一种液晶环氧增韧环氧树脂的研究

环氧树脂具有优异的机械性能 ,耐高温以及良好的加工工艺性 .被广泛用于机械、航天、船舶等领域 .由于环氧树脂固化后断裂延伸率小 ,脆性大 ,使其应用受到了一定的限制 .为此 ,国内外学者对环氧树脂进行了大量的改性研究工作 .用含有“柔性链段”的固化剂固化环氧 ,在交联网络中引入柔性链段[1] ;在环氧基体中加入橡胶弹性体[2 ] 、热塑性树脂[3 ,4] 、液晶聚合物[5,6] 等分散相或用热固性树脂连续贯穿于环氧树脂网络中形成互穿、半互穿网络结构[7] ,以改善环氧树脂的韧性 .本文采用液晶环氧化合物原位复合增韧环氧树脂 ,考察了液晶环氧对环…     

环氧树脂/液晶聚合物体系的形态、力学性能和热稳定性

合成了一种端基含有活性基团的热致性液晶聚合物 (LCPU) ,用其改性环氧树脂CYD 12 8 4 ,4′ 二氨基二苯砜 (DDS)固化体系 ,对改性体系的冲击性能、拉伸性能、弯曲性能、弹性模量、断裂伸长率、玻璃化转变温度Tg、热失重温度TG与LCPU含量的关系进行了探讨 ,对不同种类液晶化合物改性CYD 12 8 DDS体系效果进行了比较 ,用扫描电镜 (SEM)研究了材料断面的形态结构 .结果表明 ,LCPU的加入可以使固化物的力学性能和热稳定性提高 ,改性后材料断裂面的形态逐渐呈现韧性断裂特征     

透闪石/环氧树脂复合材料性能研究

环氧树脂是一类综合性能较好的热固性树脂,为了扩大其应用范围．通常的办法是采用纤维进行增强．目前,许多研究工作者采用纳米粒子、粘土对其进行改性,所用的粘土包括各种有机蒙脱土、高岭土等,作者曾采用海泡石对环氧树脂进行改性,使环氧树脂的各项力学性能得以提高,然而采用透闪石对环氧树脂进行改性,还鲜见相关报道．透闪石是一种带有极性基团的天然矿物,     

Preparation and properties characterization of gallic acid epoxy resin/succinic anhydride bionanocomposites modified by green reduced graphene oxide

Graphene oxide was reduced into reducing-graphene oxide (r-GO) successfully using gallic acid (GA) as a green reducing agent. Biobased gallic acid epoxy resin (GAER) was synthesized from renewable GA, and the biobased GAER/r-GO nanocomposites and glass fiber-reinforced composites were prepared with succinic anhydride as a curing agent. The dynamic mechanical, thermal, and mechanical properties of the composites with varying r-GO contents were characterized. When the content of r-GO was 0.5 wt%, the glass transition temperature was 10.4°C higher than the pure resin system. The thermal and mechanical properties were increased with increasing r-GO content; when the r-GO content was 1.0 wt%, the initial degradation temperature was enhanced by approximately 6.8°C, the tensile and impact strengths were 34.5% and 49.1% higher, respectively, than the pure cured GAER. The impact strength of GAER was higher than that of the bisphenol A epoxy resin/SUA curing system, but the tensile strength was lower than it.     

High mechanical and thermal performance of Sasobit-modified epoxy resin,prepared via vacuum shock technique

In this study, thermal and mechanical properties of novel nanocomposite, epoxy resin reinforced with octadecylamine functionalized graphene oxide (GO-ODA) and Sasobit, prepared via creative vacuum shock technique, were investigated. By introducing 1, 3 and 5 wt% Sasobit to the neat epoxy resin, the tensile strength increased remarkably by 104%, 315% and 266%, respectively due to the unique stiff and crystalline structure of Sasobit. In addition, considerable enhancement of 125% in Young's modulus, 351% in toughness, 562% in impact resistance, ~19 °C in thermal stability and ~7 °C in glass transition temperature of epoxy resin with 3 wt% Sasobit loading was demonstrated. The composite containing 3 wt% Sasobit alone, were found to have even superior properties than GO-ODA/epoxy nanocomposite, as surprisingly 3, 2.9, 2.2 and 2 times more improvement, respectively in tensile strength, toughness, impact strength and thermal stability of epoxy resin compared to reinforcement with GO-ODA were obtained.     

