Radiation synthesis and characterization of poly(N,N-dimethylaminoethyl methacrylate-co-N-vinyl 2-pyrrolidone) hydrogels

In this study, radiation synthesis and characterization of swelling behavior and network structure of poly(N,N-dimethylaminoethyl methacrylate) (PDMAEMA), and poly(N,N-dimethylaminoethyl methacrylate-co-N-vinyl 2-pyrrolidone) (P(DMAEMA-co-VP)), hydrogels were investigated. PDMAEMA and P(DMAEMA-co-VP) hydrogels in the rod forms were prepared by irradiating the ternary mixtures of DMAEMA/VP/cross-linking agent, ethyleneglycol dimethacrylate (EGDMA), by gamma rays at ambient temperature. In composition ranges where the three components were completely miscible, water was also added to the ternary mixture to provide the formation of homogeneous polymerization and gelation. The influence of irradiation dose, comonomer, VP, and cross-linking agent, EGDMA, content on the total percentage gelation and monomer conversion were investigated. The effect of pH and temperature on the swelling behavior of hydrogels have also been examined. Hydrogels showed typical pH response and temperature responses, such as low-pH and low temperature swelling and high-pH and high temperature deswelling. Polymer-solvent interaction parameter (χ) and enthalpy and entropy changes appearing in the χ parameter for the P(DMAEMA-co-VP)-water system were determined by using Flory-Rehner theory of swelling equilibrium. The negative values for ΔH and ΔS indicate that prepared pure PDMAEMA and P(DMAEMA-co-VP) hydrogels have lower critical solution temperature (LCST) and Flory-Rehner theory of swelling equilibrium provides a satisfactory agreement to the experimental swelling data of the hydrogels.     

Preparation and Characterization of Poly(N‐Vinylpyrrolidone‐co‐Methacrylic Acid) Hydrogels

In this study, N‐vinylpyrrolidone (VP)/methacrylic acid (MAA) copolymers have been prepared at three different mole percents, the methacrylic acid composition being around 5, 10, 15%. MAA and VP monomer mixtures have been irradiated in ⁶⁰Co‐γ source at different irradiation doses and percent conversions have been determined gravimetrically. ～80% conversion of monomers into hydrogels were performed at 3.4 kGy irradiation dose. These hydrogels were swollen in distilled water at pH 4.0, 7.0, and 9.0. P(VP/MAA) hydrogel which contains 5% methacrylic acid showed the maximum % swelling at pH 9.0 in water. Diffusion of water was found to be of non‐Fickian character. Diffusion coefficients of water in P(VP/MAA) hydrogels were calculated. Initial swelling rates of P(VP/MAA) hydrogels increased with increasing pH and MAA content in hydrogels. Swelling kinetics of P(VP/MAA) hydrogels was found to be of second order. Thermal behavior of PMAA, PVP and P(VP/MAA) hydrogel were investigated by thermal analysis. P(VP/MAA) hydrogel gained new thermal properties and the temperature for maximum weight loss and temperature for half‐life of P(VP/MAA) hydrogel were determined.     

Swelling and drug release behavior of poly(2-hydroxyethyl methacrylate/itaconic acid) copolymeric hydrogels obtained by gamma irradiation

The new copolymeric hydrogels based on 2-hydroxyethyl methacrylate (HEMA) and itaconic acid (IA) were prepared by gamma irradiation, in order to examine the potential use of these hydrogels in controlled drug release systems. The influence of IA content in the gel on the swelling characteristics and the releasing behavior of hydrogels, and the effect of different drugs, theophylline (TPH) and fenethylline hydrochloride (FE), on the releasing behavior of P(HEMA/IA) matrix were investigated in vitro. The diffusion exponents for swelling and drug release indicate that the mechanisms of buffer uptake and drug release are governed by Fickian diffusion. The swelling kinetics and, therefore, the release rate depends on the matrix swelling degree. The drug release was faster for copolymeric hydrogels with a higher content of itaconic acid. Furthermore, the drug release for TPH as model drug was faster due to a smaller molecular size and a weaker interaction of the TPH molecules with(in) the P(HEMA/IA) copolymeric networks.     

