邻苯二酚和对苯二酚在钴氢氧化物膜修饰玻碳电极上的选择性测定

通过镀膜/循环伏安法制备了钴氢氧化物膜修饰的玻碳电极。该修饰电极对邻苯二酚(CA)和对苯二酚(HQ)具有较强的电催化活性。考察了支持电解质酸度对邻苯二酚和对苯二酚电化学响应的影响,选用0.1 mol/LPBS(pH 10.0)作为支持电解质。利用差示脉冲伏安法(DPV)对邻苯二酚和对苯二酚进行选择性检测,当两者浓度同时改变时,邻苯二酚和对苯二酚在6～100μmol/L范围内氧化峰电流与其浓度呈良好的线性关系,检出限分别为2×10–7,5×10–7mol/L(S/N=3)。钴氢氧化物膜电极具有较好的稳定性、重现性及较强的抗干扰能力,将此修饰电极应用于模拟水样中邻苯二酚和对苯二酚的测定,回收率为95.4%～100.4%。     

L-半胱氨酸/普鲁士蓝复合修饰玻碳电极的制备及电化学性能

通过电聚合方法和脉冲沉积技术将普鲁士蓝(PB)与L-半胱氨酸(L-Cys)修饰在玻碳电极(GCE)表面,制得复合膜化学修饰电极(L-Cys/PB/GCE/CME),利用循环伏安法和计时安培法研究了对苯二酚在L-Cys/PB/GCE/CME上的电化学特征。结果表明,在0.1 mol/L PBS(pH 7.0)缓冲溶液中,L-Cys/PB/GCE/CME对对苯二酚的电化学氧化具有明显的催化作用,氧化峰电流相对于在裸玻碳电极上增加了5倍。在最佳实验条件下,对苯二酚浓度在0.18~120μmol/L范围内,修饰电极的电流响应与对苯二酚浓度呈线性关系,其相关系数为0.9962,检出限(S/N=3)为0.065μmol/L。本研究制备的对苯二酚传感器具有较好的重复性、重现性、选择性与稳定性,用于实际水样中对苯二酚的测定,结果满意。     

聚L-半胱氨酸/多壁碳纳米管复合修饰电极同时测定邻苯二酚和对苯二酚

将羧基化多壁碳纳米管分散在L-半胱氨酸溶液中并滴涂在玻碳电极表面.将上述电极在pH 6.9的B-R缓冲溶液中,于-1.0～2.5 V的电位范围内进行电聚合,制备了聚L-半胱氨酸/多壁碳纳米管复合修饰电极(Pol-L-Cys/MWCNTs/GCE).研究发现,邻苯二酚和对苯二酚在聚L-半胱氨酸/多壁碳纳米管复合修饰电极上分别出现了一对氧化还原峰,且两者的氧化峰电位差达101 mV,提出了用微分脉冲伏安法同时测定邻苯二酚和对苯二酚的方法.氧化峰电流与邻苯二酚和对苯二酚的浓度在1.0×10-5～1.0×10-3mol·L-1呈线性关系,检出限(3S/N)均达1.0×10-5mol·L-1.修饰电极用于模拟样品中邻苯二酚和对苯二酚的测定,回收率在82.0%～107.0%之间.     

聚对苯二酚修饰玻碳电极的制备及其对抗坏血酸的催化氧化作用

采用循环伏安(CV)法制备了聚对苯二酚薄膜修饰玻碳电极,利用其电催化氧化作用建立了抗坏血酸的定量分析方法,探讨了其催化氧化机理。研究发现:在0.2 mol/L Na2HPO4-NaH2PO4(PBS,pH 7.0)缓冲溶液中,以0.1 mol/L KC l作支持电解质,聚对苯二酚修饰电极(PHQ/CME)对抗坏血酸(AA)存在灵敏的催化氧化作用,氧化峰电位负移177 mV。应用微分脉冲伏安法(DPV)对AA进行定量分析,其氧化峰电流与AA浓度在3.3×10-5~1.7×10-2mol/L和1.7×10-2~1.2×10-1mol/L范围内呈良好的线性关系,检出限为3.3×10-6mol/L。机理研究结果表明:PHQ/CME上带有的酚羟基与脱氢抗坏血酸自由基之间形成的氢键是电催化氧化的主要原因。     

