Direct measurement of the internal electron quasi-Fermi level in dye sensitized solar cells using a titanium secondary electrode

The spatial dependence of the electron quasi-Fermi level (QFL) in the interior of dye sensitized nanocrystalline solar cells (DSC) under short circuit conditions can be inferred from calculations based on a diffusive electron transport model. The calculations predict that the difference in the QFL between the electrolyte and contact sides of the TiO(2) layer under short circuit conditions at 1 sun could be as much as 0.5-0.7 eV. The predicted QFL profiles depend on assumptions made about energy positions, electron mobility, and the conduction band density of states. In this work, the position of the QFL at the electrolyte side of the dye sensitized TiO(2) film in a DSC has been measured using a thin passivated titanium contact deposited on top of the nanocrystalline TiO(2) by evaporation. The method allows changes in the electron QFL at all points on the IV characteristic of the cell to be monitored under dark and photostationary conditions. In addition, cells incorporating the titanium electrode can give information about the behavior of the QFL under dynamic conditions.     

Influence of surface area on charge transport and recombination in dye-sensitized TiO2 solar cells

The dependence of the electron transport and recombination dynamics on the internal surface area of mesoporous nanocrystalline TiO2 films in dye-sensitized solar cells was investigated. The internal surface area was varied by altering the average particle size in the films. The scaling of the photoelectron density and the electron diffusion coefficient at short circuit with internal surface area confirms the results of a recent study (Kopidakis, N.; Neale, N. R.; Zhu, K.; van de Lagemaat, J.; Frank, A. J. Appl. Phys. Lett. 2005, 87, 202106) that transport-limiting traps are located predominately on the surfaces of the particles. The recombination current density was found to increase superlinearly (with an exponent of 1.40 +/- 0.12) with the internal surface area. This result is at odds with the expected linear dependence of the recombination current density on the surface area when only the film thickness is increased. The observed scaling of the recombination current density with surface area is consistent with recombination being transport-limited. Evidence is also presented confirming that photoinjected electrons recombine with redox species in the electrolyte via surface states rather than from the TiO2 conduction band.     

Calculation of activation energies for transport and recombination in mesoporous TiO2/dye/electrolyte films--taking into account surface charge shifts with temperature

Transient photovoltage and photocurrent measurements have been employed to determine the recombination and transport kinetics in operating dye-sensitized photovoltaic cells as a function of potential and temperature. Photocurrent transients have been taken at the open circuit potential, as opposed to the standard measurement at short circuit. Kinetic results have been used to calculate the activation energy as function of the Fermi level position in the TiO(2). In the calculation of activation energies, we have explicitly taken into account the temperature dependence of the offset between the electrolyte redox potential and the conduction band edge. This new method gives activation energies that decrease linearly as the Fermi level position moves toward the conduction band edge, as expected, but not found in previous studies. The results are consistent with the presence of a distribution of traps below the TiO(2) conduction band, the detrapping from which limits both the transport and the recombination of electrons.     

Cyanobacterial chlorophyll as a sensitizer for colloidal TiO2

Chlorophyll has been extracted from cyanobacteria. The adsorption of chlorophyll on the surface of colloidal TiO(2) through electrostatic interaction was observed. The apparent association constant (K(app)) of chlorophyll-TiO(2) obtained from absorption spectra is 3.78x10(4)M(-1). The K(app) value of chlorophyll-TiO(2) as determined from fluorescence spectra is 1.81x10(4)M(-1), which matches well with that determined from the absorption spectra changes. These data indicate that there is an interaction between chlorophyll and colloidal TiO(2) nanoparticle surface. The dynamics of photoinduced electron transfer from chlorophyll to the conduction band of colloidal TiO(2) nanoparticle has been observed and the mechanism of electron transfer has been confirmed by the calculation of free energy change (DeltaG(et)) by applying Rehm-Weller equation as well as energy level diagram. Lifetime measurements gave the rate constant (k(et)) for electron injection from the excited state chlorophyll into the conduction band of TiO(2) is 4.2x10(8)s(-1).     