含磷有机硅杂化环氧树脂固化体系性能研究

通过磷酸与γ-环氧丙氧基三甲氧基硅烷反应得到含磷有机硅氧烷,并加入到环氧树脂/4,4'-二氨基二苯基甲烷体系中混合,通过溶胶-凝胶的方法制备了含磷有机硅杂化环氧树脂固化物.对固化体系进行了玻璃化转变温度、热失重、阻燃、拉伸强度、冲击强度测试分析.结果表明,该固化体系的阻燃性得到提高,极限氧指数在25.8～29.3,玻璃化转变温度得到提高,在161～179℃;虽然初始分解温度比纯环氧树脂固化物低,但800℃残炭率可以达到26.5%,提高了36%;拉伸强度得到提高,在71～94 MPa,冲击强度可以达到14.36 kJ/m2,提高了14%.该固化体系具有较好的阻燃性能和热性能,同时具有较好的力学性能.     

Effect of Pickering emulsion on the mechanical performances and fracture toughness of epoxy composites

The improvement of mechanical properties and toughness of nanoparticles for epoxy composites was mostly dependent on the disperse state of nanoparticles in epoxy matrices. When the content of nanoparticles was higher than a threshold value, it was easy to aggregate and then affect the improvement effect. Pickering emulsion was prepared using SiO₂ nanoparticles as emulsifier and functional monomer as oil phase. The influence of Pickering emulsion on the curing process was investigated. The effect of Pickering emulsion on the mechanical properties, toughness, and glass transition temperature (Tg) was studied. Impact and tensile fracture surface were observed by scanning electron microscopy (SEM). Results from differential scanning calorimeter (DSC), tensile, impact, and fracture toughness tests are provided. The results indicated that the introduction of Pickering emulsion can eliminate the residual stress and accelerate curing reaction. Epoxy composites were capable of increasing tensile strength by up to 29.9%, impact strength of three‐fold, fracture toughness of 35%, and Tg of 20.7°C in comparison with the reference sample. SEM images showed that SiO₂ nanoparticles exhibit a good dispersion in epoxy matrix. The increases in mechanical properties, toughness, and Tg of epoxy composites were attributed to the “Second Phase Toughness” mechanism.     

Effects of nano ZnO on strength and stability of unsaturated polyester composites

ZnO–glass fiber–unsaturated polyester composites have been prepared. On exposure to the metal halide lamp, their resistance to ultraviolet (UV) degradation is evaluated. Experimental results show that ZnO can reduce the UV degradation of the unsaturated polyester matrix. ZnO can significantly retard the UV degradation process of the matrix resin, and can also increase the impact strength of the composites under the experimental conditions. Differential scanning calorimetry (DSC) analyses also indicate that the addition of ZnO to unsaturated polyester may retard the crosslink process and catalyze the decomposition of the resin. However, after more than 40 hr of UV irradiation, it was crosslinked. SEM fracture morphology shows that nano ZnO could hinder crack growth and induce more cracks, and when the content of ZnO reaches 6 wt%, the impact fracture mechanism changes abruptly and plastic deformation appears, which indicates that 6 wt% for ZnO in unsaturated polyester could be considered as the critical content. Around the critical content, the particles are near enough to interact with each other and this results in the change of fracture mechanism. The results also indicate that the proper content of ZnO added into an unsaturated polyester could prolong the durability and lessen the reject rate of transparent glass fiber–polyester composites. Copyright © 2008 John Wiley & Sons, Ltd.     

纳米级金红石型二氧化钛与受阻胺光稳定剂协同改进ABS的抗老化性能研究

分别采用纳米级金红石型TiO2和受阻胺光稳定剂(HALS)对ABS进行改性,通过熔融共混法制备了ABS/纳米TiO2、ABS/纳米TiO2/HALS和ABS/HALS复合材料,采用GB/T16422.2~1999所述的塑料实验室光源暴露实验方法,用氙灯气候试验机对其进行28天人工加速老化,通过测定其老化过程中的无缺口和缺口试样冲击强度的变化来对其抗老化性能进行表征,同时利用光学显微镜和扫描电镜对其老化过程中的冲击断口形貌变化进行了研究.结果表明,纳米TiO2在ABS基体中分散良好,改性后的复合材料均具有较好的抗老化性能,纳米TiO2与HALS复合改性ABS对其耐候性的提高具有明显的协同作用,其老化后的抗冲击性能超过了单一使用HALS或纳米TiO2的改性效果,老化28天后纯ABS树脂试样的无缺口冲击强度保持率只有20%左右,添加2.0 wt%纳米TiO2后,老化28天后的ABS/纳米TiO2/HALS复合材料试样的保持率则提高到47.9%,为纯ABS树脂试样的2.5倍.     

