小口径轴对称收缩喷嘴射流冲击大平板噪声指向特性研究

实验研究了3毫米口径轴对称收缩喷嘴在各种压比下射流垂直冲击和倾斜冲击坚固大平板产生的噪声的指向特性。发现噪声在过平板法线和喷嘴轴线的平面内呈近似四瓣分布，当喷嘴与平板距离减小时，指向壁射流下游的瓣得到增强，反之，指向喷嘴上游的瓣得到增强。喷嘴压比增加时，指向壁射流下游的瓣得到增强，反之，指向喷嘴上游的瓣得到增强。根据自由射流噪声的基本指向特性、射流冲击噪声基本指向特性、声波在平板处发生镜面反射和声波能量叠加的设定，建立了一个冲击射流总体噪声指向特性的模型，成功解释了实验结果，并揭示了形成冲击射流总体噪声指向特性的内在机理。     

气枪喷嘴高速射流的除水效率研究

为揭示喷嘴除水的机理并进而对气枪喷嘴进行改进和优化设计,本文提出了利用图像分析处理对小尺度气枪喷嘴高速冲击乘风破浪的除水效率的研究方法。该方法将有效除水面积作为衡量喷嘴除水效率的标准,从面实现了对喷嘴整体除水效率的定量测量,并利用该方法对影响气枪喷嘴除水效率的各种因素（一次侧压力,喷嘴到平板的距离和射流攻角）进行了研究,并将实验结果与用热线风速仪及总压探头测量的结果进行了比较,得到冲击射流在平板水平速度分量是蚊蝇 嘴除尘除水效率的决定性因素等结论。     

旋流喷嘴中空旋转射流近区域流动的研究

从理论上分析了旋流喷嘴喷出的中空射流近区域的液膜的运动,在只考虑液膜表面张力的作用下,应用质量守恒和动量定理,建立了描述液膜运动的非线性常微分（积分）方程组,该方程组可以用数值方法方便地求解,结果表明,液体离开旋流喷嘴后在自由空间形成的液膜呈葫芦形状,其速度和液膜厚度等都周期性地变化。本结果是在液厝受拓动失称碎成液滴前的最基本运动状态,可以在射流的近区域内实验观察到,也是进一步从理论液膜破碎雾化过     

小口径轴对称收缩喷嘴射流冲击大平板噪声特性的实验研究

为研究小口径喷嘴冲击射流的噪声特性，测定了3mm口径的轴对称收缩喷嘴在各种压比情况下产生的亚音速和超音速射流冲击坚固大平板产生的噪声。发现噪声在空间呈近似四瓣分布，当喷嘴与平板距离减小时，噪声指向壁射流下游的瓣到增强，反之，噪声指向喷嘴上游的瓣得到增强。噪声随喷嘴距平板距离的增加呈增强的趋势，在距平板一定距离内有锯齿现象。噪声随喷嘴压比的增加而增强，相应于各种工况，存在一不同的压比值，此压比之前，噪声随压比的增大而迅速提高，但有起伏现象，在此压比之后，噪声平缓地随压比的增大而增强。     

应用保角变换法的亚音速矩形湍流射流理论研究

为求解亚音速矩形湍流射流的速度场结构,采用复变函数中的保角变换法将圆形喷口平面转化为矩形喷口平面;进而将已有的关于轴对称喷口射流流场的相关理论拓展到矩形喷口射流研究中,避免了在数值模拟中引入辅助方程、离散化、设置边界条件来求解三维N-S方程。通过该方法得到了矩形喷口宽高比AR分别为2、4、8时对射流结构的定量影响;求出了喷口尺寸为1×5mm2、喷口马赫数Ma=0.3时,喷口对称中心的宽、窄对称面内的速度云图。结果表明:宽高比AR越大,射流核心段长度越长,轴向衰减越慢;喷口面积为10cm2、20cm2时,加大宽高比可以缩短核心段长度且可加快轴向速度衰减,在射流宽、窄对称面都存在射流核心区与衰减区。首次提出速度分布的"马鞍面"主要集中在射流核心段内。通过与现有实验研究结果对比发现:核心段长度误差最小达到30%;轴向速度分布与实验结果吻合度也很高,误差在5%以内。因此,本文理论研究的正确性得到验证。本文所得结论可为进一步研究亚音速矩形射流结构与矩形喷口参数优化设计提供参考。     