Characterization of solid-state dye-sensitized solar cells utilizing high absorption coefficient metal-free organic dyes

Solid-state dye-sensitized solar cells were fabricated using the organic hole-transporting medium (HTM) 2,2'7,7'-tetrakis-(N,N-di-p-methoxyphenyl-amine)-9,9'-spirobifluorene (spiro-MeOTAD), and three organic indoline-based sensitizer dyes with high molar extinction coefficients. The cells were characterized by several techniques, including spectral response measurements, photovoltage decay transients, intensity modulated photovoltage spectroscopy (IMVS), and charge extraction. The differences in apparent electron lifetime observed for cells fabricated using the three dyes are attributed in part to changes in the surface dipole potential at the TiO2/spiro-MeOTAD interface, which shift the TiO2 conduction band energy relative to the Fermi level of the HTM. These energy shifts influence both the open circuit voltage (as a result of changes in free electron density) and the short circuit current (as a consequence of changes in the overlap between the dye LUMO level and the conduction band). A self-consistent approach was used to derive the positions of the conduction band relative to the spiro-MeOTAD redox Fermi level for cells fabricated using the three dyes. The analysis also provided estimates of the free electron lifetime in spiro-MeOTAD cells. In order to evaluate the possible contribution of the adsorbed dyes to the observed changes in surface dipole potential, their dipole moments were estimated using ab initio density functional theory (DFT) calculations. Comparison of the calculated dipole contributions with the experimentally measured shifts in conduction band energy revealed that other factors such as proton adsorption may be predominant in determining the surface dipole potential.     

Interpretation of apparent activation energies for electron transport in dye-sensitized nanocrystalline solar cells

Electron transport in dye-sensitized nanocrystalline solar cells appears to be a slow diffusion-controlled process. Values of the apparent electron diffusion coefficient are many orders of magnitude smaller than those reported for bulk anatase. The slow transport of electrons has been attributed to multiple trapping (MT) at energy levels distributed exponentially in the band gap of the nanocrystalline oxide. In the MT model, release of immobile electrons from occupied traps to the conduction band is a thermally activated process, and it might therefore be expected that the apparent electron diffusion coefficient should depend strongly on temperature. In fact, rather small activation energies (0.1-0.25 eV) have been derived from time and frequency resolved measurements of the short circuit photocurrent. It is shown that the MT model can give rise to such anomalously low apparent activation energies as a consequence of the boundary conditions imposed by the short circuit condition and the quasi-static relationship between changes in the densities of free and trapped electrons. This conclusion has been confirmed by exact numerical solutions of the time-dependent generation/collection problem for periodic excitation that provide a good fit to experimental data.     

Ultrafast electron transfer between molecule adsorbate and antimony doped tin oxide (ATO) nanoparticles

Ultrafast transient IR spectroscopy has been used to examine the effect of doping on interfacial electron transfer (ET) dynamics in Re(dpbpy)(CO)(3)Cl (dpbpy = 4,4'-(CH(2)PO(OH)(2))2-2,2'-bipyridine) (ReC1PO(3)) sensitized ATO (Sb:SnO(2)) nanocrystalline thin films. In films consisting of particles with 0%, 2% and 10% Sb dopant, the rates of electron injection from the adsorbate excited state to ATO were independent of and the rates of the recombination increased with the doping level. The observed similar forward electron injection rates were attributed to negligible changes of available accepting states in the conduction band at the doping levels studied. The dependence of the recombination rate on conduction band electron density and a possible mechanism for the recombination process were discussed.     

Molecular adjustment of the electronic properties of nanoporous electrodes in dye-sensitized solar cells

Molecular modification of dye-sensitized, mesoporous TiO2 electrodes changes their electronic properties. We show that the open-circuit voltage (V(oc)) of dye-sensitized solar cells varies linearly with the dipole moment of coadsorbed phosphonic, benzoic, and dicarboxylic acid derivatives. A similar dependence is observed for the short-circuit current density (I(sc)). Photovoltage spectroscopy measurements show a shift of the signal onset as a function of dipole moment. We explain the dipole dependence of the V(oc) in terms of a TiO2 conduction band shift with respect to the redox potential of the electrolyte, which is partially followed by the energy level of the dye. The I(sc) shift is explained by a dipole-dependent driving force for the electron current and a dipole-dependent recombination current.     