纳米铂修饰玻碳电极对邻苯二酚的电化学氧化及测定

应用循环伏安法研究了邻苯二酚在纳米铂修饰玻碳(PtNPs/GC)电极上的电化学氧化行为。实验表明,PtNPs/GC电极对邻苯二酚有很强的电催化作用,其伏安扫描氧化峰电流随着温度的升高而增大,但氧化峰电位略有负移。常温下,邻苯二酚能自发在电极表面发生聚合反应,生成具有导电性的聚合膜,其催化氧化电流与邻苯二酚浓度在1.0×10-6mol/L~5.0×10-5mol/L范围内呈良好的线性关系,检出限为2.9×10-7mol/L。     

多壁碳纳米管修饰电极对对苯二酚的电催化作用

研究了多壁纳米碳管修饰电极的制备及其对对苯二酚的电催化作用。讨论了支持电解质种类、酸度、修饰层厚度和扫速等因素对对苯二酚伏安响应的影响 ,获得了较为优化的实验条件。在 0 .1mol/L磷酸盐 (pH 6 .0 )缓冲溶液中 ,采用示差脉冲伏安法测定对苯二酚 ,其浓度在 5 .0× 1 0 -6～ 1 .1× 1 0 -3 mol/L范围内与其氧化峰电流呈良好的线性关系 ,检出限达 2 .7× 1 0 -6mol/L。共存的多种金属离子、抗坏血酸及等量的苯酚、邻苯二酚等不干扰测定。该电极用于模拟废水样中对苯二酚的测定 ,结果令人满意     

苯胺在邻-氨基苯磺酸功能化的玻碳电极上聚合及其对抗坏血酸的电催化氧化

通过电氧化法将ABS分子以CN键共价键合在玻碳电极(GCE)表面,形成ABS分子单层膜修饰的GCE(ABS/GCE),在此电极上对AN进行电聚合,从而制备了聚苯胺/邻氨基苯磺酸复合膜修饰电极(PAN-ABS/GCE/CME).由于ABS中磺酸基功能团对PAN的掺杂作用使PAN在中性或碱性介质中都能呈现出较好的电化学活性.研究表明,PAN-ABS/GCE/CME在PBS(pH 6.8)中对AA的电氧化具有催化作用,其氧化峰电位为0.17 V,比在裸GCE上(0.39 V)负移了0.22 V,峰电流明显升高.AA在修饰电极上的氧化峰电流与其浓度在0.5～16.5 mmol/L范围内呈良好的线性关系,其线性回归方程为ipa(μA)=20.2+6.20CAA,r=0.9973; 检出限(3δ)为7.2 μmol/L,电极具有较好的稳定性和重现性.并采用计时电流法对AA催化氧化的扩散系数和催化速率常数进行了研究.     

碳纳米管/对氯四苯基锰卟啉修饰电极同时测定二羟基苯异构体

制备了碳纳米管/对氯四苯基锰卟啉修饰的玻碳电极,研究了三种二羟基苯异构体在该修饰电极上的电化学行为。由于碳纳米管独特的性能及与对氯四苯基锰卟啉特殊的协同效应,异构体在该修饰电极上的氧化峰电流均显著增大。利用差分脉冲伏安法(DPV)可同时检测三种异构体,在pH=6.5的磷酸盐缓冲溶液(PBS)中,邻苯二酚(CC)、间苯二酚(RC)、对苯二酚(HQ)峰电流与其浓度分别在0.8～280.0μmol/L、1.5～85.0μmol/L和0.4～200.0μmol/L范围内呈良好的线性关系,其检出限分别为0.5μmol/L、1.0μmol/L和0.2μmol/L。该电极具有良好重现性和稳定性。     

