Mn助剂对K-Co-Mo催化剂结构及CO加氢合成低碳醇性能的影响

通过溶胶-凝胶法合成了一系列Mn掺杂K-Co-Mo催化剂,并利用X射线衍射、N₂吸脱附、NH₃程序升温脱附、原位漫反射红外光谱以及X射线吸收谱等技术对催化剂的结构进行了表征.活性测试结果显示Mn掺杂催化剂比未掺杂催化剂表现更高的合成低碳醇的催化活性,尤其是C₂₊醇的选择性得到了明显的提高.醇产物分布偏离了ASF分布规律,甲醇的含量显著减少,乙醇成为主要醇产物.表征结果表明Mn助剂的加入增强了Co和Mo之间的相互作用,促进了醇生成活性中心Co-Mo-O物种的生成.显著减少了催化剂强酸性位的数量,促进了弱酸性位的产生,有利于醇产物的生成.助剂的加入有利于催化剂对CO的线性和桥式吸附,促进了醇产物的生成和碳链的增长,提高了催化剂对C₂₊醇的选择性.     

利用生物质合成气在钼基催化剂上制备混合醇

采用柠檬酸作络合剂的溶胶凝胶法制备了一系列的钼基催化剂,并应用到从生物质气化合成气有效合成低碳混合醇的实际过程中. 在钼基催化剂中,Cu₁Co₁Fe₁Mo₁Zn_0.5-6%K催化剂具有相对较高的混合醇时空产率. 通过实验发现, 反应温度在340 oC以下时,碳转化率随着反应温度的增加而不断上升,总醇的选择性却逐渐下降. 在试验测试的条件内,从生物质气化合成气合成的混合醇最大产率为494.8 g/(kg_catal·h),其中C2⁺醇(C2-C6高碳醇)占总醇含量的80.4%. 在不同的钼基催化剂上合成的混合醇,其醇分布除甲醇以外均符合Schulz-Flory方程. 在醇类产物中,C2以上的高级醇含量占总醇重量的百分比为70%-85%. 同时,利用X射线衍射和BET等表征手段对钼基催化剂的形态和结构进行了表征. 从生物质合成气生产的洁净生物质燃料混合醇具有较高的辛烷值,可以用作运输燃料或汽油的添加剂.     

光沉积Ru和RuO2的锐钛矿TiO2纳米片的光解水产氧

采用水热法以HF作为结构调控剂合成了主要暴露（001）面的锐钛矿TiO₂纳米片,通过光沉积方法分别合成了负载Ru和RuO₂物种的光催化剂。利用X射线衍射、透射电镜和氢气程序升温还原等分析表征了催化剂的结构性质。通过光解水产氧反应来研究催化剂的催化性能,详细考察了Ru含量、负载方式以及氧化和还原处理等因素的影响,光解水产氧速率的差异证明了Ru物种在不同晶面的电荷-空穴分离效应。与负载单一助催化剂的Ru/TiO₂和RuO₂/TiO₂样品相比,活性最优的0.5%Ru-1.0%RuO₂/TiO₂样品由于负载了双助催化剂,其催化活性得到更大的提高,证实了在锐钛矿TiO₂上的晶面电荷-空穴分离效应.     