Effect of layer-by-layer assembled SnO2 interfacial layers in photovoltaic properties of dye-sensitized solar cells

Ultrathin SnO(2) layers were deposited on FTO substrate by the layer-by-layer (LbL) self-assembly technique utilizing negatively charged 2.5 nm sized SnO(2) nanoparticles (NPs) and cationic poly(allylamine hydrochloride) (PAH). For the construction of dye-sensitized solar cells (DSC), the bulk TiO(2) layer was deposited over the (PAH/SnO(2))(n) (n = 1-10) and subsequently calcined at 500 °C to remove organic components. With introducing four layers of self-assembled SnO(2) interfacial layer (IL), the short circuit current density (J(sc)) of DSCs was increased from 8.96 to 10.97 mA/cm(2), whereas the open circuit voltage (V(oc)) and fill factor (FF) were not appreciably changed. Consequently, photovoltaic conversion efficiency (η) was enhanced from 5.43 to 6.57%. Transient photoelectron spectroscopic analyses revealed that the ultrathin SnO(2) layer considerably increased the electron diffusion coefficient (D(e)) in TiO(2) layer, but the electron lifetime (τ(e)) was decreased unexpectedly. The observed unusual photovoltaic properties would be caused by the unique conduction band (CB) location of the SnO(2), inducing the cascadal energy band matching among the CBs of TiO(2), SnO(2), and FTO.     

Photoacoustic measurement of electron injection efficiencies and energies from excited sensitizer dyes into nanocrystalline TiO2 films

Time-resolved photoacoustic calorimetry is used to measure the energy released upon injection of an electron from an electronically excited dye adsorbed to nanocrystalline TiO2 into the conduction band of this material. More energy is released when the environment of the dye is made less polar, because the energy of the dye-oxidized state has a more pronounced solvent dependence than the edge of the conduction band of the TiO2 semiconductor. Such energy dependences should be considered in the design of more efficient dye-sensitized solar cells.     

Photoinduced interaction between riboflavin and TiO(2) colloid

The adsorption of riboflavin on the surface of TiO(2) colloidal particles and the electron transfer process from its singlet excited state to the conduction band of TiO(2) were examined by absorption and fluorescence quenching measurements. The apparent association constants (K(app)) were determined. The quenching mechanism is discussed involving electron transfer from riboflavin to TiO(2).     

二氢吲哚类染料用于染料敏化太阳能电池光敏剂的比较

采用密度泛函理论(DFT)和含时密度泛函理论(TD-DFT)对四种二氢吲哚染料进行研究, 从中筛选出相对优秀的染料敏化太阳能电池光敏剂. 对前线分子轨道的计算表明, 二氢吲哚染料的前线分子轨道结构非常有利于染料激发态向TiO2电极的电子注入. 对真空中的紫外和可见光吸收光谱的计算表明, 二氢吲哚染料的吸收光谱与太阳辐射光谱匹配较好. 对染料分子的能级计算表明, 二氢吲哚染料的能级结构比较适合于I-/I-3作电解液的TiO2纳米晶太阳能电池的光敏剂. 二氢吲哚染料最低未占据分子轨道(LUMO) 能级均比TiO2晶体导带边能级高, 能够保证激发态染料分子高效地向TiO2电极转移电子. 二氢吲哚染料最高占据分子轨道(HOMO)的能级比I-/I-3能级低, 保证了失去电子的染料分子能够顺利地从电解液中得到电子. 与实验数据比较, 得出在提高染料敏化太阳能电池转换效率方面, 对染料的关键要求是LUMO能级的位置. 染料分子的稳定性是染料敏化太阳能电池使用寿命的关键因素. 通过对化学键键长的比较表明, 二氢吲哚染料的分子稳定性基本相同. 对计算结果的分析表明, 二氢吲哚染料1(ID1)的LUMO能级最高, 分子稳定性最好, 在酒精溶液中的吸收光谱与太阳辐射光谱匹配很好, 在同类染料中是较好的染料敏化太阳能电池光敏剂.     