纳米金/Nafion/石墨烯修饰玻碳电极检测对苯二酚的研究

采用一步电化学共还原的方法将纳米金(AuNPs)、Nafion、电化学还原石墨烯(ERGO)修饰到玻碳电极(GCE)表面,制成修饰电极AuNPs/Nafion/ERGO/GCE。以扫描电镜对其进行表征,用循环伏安法和微分脉冲伏安法研究对苯二酚在该修饰电极上的电催化行为。优化了实验参数,对苯二酚在2.0～100μmol/L及100～800μmol/L浓度范围内与其氧化峰电流呈良好的线性关系,检出限为0.3μmol/L。用该修饰电极成功地进行了实际水样中对苯二酚含量的测定。     

邻苯二酚和对苯二酚在电活化玻碳电极上的电化学行为及同时测定

制备了电活化的玻碳电极,利用循环伏安法研究了邻苯二酚和对苯二酚在该电极上的电化学行为,结果表明该电极对两者的氧化还原具有很好的电催化能力。在0.1 mol/L PBS(pH 7.0)中,采用示差脉冲伏安法对对苯二酚和邻苯二酚分别测定和同时测定,对苯二酚和邻苯二酚的氧化峰电流与其浓度分别在3.0×10-7～1.2×10-5 mol/L和1.0×10-7～1.2×10-5 mol/L范围内呈良好的线性关系,检测限分别为1.0×10-7和6.34×10-8mol/L(S/N=3)。该法已用于模拟废水样中对苯二酚和邻苯二酚的测定。     

pMB/MWNTs/GC电极对水体中苯二酚异构体的同时测定

通过在多壁碳纳米管修饰玻碳电极上电聚合亚甲基蓝,制备了聚亚甲基蓝/碳纳米管/玻碳电极(pMB/MWNTs/GC)。用循环伏安法研究了3种苯二酚异构体在该电极上的电化学行为,结果表明,在pH7.0的磷酸盐缓冲溶液中,该修饰电极对苯二酚异构体的氧化表现出优异的电催化性能和选择性,对苯二酚、邻苯二酚和间苯二酚的氧化峰分别为0.104、0.203、0.609 V(vs.SCE),峰电位差值分别为99、406 mV。基于苯二酚异构体在pMB/MWNTs/GC修饰电极上的伏安行为,建立了苯二酚3种异构体同时分析的新方法。考察了各影响因素对测定的影响,最优实验条件下,在5.0×10-6~1.5×10-4mol.L-1范围内,3种苯二酚异构体的阳极峰电流与其浓度存在线性关系,检出限均为1.0×10-6mol.L-1。将该法用于水体及冲洗废液中苯二酚异构体含量的测定,结果满意。     

银掺杂聚L-甲硫氨酸修饰电极同时测定对苯二酚和邻苯二酚

用循环伏安法制备了银掺杂聚L-甲硫氨酸修饰玻碳电极,研究了对苯二酚和邻苯二酚在该修饰电极上的电化学行为,建立了同时测定对苯二酚和邻苯二酚的新方法.研究发现,在pH=5.0的磷酸盐缓冲溶液中,扫速为100 mV/s时,对苯二酚和邻苯二酚在银掺杂聚L-甲硫氨酸修饰玻碳电极上均出现1对氧化还原峰,峰电位分别为:Epa=0.228 V、Epc =0.162 V和Epa=0.347 V、Epc =0.287 V,二者的氧化峰电位差达119 mV,还原峰差达125 mV.在最佳的条件下,用差分脉冲伏安法同时测定邻苯二酚和对苯二酚的线性范围为3.00 ×10-6～1.00 ×10-4mol/L,检出限为8.0×10-7 mol/L(对苯二酚)和5.0×10-7 mol/L(邻苯二酚).此法用于废水样中对苯二酚和邻苯二酚的测定,获得满意结果.     

