The effect of polyvinyl alcohol (PVA) on the optical,electrical and solid state properties of copper zinc tin sulfide (CZTS) deposited by sensitive spray pyrolysis (SSP)

Recently, the use of CZTS as the basis for other generation of low cost thin films solar cells has stimulated further researches. Its excellent p-type absorber nature, relatively high absorption coefficient and ideal energy band-gap of 1.5eV motivated these efforts. Additionally, CZTS consist of earth-abundant, cheap and non-toxic elements with very low manufacturing cost. Initially, copper indium gallium selenide (CIGS) solar cell device emerged but suffered limitations in further development because of rare indium and gallium in the device structure therefore, CZTS is recently preferred as an alternative to CIGS commercial solar cell absorber layer. In this work, solution mixture of CZTS and PVA was deposited on a substrate at temperature of 150 °C. Sensitive spray pyrolysis was used to grow the thin films where calculated amount of the precursor mixture was allowed to fall and be deposited on a heated substrate to form CZTS/PVA thin films. Subsequently, the thin film samples were annealed at a temperature of 200^oCfor 1 h to achieving pure crystalline thin film formation. SEM, XRD analysis, Optical, Solid State properties and Raman analysis were studied. The XRD analysis showed that the thin films fell into the pure kesterite structure of CZTS. Results show that produced thin films exhibited higher absorption coefficient and optical conductivity than pure CZTS, 10⁶ m^?1 and 10¹⁴(S^?1) against 10⁴cm^?1 and 10¹²(S^?1) respectively. The band-gap is between 1.53eV and 1.73eV. Using a PVA concentration of 0.05 M yielded highest absorbance and optical conductivity with lowest real dielectric constant and transmittance. These improved optical, electrical and solid state properties suitably qualify these thin films as absorber layer material for solar cell applications.     

Improvement of electrical and material properties of epoxy resin/ aluminum nitride nanocomposites for packaging materials

This paper presents the influence of Aluminum Nitride (AlN) nanoparticles on the electrical and material properties of epoxy resin (EP). The EP/AlN nanocomposites with different concentrations of nano-AlN fillers are prepared. The dispersion of the nano-AlN particles in the composites is analyzed by a field emission scanning electron microscope (FESEM). The electrical properties are investigated by the space charge and DC conductivity measurements, whereas the material properties are studied by Fourier transform infrared (FT-IR), thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC), respectively. The results show that the homo-charge accumulation appears near both electrodes during the polarization, but there are limited negative charges left near both electrodes in the depolarization for the pure EP sample. There is no space charge accumulation in the 1 wt% and 2 wt% EP/AlN nanocomposites. The electric field distortion of the pure EP sample is 20%. Moreover, the electric field distortion initially decreases with the increase of the nano-AlN content, but it increases for the 2 wt% nano-AlN sample. Temperature has a dominant influence on the DC conductivity of the EP/AlN nanocomposites comparing to the pure EP. However, the DC conductivity of the nanocomposites becomes stable at high temperatures. It is also found that the weight loss of the samples decreases with the addition of the nano-AlN and the 1 wt% nano-AlN sample has the highest glass transition temperature. It is elucidated that the high apparent mobility and activation energy facilitate the space charge transport and suppressing the space charge accumulation. Furthermore, the nano-AlN filler can increase the trap level and trap energy density of the deep traps in the sample. The dielectric loss of the EP at high frequency is reduced with the content of 1 wt% nano-AlN. Furthermore, the addition of the nano-AlN can improve the thermal stability of the EP. The 1 wt% nano-AlN sample has the superior electrical insulation and material performance amongst the tested materials.     

Investigation of the electrical properties of XLPE/SiC nanocomposites

The interface between nanoparticles and the polymer matrix, which dominates the electrical properties of nanocomposites, can effectively improve the DC breakdown and suppress space charge accumulation in nanocomposites. To research the interface characteristics, XLPE/SiC nanocomposites with concentrations of 1 wt%, 3 wt% and 5 wt% were prepared. The DC breakdown, dielectric properties and space charge behavior were examined using pulsed electro-acoustic (PEA) equipment and a dielectric analyzer. The test results show that the nanocomposites with concentrations of 1 wt% and 3 wt% have higher DC breakdown field strength than neat XLPE. In contrast, there is a lower DC breakdown strength at a concentration of 5 wt%, possibly due to the agglomeration of nanoparticles. Nanoparticle doping increases the real and imaginary permittivities over those of neat XLPE. Furthermore, with increasing concentration, a larger increase in the permittivity amplitude was observed. Based on the space charge behavior, all nanocomposites could suppress space charge accumulation, but the nanocomposite with a concentration of 1 wt% exhibited the best effect. Meanwhile, heterocharge accumulation near electrodes was observed in neat XLPE and the nanocomposite with a concentration of 5 wt%. In contrast, homocharge accumulation near electrodes was observed in the nanocomposite with a concentration of 3 wt%. This phenomenon may be due to different amounts of shallow traps in nanocomposites with different concentrations, which might lead to differing electron or hole mobility.     