焙烧温度对SiO2负载的Co3O4纳米粒子表面氧缺陷浓度和CO氧化催化性能的影响

以传统的浸渍法,在不同焙烧温度下制备了用于CO氧化反应的Co₃O₄/SiO₂催化剂．通过激光拉曼光谱(Raman)、X射线光电子能谱(XPS)、X射线衍射(XRD)、程序升温还原(TPR)和X射线吸收精细结构谱(XAFS)表征了该系列催化剂的结构．在所有的催化剂中,XRD和Raman光谱都只检测到了Co₃O₄晶相的存在．与Co₃O₄体相相比,XPS结果表明在200 oC焙烧的(Co₃O₄(200)/SiO₂)催化剂中Co₃O₄表面上存在着过量的Co²⁺．与XPS的结果一致,TPR结果表明Co₃O₄(200)/SiO₂催化剂中Co₃O₄表面上存在氧缺陷, 并且XAFS结果也表明Co₃O₄(200)/SiO₂催化剂中Co₃O₄具有更多的Co²⁺．提高焙烧温度使得过量的Co²⁺进一步氧化为Co³⁺,同时降低了表面氧缺陷浓度,从而得到计量比的Co₃O₄4/SiO₂催化剂．在所有的负载催化剂中Co₃O₄(200)/SiO₂催化剂表现出了最好的CO氧化催化性能,表明过量Co²⁺和表面氧缺陷的存在能够促进Co₃O₄催化CO氧化反应的活性.     

钴改性Fe3O4-MnO2催化转化生物质合成气制备液体燃料

本文制备了用于费托合成反应的钴改性Fe₃O₄-MnO₂双功能催化剂,并探究了钴负载量对Fe-Co协同效应的影响以及Fe₁Co_xMn₁催化剂的费托合成反应性能. 实验发现,在Fe₃O₄-Mn催化剂中加入Co可促进铁氧化物的还原、增加反应过程中铁位点的活性. 此外,Co的加入可增强Fe-Co金属间的电子转移,加强两者的协同作用,提高催化性能. Co负载较高的Fe₁Co_xMn₁催化剂可进一步促进加氢反应能力,使产品分布向短链烃方向转移. 在280 ^°C、2.0 MPa和3000 h^-1的最佳工况条件下,Fe₁Co₁Mn₁催化剂的液体燃料收率最高.     

利用EPR研究三氧化钼中氧还活性位点形成的温度依赖性

本文利用热处理还原法,利用三氧化钼诱导形成具有氧化还原活性的中间产物及其温度相关特性. 电子顺磁共振波谱(EPR)实验结果表明,热处理后在Mo^VI离子被还原成Mo^V离子并形成了超氧阴离子自由基O₂^-. 这两种活性中心的最佳热还原温度约300∽350 ^°C. 自350 ^°逐渐升温,两种EPR信号强度迅速下降,下降∽50%所对应的温度是400∽450 ^°C;当温度升至600 ^°C或更高时,EPR信号降至0. 结果表明,较高温处理或持续长时间处理都使热还原更容易发生,积累了越来越多的电子,在基底中形成类似于反铁磁耦合的电子离域. 随着离域程度增大,EPR信号强度开始下降并直至消失.     

煅烧温度对Cu/HMOR催化剂结构及其催化二甲醚羰基化反应性能影响

采用离子交换法在不同煅烧温度下制备HMOR负载Cu(Cu/HMOR)催化剂,用于催化二甲醚(DME)羰基化合成乙酸甲酯(MA)反应. 活性测试结果表明430 oC煅烧制得Cu/HMOR具有较好催化活性,在210 oC、1.5 MPa、空速4883 h^-1下DME转化率为97.2%,MA选择性为97.9%. 对催化剂进行X射线衍射、N₂物理吸附、NH₃程序升温脱附、CO程序升温脱附及拉曼方法表征. 催化剂经一定的煅烧温度有利于Cu离子迁移及扩散和硝酸铜完全分解,从而使HMOR载体具有较多的酸性活性位、大比表面、适宜的微孔结构以及更多的CO吸附位.     