K-型卡拉胶/聚乙烯吡咯烷酮共混水凝胶的辐射合成

采用辐射技术合成了K 型卡拉胶 (KC) /聚乙烯吡咯烷酮 (PVP)共混水凝胶 ,研究了天然高分子KC、单体N 乙烯基吡咯烷酮 (N VP)、交联剂二甲基丙烯酸十四甘醇酯 ( 1 4G) ,辐照剂量以及剂量率等对辐射合成的KC/PVP共混水凝胶性质的影响 .实验发现 ,KC与适当比例的N VP共混后在一定剂量范围内辐照可得到高强度、高溶胀行为的KC/PVP共混水凝胶 ,随着共混凝胶内KC含量的相对增加 ,凝胶强度及溶胀性的能均显著提高 ,但合成该共混凝胶的最佳剂量却相对提前 ;加入 1 4G后降低了KC/PVP共混凝胶辐射合成最佳剂量 ,同时使KC/PVP共混凝胶的强度进一步提高 ;剂量、剂量率对KC/PVP共混凝胶的性质亦有很大的影响 .分析表明 ,KC与N VP共混后 ,在较低剂量下KC的降解被抑制 ,从而获得一种由物理交联的KC和化学交联的PVP形成的互穿网络 (IPN)凝胶     

Adsorption and release of terbinafine hydrochloride: Effects of adsorbents, additives, pH, and temperature

The paper describes results obtained within the study of factors affecting the process of an antifungal drug — terbinafine hydrochloride adsorption on two different adsorbents — charcoal and silicagel. The effects of the adsorbent area, pH value, temperature and additives (polymers — methyl cellulose and hydroxypropyl cellulose) were analyzed and their impact on the adsorption of terbinafine was derived. The increase of pH and temperature, and the presence of additives decreased the amount of terbinafine adsorbed on the adsorbents. Terbinafine is currently applied both perorally and topically. Hydrogels, i.e. compositions of a drug, additives and water, are, due to their advantageous properties, preferred topical dosage forms. Mass fraction of additives of 1 % to 4 % were studied from the view point of drug release. This study shows that both the sort and the concentration of polymers influence the drug release from hydrogels significantly.     

Terbinafine hydrochloride intercalated in montmorillonite: synthesis and characterization

The novel antifungal hybrid of terbinafine hydrochloride (TER-HCl)/montmorillonite was synthesized by the intercalation method under mechanical stirring. Intercalation of TER-HCl in the MMT galleries was characterized by X-ray diffraction (XRD), Fourier transform infrared spectra, elemental analysis (EA). and thermogravimetric analysis (TGA). The results from IR, TGA, and EA showed a difference in chemical composition of the MMT and the TER-HCl/MMT. XRD analysis showed that the basal spacing of montmorillonite significantly expanded from 1.53 to 2.79 nm. TER-HCl was successfully intercalated into the interlayer of MMT, and 28 % of TER-HCl was released after 48 h in 0.9 % (w/v) NaCl aqueous solution (pH 7) at 37 ± 0.5 °C. The antifungal activity of the hybrid against Candida albicans was evaluated using the inhibitory zone method and the minimum inhibitory concentration. The TER-HCl/MMT strongly inhibited C. albicans. These results show that TER-HCl/MMT can be useful in biomedical applications.     

Synthesis and swelling behavior of thermosensitive hydrogels based on N-substituted acrylamides and sodium acrylate

A series of hydrogels based on N-isopropylacrylamide, sodium acrylate, and N-tert-butylacrylamide were synthesized by free radical polymerization in a mixture of dioxane and water with tetra(ethylene glycol) diacrylate as the crosslinker and benzoyl peroxide as the initiator. The swelling behavior including the swelling rate of the crosslinked gels in water was studied with gravimetric method. The swelling ratio of the gel (0.1 mol% crosslinking) can reach 420 g/g at 20 °C and such a gel can release 96% of the water absorbed at 40 °C. The lower critical swelling temperature (LCST) of the copolymers can be adjusted by changing the chemical composition of the polymers. Such crosslinked gels can be potentially used as thermosensitive superabsorbent because of their high water uptake and thermal sensitivity.     