Preparation and properties of polymer/zinc oxide nanocomposites using functionalized zinc oxide quantum dots

Poly(methyl methacrylate) (PMMA)/zinc oxide (ZnO) or carbazole polymer (PCEM)/ZnO nanocomposites, which are composed of high molecular weight PMMA or PCEM with narrow molecular weight distributions and ZnO nanoparticles, were successfully prepared by atom transfer radical polymerization (ATRP) initiated by 2-bromo-2-methylpropionyl (BMP) group (ZnBM) introduced onto the ZnO nanoparticle surfaces. Introduction of the BMP group onto the ZnO surfaces was achieved by esterification of OH group of the ZnO surfaces. The chemically attached OH group-having ZnO nanoparticles (ZnHM) were fabricated by sol-gel reaction from zinc acetate dihydrate, followed by treatment of the ZnO nanoparticles with 2-hydroxypropionic acid (HPA). The ZnHM nanoparticles showed one UV absorption and two emission bands: UV emission peak and broad visible emission band, while the ZnBM exhibited broad UV absorption and no emission spectra. The PMMA/ZnO nanocomposites displayed UV absorption and photoluminescent (PL) band with blue emission on the basis of the ZnHM nanoparticles, where the ZnO nanoparticles dispersed homogeneously in the PMMA matrix. The PCEM/ZnO nanocomposites depicted UV emission peak due to the carbazole unit in the UV range, but no visible emission. Thermal properties of the PMMA/ZnO nanocomposites were improved by dispersion of the ZnO nanoparticles into the PMMA, but the PCEM/ZnO nanocomposites showed no improvement of the thermal properties.     

Thermal,mechanical and water barrier properties of graphene oxide/polyvinyl alcohol/polyol composite films

The novel polymer composite of polyvinyl alcohol (PVA), polyol(PO) and graphene oxide (GO) was used to prepare the PVA/PO and GO/PVA/PO with different weight percents of GO (0.5 and 1% denoted as (0.5 wt%)GO/PVA/PO and (1 wt%)GO/PVA/PO, respectively) through solution casting blend technique. The structure–properties of all used films were confirmed by scanning electron microscope (SEM), Transmission Electron Microscope (TEM), X-ray powder diffraction (XRD), thermogravimetric analysis (TGA) and mechanical properties. The SEM results exhibited the uniform and homogeneous dispersion of GO in the PVA/PO blend matrix. The TEM and XRD analysis confirmed the structure and exfoliation of GO nanosheets, respectively. Thermal stability suggested that (0.5 wt%)GO/PVA/PO and (1 wt%) GO/PVA/PO films are more stable than PVA/PO. The tensile strength of (0.5 wt%)GO/PVA/PO and (1 wt%)GO/PVA/PO films reached 270.5% and 1349.6%, respectively, which are higher than that of the PVA/PO film. The decrease in the water absorption (WA) of GO/PVA/PO was found from 110.5 to 38.4%. The physico-mechanical properties of used films suggested that the prepared GO/PVA/PO blend composite films can be applied in food packaging areas.     

Polyimide nanocomposites based on functionalized graphene sheets: Morphologies,thermal properties,and electrical and thermal conductivities

Polyimide (PI) films were prepared by reacting 4,4′-(4,4′-isopropylidene-diphenoxy)-bis(phthalic anhydride) and 1,3-bis(4-aminophenoxy)benzene. The 4-phenylbutylamine-functionalized graphene sheets (PBA-GSs) used for the preparation of the PI nanocomposite films were prepared by mixing a dispersion of graphite oxide with a solution of the ammonium salt of 4-phenylbutylamine (PBA). PI nanocomposite films containing different amounts of PBA-GS (0–10 wt%) were compared in terms of their morphologies, thermal properties, and electrical and thermal conductivities. Only a small amount of PBA-GS was required to improve the thermal properties and thermal conductivities of the PI; the maximum enhancements in these parameters were observed at 1 and 3 wt% PBA-GS, respectively. In contrast, the electrical conductivity of the PI hybrid films continued to increase with increasing PBA-GS content from 1 to 10 wt%.     