海胆状CoCu双金属纳米复合材料的合成及其在甘油氢解制丙二醇中的催化性能

以Ru为多相成核剂和硬脂酸为表面活性剂,在多元醇溶液中合成了CoCu双金属纳米复合物,并在甘油选择性氢解制丙二醇中评价了其催化性能．结果表明,硬脂酸作为结构导向剂可诱使Co纳米晶沿着一维方向生长,形成纳米线．当Co²⁺和Cu²⁺共存于多元醇溶液中,由于Cu²⁺较高的氧化还原电位,首先被还原成Cu⁰,进而增长成100～300 nm的球形粒子．在Cu粒子表面,Co²⁺被还原成核,在表面活性剂的结构导向作用下生长为长度为100～500 nm的纳米棒,从而形成海胆状CoCu双金属纳米复合结构．在甘油选择性氢解制丙二醇反应中,海胆状CoCu双金属复合催化剂的单位表面活性与丙二醇选择性均明显高于单金属Co纳米线和Cu球形粒子,在Co₉₀Cu₁₀催化剂上获得33%的丙二醇收率．这可能是由于Co和Cu界面的协同效应促进了甘油的转化所致．     

介孔SO42-/Zr-SBA-15催化废弃油制生物柴油

采用廉价的无机锆源(无水硝酸锆)通过一步法合成表面含强Lewis酸位的SO₄^2-/Zr-SBA-15,该催化剂材料在废弃食用油和甲醇酯交换制生物柴油过程中表现出良好的催化活性和选择性. 实验考察了酯交换反应的最佳条件为：反应温度160 oC、反应时间12 h、催化剂Zr:Si为0.11、催化剂用量为10%、醇油比30:1. SO₄^2-/Zr-SBA-15在最佳反应条件下可使甘油三酯的转化率达到92.3%,脂肪酸甲酯的产率为91.7%. SO₄^2-/Zr-SBA-15具有高比表面积的介孔结构和表面酸性,且具有良好的反应稳定性和重复性,反应7次后的脂肪酸甲酯的产率仍稳定保持在74 ±1%.     

活化气氛对钼基合成醇催化剂的结构和性能的影响

Activated carbon supported Mo-based catalysts were prepared and reduced under different activation atmospheres, including pure H₂, syngas (H₂/CO=2/1), and pure CO. The catalysts structures were characterized by X-ray diffraction, X-ray absorption fine structure, and in situ diffuse reflectance infrared Fourier transform spectroscopy. The catalytic performance for the higher alcohol synthesis from syngas was tested. The pure H₂ treatment showed a high reduction capacity. The presence of a large amount of metallic Co⁰. and low valence state Mo^φ+ (0<φ<2) on the surface suggested a super activity for the CO dissociation and hydrogenation, which promoted hydrocarbons formation and reduced the alcohol selectivity. In contrast, the pure CO-reduced catalyst had a low reduction degree. The Mo and Co species at the catalyst mainly existed in the form of Mo⁴⁺ and Co²⁺. The syngas-reduced catalyst showed the highest activity and selectivity for the higher alcohols synthesis. We suggest that the syngas treatment had an appropriate reduction capacity that is between those of pure H₂ and pure CO and led to the coexistence of multivalent Co species as well as the enrichment of Mo^δ+ on the catalyst''s surface. The synergistic effects between these active species provided a better cooperativity and equilibrium between the CO dissociation, hydrogenation and CO insertion and thus contributed beneficially to the formation of higher alcohols.     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Hybrid Wavelength and Code Division Multiple Access in Optical Networks

A review of schemes for multiple access in fiber optic networks shows that a hybrid of wavelength and code division multiple access (WCDMA) combines the best features of both. In particular, the hybrid scheme retains the large information carrying capacity of wavelength division multiple access (WDMA) and flexibility of code division multiple access (CDMA). In this paper WDMA, optical CDMA (OCDMA), and WCDMA networks are discussed. In OCDMA networks, concept of incoherent and coherent coding including inverse decoding and matched filter is introduced. The delay performance of both WDMA and WCDMA networks, under the simple suboptimum access protocols based on cyclic search, is computed. It has been shown quantitatively that tuning delay significantly affects the delay performance of both WDMA and WCDMA networks. Futhermore, delay performance of WCDMA networks is always better than the WDMA networks for the same tuning delay, load, and number of users.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.