温度和pH双敏性PVME/CMCS水凝胶辐射交联制备及其性能

以聚甲基乙烯基醚(PVME)和羧甲基壳聚糖(CMCS)为原料, 采用电子束辐照交联方法制备聚甲基乙烯基醚/羧甲基壳聚糖(PVME/CMCS)水凝胶, 研究了温度、pH值、CMCS含量等对PVME/CMCS水凝胶溶胀度的影响, 同时以5-氟尿嘧啶(5-Fu)作模型药物, 初步探讨了凝胶药物释放性能. 结果表明, 辐射剂量在20—40 kGy时, 凝胶分数随辐射剂量的增加而快速增加, 辐射40 kGy以后趋于平衡. 在相同辐射剂量下, 随着体系中CMCS含量的增加, 凝胶分数反而减少. 该水凝胶具有一定的温度和pH敏感性, 其低临界溶解温度(LCST)在35 ℃左右, 并且在相同时间内和25及37 ℃下的溶胀反复可逆, 表现出较快的响应性. pH<3.0和pH>5.0时, 溶胀度较大; pH值为3.0~5.0时, 凝胶网络由于静电力收缩, 溶胀度较小. CMCS含量的增加和辐射剂量的减小均可提高凝胶载药量. 药物释放时间可通过改变体系中CMCS的含量和辐射剂量来调节.     

Anticancer drug release from poly(N-isopropylacrylamide/itaconic acid) copolymeric hydrogels

The drug uptake and release of anticancer drug from N-isopropylacrylamide/itaconic acid copolymeric hydrogels containing 0–3 mol% of itaconic acid irradiated at 48 kGy have been investigated. 5-Fluorouracil (5-FU) is used as a model anticancer drug. The effect of 5-FU solution on swelling characteristics of PNIPAAm and P(NIPAAm/IA) copolymeric hydrogels have also been studied. The percent swelling, equilibrium swelling, equilibrium water/5-FU content and diffusion constant values are evaluated for poly(N-isopropylacrylamide) (PNIPAAm) and poly(N-isopropylacrylamide/itaconic) (P(NIPAAm/IA)) hydrogels at 130 ppm of 5-FU solution at room temperature. Diffusion of 5-FU solution into the hydrogels has been found to be the non-Fickian type. Finally, the kinetics of drug release from the hydrogels are examined.     

Characterisation of N-vinyl-2-pyrrolidone-based hydrogels prepared by a Diels-Alder click reaction in water

N-vinyl-2-pyrrolidone-based hydrogels were prepared by the Diels-Alder reaction in water for the first time. Copolymers of N-vinyl-2-pyrrolidone(VP) and furfuryl methacrylate(FM) were synthesised by free radical polymerisation in toluene at 70 °C by using 2,2′-azobisisobutyronltrile as an initiator. Polymeric dienophile (PEG-AMI) was prepared from N-alaninyl maleimide (AMI) and poly(ethylene glycol) (PEG) by using N,N′-dicyclohexylcarbodiimide (DCC) as a dehydrating agent. The prepared dienes and dienophile were then dissolved in water and mixed, leading to gelation via Diels-Alder reaction after some time. The gelation times of different copolymers and PEG-AMI in different solvents and at different temperatures were measured by the vial inversion method, and the swelling behaviour of dried hydrogels was studied using a general gravimetric method. The gelation time was shorter in water than in organic solvents, and the gelation time decreased with the increase of temperature and FM content in copolymers. Conversely, the swelling ratios increased with the decrease of temperature and FM content in the copolymers. Disassembly experiments suggested that N,N-dimethylformamide (DMF) could accelerate the retro-DA reaction.     

Studies on preparation and properties of NIPAAm/hydrophobic monomer copolymeric hydrogels

A series of thermoreversible copolymeric hydrogels with various molar ratios of N-isopropylacrylamide (NIPAAm) and hydrophobic monomers such as 2,2,3,3,4,4,5,5-octafluoropentyl methacrylate (OFPMA) and n-butyl methacrylate (BMA) were prepared by emulsion polymerization. The effect of hydrophobic monomer on the swelling behavior and mechanical properties of the present copolymeric hydrogels was investigated. Results showed that the equilibrium swelling ratio and critical gel transition temperature (CGTT) decreased with an increase of the content of hydrophobic monomer, but the gel strength of the gel increased with an increase of the content of hydrophobic monomer. Due to stronger hydrophobicity of OFPMA, the NIPAAm/OFPMA copolymeric hydrogels had lower swelling ratios and higher gel strengths than NIPAAm/BMA copolymeric gels.     