不定原点喷嘴射流中流体物理的实验研究

为了能够更好地了解不定源喷嘴（indeterminate origin nozzle）射流中的物理过程，本文应用平面激光诱导荧光技术对一个大尺度的水射流进行了实验研究。流场显示的实验结果表明不定源喷嘴在射流的剪切层引入了蘑菇形反向旋转的涡对。这些涡的矢量方向与射流方向相同或相反，被称为流向涡（streamwise vortex）。由于射流中存在开尔文一亥姆霍兹不稳定，每当一个横向涡（spanwisevortex，即涡的矢量方向与射流方向垂直）从喷嘴脱流时会产生瞬时的低压，该瞬时低压促使向内发展的流向涡对在喷嘴的凹槽处生成。这些涡对在向下游流动的过程中会重组并在喷嘴的尖峰面生成向外发展的涡对。这些流向涡极大地影响了射流的发展。流向涡与横向涡的相互作用促使射流更早地发展成为湍流。由于流向涡同时也在射流中引入了径向的剪切流动，因此导致了更多的湍流生成从而增强了射流与周围流体的混合。     

熔喷双槽形喷嘴气体射流流场初探

在熔喷非织造布加工中,气体射流作为工作介质使聚合物熔体实现拉伸,气体射流流场的研究对熔喷气流拉抻数学模型研究非常重要。熔喷双槽形喷嘴形成的流场可以看作两股平面射流的合成。从单个点涡的性质出发,研究了涡偶的性质和涡偶代替射流的可行性。研究表明,在喷丝孔轴线附近,涡偶和射流的速度分布趋势相同,且有比较相近的速度分布,从而说明以涡偶代替射流是可行的。在此基础上,用两个涡偶分别代替两股射流,然后进行合成,推导出两股射流合成后速度分布的理论公式,该公式的计算结果与实验结果吻合较好。将该公式引入熔喷气流拉伸数学模型,预测出的纤维直径与采用经验公式时的预测结果几乎完全相同。结果表明,应用涡偶代替射流推导出的气流速度分布公式能够较好地描述熔喷双槽形喷嘴气体射流流场,可以用于完善熔喷气流拉伸数学模型。     

不定原点喷嘴射流中流体物理的实验研究

为了能够更好地了解不定源喷嘴(indeterminate origin nozzle)射流中的物理过程,本文应用平面激光诱导荧光技术对一个大尺度的水射流进行了实验研究.流场显示的实验结果表明不定源喷嘴在射流的剪切层引入了蘑菇形反向旋转的涡对.这些涡的矢量方向与射流方向相同或相反,被称为流向涡(streamwise vortex).由于射流中存在开尔文-亥姆霍兹不稳定,每当一个横向涡(spanwise vortex,即涡的矢量方向与射流方向垂直)从喷嘴脱流时会产生瞬时的低压,该瞬时低压促使向内发展的流向涡对在喷嘴的凹槽处生成.这些涡对在向下游流动的过程中会重组并在喷嘴的尖峰面生成向外发展的涡对.这些流向涡极大地影响了射流的发展.流向涡与横向涡的相互作用促使射流更早地发展成为湍流.由于流向涡同时也在射流中引入了径向的剪切流动,因此导致了更多的湍流生成从而增强了射流与周围流体的混合.     

入口扰动频率对矩形射流影响的大涡模拟

为研究入口扰动对矩形射流的影响,对不同扰动频率下的三维矩形射流进行了大涡模拟,用分布投影法求解动量方程,对压力泊松方程采用FACR直接解法.计算结果预报的速度在横向的单峰分布和速度半宽沿流向的近似线性增长与实验结果吻合良好.计算结果表明扰动频率为射流的本征频率fe=0.22时射流的卷吸作用最强,而高频扰动则抑制卷吸作用;激励频率接近本征频率时射流提前出现速度在展向的马鞍型双峰分布,更早趋于圆射流形态.进一步的流场二维和三维瞬态涡结构图谱表明:上述现象与f=0.1和f=0.22时射流近场更频繁卷起、更丰富的大涡结构存在密切关系,正是这些大涡运动不断地在横向卷吸入外界流体,实现射流在横向的迅速扩展.     