有机硅改性双酚A型环氧树脂研究

采用二氯二甲基硅烷 (DMS) ,或DMS与α ,ω 二氯聚二甲基硅氧烷 (DPS)的混合物来改性双酚A型环氧树脂 ,通过对固化物的冲击强度、拉伸强度、断裂伸长率和玻璃化转变温度 (Tg)的测定 ,探讨了改性方法、有机硅组成与含量等对材料性能的影响 .结果表明 ,用 5 7phr的DMS改性时 ,树脂固化物的冲击强度达2 0 2kJ m2 ,拉伸强度达 6 7 0MPa ,断裂伸长率达 11 2 9% ,Tg 达 16 8 0℃ ;分别比未改性时提高了 9 4kJ m2 ,2 1 1MPa ,5 4 %以及 32 6℃ .而用 0 7phrDMS +10phrDPS共同改性时 ,除Tg 和拉伸强度略有上升外 ,冲击强度达到了 31 6kJ m2 ,断裂伸长率达到 81 6 % ,分别比纯环氧提高了 2 0 8kJ m2 和 75 7% .     

Effect of internal mold release agent on flexural and inter laminar shear properties of carbon and glass fabric reinforced thermoset composites

The study is focused on thermoset composites reinforced with carbon and glass woven fabrics. Two types of thermoset resins, for example, epoxy and vinyl ester were used as the matrix. Varying concentrations of internal mold releasing (IMR) agent was used in the resin. The composites were cured both at room temperature and at 80°C. The flexural properties were studied using 3‐point bending test method. Further theinter‐laminar shear strength (ILSS) was investigated using the short beam shear strength test based on 3‐point bending. The flexural modulus of room temperature cured epoxy resin is higher than that of high temperature cured epoxy resin and cured vinyl ester resin. The flexural modulus is lowest for 1% IMR sample in epoxy system and the modulus for 0% and 2% epoxy are not significantly different. Lowest flexural strength and modulus can be observed for the combination of reinforcement and curing conditions for samples containing 1% IMR for the epoxy systems. Carbon fiber is found to be less compatible with the vinyl ester resin system and the addition of IMR to the resin degraded the properties further. Inter‐laminar shear strength for epoxy‐based composites is not much affected by presence of IMR, but in case of vinyl ester based composites there is a decrease in ILSS on addition of IMR agent. The study explains variation in flexural properties on addition of IMR and change of curing conditions. These results can be used for ascertaining variation in mechanical properties in real use.     

X-ray diffraction and X-ray photoelectron spectroscopy studies of Ni-P deposited onto carbon fiber surfaces: impact properties of a carbon-fiber-reinforced matrix

In this work, the Ni-P coating on carbon fiber surfaces was carried out in order to improve the impact resistance of carbon fibers-reinforced epoxy matrix composites. The fiber surfaces and the fracture behaviors of composites were measured in terms of X-ray diffraction spectrometry (XRD), X-ray photoelectron spectrometry (XPS), scanning electron microscopy (SEM), and falling weight impact testing. From the XRD and XPS measurements, it was observed that Ni-P coating of carbon fibers led to an increase in two phases, i.e., microcrystalline and amorphous, mainly due to the increase of NiP(2), Ni(3)P, and Ni metal. Energy adsorbed by composites through the various fracture mechanisms was seen to be the characteristic distinguishing between nontreated and treated fiber-reinforced composite systems. The Ni-P alloy technique to improve the impact resistance of the composites was shown to be the modification of fiber-epoxy resin interfaces.     