Rapid swelling and deswelling in cryogels of crosslinked poly(N-isopropylacrylamide-co-acrylic acid)

Thermally sensitive hydrogels of poly[N-isopropylacrylamide (NIPA)-co-acrylic acid (AA)] hydrogels with N,N-methylene bisacrylamide (BIS) as crosslinker have been synthesized via a two-step procedure in which, the initial polymerisation is conducted for various times at 18 °C, this step being followed by polymerisation for one fixed time at −22 °C. The gravimetrically determined rates of swelling/deswelling for these materials termed “cryogels” prepared by this two-step polymerisation are much higher than those for the same type of hydrogel prepared via conventional methods (30 °C for 24 h). For example the time for the former xerogel to take up 70% of its final water content at 25 °C is just 18 min, compared with a time 300 min for the latter to attain the same uptake of water. During deswelling (shrinking) at 50 °C, which is above the lower critical temperature, the hydrogel loses 60 and 90 wt% water in 1 and 10 min respectively, compared to a timescale for the corresponding crosslinked copolymers prepared by conventional methods of about 100 min for 50 wt% water loss. A third type of hydrogel was made by a cold treatment (CT), for which the hydrogel prepared by conventional polymerization was stored in the frozen state. The swelling rate of these CT xerogels was the same as that for xerogels prepared by conventional polymerization, but the deswelling rate of the former was higher than that of the latter; for example, during deswelling, a loss of 90% water is attained within a few minutes.Scanning electron microscopy, digital photographs and flotation experiments together with swelling ratio studies reveal that the polymeric network of cryogel produced by the two-step polymerization method is characterized by an open structure with more pores and higher swelling ratio but lower mechanical strength compared to the conventional hydrogels. Such rapid response hydrogels have potential applications in separation and drug release technologies for example.     

Swelling behavior of strong polyelectrolyte poly(N-t-butylacrylamide-co-acrylamide) hydrogels

Temperature-sensitive ionic hydrogels based on N-t-butylacrylamide (TBA), acrylamide (AAm), 2-acrylamido-2-methylpropane sulfonic acid sodium salt (AMPS) and N,N^′-methylenebis(acrylamide) (BAAm) monomers were prepared. The molar ratio of TBA to the monomers AAm and AMPS was fixed at 60/40, while the AMPS content of the hydrogels was varied. The elastic modulus of the hydrogels was in the range of 347-447 Pa, much lower than the modulus of PAAm or poly(N-isopropylacrylamide) hydrogels due to the reduced crosslinking efficiency of BAAm in TBA/AAm copolymerization. The hydrogels exhibited swelling-deswelling transition in water depending on the temperature. Increasing ionic group (AMPS) content resulted in shifting of the transition temperature interval in which the deswelling takes place. The higher the ionic group content, the broader the temperature interval at the phase transition. Ionic hydrogels exhibited first-order reentrant conformational transitions in ethanol-water and in dimethylsulfoxide (DMSO)-water mixtures. The higher the ionic group content of the hydrogels the narrower the ethanol (or DMSO) range in which the reentrant phenomena occur. By taking into account the difference of the solvent mixture composition inside and outside the gel, the equilibrium swelling theory provided a satisfactory agreement to the experimental swelling data of the hydrogels immersed in the solvent mixtures.     

Swelling and drug release properties of acrylamide/carboxymethyl cellulose networks formed by gamma irradiation

Hydrogels based on acrylamide monomer (AM) and different ratios (5–20 wt%) of carboxymethyl cellulose (CMC) were synthesized by gamma irradiation. The hydrogels were characterized in terms of gel content, swelling and drug release characters. The effect of temperature and pH on the degree of swelling was also studied. The results showed that the gel fraction of AM/CMC hydrogels decreases greatly with increasing the contents of CMC in the initial feeding solution. The kinetic study showed that the swelling of all the hydrogels tends to reach the equilibrium state after 5 h. However, the swelling of AM/CMC hydrogels was greater than the hydrogel based on pure AM. On the other hand, it was found that the swelling of all the hydrogels changes within the temperature range 30–40 °C and within the pH range 4–8. The AM/CMC hydrogels was evaluated for the possible use in drug delivery systems. In this respect, the release properties of methylene blue indicator, as a drug model, was investigated. It was found that the percentage release from the hydrogels increase with time to reach ～80% after 3 h at pH of 2 compared to ～100% at pH of 8.     