展向喷嘴湍流横向射流大涡模拟及其统计分析

采用大涡模拟方法数值模拟了展向椭圆喷嘴的湍流横向射流,对其大尺度结构的时空演化和湍流脉动速度场的时间序列分析、频谱分析、PDF分析以及时、空截面上的统计平均特性进行分析.结果表明,在射流出口附近的下游核心区中速度脉动剧烈,显现出明显的湍流特征.除了三维涡环脱落、扭曲、变形、摆动所对应频率之外,还存在很宽的湍流基频,它与在喷嘴出口附近产生的三维涡环的时空演化过程密切相关.由于展向椭圆喷嘴的湍流横向射流中的三维涡环快速脱落和强相互作用导致射流尾迹中的强湍流脉动,展向椭圆喷嘴湍流横向射流的PDF空间演化特征结构复杂.在射流核心区的湍流偏应力变化平缓,其统计平均值分布接近左右对称.展向椭圆喷嘴的湍流横向射流脉动速度场具有极为复杂的统计行为,与流向椭圆喷嘴相比具有更好的掺混能力.     

Flow Regimes of Interaction of a Turbulent Plane Jet into a Rectangular Cavity: Experimental Approach and Numerical Modelling

The present work is devoted to the experimental and numerical study ofthe interaction of a turbulent plane jet with a rectangular cavity.Several flow regimes have been found to occur: the non-oscillationregime, the stable oscillation regime and an unstable oscillationregime. The first two regimes have been particularly considered. Theexperimental study has been carried out using hot wire anemometry andsome visualisations. The numerical predictions based on statisticalmodelling have been made using on the one hand the standard k– model and on the other hand a two-scales split spectrum model. The structuralproperties of the flow have been described for the different situations.For the oscillatory regime, a parametrical study allowed to determinethe influence of the jet exit location and the Reynolds number on thefrequency of the jet flapping. The one point closures have been able topredict the oscillatory regime, and in particular the two-scales modelled to improved results because better account is taken of lag effectsin unsteady non-equilibrium situations.     

Effect of the Streamwise Component of the Vorticity Formed in a Turbulent Jet Source on the Acoustic Characteristics of the Jet

The results of an experimental study of the effects of different nozzle heads on turbulent jet noise are analyzed. A configuration of four cylindrical heads, tabbed heads, and chevron nozzles are considered and the decreases in the acoustic-mechanical efficiency of the jet (acoustic power reduction) for jets exposed to different modes of action are compared.It is shown that the effects of tabbed and cylindrical heads, as well as of chevrons, share a common property which is associated with the occurrence of vorticity in the jet source and can be described on the basis of a unified criterion characterizing the action on both the jet flow structure and the jet noise.     

Turbulent Structure of a Gas-Liquid Impinging Jet

The turbulent structure of a submerged axisymmetric impinging jet containing small gas bubbles is studied experimentally under conditions of periodic external excitation. On the basis of measuring the surface-friction pulsatory component in the jet impinging on an obstacle, the effect of the suppression of large-scale eddies at large gas volume fractions is registered. The conditions of resonant growth of coherent structures and the suppression of wide-band turbulence are determined for both the single-phase and the two-phase impinging jet. An analysis of the development of different pulsatory friction components in the impinging-jet gradient region is presented.     

半封闭狭缝湍流冲击射流的数值模拟

将Yakhot和Orszag提出的RNGk-ε模型推广应用于半封闭狭缝冲击射流场的数值模拟，以评价该模型对这种复杂湍流的预测能力。将计算得到的流场平均速度分布、湍流强度分布和流函数分布与标准k—ε模型的预测结果以及相应的实验数据进行了比较，结果表明：RNGk—ε模型的预测结果总体上要好于标准k—ε模型，但与实验值相比，所有预测结果都还存在不同程度的误差，尤其是近壁区和滞止点较远下游处的湍流强度分布。说明RNG模型虽然已在某些湍流的预测中取得了一定的成功，但要定量准确地预测冲击射流场，还必须针对其流动特征对模型加以改进。     