Enhancement of tensile,electrical and thermal properties of epoxy nanocomposites through chemical hybridization of polypyrrole and graphene oxide

This paper presents the properties of epoxy nanocomposites, prepared using a synthesized hybrid Polypyrrole-Graphene Oxide (PPy-GO) filler, via in-situ chemical polymerization, at various filler loadings (i.e., 0.5–2 w. t %). The microstructures and properties of the PPy-GO hybrids and epoxy nanocomposites were studied via Fourier transform infrared (FTIR), X-ray diffraction (XRD), Scanning Electron Microscopy (SEM), Transmission Electron Microscopy (TEM), mechanical (Tensile Properties), electrical, Dynamic mechanical thermal analysis (DMTA) and thermogravimetric analyses (TGA). Morphological study demonstrated that varying the nanofiller nature (PPy-GOs, PPy or GO) lead to different states of dispersion. Mechanical, electrical and thermal analysis demonstrated that the hybrid concentration and its architecture (PPy:GO ratio) are interesting factors significantly affected the properties of the epoxy based nanocomposites. On the other hand, the mechanical performance of the cured nanocomposites outperformed the PPy-GO, with enhancements of 78% and 51% of Young's modulus and strength, respectively. Here it has been established that the embedding of PPy-GO hybrids into pristine epoxy endows optimum dispersion of PPy and GO as well as better interfacial adhesion between the fillers and matrix, which results in a significant improvement in load transfer effectiveness. Electrical conductivity measurements showed that conductivity of epoxy filled nanocomposites increased up 10⁻⁴ S/cm for Epoxy/PPy-GO nanocomposites. DMTA test indicated that incorporation of PPy-GO resulted in a significantly increase in Tg of the resultant nanocomposites, which is attributed to the highly exfoliation structure and the stronger interfacial interaction. The PPy-GO particles enhanced electrical, thermal and mechanical properties of nanocomposites, confirming the synergistic effect of PPy-GO as multifunctional filler.     

Effects of α-zirconium phosphate aspect ratio on the properties of polyvinyl alcohol nanocomposites

To study the effect of the aspect ratio (ratio of platelet length to thickness) of α-zirconium phosphate (α-ZrP) on the mechanical and thermal properties of polymer nanocomposites, polyvinyl alcohol (PVA)/α-zirconium phosphate (α-ZrP) nanocomposites with three distinctive aspect ratios at ca. 300, 590 and 1300 were prepared and characterized. Wide-angle X-ray diffraction (XRD), scanning electron microscopy (SEM), thermal gravimetric analysis (TGA), differential scanning calorimetry (DSC), dynamic mechanical (DMA) and tensile testing were utilized to characterise the film properties. As expected, it was found that the storage modulus, tensile strength (σ_b), elongation at break (_b) and decomposition temperature increased as the α-ZrP aspect ratio increased from 300 to 590. However, when the aspect ratio reached 1300, the enormously enlarged specific surface area of α-ZrP resulted in strong aggregation of the nanolayers which resulted in severe deterioration of the film properties.     

Morphology and physical properties of poly(ethylene oxide) loaded graphene nanocomposites prepared by two different techniques

Organic–inorganic hybrids are artificially created structures presenting novel properties not exhibited by either of the component materials alone. In this contribution one addresses processing, morphology and properties of polymer nanocomposites reinforced graphene. First, synthesis routes to graphite oxide (GO) and foliated graphene sheets (FGS) are illustrated. Physical characterization of these graphene sheets were conducted using atomic force microscopy and X-ray diffraction techniques. Processing, structure and properties of graphene/poly(ethylene oxide) (PEO) nanocomposites are discussed. FGS was dispersed into PEO via two different composite manufacturing techniques: melt compounding and solvent mixing. Morphology of dispersed graphene and properties from different blending routes are compared. TEM showed that graphene distributed parallel to the composite surface using solvent method, while distributed randomly in melt blended method. Optical measurements indicated that the transparency of PEO/graphene prepared by solvent method is higher than that of melt blended method in the visible region. Electrical conductivity measurements are employed to evaluate threshold concentration for rigidity and connectivity percolation. The percolation concentration of the composites prepared by solvent method is less than those of melt blended method. The mechanical performance of the composites prepared by solvent method is higher than melt blended. Halpin–Tsai model has been used to confirm the distribution of the graphene into PEO by the two different processing techniques.     