Rapid swelling and deswelling in cryogels of crosslinked poly(N-isopropylacrylamide-co-acrylic)

Thermally sensitive hydrogels of poly[N-isopropylacrylamide (NIPA)-co-acrylic(AA)] hydrogels with N,N-methylene bisacrylamide (BIS) as crosslinker have been synthesised via a two-step procedure in which, the initial polymerisation is conducted for various times at 18 °C, this step being followed by polymerisation for one fixed time at −22 °C. The gravimetrically determined rates of swelling/deswelling for these materials termed “cryogels” prepared by this two-step polymerisation are much higher than those for the same type of hydrogel prepared via conventional methods (30 °C for 24 h). For example the time for the former xerogel to take up 70% of its final water content at 25 °C is just 18 min, compared with a time 300 min for the latter to attain the same uptake of water. During deswelling (shrinking) at 50 °C, which is above the lower critical temperature, the hydrogel loses 60 and 90 wt.% water in 1 and 10 min respectively, compared to a timescale for the corresponding crosslinked copolymers prepared by conventional methods of about 100 min for 50 wt.% water loss. A third type of hydrogel was made by a cold treatment (CT), for which the hydrogel prepared by conventional polymerisation was stored in the frozen state. The swelling rate of these CT xerogels was the same as that for xerogels prepared by conventional polymerisation, but the deswelling rate of the former was higher than that of the latter; for example, during deswelling, a loss of 90% water is attained within a few minutes.Scanning electron microscopy, digital photographs and flotation experiments together with swelling ratio studies reveal that the polymeric network of cryogel produced by the two-step polymerisation method is characterised by an open structure with more pores and higher swelling ratio but lower mechanical strength compared to the conventional hydrogels. The polymerisation was taking place on moderate freezing condition and the hydrogel was stored in a frozen state and subsequent thawing of polymer to be very useful the acceleration the response rate of this kind hydrogels. Such rapid response hydrogels have potential applications in separation and drug release technologies for example.     

Effects of synthesis-solvent on swelling and elastic properties of poly(N-isopropylacrylamide) hydrogels

Thermosensitive N-isopropylacrylamide (NIPA) hydrogels were synthesized by a free radical copolymerization with N,N′-methylenebisacrylamide (MBAA) in four solvents: water, ethanol, acetone and N,N-dimethylformamide. The swelling and elastic properties of the hydrogels were affected by the synthesis-solvents; the hydrogels (e.g. NIPA/MBAA = 1000/50 mol/m³-pre-gel solution) synthesized in water have smaller swelling volume and larger shear modulus at 10 °C than those synthesized in amphiphilic solvents. The network structure of hydrogels was estimated in terms of the conversion and two sorts of effective crosslinking density based on the Flory theory and the concentration of crosslinker. The hydrogels synthesized in water can have the microscopic inhomogeneous network arising from the entanglement of polymer chains, while the hydrogels synthesized in amphiphilic solvents can have the homogeneous network arising from the polymer concentration lower than the pre-gel solution and can be similar in network structure to the lightly crosslinked hydrogel synthesized in water.     