Effect of preheat and encapsulation of steel particles on the interaction with Bisphenol A composites

In this study, the mechanical and thermal behavior of the steel particles (SP) fabricated epoxy-based composites were investigated. The purpose of using SP was to find out their suitability and compatibility to be used as low-cost fillers for epoxy-based composites. A special steel-cast metal mold was used to fabricate the composites via self-casting method. The effect of SP concentration (10, 20, 30 and 40 wt%) on various properties of the epoxy/SP composites was explored. Another sample was prepared using the optimum loading with a special treatment using heat and encapsulation of the SP. Mechanical properties of the composites were analyzed through tensile, flexural and impact testing. Fourier transform infrared spectroscopy (FTIR) and scanning electron microscopy (SEM) were used to examine the structural and morphological properties. In addition, thermal properties of the composites were analyzed with the thermogravimetric analyzer (TGA). Results indicated that the addition of PS into epoxy improved both tensile and flexural strength up to 98.5% and 147.6%, respectively, compared to the neat epoxy (NE). The decomposition temperature was raised nearly 18 °C for adding 30 wt% SP which was the maximum among all other composites. Results showed that 30 wt% of SP was the optimum loading for the better properties of the composites. In addition, the preheat treatment of the particles and the encapsulation process established a better interaction between the epoxy and the particles which resulted in the superior performance of the composites compared to the other samples. Overall, the improved mechanical and thermal properties of the SP-fabricated epoxy composites indicate that the epoxy/SP composite is a good candidate for structural and high temperature applications.     

Graphene oxide/epoxy composites with enhanced fracture toughness for liquid hydrogen storage

Graphene oxide (GO)/epoxy composites cured by aliphatic dibasic acids have been prepared. The influences of structure of aliphatic dibasic acid and loading of GO on curing process and mechanical properties of epoxy composites were studied. The results show that the reaction activities, gel time of corresponding epoxy-acid system and tensile strength of the formed epoxy resins decrease with the increase of the chain length of aliphatic dibasic acids. Both fracture toughness (>1.96 MPa⋅m^1/2) and elongations at break (>6%) increase with the increase of the chain length of aliphatic dibasic acids. The introduction of GO is helpful to increase the mechanical properties and the gas transmission coefficient of GO/epoxy composites. A maximum of tensile strength and elongations at break were obtained when the loading of GO is 0.6 wt%. The gas transmission coefficient of GO/epoxy composite increases with the increase of GO loading. The excellent mechanical properties and gas leakage resistance coefficient of the formed epoxy composites provides potential application in many fields where conventional brittle epoxy resins are inapplicable.     

Studies on thermal, mechanical and morphological behaviour of caprolactam blocked methylenediphenyl diisocyanate toughened bismaleimide modified epoxy matrices

Diglycidyl ether of bisphenol A epoxy resin (DGEBA, LY 556) was toughened with 5%, 10% and 15% (by wt) of caprolactam blocked methylenediphenyl diisocyanate (CMDI) using 4,4′-diaminodiphenylmethane (DDM) as curing agent. The toughened epoxy resin was further modified with chemical modifier N,N′-bismaleimido-4,4′-diphenylmethane (BMI). Caprolactam blocked methylenediphenyl diisocyanate was synthesized by the reaction of caprolactam with methylenediphenyl diisocyanate in presence of carbon tetrachloride under nitrogen atmosphere. Thermal properties of the developed matrices were characterized by means of differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), heat distortion temperature (HDT) and dynamic mechanical analysis (DMA). Mechanical properties like tensile strength, flexural strength and impact strength were tested as per ASTM standards. The glass transition temperature (T_g) and thermal stability were decreased with increase in the percentage incorporation of CMDI. The thermomechanical properties of caprolactam blocked methylenediphenyl diisocyanate toughened epoxy resin were increased by increasing the percentage incorporation of bismaleimide. The values of impact strength for epoxy resin were increased with increase in the percentage concentration of CMDI. The homogeneous morphology of CMDI toughened epoxy resin and bismaleimide modified CMDI toughened epoxy resin system were ascertained from scanning electron microscope (SEM).     

Statistical Analysis of Polymer Nanocomposites for Mechanical Properties

Epoxy resins, due to their high stiffness, ease of processing, good heat, and chemical resistance obtained from cross-linked structures, have found applications in electronics, adhesives coatings, industrial tooling, and aeronautic and automotive industries. These resins are inherently brittle, which has limited their further application. The emphasis of this study is to improve the properties of the epoxy resin with a low-concentration (up to 0.4% by weight) addition of Multi-Walled Carbon Nanotubes (MWCNTs). Mechanical characterization of the modified composites was conducted to study the effect of MWCNTs infusion in the epoxy resin. Nanocomposites samples showed significantly higher tensile strength and fracture toughness compared to pure epoxy samples. The morphological studies of the modified composites were studied using Scanning Electron Microscopy (SEM).     