Photosensitive polyimides for applications in electrical and optical interconnection technology

The application of photosensitive polyimides in electrical and optical interconnection technology is discussed. Critical properties of two photosensitive polyimide formulations with significantly different structural chemistries have been compared. Polyamic ester based formulations such as Selectilux® HTR3 show significant distortions in the photopatterned features upon high-temperature baking, which can be ascribed to anisotropic shrinkage. A BTDA-alkylated diamine based preimidized formulation (Probimide®), on the other hand, shows a more uniform shrinkage of the photopatterned features. HTR3 films interacts strongly with metals such as copper, which adversely affect the photopatternability of these materials. Planarization behavior in multiple layer structures has also been investigated. We explored the viability of these materials for applications in optical interconnection. Probimide® materials exhibit low scattering losses and appear to be promising candidates for the development of a MCM-compatible optical interconnection technology. We also describe here a novel technique for optical recording of refractive index patterns in Probimide® films.     

Evaluation of the structural,optical and electrical properties of AZO thin films prepared by chemical bath deposition for optoelectronics

Aluminum doped zinc oxide (AZO) thin films for electrode applications were deposited on glass substrates using chemical bath deposition (CBD) method. The influence of deposition time on the structural, morphological, and opto-electrical properties of AZO films were investigated. Structural studies confirmed that all the deposited films were hexagonal wurtzite structure with polycrystalline nature and exhibited (002) preferential orientation. There is no other impurity phases were detected for different deposition time. Surface morphological images shows the spherically shaped grains are uniformly arranged on to the entire film surface. The EDS spectrum confirms the presence of Zn, O and Al elements in deposited AZO film. The observed optical transmittance is high (87%) in the visible region, and the calculated band gap value is 3.27 eV. In this study, the transmittance value is decreased with increasing deposition time. The room temperature PL spectrum exposed that AZO thin film deposited at (60 min) has good optical quality with less defect density. The minimum electrical resistivity and maximum carrier concentration values were observed as 8.53 × 10⁻³(Ω cm) and 3.53 × 10¹⁸ cm⁻³ for 60 min deposited film, respectively. The obtained figure of merit (ϕ) value 3.05 × 10⁻³(Ω/sq)^{- 1} is suggested for an optoelectronic device.     

Preparation of quaternarized N-halamine-grafted graphene oxide nanocomposites and synergetic antibacterial properties

At present, frequent outbreaks of bacteria and viruses have seriously affected people's normal lives. Therefore, the study of broad-spectrum antibacterial nanocomposites is very promising. However, most antibacterial materials have some disadvantages, such as single bactericidal mechanisms and unrepeatable use. Based on the current situation, a kind of nanocomposite with three structures of graphene oxide (GO), quaternary ammonium salt (QAs) and N-halamine was prepared, which showed synergistic effect to improve antibacterial activity and combined with a variety of sterilization mechanisms. Meanwhile, GO can provide richer ways of sterilization and high specific surface area, which is conducive to the grafting of quaternarized N-halamine. The advantages of physical sterilization of GO, charge adsorption of QAs, reuse of N-halamine and efficient sterilization are fully utilized. The results showed that the quaternarized N-halamine-grafted GO was obtained successfully. GO grafted with quaternarized N-halamine polymer showed strong speedy bactericidal activity against Escherichia coli (E. coli) and Staphylococcus aureus (S. aureus) (99%). It had good storage and regeneration properties.     

Influence of organo-clay on electrical and mechanical properties of PP/MWCNT/OC nanocomposites

The electrical, thermal and mechanical properties of nanocomposites, based on polypropylene (PP) filled by multi-walled carbon nanotubes (MWCNTs) and organo-clay (OC), were studied with the purpose of finding out the effect of OC on the microstructure of MWCNTs dispersion and PP/MWCNT/OC composites. It was found that addition of organo-clay nanoparticles improved nanotube dispersion and enhanced electrical properties of PP/MWCNT nanocomposites. Addition of organo-clay (MWCNT/OC ratio was 1/1) reduced the percolation threshold of PP/MWCNT nanocomposites from ?_c = 0.95 vol.% to ?_c = 0.68 vol.% of carbon nanotubes, while the level of conductivity became 2–4 orders of magnitude higher. The DSC and DMA analyses have shown that the influence of organo-clay on the thermal and mechanical properties of material was not significant in composites with both fillers as compared to PP/OC. Such an effect can be caused by stronger interaction of OC with carbon nanotubes than with polymer matrix.     