Standing wave enhancement of red absorbance and photocurrent in dye-sensitized titanium dioxide photoelectrodes coupled to photonic crystals

The light harvesting efficiency of dye-sensitized photoelectrodes was enhanced by coupling a TiO(2) photonic crystal layer to a conventional film of TiO(2) nanoparticles. In addition to acting as a dielectric mirror, the inverse opal photonic crystal caused a significant change in dye absorbance which depended on the position of the stop band. Absorbance was suppressed at wavelengths shorter than the stop band maximum and was enhanced at longer wavelengths. This effect arises from the slow group velocity of light in the vicinity of the stop band, and the consequent localization of light intensity in the voids (to the blue) or in the dye-sensitized TiO(2) (to the red) portions of the photonic crystal. By coupling a photonic crystal to a film of TiO(2) nanoparticles, the short circuit photocurrent efficiency across the visible spectrum (400-750 nm) could be increased by about 26%, relative to an ordinary dye-sensitized nanocrystalline TiO(2) photoelectrode.     

pH-dependent electron transfer from re-bipyridyl complexes to metal oxide nanocrystalline thin films

Photoinduced interfacial electron transfer (ET) from molecular adsorbates to semiconductor nanoparticles has been a subject of intense recent interest. Unlike intramolecular ET, the existence of a quasicontinuum of electronic states in the solid leads to a dependence of ET rate on the density of accepting states in the semiconductor, which varies with the position of the adsorbate excited-state oxidation potential relative to the conduction band edge. For metal oxide semiconductors, their conduction band edge position varies with the pH of the solution, leading to pH-dependent interfacial ET rates in these materials. In this work we examine this dependence in Re(L(P))(CO)3Cl (or ReC1P) [L(P) = 2,2'-bipyridine-4,4'-bis-CH2PO(OH)2] and Re(L(A))(CO)3Cl (or ReC1A) [L(A) = 2,2'-bipyridine-4,4'-bis-CH2COOH] sensitized TiO2 and ReC1P sensitized SnO2 nanocrystalline thin films using femtosecond transient IR spectroscopy. ET rates are measured as a function of pH by monitoring the CO stretching modes of the adsorbates and mid-IR absorption of the injected electrons. The injection rate to TiO2 was found to decrease by 1000-fold from pH 0-9, while it reduced by only a factor of a few to SnO2 over a similar pH range. Comparison with the theoretical predictions based on Marcus' theory of nonadiabatic interfacial ET suggests that the observed pH-dependent ET rate can be qualitatively accounted for by considering the change of density of electron-accepting states caused by the pH-dependent conduction band edge position.     

Complex and charge transfer between TiO2 and pyrroloquinoline quinone

Pyrroloquinoline quinone (PQQ) forms a tridentate complex with coordinatively unsaturated titanium atoms on the surface of approximately 4.5 nm TiO2 particles; an association constant of K = 550 M-1 per Ti(IV)surf has been determined. Low-temperature electron paramagnetic resonance was employed in identification of localized charges and consequently produced radicals and in determination of charge-transfer processes. The photoexcitation of the PQQ-TiO2 complex results in the transfer of conduction band electrons from TiO2 to bound PQQ and the formation of the semiquinone radical. Attaching dopamine (DA) as an electron donor and PQQ as an electron acceptor on the surface of TiO2 results in spatial separation of photogenerated charges; the holes localize on dopamine and electrons on PQQ, with higher yields than for each component separately. In this triad-type assembly (PQQ-TiO2/DA) the PQQ that is bound to the particles acts as a sink for electrons allowing their almost complete scavenging even at temperature as low as 4 K.     