Polyimide incorporated cyanate ester/epoxy copolymers for high-temperature molding compounds

The rapid development of high-power devices has driven the requirement for high-temperature stable epoxy molding compounds. In this work, a designed polymer blend system consisting of cyanate ester/epoxy copolymers modified by polyimide (CE/EP-PI) has been studied. Polyimide used in this study has shown excellent dispersity in the cyanate ester and epoxy copolymer network (CE/EP), exhibiting homogeneous phase with a denser polymer network structure. With this polymer blend structure, CE/EP-PI system was proved to have a glass transition temperature as high as ~270 °C, increased modulus, and largely enhanced fracture toughness up to 2.06 MPa m^1/2. CE/EP-PI resins showed outstanding long-term stability at high temperature with low mass loss and increased fracture toughness after aging at 200 °C. This work provides a novel insight into the development of molding compounds based on polymer blends system with excellent high-temperature properties. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 2412–2421     

Preparation and cryogenic mechanical properties of epoxy resins modified by poly(ethersulfone)

A thermoplastic, poly(ethersulfone) (PES) was used to modify a bisphenol‐F based epoxy resin cured with an aromatic diamine. The initial mixtures before curing, prepared by melt mixing, were homogeneous. Scanning electron microscopy (SEM) micrographs of solvent‐etched fracture surfaces of the cured blends indicated that phase separation occurred after curing. The cryogenic mechanical behaviors of the epoxy resins were studied in terms of tensile properties and Charpy impact strength at cryogenic temperature (77 K) and compared to their corresponding behaviors at room temperature (RT). The addition of PES generally improved the tensile strength, elongation at break, and impact strength at both RT and 77 K except the RT tensile strength at 25 phr PES content. It was interesting to observe that and the maximum values of the tensile strength, elongation at break, and impact strength occurred at 20 phr PES content where a co‐continuous phase formed. Young's modulus decreased slightly with the increase of the PES content. Moreover, the tensile strength and Young's modulus at 77 K were higher than those at RT at the same composition, whereas the elongation at break and impact strength showed the opposite results. Finally, the differential scanning calorimetry analysis showed that the glass transition temperature (T_g) was enhanced by the addition of PES. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 612–624, 2008     

中空多壳层TiO2填充对环氧树脂复合材料力学性能的影响

为改善环氧树脂(EP)材料的力学性能, 采用次序模板法合成了TiO₂中空多壳层结构(HoMS)材料, 利用偶联剂对获得的TiO₂ HoMSs进行接枝改性后填充到EP中, 制备了TiO₂ HoMSs/EP复合材料; 并与单壳层TiO₂中空结构进行比较, 研究了壳层数和偶联剂改性对复合材料力学性能的影响规律. 结果表明, 随着壳层数的增加, 复合材料的力学性能增强, 并且偶联剂改性的TiO₂ HoMSs可进一步提高复合材料的力学性能. 在该体系中, 经硅烷偶联剂KH-560改性后的三壳层TiO₂ HoMSs(3S-TiO₂ HoMSs)/EP复合材料的拉伸强度、 断裂伸长率和冲击强度可分别达到71.66 MPa, 7.4%和35.81 kJ/m². 扫描电子显微镜(SEM)断面形貌表征结果显示, 相较于纯EP材料, TiO₂ HoMSs/EP复合材料的断面更加粗糙, 说明TiO₂ HoMSs材料起到了吸收外界应力和阻碍裂纹扩展的作用, 提高了复合材料的韧性, 提升了复合材料的冲击性能.     

Multi-layer nanopaper based composites

Native cellulose nanofibrils (CNF) were prepared from bleached birch pulp without any chemical or enzymatic pretreatment. These CNF were modified by adsorption of a small amount of water-soluble polysaccharides and used to prepare nanopapers, which were processed into composites by lamination with an epoxy resin and subsequently cured. The results were compared to the properties of composites prepared using bacterial cellulose nanopapers, since bacterial cellulose constitutes highly pure and crystalline cellulose. It was found that both types of nanopapers significantly improved both the thermal stability and mechanical properties of the epoxy resin. As anticipated, addition of only 2 wt% of water-soluble polysaccharides efficiently hindered crack-propagation within the nanopaper and significantly improved the tensile strength and work of fracture compared to composites containing a conventional nanopaper reinforcement. The mechanical properties of the composites thus reflected the improvement of the nanopaper properties by the polysaccharides. Moreover, it was possible to predict the properties of the final composite from the mechanical performance of the nanopapers.