能。结果表明该方法制备出的材料是由一次颗粒径约300 nm的小颗粒组成的多孔微纳球形结构,比表面积为13 m²·g^-1,具有完善的α-NaFeO₂层状结构（空间群为R3m）。电化学性能测试结果证实该材料具有优异的高容量、高循环稳定性和高倍率性能。在2.0~4.8 V,电流密度为0.1C、0.2C、0.5C、1C、3C、5C和10C时的放电比容量分别为：266、254、235、205、186、149和107 mAh·g^-1;在0.5C下循环100次后,放电比容量仍为217 mAh·g^-1（容量保持率为94%）。     

微纳结构柔性压力传感器的制备及应用

柔性压力传感器是一种能够感知或监测外界压力变化的柔性电子器件,具备灵敏度高、形变灵活、制备工艺简单等特点,在可穿戴式电子产品、健康医疗、软体机器人、人机交互等新兴领域具有广泛而重要的应用。灵敏度、检测极限、响应时间与循环工作稳定性是柔性压力传感的核心性能指标,微纳结构的引入对提高柔性压力传感器综合性能具有重要作用。本文根据微纳结构的主要类型介绍了基于微纳结构的柔性压力传感器的最新研究进展,包括各种不同形貌微纳结构对柔性压力传感器性能的影响及其在柔性压力传感器中的应用,并对柔性压力传感器未来的发展提出展望。     

B2O3-Bi2O3-ZnO-Al2O3玻璃助烧剂对BaTiO3陶瓷烧结条件、晶体结构和介电性能的影响

通过调节B₂O₃-Bi₂O₃-ZnO-Al₂O₃(BBZA)玻璃的添加量研究其对钛酸钡(BaTiO₃)陶瓷烧结条件、晶体结构和介电性能的影响。结果表明：添加适量的BBZA玻璃能够有效地将BaTiO₃陶瓷烧结温度由1 350℃降至950℃,并使其致密化。同时,添加BBZA玻璃后,BaTiO₃的晶体结构随着烧结温度的升高而发生转变(立方相→四方相)。另外,BBZA玻璃的引入使BaTiO₃陶瓷的居里峰得到了有效的抑制和拓宽。陶瓷微观形貌显示,玻璃相均匀分布在BaTiO₃晶粒表面。优化的BaTiO₃陶瓷制备条件如下：BBZA添加量(质量分数)为2.0%,烧结温度为950℃。在该条件下制备的BaTiO₃陶瓷介电常数达到1 364,介电损耗低至1.2%。     

碳微球模板制备LaMnO3及其电化学性能研究

以葡萄糖为碳源采用水热法制备出碳微球,再将其作为模板剂,柠檬酸作为络合剂,去离子水和乙醇作为溶剂,经混合搅拌、沉淀和去除模板剂等步骤,由La(NO₃)₃·6H₂O和Mn(NO₃)₂制备LaMnO₃。采用粉末X射线衍射、场发射扫描电镜、N₂吸附-脱附等对LaMnO₃进行表征分析,并对其电化学性能进行了测试。结果表明,碳微球模板可制备出层状多孔结构的LaMnO₃,其具有良好的氧还原反应(ORR)和析氧反应(OER)催化活性,比表面积为26m²/g,将其制备成铝-空气电池空气电极催化剂,在电流密度20mA·cm^-2时放电电压可达1.476V,高于共沉淀法制备的LaMnO₃的放电电压。     

稀土改性BaTiO3粉体的制备及其导电性分析

采用溶胶-凝胶法制备了纯BaTiO3粉体,并以La、Pr、Nd、Sm、Gd和Er等稀土元素通过液相掺杂、气相掺杂和液-气共掺3种不同的方式对其进行改性,以提高BaTiO3粉体的导电性.实验结果表明:各种稀土均可降低BaTiO3粉体的电阻率,效果最好的是Sm.不同掺杂方式中液-气共掺的效果最好,通过液相掺杂、气相掺杂和液-气共掺,BaTiO2粉体的电阻率由4.30×109Ω·m分别降至2.38×105,4.34×104和35.4 Ω·m.XRD、SEM、FTIR分析表明.液相掺杂时进入BaTiO3粉体的稀土元素主要集中在晶界处,而气相掺杂后稀土元素主要进入晶格内部,可能取代了Ti4+在晶格中的位置.半径较小的稀土元素更容易迁移而偏离钛氧八面体的中心位置,由此导致稀土掺杂后BaTiO3粉体的电阻率显著降低.     