微型射流涡流器对湍流边界层控制的数值研究

运用数值方法,模拟出展向分布的同向倾斜微型射流列与平板湍流边界层相互作用形成流向涡列的流场结构,验证了利用其来对湍流边界层进行控制的可能性.随射流间距减小,流向涡列控制作用流向渗透能力增强,但作用区域减小;随射流速度提高,流向涡列控制作用增强,但过大的射流速度反而会导致流向涡列在局部区域内控制作用的下降;随射流俯仰角减小、倾斜角增大,流向涡列初始控制作用增强,但过小的俯仰角、过大的倾斜角会导致流向涡列流向控制区域明显缩小.要保证流向涡列具有较强的湍流边界层控制作用,必须通过合理配置射流列各主要参数,在保证各流向涡具有一定强度的同时,还要确保各流向涡在形成时部分嵌入边界层内部.     

Effect of Sudden Expansion on Entrainment and Spreading Rates of a Jet Issuing from Asymmetric Nozzles

Turbulent free jets issuing from five different nozzle geometries; smooth pipe, contracted circular, rectangular, triangular, and square, are experimentally investigated by using TSI 2-D laser Doppler velocimetry (LDV) to assess the effect of nozzle geometry and quarl (i.e. a cylindrical sudden expansion) on jet entrainment and spreading. The centerline mean velocity decay and the jet half-velocity width, which are indicators of jet entrainment and spreading rates, are determined for each nozzle’s flow configuration, i.e. with and without sudden expansion. Furthermore, turbulence quantities, such as the flow mean velocities and their mean fluctuating components, as well as Reynolds shear stresses, are all measured along the centerline plane of the jet to facilitate understanding the extent of the effect of nozzle’s geometry (i.e. nozzle’s orifice shape and sudden expansion) on jet’s entrainment and spreading. The main results show that the jet flow with the presence of sudden expansion exhibits higher rates of entrainment and spreading than without. In addition, these results reveal that sudden expansion exercises a greater effect on the asymmetric jet characteristics, especially for the triangular and rectangular nozzles compared to their axisymmetric counterparts (i.e. circular contracted nozzle).     

Mixing Intensification on the Edge of a Jet by Means of Longitudinal Vortices

The action of an artificially generated spanwise flow in the form of periodical longitudinal vortices on a plane turbulent mixing layer is investigated. It is shown that the disturbances result in a significant increase in the thickness of the mixing region. For two kinds of spanwise flow, namely, vortices whose centers lie in the plane separating the streams and vortices located above this plane, the dependence of the mixing layer thickness on the vortex amplitude and vertical dimension and on the longitudinal coordinate is found.     

The Interaction between a Compressible Synthetic Jet and a Laminar Hypersonic Boundary Layer

Numerical simulations have been performed of a synthetic jet interacting with a laminar hypersonic boundary layer. Two datum cases were also considered, no jet and steady jet. The simulations for the case of no jet are in agreement with available experimental data. Predicted flow features of the steady jet interaction are broadly consistent with previous studies. For the synthetic jet, the upstream and downstream separated regions are dramatically reduced in size, and the jet appears to lie closer to the surface, compared with the steady jet. It is also found that the synthetic jet induces a greater mixing rate than the steady jet. This revised version was published online in July 2006 with corrections to the Cover Date.     

自由湍射流边界层标度律的实验测量

用IFA300热线风速仪以低于最小低湍流时间尺度的高分辨率，精细测量了圆自由射流中同一流向断面内不同径向位置的流向速度分量，研究了不同径向位置的非均匀、非各向同性对充分发展湍流速度结构函数自相似标度律及其层次结构模型的影响。     

Jet Flow Past a Plate with a Spoiler in the Presence of a Stagnation Zone

An exact analytical solution of the problem of the jet flow past a flat plate with a spoiler is obtained for the case in which there is a stagnation zone near the spoiler. The Chaplygin method of singular points and the theory of elliptic theta-functions are used to construct the solution. The pressure in the stagnation zone is determined from the Brillouin-Villat condition of smooth separation. It is found that the lift and drag coefficients, considered as functions of the stagnation zone length, have extrema at points corresponding to the smooth separation condition.