Simultaneous Determination of Hydroquinone and Catechol at a Glassy Carbon Electrode Modified with Multiwall Carbon Nanotubes

A simply and high selectively electrochemical method for simultaneous determination of hydroquinone and catechol has been developed at a glassy carbon electrode modified with multiwall carbon nanotubes (MWNT). It was found that the oxidation peak separation of hydroquinone and catechol and the oxidation currents of hydroquinone and catechol greatly increase at MWNT modified electrode in 0.20 M acetate buffer solution (pH 4.5). The oxidation peaks of hydroquinone and catechol merge into a large peak of 302 mV (vs. Ag/AgCl, 3 M NaCl) at bare glassy carbon electrode. The two corresponding well‐defined oxidation peaks of hydroquinone in the presence of catechol at MWNT modified electrode occur at 264 mV and 162 mV, respectively. Under the optimized condition, the oxidation peak current of hydroquinone is linear over a range from 1.0×10^?6 M to 1.0×10^?4 M hydroquinone in the presence of 1.0×10^?4 M catechol with the detection limit of 7.5×10^?7 M and the oxidation peak current of catechol is linear over a range from 6.0×10^?7 M to 1.0×10^?4 M catechol in the presence of 1.0×10^?4 M hydroquinone with the detection limit of 2.0×10^?7 M. The proposed method has been applied to simultaneous determination of hydroquinone and catechol in a water sample with simplicity and high selectivity.     

Enhanced Electrochemical Determination of Catechol and Hydroquinone Based on Pd Nanoparticles/Poly(Taurine) Modified Glassy Carbon Electrode

Here, Pd nanoparticles and poly(taurine) film was prepared on the glassy carbon electrode surface (Pd/Poly(TAU)/GCE) by the rapid electrochemical technique. The proposed composite surface was characterized by scanning electron microscopy(SEM), X‐ray photoelectron spectroscopy(XPS) and electrochemical impedance spectroscopy(EIS). Enhanced electron transfer ability and higher electroactive surface area were achieved at Pd/Poly(TAU)/GCE as compared to the bare GCE and polymer film electrode. The new and highly stable Pd/Poly(TAU)/GCE was employed for the individual and simultaneous determination of hydroquinone and catechol which were environmentally toxic. Under the optimized conditions, HQ and CC were individually determined by using the differantial pulse voltammetry in the linear ranges of 0.008–100 μM and 0.001–100 μM with the detection limits of (LOD) 2.1 nM and 0.68 nM, respectively. In case of simultaneous determination, LODs were found as 10 nM and 0.88 nM for HQ and CC, respectively. The content of both analytes in the real sample analysis was evaluated in the river water and tap water successfully.     

A Novel Sensitive Electrochemical Sensor for the Simultaneous Determination of Hydroquinone and Catechol using Tryptophan-Functionalized Graphene

A novel tryptophan-functionalized graphene nanocomposite was employed for the simultaneous determination of hydroquinone and catechol. The analyte electrochemical behavior on the surface of tryptophan-functionalized graphene was investigated by cyclic voltammetry and differential pulse voltammetry. Compared to conventional graphene, enhanced peak currents were obtained that were attributed to the large number of defects on tryptophan-functionalized graphene that accelerated electron transfer between the electrode and analytes. The peak potential difference between hydroquinone and catechol at the tryptophan-functionalized graphene modified glassy carbon electrode was 104 millivolt, which was sufficiently wide to simultaneously determine hydroquinone and catechol. This method was used for the analysis of tap water.     

纳米氧化铜-碳纳米管修饰玻碳电极同时检测邻、对苯二酚

以商品化纳米氧化铜和羧化碳纳米管作为玻碳电极修饰材料,结合了两种材料的放大电信号和电催化性能,所构建的复合物修饰电极可区分性质相近的同分异构体邻苯二酚和对苯二酚的信号,同时可进一步放大两种酚的峰电流。 因此该基于纳米氧化铜和碳纳米管的电化学传感器可用于邻苯二酚和对苯二酚的同时检测。 采用循环伏安法对复合物中两种材料的比例、修饰量以及支持电解质pH进行了优化:纳米氧化铜和碳纳米管质量比为5∶1,修饰量为9 μL,pH=7.4的磷酸盐缓冲溶液被用作电解质溶液。 在优化的条件下,邻苯二酚和对苯二酚的微分脉冲伏安扫描峰电流与浓度在6.0×10^-7~3.0×10^-3 mol/L范围内均呈良好的线性关系,检出限(S/N=3)分别为1.0×10^-7和1.6×10^-7 mol/L。 该方法具有成本低、操作简便、快速的特点,对实际水样的加标回收率在94.6%~101.1%范围内,具有较好的实际应用前景。     