BaPbO3与BaTiO3多晶态陶瓷缺陷结构对比

BaPbO，是具有类金属导电特性的钙钛矿结构导电陶瓷，其晶体结构由Ba2＋和O^2-离子紧密堆积形成，pb^4＋离子占据由O^2-离子形成的八面体空隙。BaTiO3同为钙钛矿结构的陶瓷材料，由Ba^2＋和O^2-离子紧密堆积形成，Ti^4＋离子占据由O^2-离子形成的八面体空隙。BaPbO3和BaTiO3的A位离子相同,B位离子都为可变价离子。     

Preparation and electrorheological characteristic of Y-doped BaTiO3 suspension under dc electric field

The electrorheological (ER) effects of BaTiO₃ or other perovskite materials with high dielectric constant are presumed to be large. However, their weak ER activity is very puzzling. In this study, we choose cubic BaTiO₃ and first achieve its ER enhancement under dc electric field by modifying its intrinsic structure with doping rare earth Y ions, which are synthesized by means of sol-gel technique. DSC-TG, FT-IR, XRD, ICP and XPS techniques are used to characterize thermal, structure and component change of materials. It is demonstrated that Y³⁺ substitutes for Ba²⁺, which causes lattice-distorting defects. Rheological experiments show that Y-doped BaTiO₃ suspension has notable ER effect and clear fibrillation structure under dc electric field, while the pure cubic BaTiO₃ suspension suffers from electrophoretic effects and its ER effect is very weak. The ER effect of typical Y-doped BaTiO₃ ER suspension is ten times that of pure BaTiO₃ ER suspension. Based on the electrical measurements, the enhancement of ER activity of BaTiO₃ may be attributed to the increase of conductivity due to Y-doping. The enhancement in ER activity of cubic BaTiO₃ under dc electric field by doping rare earth Y ions is helpful to further understand the perovskite-based ER materials with high dielectric constant but low ER activity.     

溶胶凝胶法制备Nd2O3改性钛酸钡陶瓷的研究

The technological condition for the preparation of BaTiO₃ ceramics doped with Nd₂O₃ by Sol-Gel was deter-mined through orthogonal experiment. When n_Ba(Ac)2∶n_Ti(OC4H9)4∶n_Nd2O3∶n_{CH3(CH2)2CH2OH}∶n_H2O=1.00∶1.00∶0.003∶7.30∶37.04, pH=3.5,T=25℃,the light-yellow-transparent-stable solution and thorough transparent gel was generat-ed, the transforming time of solution to gel was 25h. The crystal structure and particle size of BaTiO₃ ceramics doped with Nd₂O₃ were studied by SEM and X-ray respectively, the type of the crystal was tetragonal, the particle size was about 24.7nm. The dielectric constant (ε) and dielectric loss (tanδ) of BaTiO₃ ceramics doped with Nd₂O₃ were determined between 10⁴～10⁶Hz, and the results showed that the dielectric constant was increased obviously, the dielectric loss was decreased clear and the resistivity (ρ_V) was also decreased noticeably.     

Nd2O3添加量对BaTiO3陶瓷介电性能的影响

BaTiO₃ ceramics doped with Nd₂O₃(the additive content was respectively 0.001,0.002,0.003,0.005,0.01,0.03mol)were prepared by Sol-Gel method. Effects of Nd₂O₃ contents on the dielectric constant (ε), the dielectric loss (tanδ) ,the Curie-temperature (T_C) and the resistivity (ρ) of BaTiO₃ ceramic were studied. When Nd₂O₃ content was 0.001mol and 0.002mol, the dielectric constant was increased obviously, but the dielectric loss was also increased. When Nd₂O₃ content was 0.003mol, the dielectric constant was increased, and the dielectric loss was decreased, which was suitable for application in condenser. The resistivity was decreased obviously with the increasing of Nd₂O₃ contents, the resistivity was the smallest when Nd₂O₃ content was 0.001mol. The Curie-temperature was also decreased with the increasing of Nd₂O₃ contents.     

Grain size modulation on BaTiO3 nanoparticles synthesized at room temperature

A new method is developed to synthesize massive BaTiO₃ nanoparticles directly at room temperature. With this method, the synthesis efficiency is improved and mass preparation can be realized. Also, the grain size of the as-prepared nanoparticles can be modulated from several nanometers to 40 nm through proper selection of the content of water and the alkanol chain length of the dispersant. It was found that smaller water content and a larger alkanol chain length of the dispersant will lead to a finer grain size. The mechanisms of the grain size modulation of BaTiO₃ nanoparticles are also discussed.