Investigation of structural,optical and photoluminescence properties of non-essential amino acid capped zinc sulfide nanoparticles for optoelectronic applications

The objective of the study is to synthesize Zinc Sulphide nanoparticles (ZnS) with different amino acid capping agents in aqueous solution by a simple and cost effective facile chemical co precipitation method and analyze their optoelectronic features. Bio compatibility with less toxic amino acids such as l-Glutamic acid, l-Alanine and l-Asparagine were used as capping agents. These amino acids are from Non-essential amino acid group and its capping behavior suitable for semiconducting nanoparticles like ZnS. The role of non essential amino acids were to stabilize the nanoparticle against agglomeration and also to provide chemical passivation that leads to a significant influence on the improved structural, optical and photoluminescence properties of ZnS nanoparticles. The detailed structural analysis of Zinc Sulphide nano particles revealed by X-ray diffraction method (XRD). From this analysis observed the formation of Cubic ZnS nanoparticles with an average crystallite size in the range of 2.08–2.22 nm.The morphology of the nano particles studied by Field emission scanning electron microscope (FESEM). Particle size examined by Dynamic Light scattering studies (DLS) and which revealed that particle size ranges are below 50 nm. The functional groups of nanoparticles were identified by Fourier transform Infrared spectroscopy (FT-IR) studies. Photoluminescence studies attributed that the considerable emission bands. The UV–Vis analysis disclosed the optical band gap range from 3.77 eV to 3.95 eV.     

Novel Conductive PANI/Hydrophilic Thiacalix[4]areneNanocomposites: Synthesis,Characterization andInvestigation of Properties简

Nanocomposites of polyaniline(PANI) and the macrocycle thiacalix[4]arene tetra sulfonate(TCAS) were successfully synthesized in feed ratios of 1:0.25, 1:0.50 and 1:0.75 by three prevail synthetic methods, i.e. in situ polymerization, emulsion polymerization and solution casting technique. The structures of the nanocomposites were confirmed by FTIR, UV-Vis, XRD, SEM, and TEM techniques. The conductivity was measured by a four probe method. The conductivity was recorded to be as high as 105 × 10 2S cm 1for the nanocomposite with a nanometer size structure and homogeneously distributed morphology. The electroactivity of the nanocomposites was approved by cyclic voltammetry(CV) and impedance spectroscopy technique(EIS). The antioxidant ability and thermal property of the composites were further studied. Preliminary studies have evidenced the production of conductive nanocomposites with good thermal property and relatively good solubility in N-methyl 2-pyrrolidone(NMP), with the antioxidant activity reaching up to 80%.     

Investigation on surface properties of superhydrophobic nanocomposites based on polyvinyl chloride and correlation with cell adhesion behavior

The main aim was to study the roles of structural homogeneity and superhydrophobicity on the adhesion of SW colon cancer cells on the surface of polyvinyl chloride (PVC) nanocomposites. Concurrent use of a proper nonsolvent (ethanol) and silica nanoparticles resulted in superhydrophobic behavior and also different surface structures. The effect of added‐ethanol content on the surface properties of PVC nanocomposites was also studied. The synergetic combination of silica and ethanol has led to the formation of a porous surface layer resulting in a considerable boost in the hydrophobic behavior. The scanning electron microscopy, roughness, and X‐ray photoelectron spectroscopy (XPS) analysis results were all in total agreement indicating the substantial change in surface morphology, topography, and composition once the ethanol content was increased to 50 vol.%. The surface structure was notably changed by the addition of polyhedral oligomeric silsesquioxanes (POSS) nanoparticles. It was found that the induced inhomogeneity as a result of POSS addition had an adverse effect on the surface properties. In conclusion, superhydrophobicity could be regarded as a prerequisite for achieving cell‐repellent behavior, but it cannot guarantee a cell repellent surface especially if the surface layer possesses structural inhomogeneity.     