Spatial electron distribution and its origin in the nanoporous TiO2 network of a dye solar cell

Dye solar cells have been investigated by charge carrier extraction under short and open circuit conditions and an illumination intensity equivalent to 1 sun (AM 1.5). Under short circuit conditions, a surprisingly high amount of charge carriers stored in the nanoporous TiO2 network has been observed. A theoretical model was developed to describe the charge transport in the nanoporous TiO2 network of a dye solar cell, and the spatial distribution of the electron concentration was calculated. These results were compared with the experimental data of charge carriers stored in the TiO2 network under short and open circuit conditions. We were able to conclude that under short circuit conditions, the electrochemical potential of the electrons in the region far from the electrode is up to 550-570 meV higher than that of the electrons at the front electrode. This internal voltage is the driving force across the nanoporous TiO2 film under short circuit conditions.     

五甲川菁染料敏化p-NiO纳米结构电极的光电化学

研究了NiO纳米结构电极及五甲川菁染料敏化NiO纳米结构电极的光电化学行为。结果表明,NiO纳米结构电极在光照下产生阴极光电流,为p-型半导体,其禁带宽度为2.8eV,使用五甲川菁染料敏化可以显著地提高NiO纳米结构电极的阴极光电流,使NiO纳米结构电极吸收波长红移至可见光区,光电转换效率得到明显改善。研究了OTE/TiO~2/Ru(bpy)~2(SCN)~2和OTE/NiO/PMC作为光阳极和光阴极组成电池的电池特性,结果表明复合电池的光电压提高,但光电流的大小受光电流小的电极限制。     

Oligothiophene-containing coumarin dyes for efficient dye-sensitized solar cells

We have developed oligothiophene-containing coumarin dyes fully functionalized for dye-sensitized nanocrystalline TiO(2) solar cells (DSSCs). DSSCs based on the dyes gave good performance in terms of incident photon-to-current conversion efficiency (IPCE) in the range of 400-800 nm. A solar energy-to-electricity conversion efficiency (eta) of 7.4% was obtained with a DSSC based on 2-cyano-3-[5'-(1,1,6,6-tetramethyl-10-oxo-2,3,5,6-tetrahydro-1H,4H,10H-11-oxa-3a-aza-benzo[de]anthracen-9-yl)-[2,2']bithiophenyl-5-yl]acrylic acid (NKX-2677) under simulated AM 1.5G irradiation (100 mW cm(-2)) with a mask: short-circuit current density (J(sc)) = 13.5 mA cm(-2); open-circuit voltage (V(oc)) = 0.71 V; fill factor (FF) = 0.77. Transient absorption spectroscopy measurements indicated that electron injection from NKX-2677 to the conduction band of TiO(2) is very rapid (<100 fs), which is much faster than the emission lifetime of the dye (1.0 ns), giving a highly efficient electron injection yield of near unity.     

One-photon photodetachment of I- in glycerol: spectra and yield of solvated electrons in the temperature range 329<or=T<or=536 K

Solvated electrons in glycerol were generated via a resonant one-photon photodetachment of the charge-transfer-to-solvent (CTTS) band of I- in glycerol (Gl) after irradiation with a 248 nm excimer laser. Optical absorption spectra of solvated electrons (esolv-) in Gl were recorded as a function of temperature (381相似文献   

Influence of a TiCl4 post-treatment on nanocrystalline TiO2 films in dye-sensitized solar cells

In this study, the influence of the TiCl(4) post-treatment on nanocrystalline TiO(2) films as electrodes in dye-sensitized solar cells is investigated and compared to nontreated films. As a result of this post-treatment cell efficiencies are improved, due to higher photocurrents. On a microscopic scale TiO(2) particle growth on the order of 1 nm is observed. Despite a corresponding decrease of BET surface area, more dye is adsorbed onto the oxide surface. Although it seems trivial to match this finding with the improved photocurrent, this performance improvement cannot be attributed to higher dye adsorption only. This follows from comparison between incident photon to current conversion efficiency (IPCE) and light absorption characteristics. Since the charge transport properties of the TiO(2) films are already more than sufficient without treatment, the increase in short circuit current density J(SC) cannot be related to improvements in charge transport either. Transient photocurrent measurements indicate a shift in the conduction band edge of the TiO(2) upon TiCl(4) treatment. It is concluded that the main contribution to enhanced current originates from this shift in conduction band edge, resulting in improved charge injection into the TiO(2).