On-column electrochemical redox derivatization for enhancement of separation selectivity of liquid chromatography use of redox reaction as secondary chemical equilibrium

An on-column electrochemical redox derivatization for enhancement of high-performance liquid chromatography (HPLC) separation selectivity is presented using electrochemically modulated liquid chromatography (EMLC) and porous graphitic carbon (PGC) as the packing material. PGC therefore serves two purposes: it acts both as a chromatographic stationary phase and as a working electrode. The capability of on-column electrochemical redox derivatization was evaluated using hydroquinone and catechol as model compounds. By manipulation of the applied potential, hydroquinone and catechol will migrate as equilibrium mixtures, hydroquinone and p-benzoquinone and catechol and o-benzoquinone in the potential region of 25-125 mV and 150-200 mV (vs. Ag/AgCl), respectively. These redox reactions can be used as secondary chemical equilibria so that the corresponding equilibrium mixtures elute as single peaks and their retention times can be controlled by alterations in the potential applied to the PGC stationary phase. Homogeneity of the redox activity of the PGC stationary phase applied potential was also demonstrated.     

Electrochemical determination of the surface composition of Pd–Pt core–shell nanoparticles

Different amounts of Pt atoms were deposited onto the surface of Pd nanoparticles supported on carbon black by hydroquinone reduction method in anhydrous ethanol. Here, we surveyed electrochemical probing of surface compositions of Pd–Pt surface alloys. They were calculated from hydrogen desorption, carbon monoxide adlayer oxidation, and reduced carbon dioxide oxidation charges. The surface composition of Pt drastically increased up to Pt[0.3]/Pd/C (23.1 at.% of Pt) and then approached that of pure Pt with the moderate rate of increase.     

Simultaneous determination of catechol and hydroquinone by carbon paste electrode modified with hydrophobic ionic liquid-functionalized SBA-15

Hydrophobic ionic liquid-functionalized SBA-15 modified carbon paste electrode (CPSPE) was fabricated, and its electrochemical performance was investigated by cyclic voltammetry, electrochemical impedance spectra, and chronocoulometry in K₃Fe(CN)₆/K₄Fe(CN)₆ solution. Compared with carbon paste electrode (CPE) and SBA-15 modified carbon paste electrode (CSPE), the electron transfer ability was in the sequence as: CPSPE>CSPE>CPE. Meanwhile, the electrocatalytic activity of CPSPE to catechol and hydroquinone was evaluated by cyclic voltammetry, and then, the linear concentration ranges were obtained by the amperometric detection from 2.0?×?10^-5 to 3.2?×?10^-4 M for catechol and 5.0?×?10^-5 to 5.5?×?10^-4 M for hydroquinone, with the detection limits of 5.0?×?10^-7 and 6.0?×?10^-7 M, respectively. The advantages of both ionic liquids and heterogeneous supports made CPSPE exhibit high electrocatalytic activity towards the redox of catechol and hydroquinone by significantly improving their reversibility and enhancing their peak currents. In addition, the present method was applied to the determination of catechol and hydroquinone in artificial wastewater sample, and the results were satisfactory.     

Molecularly imprinted polymers microsphere prepared by precipitation polymerization for hydroquinone recognition

A one-step precipitation polymerization synthesis was adopted for the preparation of molecularly imprinted polymers (MIPs) by using hydroquinone as a template molecule. The transmission electron microscopy (TEM) exhibited that the polymers were uniform spheres with the diameter of about 700 nm. The results of adsorption experiments showed that the microspherical imprinted polymers possessed fast adsorption dynamics. Compared to the structurally similar compounds, catechol and resorcinol, the MIPs exhibited a high recognizable capacity to hydroquinone. And the electrochemical sensor fabricated by modifying the prepared MIPs microsphere on the glassy carbon electrode surface was used to detect the hydroquinone concentration. The current response was proportional to the concentration of hydroquinone in the range of 2.0 x 10(-6) to 1.0 x 10(-4)mol/L with the detection limit of 1.0 x 10(-6)mol/L.