Optical and electrical conducting properties of Polyaniline/Tin oxide nanocomposite

Polyaniline(PANI)/Tin oxide (SnO₂) hybrid nanocomposite with a diameter 20–30 nm was prepared by co-precipitation process of SnO₂ through in situ chemical polymerization of aniline using ammonium persulphate as an oxidizing agent. The resulting nanocomposite material was characterized by different techniques, such as X-ray diffraction (XRD), Transmission Electron Microscopy (TEM), Fourier Transform Infrared spectroscopy (FT-IR) and Ultraviolet–Visible spectroscopy (UV–Vis), which offered the information about the chemical structure of polymer, whereas electron microscopy images provided information regarding the morphology of the nanocomposite materials and the distribution of the metal particles in the nanocomposite material. SEM observation showed that the prepared SnO₂ nanoparticles were uniformly dispersed and highly stabilized throughout the macromolecular chain that formed a uniform metal-polymer nanocomposite material. UV–Vis absorption spectra of PANI/SnO₂ nanocomposites were studied to explore the optical behavior after doping of nanoparticles into PANI matrix. The incorporation of SnO₂ nanoparticles gives rise to the red shift of π–π¹ transition of polyaniline. Thermal stability of PANI and PANI/SnO₂ nanocomposite was investigated by thermogravimetric analysis (TGA). PANI/SnO₂ nanocomposite observed maximum conductivity (6.4 × 10^?3 scm^?1) was found 9 wt% loading of PANI in SnO₂.     

氧化钴和氮掺杂碳纳米管纳米复合物的催化与容量性质(英文)

The nanocomposites based on cobalt oxide and nitrogen-doped carbon nanofibers (N-CNFs) with cobalt oxide contents of 10–90 wt% were examined as catalysts in the CO oxidation and supercapacity electrodes. Depending on Со3О4 content, such nanocomposites have different morphologies of cobalt oxide nanoparticles, distributions over the bulk, and ratios of Со3+/Co2+ cations. The 90%Со3О4-N-CNFs nanocomposite showed the best activity because of the increased concentration of defects in N-CNFs. The capacitance of electrodes containing 10%Со3О4-N-CNFs was 95 F/g, which is 1.7 times higher than electrodes made from N-CNFs.     

An optical, EPR and electrical conductivity study of blue barium titanate, BaTiO3−δ

The electronic UV–VIS–NIR absorption spectra of single crystalline BaTiO_3−δ (BTO) are studied in the temperature range of 102–1173 K in pure oxygen and at conditions of moderate and strong reduction of the material. The strongly reduced crystals are of deep blue colour. The optical spectra of blue BTO are characterised by a strong absorption in the NIR region at around 7000 cm⁻¹, which is attributed to polaronic defects associated with the formation of Ti³⁺ in the material. This assumption is supported by fits of the spectra using polaronic line shape functions appropriate for disordered systems and also by the electrical conductivity of blue BTO which, in agreement with results from the optical spectra, exhibits an activation energy of 0.20 eV. The EPR spectra of moderately reduced BTO powders show an anisotropic g-factor, which is compatible with the optical spectrum. The temperature dependence of the band gap energy of BTO was found to be given as dE_g/dT = −7.21 × 10⁻⁴ eV/K.     

Synthesis,characterization and antibacterial properties of a novel nanocomposite based on polyaniline/polyvinyl alcohol/Ag

In this study, a novel nanocomposite based on polyaniline/polyvinyl alcohol/Ag (PANI/PVA/Ag) has been successfully synthesized. The chemical reduction method was used to produce Ag nanoparticle colloidal solution from Ag⁺ ions. The polymerization of aniline occurred in situ for the preparation of polyaniline (PANI) in the presence of ammonium persulfate. With exposure to Ag nanoparticles on the PANI/PVA composite, a new nanocomposite was obtained. The morphology and particle size of the novel nanocomposite was studied by scanning electron microscopy (SEM), X-ray diffraction (XRD), and Fourier transform infrared (FT-IR) analyses. According to XRD analysis, the size of nanoparticles was found to be in the range of 10–17 nm. SEM images showed the favored shape of nanoparticles as triangle which is a benign shape for antibacterial analysis. The antibacterial activity of the obtained nanocomposite was also evaluated against Gram positive bacteria Staphylococcus aureus (Staph. aureus) and Gram negative Escherichia coli (E. coli) using the paper disk diffusion method. The antibacterial study showed that the PANI/PVA composite did not have a very good antibacterial activity but PANI/PVA/Ag nanocomposites were found to be effective against two bacteria.