Thermal behavior and network structure of poly(N‐vinyl‐2‐pyrrolidone‐crotonic acid) hydrogels prepared by radiation‐induced polymerization

Poly(N‐vinyl‐2‐pyrrolidone‐crotonic acid) [P(VP/CrA)] hydrogels were prepared by irradiating the ternary mixture of VP/CrA and crosslinking agent ethylene glycol dimethacrylate (EGDMA) in water by γ rays at ambient temperature. Differential scanning calorimetry and thermogravimetric analysis were performed to evaluate the thermal properties of ionized networks and to establish if they showed thermal differences that could be related to the CrA content in the gel system. The volume swelling ratio of P(VP/CrA) hydrogels were investigated as a function of the pH in the immersing solution. The volume swelling ratio of these hydrogels increased with an increase in pH and a decrease CrA content in the hydrogel. The volume swelling ratio of the hydrogels was also evaluated using an equation, based on the Flory—Huggins thermodynamic theory, the phantom network theory of James–Guth and Donnan theory of swelling of weakly charged ionic gels for determination of the molecular weight between crosslinks and the polymer–solvent interaction parameter (χ). Copyright © 2004 John Wiley & Sons, Ltd.     

Preparation and characterization of sodium carboxymethylcellulose/poly(N-isopropylacrylamide)/clay semi-IPN nanocomposite hydrogels

A new kind of pH-/temperature-responsive semi-interpenetrating polymer network hydrogels based on linear sodium carboxymethylcellulose (CMC) and poly(N-isopropylacrylamide) (PNIPA) cross-linked by inorganic clay (CMC/PNIPA/Clay hydrogel) was prepared. The temperature- and pH-responsive behaviors, the mechanical properties of these hydrogels were investigated. The CMC/PNIPA/Clay hydrogels exhibited a volume phase transition temperature around 32 °C with no significant deviation from the conventional PNIPA hydrogels. The swelling ratio of the CMC/PNIPA/Clay hydrogels gradually decreased with increasing the contents of clay. The influence of pH value on swelling behaviors showed that there is a maximum swelling ratio at pH 5.9. Moreover, the CMC/PNIPA/Clay hydrogels exhibited excellent mechanical properties with high tensile stress and elongation at break in excess of 1200%.     

Studies on copolymerization of N-isopropylacrylamide with poly(ethylene glycol) methacrylate

The paper describes the preparation and characterization of cross-linked homopolymers and copolymers of N-isopropyl acrylamide (NIPAAm) with poly(ethylene glycol) methacrylate (PEGMA, M_n = 526 g/mol). Several copolymer samples were prepared by taking varying amounts of monomers i.e. NIPAAm and PEGMA in the initial feed using hydrophilic (IRGACURE-2959) and hydrophobic (DURACURE-1173) photoinitiator. In order to investigate the effect of reaction conditions, copolymers were prepared below or above the lower critical solution temperature (LCST) using water or water:ethanol (50:50) as solvent and by varying the amounts of cross-linker. Hydrogels prepared under varying reaction conditions were characterized for its swelling behaviour (using optical microscope), phase transition temperature (using DSC) and morphology (using SEM). As expected LCST increased from 35 to 39 °C as PEGMA content in copolymers increased from 1 to 20% (w/w). However, the morphology of hydrogels was found to be independent on the reaction conditions.Copolymer films having an optimum combination of swelling and performance properties were evaluated as switchable cell culture membranes. Hepatic cancer cell lines (Hep G-2) was used to study the cell growth and detachment. Cell growth and detachment were found to be dependent on the copolymer composition. Cell viability was found comparable to trypsin which also supports application of these films as cell culture membrane.     

Synthesis and properties of biodegradable thermo- and pH-sensitive poly[(N-isopropylacrylamide)-co-(methacrylic acid)] hydrogels

Thermo- and pH-sensitive hydrogels were synthesized via the copolymerization of N-isopropylacrylamide (NIPAAm) and methacrylic acid (MAA) crosslinked with a biodegradable PEG-co-PCL macromolecular crosslinker under UV irradiation. Swelling measurements showed that temperature and pH sensitivity of the resultant hydrogels were highly dependent on the composition of the hydrogels as well as temperature and pH of the local medium. The pH and temperature dependence of the hydrogels displayed good reversibility. The hydrolytic degradation studies showed that the degradation rate of the hydrogels increased with the increasing content of MAA introduced in the hydrogels in pH 7.4 PBS solutions at 37 °C. The study on the release of BSA indicated that the release rate of BSA was higher at pH 7.4 than at pH 2.0, and increased with the increase of the MAA content in the hydrogels in pH 7.4 PBS solutions at 37 °C. These hydrogel materials are desirable for potential applications as smart drug delivery systems.